Induction motor load impact on power system eigenvalue sensitivity analysis

Load modelling plays an important role in power system dynamic stability assessment. One of the widely used methods in assessing load model impact on system dynamic response is parametric sensitivity analysis. A composite load model-based load sensitivity analysis framework is proposed. It enables comprehensive investigation into load modelling impacts on system stability considering the dynamic interactions between load and system dynamics. The effect of the location of individual as well as patches of composite loads in the vicinity on the sensitivity of the oscillatory modes is investigated. The impact of load composition on the overall sensitivity of the load is also investigated.

Phenolics in sugar cane juice : potential degradation by hydrogen peroxide and Fenton's reagent

The presence of colour in raw sugar plays a key role in the marketing strategy of the Australian raw sugar industry. Some sugars are relatively difficult to decolourise during refining and develop colour during storage. A new approach that might result in efficient and cost-effective colour removal during the sugar manufacturing process is the use of an advanced oxidation process (AOP), known as Fenton oxidation, that is, catalytic production of hydroxyl radicals from the decomposition of hydrogen peroxide using ferrous iron. As a first step towards developing this technology, this study determined the composition of colour precursors present in the juice of cane harvested by three different methods. The methods were harvesting cane after burning, harvesting the whole crop with half of the trash extracted and harvesting the whole crop with no trash extracted. The study also investigated the degradation at pH 3, 4 and 5 of a phenolic compound, caffeic acid (3,4–dihydroxycinnamic acid), which is present in sugar cane juice, using both hydrogen peroxide and Fenton’s reagent. The results show that juice expressed from whole crop cane has significantly higher colour than juices expressed from burnt cane. However, the concentrations of phenolic acids were lower in the juices expressed from whole crop cane. The main phenolic acids present in these juices were p-coumaric, vanillic, 2,3–dihydroxybenzoic, gallic and 3,4–dihydroxybenzoic acids. The degradation of caffeic acid significantly improved using Fenton’s reagent in comparison to hydrogen peroxide alone. The Fenton oxidation was optimum at pH 5 when up to ~86 % of caffeic acid degraded within 5 min.

Phenolics in sugar cane juice : potential degradation by hydrogen peroxide and Fenton’s reagent

The presence of colour in raw sugar plays a key role in the marketing strategy of the Australian raw sugar industry. Some sugars are relatively difficult to decolourise during refining and develop colour during storage. A new approach that might result in efficient and cost-effective colour removal during the sugar manufacturing process is the use of an advanced oxidation process (AOP), known as Fenton oxidation, that is, catalytic production of hydroxyl radicals from the decomposition of hydrogen peroxide using ferrous iron. As a first step towards developing this technology, this study determined the composition of colour precursors present in the juice of cane harvested by three different methods. The methods were harvesting cane after burning, harvesting the whole crop with half of the trash extracted and harvesting the whole crop with no trash extracted. The study also investigated the degradation at pH 3, 4 and 5 of a phenolic compound, caffeic acid (3,4–dihydroxycinnamic acid), which is present in sugar cane juice, using both hydrogen peroxide and Fenton’s reagent. The results show that juice expressed from whole crop cane has significantly higher colour than juices expressed from burnt cane. However, the concentrations of phenolic acids were lower in the juices expressed from whole crop cane. The main phenolic acids present in these juices were p-coumaric, vanillic, 2,3–dihydroxybenzoic, gallic and 3,4–dihydroxybenzoic acids. The degradation of caffeic acid significantly improved using Fenton’s reagent in comparison to hydrogen peroxide alone. The Fenton oxidation was optimum at pH 5 when up to ~86% of caffeic acid degraded within 5 min.

On the significance of omitted variables in intersection crash modeling

Advances in safety research—trying to improve the collective understanding of motor vehicle crash causes and contributing factors—rest upon the pursuit of numerous lines of research inquiry. The research community has focused considerable attention on analytical methods development (negative binomial models, simultaneous equations, etc.), on better experimental designs (before-after studies, comparison sites, etc.), on improving exposure measures, and on model specification improvements (additive terms, non-linear relations, etc.). One might logically seek to know which lines of inquiry might provide the most significant improvements in understanding crash causation and/or prediction. It is the contention of this paper that the exclusion of important variables (causal or surrogate measures of causal variables) cause omitted variable bias in model estimation and is an important and neglected line of inquiry in safety research. In particular, spatially related variables are often difficult to collect and omitted from crash models—but offer significant opportunities to better understand contributing factors and/or causes of crashes. This study examines the role of important variables (other than Average Annual Daily Traffic (AADT)) that are generally omitted from intersection crash prediction models. In addition to the geometric and traffic regulatory information of intersection, the proposed model includes many spatial factors such as local influences of weather, sun glare, proximity to drinking establishments, and proximity to schools—representing a mix of potential environmental and human factors that are theoretically important, but rarely used. Results suggest that these variables in addition to AADT have significant explanatory power, and their exclusion leads to omitted variable bias. Provided is evidence that variable exclusion overstates the effect of minor road AADT by as much as 40% and major road AADT by 14%.

Developing safer passengers through a school-based injury prevention program

Motor vehicle crashes are a leading cause of death among young people. Fourteen percent of adolescents aged 13-14 report passenger-related injuries within three months. Intervention programs typically focus on young drivers and overlook passengers as potential protective influences. Graduated Driver Licensing restricts passenger numbers, and this study focuses on a complementary school-based intervention to increase passengers’ personal- and peer-protective behavior. The aim of this research was to assess the impact of the curriculum-based injury prevention program, Skills for Preventing Injury in Youth (SPIY), on passenger-related risk-taking and injuries, and intentions to intervene in friends’ risky road behavior. SPIY was implemented in Grade 8 Health classes and evaluated using survey and focus group data from 843 students across 10 Australian secondary schools. Intervention students reported less passenger-related risk-taking six months following the program. Their intention to protect friends from underage driving also increased. The results of this study show that a comprehensive, school-based program targeting individual and social changes can increase adolescent passenger safety.

Efficient safety message dissemination for cooperative collision warning via context modelling

A Cooperative Collision Warning System (CCWS) is an active safety techno- logy for road vehicles that can potentially reduce traffic accidents. It provides a driver with situational awareness and early warnings of any possible colli- sions through an on-board unit. CCWS is still under active research, and one of the important technical problems is safety message dissemination. Safety messages are disseminated in a high-speed mobile environment using wireless communication technology such as Dedicated Short Range Communication (DSRC). The wireless communication in CCWS has a limited bandwidth and can become unreliable when used inefficiently, particularly given the dynamic nature of road traffic conditions. Unreliable communication may significantly reduce the performance of CCWS in preventing collisions. There are two types of safety messages: Routine Safety Messages (RSMs) and Event Safety Messages (ESMs). An RSM contains the up-to-date state of a vehicle, and it must be disseminated repeatedly to its neighbouring vehicles. An ESM is a warning message that must be sent to all the endangered vehi- cles. Existing RSM and ESM dissemination schemes are inefficient, unscalable, and unable to give priority to vehicles in the most danger. Thus, this study investigates more efficient and scalable RSM and ESM dissemination schemes that can make use of the context information generated from a particular traffic scenario. Therefore, this study tackles three technical research prob- lems, vehicular traffic scenario modelling and context information generation, context-aware RSM dissemination, and context-aware ESM dissemination. The most relevant context information in CCWS is the information about possible collisions among vehicles given a current vehicular traffic situation. To generate the context information, this study investigates techniques to model interactions among multiple vehicles based on their up-to-date motion state obtained via RSM. To date, there is no existing model that can represent interactions among multiple vehicles in a speciffic region and at a particular time. The major outcome from the first problem is a new interaction graph model that can be used to easily identify the endangered vehicles and their danger severity. By identifying the endangered vehicles, RSM and ESM dis- semination can be optimised while improving safety at the same time. The new model enables the development of context-aware RSM and ESM dissemination schemes. To disseminate RSM efficiently, this study investigates a context-aware dis- semination scheme that can optimise the RSM dissemination rate to improve safety in various vehicle densities. The major outcome from the second problem is a context-aware RSM dissemination protocol. The context-aware protocol can adaptively adjust the dissemination rate based on an estimated channel load and danger severity of vehicle interactions given by the interaction graph model. Unlike existing RSM dissemination schemes, the proposed adaptive scheme can reduce channel congestion and improve safety by prioritising ve- hicles that are most likely to crash with other vehicles. The proposed RSM protocol has been implemented and evaluated by simulation. The simulation results have shown that the proposed RSM protocol outperforms existing pro- tocols in terms of efficiency, scalability and safety. To disseminate ESM efficiently, this study investigates a context-aware ESM dissemination scheme that can reduce unnecessary transmissions and deliver ESMs to endangered vehicles as fast as possible. The major outcome from the third problem is a context-aware ESM dissemination protocol that uses a multicast routing strategy. Existing ESM protocols use broadcast rout- ing, which is not efficient because ESMs may be sent to a large number of ve- hicles in the area. Using multicast routing improves efficiency because ESMs are sent only to the endangered vehicles. The endangered vehicles can be identified using the interaction graph model. The proposed ESM protocol has been implemented and evaluated by simulation. The simulation results have shown that the proposed ESM protocol can prevent potential accidents from occurring better than existing ESM protocols. The context model and the RSM and ESM dissemination protocols can be implemented in any CCWS development to improve the communication and safety performance of CCWS. In effect, the outcomes contribute to the realisation of CCWS that will ultimately improve road safety and save lives.

Porous Ca-Si-based nanospheres : a potential intra-canal disinfectant-carrier for infected canal treatment

The aim of this study is to develop a new intra-canal disinfectant-carrier for infected canal treatment. To achieve this purpose, a new porous Ca-Si (CS)-based nanosphere was synthesized and characterized. Results showed that the nanospheres can infiltrate into dentinal tubules and released the ampicillin over one week time in a sustained manner. The release of ampicillin from spheres has significantly antibacterial property. Extensive and well-organized in vitro mineralization and crystallization of apatite were induced on the surface of dentin slices covered by CS nanospheres. All these features indicate that the porous CS nanospheres may be developed into a new intra-canal disinfectant-carrier for infected canal treatment.

Breaking organizational barriers for greening Australian

Sustainability is an issue for everyone. For instance, the higher education sector is being asked to take an active part in creating a sustainable future, due to their moral responsibility, social obligation, and their own need to adapt to the changing higher education environment. By either signing declarations or making public statements, many universities are expressing their desire to become role models for enhancing sustainability. However, too often they have not delivered as much as they had intended. This is particularly evident in the lack of physical implementation of sustainable practices in the campus environment. Real projects such as green technologies on campus have the potential to rectify the problem in addition to improving building performance. Despite being relatively recent innovations, Green Roof and Living Wall have been widely recognized because of their substantial benefits, such as runoff water reduction, noise insulation, and the promotion of biodiversity. While they can be found in commercial and residential buildings, they only appear infrequently on campuses as universities have been very slow to implement sustainability innovations. There has been very little research examining the fundamental problems from the organizational perspective. To address this deficiency, the researchers designed and carried out 24 semi-structured interviews to investigate the general organizational environment of Australian universities with the intention to identify organizational obstacles to the delivery of Green Roof and Living Wall projects. This research revealed that the organizational environment of Australian universities still has a lot of room to be improved in order to accommodate sustainability practices. Some of the main organizational barriers to the adoption of sustainable innovations were identified including lack of awareness and knowledge, the absence of strong supportive leadership, a weak sustainability-rooted culture and several management challenges. This led to the development of a set of strategies to help optimize the organizational environment for the purpose of better decision making for Green Roof and Living Wall implementation.

Unit commitment in power systems with plug-in hybrid electric vehicles

With the continued development of renewable energy generation technologies and increasing pressure to combat the global effects of greenhouse warming, plug-in hybrid electric vehicles (PHEVs) have received worldwide attention, finding applications in North America and Europe. When a large number of PHEVs are introduced into a power system, there will be extensive impacts on power system planning and operation, as well as on electricity market development. It is therefore necessary to properly control PHEV charging and discharging behaviors. Given this background, a new unit commitment model and its solution method that takes into account the optimal PHEV charging and discharging controls is presented in this paper. A 10-unit and 24-hour unit commitment (UC) problem is employed to demonstrate the feasibility and efficiency of the developed method, and the impacts of the wide applications of PHEVs on the operating costs and the emission of the power system are studied. Case studies are also carried out to investigate the impacts of different PHEV penetration levels and different PHEV charging modes on the results of the UC problem. A 100-unit system is employed for further analysis on the impacts of PHEVs on the UC problem in a larger system application. Simulation results demonstrate that the employment of optimized PHEV charging and discharging modes is very helpful for smoothing the load curve profile and enhancing the ability of the power system to accommodate more PHEVs. Furthermore, an optimal Vehicle to Grid (V2G) discharging control provides economic and efficient backups and spinning reserves for the secure and economic operation of the power system

Hospital outpatient responses to potential driving impairment due to prescribed medications

Driving and using prescription medicines that have the potential to impair driving is an emerging research area. To date it is characterised by a limited (although growing) number of studies and methodological complexities that make generalisations about impairment due to medications difficult. Consistent evidence has been found for the impairing effects of hypnotics, sedative antidepressants and antihistamines, and narcotic analgesics, although it has been estimated that as many as nine medication classes have the potential to impair driving (Alvarez & del Rio, 2000; Walsh, de Gier, Christopherson, & Verstraete, 2004). There is also evidence for increased negative effects related to concomitant use of other medications and alcohol (Movig et al., 2004; Pringle, Ahern, Heller, Gold, & Brown, 2005). Statistics on the high levels of Australian prescription medication use suggest that consumer awareness of driving impairment due to medicines should be examined. One web-based study has found a low level of awareness, knowledge and risk perceptions among Australian drivers about the impairing effects of various medications on driving (Mallick, Johnston, Goren, & Kennedy, 2007). The lack of awareness and knowledge brings into question the effectiveness of the existing countermeasures. In Australia these consist of the use of ancillary warning labels administered under mandatory regulation and professional guidelines, advice to patients, and the use of Consumer Medicines Information (CMI) with medications that are known to cause impairment. The responsibility for the use of the warnings and related counsel to patients primarily lies with the pharmacist when dispensing relevant medication. A review by the Therapeutic Goods Administration (TGA) noted that in practice, advice to patients may not occur and that CMI is not always available (TGA, 2002). Researchers have also found that patients' recall of verbal counsel is very low (Houts, Bachrach, Witmer, Tringali, Bucher, & Localio, 1998). With healthcare observed as increasingly being provided in outpatient conditions (Davis et al., 2006; Vingilis & MacDonald, 2000), establishing the effectiveness of the warning labels as a countermeasure is especially important. There have been recent international developments in medication categorisation systems and associated medication warning labels. In 2005, France implemented a four-tier medication categorisation and warning system to improve patients' and health professionals' awareness and knowledge of related road safety issues (AFSSAPS, 2005). This warning system uses a pictogram and indicates the level of potential impairment in relation to driving performance through the use of colour and advice on the recommended behaviour to adopt towards driving. The comparable Australian system does not indicate the severity level of potential effects, and does not provide specific guidelines on the attitude or actions that the individual should adopt towards driving. It is reliant upon the patient to be vigilant in self-monitoring effects, to understand the potential ways in which they may be affected and how serious these effects may be, and to adopt the appropriate protective actions. This thesis investigates the responses of a sample of Australian hospital outpatients who receive appropriate labelling and counselling advice about potential driving impairment due to prescribed medicines. It aims to provide baseline data on the understanding and use of relevant medications by a Queensland public hospital outpatient sample recruited through the hospital pharmacy. It includes an exploration and comparison of the effect of the Australian and French medication warning systems on medication user knowledge, attitudes, beliefs and behaviour, and explores whether there are areas in which the Australian system may be improved by including any beneficial elements of the French system. A total of 358 outpatients were surveyed, and a follow-up telephone survey was conducted with a subgroup of consenting participants who were taking at least one medication that required an ancillary warning label about driving impairment. A complementary study of 75 French hospital outpatients was also conducted to further investigate the performance of the warnings. Not surprisingly, medication use among the Australian outpatient sample was high. The ancillary warning labels required to appear on medications that can impair driving were prevalent. A subgroup of participants was identified as being potentially at-risk of driving impaired, based on their reported recent use of medications requiring an ancillary warning label and level of driving activity. The sample reported previous behaviour and held future intentions that were consistent with warning label advice and health protective action. Participants did not express a particular need for being advised by a health professional regarding fitness to drive in relation to their medication. However, it was also apparent from the analysis that the participants would be significantly more likely to follow advice from a doctor than a pharmacist. High levels of knowledge in terms of general principles about effects of alcohol, illicit drugs and combinations of substances, and related health and crash risks were revealed. This may reflect a sample specific effect. Emphasis is placed in the professional guidelines for hospital pharmacists that make it essential that advisory labels are applied to medicines where applicable and that warning advice is given to all patients on medication which may affect driving (SHPA, 2006, p. 221). The research program applied selected theoretical constructs from Schwarzer's (1992) Health Action Process Approach, which has extended constructs from existing health theories such as the Theory of Planned Behavior (Ajzen, 1991) to better account for the intention-behaviour gap often observed when predicting behaviour. This was undertaken to explore the utility of the constructs in understanding and predicting compliance intentions and behaviour with the mandatory medication warning about driving impairment. This investigation revealed that the theoretical constructs related to intention and planning to avoid driving if an effect from the medication was noticed were useful. Not all the theoretical model constructs that had been demonstrated to be significant predictors in previous research on different health behaviours were significant in the present analyses. Positive outcome expectancies from avoiding driving were found to be important influences on forming the intention to avoid driving if an effect due to medication was noticed. In turn, intention was found to be a significant predictor of planning. Other selected theoretical constructs failed to predict compliance with the Australian warning label advice. It is possible that the limited predictive power of a number of constructs including risk perceptions is due to the small sample size obtained at follow up on which the evaluation is based. Alternately, it is possible that the theoretical constructs failed to sufficiently account for issues of particular relevance to the driving situation. The responses of the Australian hospital outpatient sample towards the Australian and French medication warning labels, which differed according to visual characteristics and warning message, were examined. In addition, a complementary study with a sample of French hospital outpatients was undertaken in order to allow general comparisons concerning the performance of the warnings. While a large amount of research exists concerning warning effectiveness, there is little research that has specifically investigated medication warnings relating to driving impairment. General established principles concerning factors that have been demonstrated to enhance warning noticeability and behavioural compliance have been extrapolated and investigated in the present study. The extent to which there is a need for education and improved health messages on this issue was a core issue of investigation in this thesis. Among the Australian sample, the size of the warning label and text, and red colour were the most visually important characteristics. The pictogram used in the French labels was also rated highly, and was salient for a large proportion of the sample. According to the study of French hospital outpatients, the pictogram was perceived to be the most important visual characteristic. Overall, the findings suggest that the Australian approach of using a combination of visual characteristics was important for the majority of the sample but that the use of a pictogram could enhance effects. A high rate of warning recall was found overall and a further important finding was that higher warning label recall was associated with increased number of medication classes taken. These results suggest that increased vigilance and care are associated with the number of medications taken and the associated repetition of the warning message. Significantly higher levels of risk perception were found for the French Level 3 (highest severity) label compared with the comparable mandatory Australian ancillary Label 1 warning. Participants' intentions related to the warning labels indicated that they would be more cautious while taking potentially impairing medication displaying the French Level 3 label compared with the Australian Label 1. These are potentially important findings for the Australian context regarding the current driving impairment warnings about displayed on medication. The findings raise other important implications for the Australian labelling context. An underlying factor may be the differences in the wording of the warning messages that appear on the Australian and French labels. The French label explicitly states "do not drive" while the Australian label states "if affected, do not drive", and the difference in responses may reflect that less severity is perceived where the situation involves the consumer's self-assessment of their impairment. The differences in the assignment of responsibility by the Australian (the consumer assesses and decides) and French (the doctor assesses and decides) approaches for the decision to drive while taking medication raises the core question of who is most able to assess driving impairment due to medication: the consumer, or the health professional? There are pros and cons related to knowledge, expertise and practicalities with either option. However, if the safety of the consumer is the primary aim, then the trend towards stronger risk perceptions and more consistent and cautious behavioural intentions in relation to the French label suggests that this approach may be more beneficial for consumer safety. The observations from the follow-up survey, although based on a small sample size and descriptive in nature, revealed that just over half of the sample recalled seeing a warning label about driving impairment on at least one of their medications. The majority of these respondents reported compliance with the warning advice. However, the results indicated variation in responses concerning alcohol intake and modifying the dose of medication or driving habits so that they could continue to drive, which suggests that the warning advice may not be having the desired impact. The findings of this research have implications for current countermeasures in this area. These have included enhancing the role that prescribing doctors have in providing warnings and advice to patients about the impact that their medication can have on driving, increasing consumer perceptions of the authority of pharmacists on this issue, and the reinforcement of the warning message. More broadly, it is suggested that there would be benefit in a wider dissemination of research-based information on increased crash risk and systematic monitoring and publicity about the representation of medications in crashes resulting in injuries and fatalities. Suggestions for future research concern the continued investigation of the effects of medications and interactions with existing medical conditions and other substances on driving skills, effects of variations in warning label design, individual behaviours and characteristics (particularly among those groups who are dependent upon prescription medication) and validation of consumer self-assessment of impairment.

Bayesian hierarchical analysis on crash prediction models

Traditional crash prediction models, such as generalized linear regression models, are incapable of taking into account the multilevel data structure, which extensively exists in crash data. Disregarding the possible within-group correlations can lead to the production of models giving unreliable and biased estimates of unknowns. This study innovatively proposes a -level hierarchy, viz. (Geographic region level – Traffic site level – Traffic crash level – Driver-vehicle unit level – Vehicle-occupant level) Time level, to establish a general form of multilevel data structure in traffic safety analysis. To properly model the potential cross-group heterogeneity due to the multilevel data structure, a framework of Bayesian hierarchical models that explicitly specify multilevel structure and correctly yield parameter estimates is introduced and recommended. The proposed method is illustrated in an individual-severity analysis of intersection crashes using the Singapore crash records. This study proved the importance of accounting for the within-group correlations and demonstrated the flexibilities and effectiveness of the Bayesian hierarchical method in modeling multilevel structure of traffic crash data.

Potential retrofitting of existing campus buildings to green buildings

Green building is building that the focus is to maximize the energy efficiency and resources used. While, retrofitting is the process of renovate or refurnish the existing building. Therefore by retrofit existing buildings that comply with green building requirement, it improves the environmental attributes of the buildings. In Malaysia, existing buildings and its communities contribute over 40% of green house gases to the environment. This paper describes a study that explores the potential to retrofit existing campus buildings that response to sustainable green building standard. A validation survey was carried out and the data collected was analysed using SPSS in order to confirm the significance of retrofitting Universiti Teknologi Malaysia (UTM) buildings toward green building initiative. The results show that all the twenty eight identified green elements recorded average index of higher than 3.5 which means that there is significant needs to retrofit the existing buildings to green buildings. This study concludes that it is urgently need for the campus to response to green building requirements in order to achieve higher energy effeciency and this can be done through effective etrofitting of existing buildings.

Wing shape as a potential discriminator of morphologically similar pest taxa within the Bactrocera dorsalis species complex (Diptera: Tephritidae)

Four morphologically cryptic species of the Bactrocera dorsalis fruit fly complex (B. dorsalis s.s., B. papayae, B. carambolae and B. philippinensis) are serious agricultural pests. As they are difficult to diagnose using traditional taxonomic techniques, we examined the potential for geometric morphometric analysis of wing size and shape to discriminate between them. Fifteen wing landmarks generated size and shape data for 245 specimens for subsequent comparisons among three geographically distinct samples of each species. Intraspecific wing size was significantly different within samples of B. carambolae and B. dorsalis s.s. but not within samples of B. papayae or B. philippinensis. Although B. papayae had the smallest wings (average centroid size=6.002 mm±0.061 SE) and B. dorsalis s.s. the largest (6.349 mm±0.066 SE), interspecific wing size comparisons were generally non-informative and incapable of discriminating species. Contrary to the wing size data, canonical variate analysis based on wing shape data discriminated all species with a relatively high degree of accuracy; individuals were correctly reassigned to their respective species on average 93.27% of the time. A single sample group of B. carambolae from locality 'TN Malaysia' was the only sample to be considerably different from its conspecific groups with regards to both wing size and wing shape. This sample was subsequently deemed to have been originally misidentified and likely represents an undescribed species. We demonstrate that geometric morphometric techniques analysing wing shape represent a promising approach for discriminating between morphologically cryptic taxa of the B. dorsalis species complex.

Investigating the potential value of individual parameters of histological grading systems in a sheep model of cartilage damage : the modified Mankin method

A total histological grade does not necessarily distinguish between different manifestations of cartilage damage or degeneration. An accurate and reliable histological assessment method is required to separate normal and pathological tissue within a joint during treatment of degenerative joint conditions and to sub-classify the latter in meaningful ways. The Modified Mankin method may be adaptable for this purpose. We investigated how much detail may be lost by assigning one composite score/grade to represent different degenerative components of the osteoarthritic condition. We used four ovine injury models (sham surgery, anterior cruciate ligament/medial collateral ligament instability, simulated anatomic anterior cruciate ligament reconstruction and meniscal removal) to induce different degrees and potentially 'types' (mechanisms) of osteoarthritis. Articular cartilage was systematically harvested, prepared for histological examination and graded in a blinded fashion using a Modified Mankin grading method. Results showed that the possible permutations of cartilage damage were significant and far more varied than the current intended use that histological grading systems allow. Of 1352 cartilage specimens graded, 234 different manifestations of potential histological damage were observed across 23 potential individual grades of the Modified Mankin grading method. The results presented here show that current composite histological grading may contain additional information that could potentially discern different stages or mechanisms of cartilage damage and degeneration in a sheep model. This approach may be applicable to other grading systems.