624 resultados para logs
Resumo:
This research aims to set whether is possible to build spatial patterns over oil fields using DFA (Detrended Fluctuation Analysis) of the following well logs: sonic, density, porosity, resistivity and gamma ray. It was employed in the analysis a set of 54 well logs from the oil field of Campos dos Namorados, RJ, Brazil. To check for spatial correlation, it was employed the Mantel test between the matrix of geographic distance and the matrix of the difference of DFA exponents of the well logs. The null hypothesis assumes the absence of spatial structures that means no correlation between the matrix of Euclidean distance and the matrix of DFA differences. Our analysis indicate that the sonic (p=0.18) and the density (p=0.26) were the profiles that show tendency to correlation, or weak correlation. A complementary analysis using contour plot also has suggested that the sonic and the density are the most suitable with geophysical quantities for the construction of spatial structures corroborating the results of Mantel test
Resumo:
Subsurface stratigraphic analysis of Devonian strata from the Rio do Peixe Basin, newly recognized by palynological studies, has resulted in the identification of two new lithostratigraphic units assembled in the Santa Helena Group. The Pilões Formation, the lower unit, is composed mainly of dark mudstones and medium-tovery fine-grained sandstones, with minor conglomerates and breccias. The Triunfo Formation, the upper unit, comprises whitish grey, kaolinitic, coarse-grained to conglomeratic, cross stratified sandstones and conglomerates, with interbedded mudstones and fine-grained sandstones. These units were characterized using cores, sidewall and cuttings samples, conventional logs and image log, from three wells drilled by PETROBRAS, and 3D seismic data. The Pilões Formation is interpreted as prodeltaic facies, with lesser associated subaqueous talus, debrite and sandy turbidite lobe facies, distal part of fandelta and braided fluviodeltaic facies of Triunfo Formation. The Santa Helena Group corresponds to the Lower Devonian tectono-sequence deposited in a NW-SE-trending graben during a transgressiveregressive cycle. With 343 meters of thickness (isochore) in well 1-PIL-1-PB (Pilões 1), this sequence has a non-conformity at the lower boundary and its upper boundary is an unconformity with the Lower Cretaceous tectono-sequence (Rio do Peixe Group), that represents a hiatus of about 265 million years. Ignimbrites and coignimbrite breccias (Poço da Jurema volcanic breccia), related to an unknown pyroclastic volcanic event, were recognized at the northern margin of the Sousa halfgraben. Evidence from well data suggests that this event is coeval with the Devonian graben filling. The present study indicates a polyhistorical tectono-volcanosedimentary evolution of the basin. This lithostratigraphic update brings new perspectives for geological research in the Rio do Peixe Basin, as well as in other inland basins of the Northeastern of Brazil. The results of the research also contribute to the kwnoledge of the Borborema Province and western Gondwana paleogeography during the Early Devonian.
Resumo:
The distribution of diagenetic alterations in Late Cenomanian siliciclastic reservoirs from Potiguar Basin was influenced by the stratigraphic framework and the depositional system. Seismic sections and geophysical logs of two wells drilled in the SW portion of the mentioned basin above register regional stratigraphic surfaces representing maximum floods related to a transgressive event. The sequential analysis of 80 m of drill core (~450 m deep) recognized nine depositional facies with an upwards granodecrescent standard piling that limits cycles with an erosional conglomeratic base (lag) overlain by intercalations of medium to very fine sandstones showing cross bedding (channel, planar and low angled) and horizontal bedding (plane-parallel , wave and flaser). The top of the cycles is marked by the deposition of pelites and the development of paleosoils and lagoons. The correlation of genetically related facies reveals associations of channel fillings, crevasse, and flood plains deposited in a transgressive system. Detailed descriptions of seventy nine thin sections aided by MEV-EBSD/EDS, DRX and stable isotope analyses in sandstones revealed an arcosian composition and complex textural arrays with abundant smectite fringes continuously covering primary components, mechanically infiltrated cuticles and moldic and intragrain pores. K-feldspar epitaxial overgrowth covers microcline and orthoclase grains before any other phase. Abundant pseudomatrix due to the compactation of mud intraclasts concentrate along the stratification planes, locally replaced by macrocristalline calcite and microcrystalline and framboidal pyrite. Kaolinite (booklets and vermicular), microcrystalline smectite, microcrystalline titanium minerals and pyrite replace the primary components. The intergrain porosity prevails over the moldic, intragrain and contraction porosities. The pores are poorly connected due to the presence of intergranular smectite, k-feldspar overgrowth, infiltrated mud and pseudomatrix. The sandstones were subjected to eodiagenetic conditions next to the surface and shallow burial mesodiagenetic conditions. The diagenetic alterations reduced the porosity and the permeability mainly due to the precipitation of smectite fringes, compactation of mud intraclasts onto the pseudomatrix and cementing by poikilotopic calcite characterizing different reservoir petrofacies. These diagenetic products acted as barriers and detours to the flow of fluids thus reducing the quality of the reservoir.
Resumo:
The discussion about rift evolution in the Brazilian Equatorial margin during the South America-Africa breakup in the Jurassic/Cretaceous has been focused in many researches. But rift evolution based on development and growth of faults has not been well explored. In this sense, we investigated the Cretaceous Potiguar Basin in the Equatorial margin of Brazil to understand the geometry of major faults and the influence of crustal heterogeneity and preexisting structural fabric in the evolution of the basin internal architecture. Previous studies pointed out that the rift is an asymmetrical half-graben elongated along the NE-SW direction. We used 2D seismic, well logs and 3D gravity modeling to analyze four major border fault segments and determine their maximum displacement (Dmax) and length (L) ratio in the Potiguar Rift. We constrained the 3D gravity modeling with well data and the interpretation of seismic sections. The difference of the fault displacement measured in the gravity model is in the order of 10% compared to seismic and well data. The fault-growth curves allowed us to divide the faulted rift border into four main fault segments, which provide roughly similar Dmax/L ratios. Fault-growth curves suggest that a regional uniform tectonic mechanism influenced growth of the rift fault segments. The variation of the displacements along the fault segments indicates that the fault segments were formed independently during rift initiation and were linked by hard and soft linkages. The latter formed relay ramps. In the interconnection zones the Dmax/L ratios are highest due to interference of fault segment motions. We divided the evolution of the Potiguar Rift into five stages based on these ratios and correlated them with the major tectonic stages of the breakup between South America and Africa in Early Cretaceous.
Resumo:
The discussion about rift evolution in the Brazilian Equatorial margin during the South America-Africa breakup in the Jurassic/Cretaceous has been focused in many researches. But rift evolution based on development and growth of faults has not been well explored. In this sense, we investigated the Cretaceous Potiguar Basin in the Equatorial margin of Brazil to understand the geometry of major faults and the influence of crustal heterogeneity and preexisting structural fabric in the evolution of the basin internal architecture. Previous studies pointed out that the rift is an asymmetrical half-graben elongated along the NE-SW direction. We used 2D seismic, well logs and 3D gravity modeling to analyze four major border fault segments and determine their maximum displacement (Dmax) and length (L) ratio in the Potiguar Rift. We constrained the 3D gravity modeling with well data and the interpretation of seismic sections. The difference of the fault displacement measured in the gravity model is in the order of 10% compared to seismic and well data. The fault-growth curves allowed us to divide the faulted rift border into four main fault segments, which provide roughly similar Dmax/L ratios. Fault-growth curves suggest that a regional uniform tectonic mechanism influenced growth of the rift fault segments. The variation of the displacements along the fault segments indicates that the fault segments were formed independently during rift initiation and were linked by hard and soft linkages. The latter formed relay ramps. In the interconnection zones the Dmax/L ratios are highest due to interference of fault segment motions. We divided the evolution of the Potiguar Rift into five stages based on these ratios and correlated them with the major tectonic stages of the breakup between South America and Africa in Early Cretaceous.
Resumo:
The study area is within the Pirangi River Basin, eastern sector of Rio Grande do Norte state, where is located of the Parnamirim city. It has an area of approximately 370 km². Urbanization has developed much fast without an appropriate infrastructure, mainly by the lack of sewage systems, with risks of contamination of groundwater that may cause serious damage to the health of the population. The Barreiras Aquifer System groundwater in the area represents the main source of water supply for urban and rural populations. The use of groundwater occurs without adequate planning and therefore, important recharge areas are being occupied. This study was conducted to quantify the use and evaluation of the potential of groundwater, in order to increase good water quality supply and lower risks of being affected by polluting activities. With these objectives, the following activities were carried out: 268 points of water have been registered; characterization of the lithological, thickness and hydrogeological structure of the Barreiras aquifer, based on the correlation of well logs; and evaluation of hydrodynamic parameters of the aquifer, from the interpretation of results well pumping tests. It was found that the saturated thickness increases from west to east towards the sea, with values ranging from 15,47-56,5 m with an average of 32,45 m. The hydrodynamic parameters using Cooper-Jacob method were: average transmissivity of 5,9x10-3 m²/s and average hydraulic conductivity 2,82x10-4 m/s. The effective porosity is of 15%, obtained by applying Biecinski equation. The potentiometric map shows the main direction of groundwater flow, from west to east, and identifies the recharge areas corresponding to the region of the tablelands of the "Barreiras". The river valleys refer to the discharge areas of the aquifer system. The Recharge was estimated at 253 mm/year, which corresponds to the 16.4% rate of infiltration.
Resumo:
The study area is within the Pirangi River Basin, eastern sector of Rio Grande do Norte state, where is located of the Parnamirim city. It has an area of approximately 370 km². Urbanization has developed much fast without an appropriate infrastructure, mainly by the lack of sewage systems, with risks of contamination of groundwater that may cause serious damage to the health of the population. The Barreiras Aquifer System groundwater in the area represents the main source of water supply for urban and rural populations. The use of groundwater occurs without adequate planning and therefore, important recharge areas are being occupied. This study was conducted to quantify the use and evaluation of the potential of groundwater, in order to increase good water quality supply and lower risks of being affected by polluting activities. With these objectives, the following activities were carried out: 268 points of water have been registered; characterization of the lithological, thickness and hydrogeological structure of the Barreiras aquifer, based on the correlation of well logs; and evaluation of hydrodynamic parameters of the aquifer, from the interpretation of results well pumping tests. It was found that the saturated thickness increases from west to east towards the sea, with values ranging from 15,47-56,5 m with an average of 32,45 m. The hydrodynamic parameters using Cooper-Jacob method were: average transmissivity of 5,9x10-3 m²/s and average hydraulic conductivity 2,82x10-4 m/s. The effective porosity is of 15%, obtained by applying Biecinski equation. The potentiometric map shows the main direction of groundwater flow, from west to east, and identifies the recharge areas corresponding to the region of the tablelands of the "Barreiras". The river valleys refer to the discharge areas of the aquifer system. The Recharge was estimated at 253 mm/year, which corresponds to the 16.4% rate of infiltration.
Resumo:
The Middle Devonian-Early Carboniferous sequence of the Parnaíba Basin, lithostratigraphically defined as Canindé Group, has been reinterpreted using the basic model of sequence stratigraphy. Therefore, lithology and gamma ray well-logs and seismic lines of central portion of the basin were analyzed, producing up from there diagrams 1D, isochore maps and stratigraphic sections. As results of this study, were defined two depositional cycles of second order, referred as Depositional Sequence 1 (SEQ1) and the Depositional Sequence 2 (SEQ2). The SEQ1, with interval about 37 Ma, is limited below by Early Devonian Unconformity and is equivalent to the formations Itaim, Pimenteiras and Cabeças. The SEQ2, which follows, comprises a range of about 15 Ma and is equivalent to the Longá Formation The SEQ1 starts with the lowstand systems tract, consisting of progradational parasequence set in the basal part, predominantly pelitic, deposited on a prodelta under influence of storms and the upper part consists in sandstones of deltaic front, with the maximum regressive surface on the upper limit. The transgressive systems tract, deposited above, is characterized by retrogradacional parasequence set composed of shallow shelf mudstones, deposited under storm conditions. The maximum flooding surface, upper limit of this tract, is positioned in a shale level whose radioactivity in gammaray well-log is close to 150 API. The highstand systems tract presents progradational parasequence set, comprising mudstones and sandstones deposited in shelf, fluvial-estuarine or deltaic and periglacial environments, with the upper limit the Late Devonian Unconformity. The SEQ2 was deposited in shelf environment, starting with the lowstand systems tract, that is characterized by a progradational parasequence set, followed by the transgressive systems tract, with retrogradational character. The upper limit of the tract corresponding to the fusion between maximum flooding surface with the upper limit of this sequence, which is the Early Carboniferous Unconformity, where the overlapping section was eroded. This section, which corresponds the highstand systems tract is restricted to portions at which the erosion that generate the Early-Carboniferous Unconformity was less effective, preserving the records of this unit.
Resumo:
The Middle Devonian-Early Carboniferous sequence of the Parnaíba Basin, lithostratigraphically defined as Canindé Group, has been reinterpreted using the basic model of sequence stratigraphy. Therefore, lithology and gamma ray well-logs and seismic lines of central portion of the basin were analyzed, producing up from there diagrams 1D, isochore maps and stratigraphic sections. As results of this study, were defined two depositional cycles of second order, referred as Depositional Sequence 1 (SEQ1) and the Depositional Sequence 2 (SEQ2). The SEQ1, with interval about 37 Ma, is limited below by Early Devonian Unconformity and is equivalent to the formations Itaim, Pimenteiras and Cabeças. The SEQ2, which follows, comprises a range of about 15 Ma and is equivalent to the Longá Formation The SEQ1 starts with the lowstand systems tract, consisting of progradational parasequence set in the basal part, predominantly pelitic, deposited on a prodelta under influence of storms and the upper part consists in sandstones of deltaic front, with the maximum regressive surface on the upper limit. The transgressive systems tract, deposited above, is characterized by retrogradacional parasequence set composed of shallow shelf mudstones, deposited under storm conditions. The maximum flooding surface, upper limit of this tract, is positioned in a shale level whose radioactivity in gammaray well-log is close to 150 API. The highstand systems tract presents progradational parasequence set, comprising mudstones and sandstones deposited in shelf, fluvial-estuarine or deltaic and periglacial environments, with the upper limit the Late Devonian Unconformity. The SEQ2 was deposited in shelf environment, starting with the lowstand systems tract, that is characterized by a progradational parasequence set, followed by the transgressive systems tract, with retrogradational character. The upper limit of the tract corresponding to the fusion between maximum flooding surface with the upper limit of this sequence, which is the Early Carboniferous Unconformity, where the overlapping section was eroded. This section, which corresponds the highstand systems tract is restricted to portions at which the erosion that generate the Early-Carboniferous Unconformity was less effective, preserving the records of this unit.
Resumo:
Under the framework of the ANDRILL Southern McMurdo Sound (SMS) Project successful downhole experiments were conducted in the 1138.54 metre (m)-deep AND-2A borehole. Wireline logs successfully recorded were: magnetic susceptibility, spectral gamma ray, sonic velocity, borehole televiewer, neutron porosity, density, calliper, geochemistry, temperature and dipmeter. A resistivity tool and its backup both failed to operate, thus resistivity data were not collected. Due to hole conditions, logs were collected in several passes from the total depth at ~1138 metres below sea floor (mbsf) to ~230 mbsf, except for some intervals that were either inaccessible due to bridging or were shielded by the drill string. Furthermore, a Vertical Seismic Profile (VSP) was created from ~1000 mbsf up to the sea floor. The first hydraulic fracturing stress measurements in Antarctica were conducted in the interval 1000-1138 mbsf. This extensive data set will allow the SMS Science Team to reach some of the ambitious objectives of the SMS Project. Valuable contributions can be expected for the following topics: cyclicity and climate change, heat flux and fluid flow, seismic stratigraphy in the Victoria Land Basin, and structure and state of the modern crustal stress field.
Resumo:
The cores described in this report were taken on JAPANYON Expedition in June-September 1961 by Scripps Institution of Oceanography from, the R/V Spencer F. Baird. A total of 85 cores and dredges were recovered and are available at Scripps for sampling and study. The coring sites are all in the eastern tropical central Pacific.
Resumo:
The cores and dredges described in this report were taken on the HILO Expedition in March-April 1962 by Scripps Institution of Oceanography from, the R/V Stranger. A total of 21 cores and dredges were recovered and are available at Scripps for sampling and study.
Resumo:
The aim of this thesis was to investigate the high prevalence of Clostridium difficile in patients with cystic fibrosis (CF), and to control its dissemination. To determine the carriage rate of C. difficile in CF patients, 60 patients were tested for C. difficile and its toxin. In total, 50% of patients were found to be asymptomatic carriers of C. difficile despite toxin being detected in 31.66% of patients. Ribotyping of the C. difficile isolates revealed 16 distinct ribotypes, including the hyper virulent RT078. All isolates were sensitive to both Vancomycin and Metronidazole. The effect of CF and its treatment on the gut microbiota of CF patients was assessed by 16s sequencing of the gut microbiota of 68 CF patients. When compared to a healthy control group, CF patient gut microbiota was found to be less diverse and had an increased Firmicutes to Bacteriodetes ratio. Interestingly, CF patients who were carriers of C. difficile had a less diverse gut microbiota than C. difficile negative CF patients. Multilocus sequence typing was found to be comparable to PCR-ribotyping for typing C. difficile isolates from high risk patient groups. The sequence type ST 26 is potentially associated with CF patients as all seven isolates were found in this group and this sequence type has been previously reported in CF patients in a geographically distinct study. The bacteriophage ФCD6356 was assessed as a targeted antimicrobial against C. difficile in an ex-vivo model of the human distal colon. Despite reducing viable C. difficile by 1.75 logs over 24 hours, this bacteriophage was not suitable due to its lysogenic nature. Following treatment, all surviving C. difficile were immune to reinfection due to prophage integration. However, the ФCD6356 encoded endolysin was capable of reducing viable C. difficile by 2.9 over 2 hours in vitro after being cloned and expressed in Escherichia coli.
Resumo:
A spring 2016 report about public computer usage on the first floor of Perkins and Bostock libraries. This report includes data from survey questions, an observational study, and transaction logs. The report also includes recommendations for changes based on the data collected.