Polymer controlled mineralization of zinc phosphate hydrates and applications in corrosion protection, catalysis and biomedicine

ZUSAMMENFASSUNG Die Tauglichkeit von Hybridmaterialien auf der Basis von Zinkphosphathydrat-Zementen zum Einsatz als korrosionshemmende anorganische Pigmente oder zur prothetischen und konservierenden Knochen- und Zahntherapie wird weltweit empirisch seit den neunziger Jahren intensiv erforscht. In der vorliegenden Arbeit wurden zuerst Referenzproben, d.h. alpha-und beta-Hopeite (Abk. a-,b-ZPT) dank eines hydrothermalen Kristallisationsverfahrens in wässerigem Milieu bei 20°C und 90°C hergestellt. Die Kristallstruktur beider Polymorphe des Zinkphosphattetrahydrats Zn3(PO4)2  4 H2O wurde komplett bestimmt. Einkristall-strukturanalyse zeigt, daß der Hauptunterschied zwischen der alpha-und beta-Form des Zinkphosphattetrahydrats in zwei verschiedenen Anordnungen der Wasserstoffbrücken liegt. Die entsprechenden drei- und zweidimensionalen Anordnungen der Wasserstoffbrücken der a-und b-ZPT induzieren jeweils unterschiedliches thermisches Verhalten beim Aufwärmen. Während die alpha-Form ihr Kristallwasser in zwei definierten Stufen verliert, erzeugt die beta-Form instabile Dehydratationsprodukt. Dieses entspricht zwei unabhängigen, aber nebeneinander ablaufenden Dehydratationsmechanismen: (i) bei niedrigen Heizraten einen zweidimensionalen Johnson-Mehl-Avrami (JMA) Mechanismus auf der (011) Ebene, der einerseits bevorzugt an Kristallkanten stattfindet und anderseits von existierenden Kristalldefekten auf Oberflächen gesteuert wird; (ii) bei hohen Heizraten einem zweidimensionalen Diffusionsmechanismus (D2), der zuerst auf der (101) Ebene und dann auf der (110) Ebene erfolgt. Durch die Betrachtung der ZPT Dehydratation als irreversibele heterogene Festkörperstufenreaktion wurde dank eines „ähnlichen Endprodukt“-Protokolls das Dehydratationsphasendiagramm aufgestellt. Es beschreibt die möglichen Zusammenhänge zwischen den verschiedenen Hydratationszuständen und weist auf die Existenz eines Übergangszustandes um 170°C (d.h. Reaktion b-ZPT  a-ZPT) hin. Daneben wurde auch ein gezieltes chemisches Ätzverfahren mit verdünnten H3PO4- und NH3 Lösungen angewendet, um die ersten Stufe des Herauslösens von Zinkphosphat genau zu untersuchen. Allerdings zeigen alpha- und beta-Hopeite charakteristische hexagonale und kubische Ätzgruben, die sich unter kristallographischer Kontrolle verbreitern. Eine zuverlässige Beschreibung der Oberfächenchemie und Topologie konnte nur durch AFM und FFM Experimente erfolgen. Gleichzeitig konnte in dieser Weise die Oberflächendefektdichte und-verteilung und die Volumenauflösungsrate von a-ZPT und b-ZPT bestimmt werden. Auf einem zweiten Weg wurde eine innovative Strategie zur Herstellung von basischen Zinkphosphatpigmenten erster und zweiter Generation (d.h. NaZnPO4  1H2O und Na2ZnPO4(OH)  2H2O) mit dem Einsatz von einerseits oberflächenmodifizierten Polystyrolatices (z.B. produziert durch ein Miniemulsionspolymerisationsverfahren) und anderseits von Dendrimeren auf der Basis von Polyamidoamid (PAMAM) beschritten. Die erhaltene Zeolithstruktur (ZPO) hat in Abhängigkeit von steigendem Natrium und Wassergehalt unterschiedliche kontrollierte Morphologie: hexagonal, würfelförmig, herzförmig, sechsarmige Sterne, lanzettenförmige Dendrite, usw. Zur quantitativen Evaluierung des Polymereinbaus in der Kristallstruktur wurden carboxylierte fluoreszenzmarkierte Latices eingesetzt. Es zeigt sich, daß Polymeradditive nicht nur das Wachstum bis zu 8 µm.min-1 reduzierten. Trotzdem scheint es auch als starker Nukleationsbeschleuniger zu wirken. Dank der Koordinationschemie (d.h. Bildung eines sechszentrigen Komplexes L-COO-Zn-PO4*H2O mit Ligandenaustausch) konnten zwei einfache Mechanismen zur Wirkung von Latexpartikeln bei der ZPO Kristallisation aufgezeigt werden: (i) ein Intrakorona- und (ii) ein Extrakorona-Keimbildungsmechanismus. Weiterhin wurde die Effizienz eines Kurzzeit- und Langzeitkorrosionschutzes durch maßgeschneiderte ZPO/ZPT Pigmente und kontrollierte Freisetzung von Phosphationen in zwei Näherungen des Auslösungsgleichgewichts abgeschätzt: (i) durch eine Auswaschungs-methode (thermodynamischer Prozess) und (ii) durch eine pH-Impulsmethode (kinetischer Prozess. Besonders deutlich wird der Ausflösungs-Fällungsmechanismus (d.h. der Metamorphismus). Die wesentliche Rolle den Natriumionen bei der Korrosionshemmung wird durch ein passendes zusammensetzungsabhängiges Auflösungsmodell (ZAAM) beschrieben, das mit dem Befund des Salzsprühteste und der Feuchtigkeitskammertests konsistent ist. Schließlich zeigt diese Arbeit das herausragende Potential funktionalisierter Latices (Polymer) bei der kontrollierten Mineralisation zur Herstellung maßgeschneiderter Zinkphosphat Materialien. Solche Hybridmaterialien werden dringend in der Entwicklung umweltfreundlicher Korrosionsschutzpigmente sowie in der Dentalmedizin benötigt.

Preparation and study of magnetic thin film based sub-micron structures

Due to its high Curie temperature of 420K and band structure calculations predicting 100% spin polarisation, Sr2FeMoO6 is a potential candidate for spintronic devices. However, the preparation of good quality thin films has proven to be a non-trivial task. Epitaxial Sr2FeMoO6 thin films were prepared by pulsed laser deposition on different substrates. Differing from previous reports a post-deposition annealing step at low oxygen partial pressure (10-5 mbar) was introduced and enabled the fabrication of reproducible, high quality samples. According to the structural properties of the substrates the crystal structure and morphology of the thin films are modified. The close interrelation between the structural, magnetic and electronic properties of Sr2FeMoO6 was studied. A detailed evaluation of the results allowed to extract valuable information on the microscopic nature of magnetism and charge transport. Smooth films with a mean roughness of about 2 nm have been achieved, which is a pre-requisite for a possible inclusion of this material in future devices. In order to establish device-oriented sub-micron patterning as a standard technique, electron beam lithography and focussed ion beam etching facilities have been put into operation. A detailed characterisation of these systems has been performed. To determine the technological prospects of new spintronics materials, the verification of a high spin polarisation is of vital interest. A popular technique for this task is point contact Andreev reflection (PCAR). Commonly, the charge transport in a transparent metal-superconductor contact of nanometer dimensions is attributed solely to coherent transport. If this condition is not fulfilled, inelastic processes in the constriction have to be considered. PCAR has been applied to Sr2FeMoO6 and the Heusler compound Co2Cr0.6Fe0.4Al. Systematic deviations between measured spectra and the standard models of PCAR have been observed. Therefore existing approaches have been generalised, in order to include the influence of heating. With the extended model the measured data was successfully reproduced but the analysis has revealed grave implications for the determination of spin polarisation, which was found to break down completely in certain cases.

Plasmonenresonanzen von sichelförmigen metallischen Nanoobjekten

Metallische Objekte in der Größenordnung der optischen Wellenlänge zeigen Resonanzen im optischen Spektralbereich. Mit einer Kombination aus Kolloidlithographie, Metallfilmbedampfung und reaktivem Ionenstrahl¨atzen wurden Nanosicheln aus Gold bzw. Silber mit identischer Form und Orientierung in Sichelform mit einer Größe von 60nm bis 400nm hergestellt. Der Öffnungswinkel der Nanosicheln lässt sich kontinuierlich einstellen. Durch die einheitliche Orientierung lassen sich Messungen am Ensemble direkt auf das Verhalten des Einzelobjektes übertragen, wie ein Vergleich der Extinktionsspektren einer Ensemblemessung am UV/Vis/NIR-Spektrometer mit einer Einzelpartikelmessung in einem konfokalen Mikroskop zeigt. Die optische Antwort der Nanosicheln wurde als zwei-dimensionales Modell mit einer Finite Elemente Methode berechnet. Das Ergebnis sind mehrere polarisationsabhängige Resonanzen im optischen Spektrum. Diese lassen sich durch Variation des Öffnungswinkels und der Gr¨oße der Nanosichel verschieben. Durch Beleuchten lassen sich plasmonische Schwingungen anregen, die ein stark lokalisiertes Nahfeld an den Spitzen und in der Öffnung der Nanosicheln erzeugen. Das Nahfeld der Partikelresonanz wurde mit einer Fotolackmethode nachgewiesen. Die Untersuchungen am UV/Vis/NIR-Spektrometer zeigen mehrere polarisationsabhängige Resonanzen im Spektralbereich von 300 nm bis 3200 nm. Die Resonanzen der Nanosicheln lassen sich durch den Öffnungswinkel und den Durchmesser in der Größenordnung der Halbwertbreite im optischen Spektrum verschieben. In der Anwendung als Chemo- bzw. Biosensor zeigen Gold-Nanosicheln eine ähnliche Empfindlichkeit wie vergleichbare Sensoren auf der Basis von dünnen Metallstrukturen. Das Nahfeld zeichnet sich durch eine starke Lokalisierung aus und dringt, je nach Multipolordnung, zwischen 14 nm und 70 nm in die Umgebung ein. Quantenpunkte wurden an das Nahfeld der Nanosicheln gekoppelt. Die Emission der Quantenpunkte bei einer Wellenlänge von 860nm wird durch die Resonanz der Nanosicheln verstärkt. Die Nanosicheln wurden als optische Pinzette eingesetzt. Bei einer Anregung mit einem Laser bei einer Wellenlänge von 1064 nm wurden Polystyrolkolloide mit einem Durchmesser von 40 nm von den resonanten Nanosicheln eingefangen. Die Nanosicheln zeigen außergewöhnliche optische Eigenschaften, die mithilfe der Geometrieparameter über einen großen Bereich verändert werden können. Die ersten Anwendungen haben Anknüpfungspunkte zur Verwendung in der Sensorik, Fluoreszenzspektroskopie und als optische Pinzette aufgezeigt.

Multiscale fabrication of functional materials for life sciences

Regenerative medicine claims for a better understanding of the cause-effect relation between cell behaviour and environment signals. The latter encompasses topographical, chemical and mechanical stimuli, electromagnetic fields, gradients of chemo-attractants and haptotaxis. In this perspective, a spatial control of the structures composing the environment is required. In this thesis I describe a novel approach for the multiscale patterning of biocompatible functional materials in order to provide systems able to accurately control cell adhesion and proliferation. The behaviour of different neural cell lines in response to several stimuli, specifically chemical, topographical and electrical gradients is presented. For each of the three kind of signals, I chose properly tailored materials and fabrication and characterization techniques. After a brief introduction on the state of art of nanotechnology, nanofabrication techniques and regenerative medicine in Chapter 1 and a detailed description of the main fabrication and characterization techniques employed in this work in Chapter 2, in Chapter 3 an easy route to obtain accurate control over cell proliferation close to 100% is described (chemical control). In Chapter 4 (topographical control) it is shown how the multiscale patterning of a well-established biocompatible material as titanium dioxide provides a versatile and robust method to study the effect of local topography on cell adhesion and growth. The third signal, viz. electric field, is investigated in Chapter 5 (electrical control), where the very early stages of neural cell adhesion are studied in the presence of modest steady electric fields. In Chapter 6 (appendix) a new patterning technique, called Lithographically Controlled Etching (LCE), is proposed. It is shown how LCE can provide at the same time the micro/nanostructuring and functionalization of a surface with nanosized objects, thus being suitable for applications both in regenerative medicine in biosensing.

Synthese und Charakterisierung von Oxidchalkogeniden und Bronzen für die Nanostrukturierung

Ausgehend von der Entdeckung der reversiblen Strukturierung mittels Rastersondenmethoden im Phasensystem Na2O/V2O5/P2O5 wurden im Rahmen dieser Arbeit zwei Ansatzpunkte verfolgt. Einerseits sollten mittels der Schmelzflußelektrolyse einige bereits existierende niederdimensionale Molybdänbronzen mit bekannten elektronischen Übergängen in ausreichend großen Kristallen gezüchtet werden, um sie auf ihre Strukturierungseigenschaften hin zu untersuchen. Gleichzeitig sollte durch Variation versucht werden, neue, bisher unbekannte Bronzen oder reduzierte Oxide zu synthetisieren und charakterisieren. Der zweite Schwerpunkt dieser Arbeit lag in der Synthese und Charakterisierung von Oxidchalkogeniden, bestehend aus einem Seltenerdmetall und einem 3d-Metall von Titan bis hin zu den mittleren Übergangsmetallen. Diese Verbindungen können durch die Kombination der jeweiligen Eigenschaften der oxidischen und chalkogeniden Teilstrukturen völlig neue elektronische und/oder magnetische Eigenschaften aufweisen. Mögliche auftretende Phasenübergänge sind wiederum für Strukturierungsversuche interessant. Die zu den Oxidchalkogeniden durchgeführten Untersuchungen ergaben im Phasensystem Ln/Ti/S/O (Ln = Lanthanoide) insgesamt sechs Verbindungen. Zwei von ihnen, La8Ti9S24O4 und Nd20Ti11S44O6, besitzen als gemeinsames Strukturelement tetranukleare [Ti4(u4-S)2(u2-O)4]-Cluster, bestehend aus vier miteinander über gemeinsame Flächen kondensierte TiS4O2-Oktaeder. Die Titanpositionen innerhalb der Cluster sind mit Ti+3-Ionen besetzt. Beide Verbindungen weisen in einem Temperaturbereich zwischen 150 K und 250 K eine deutlich ausgeprägte Hysterese der magnetischen Suszeptibilität auf, die sich im Falle von La8Ti9S24O4 auf einen Jahn-Teller-Übergang zurückführen läßt. Daneben konnte erstmals eine Serie oxidisch/sulfidisch gemischter Ruddlesden-Popper-Verbindungen mit Ln2Ti2S2O5 (Ln = Pr, Nd, Sm) synthetisiert und charakterisiert werden. Titan liegt als vierwertiges Ion in aus TiSO5-Oktaedern gebildeten Perowskit-Doppelschichten vor. Die neunfach koordinierten Positionen sind mit den Seltenerdmetallionen gefüllt, die zwölffach koordinierten Lagen sind unbesetzt. Bei dem sechsten erhaltene Titanoxidsulfid, La4TiS6.5O1.5, handelt es sich um einen Halbleiter mit einer Bandlücke von etwa 2 eV. Weiterhin gelang es, die Serie Ln2M3S2O8 (Ln = La, Ce, Pr, Nd, Sm; M = Nb, Ta) zu synthetisieren und in ihren physikalischen Eigenschaften zu charakterisieren. Es handelt sich ausnahmslos um Halbleiter mit Bandlücken zwischen E=0.125 eV für La2Nb3S2O8 und E=0.222 eV für Pr2Ta3S2O8. Die Struktur der Oxidsulfide Ce2Ta3S2O8, Pr2Ta3S2O8, Nd2Nb3S2O8 sowie Sm2Ta3S2O8 weist im Gegensatz zu den anderen Verbindungen eine Fehlordnung eines der beiden kristallographisch unabhängigen Nb- bzw. Ta-Atome auf. Daraus resultiert eine Symmetrieerniedrigung von Pnma zu Pbam. Der Einsatz von Europium führte zu einer neuen Modifikation des bronzoiden Oxids EuTa2O6, in der das Europium als Eu+2 vorliegt, wie 151Eu-Mößbauer-Untersuchungen bestätigten. Vor der Durchführung der Kristallzüchtungen mittels der Schmelzflußelektrolysen mußten die benutzen Öfen und Elektrolysezellen geplant und angefertigt werden. Es konnten dann verschiedene blaue, rote und violette Moybdänbronzen (sowie La2Mo2O7) in Kristallen bis zu 25 mm Länge dargestellt werden. Ferner gelang die erste exakte Einkristalluntersuchung der roten Bronze Rb0.33MoO3. Sie verfügt über die höchste d-Elektronen-Lokalisierungsrate aller bekannten roten Bronzen. Die erhaltenen Bronzen wurden teilweise von der Arbeitsgruppe Fuchs, Physikalisches Institut der Westfälischen Wilhelms-Universität Münster, auf ihre Nanostrukturierbarkeit hin untersucht. Dabei ergaben sich zwei verschiedene Strukturierungsmechanismen. Sind es im Fall der blauen Alkalimetall-Molybdänbronzen ausschließlich Lochstrukturen, die entstehen, handelt es sich bei La2Mo2O7 um Hügelstrukturen. Mittels der Schmelzflußelektrolyse konnte auch das gemischtvalente Alkalimetall-Eisenmolybdat NaFe2(MoO4)3 synthetisiert werden. Daneben gelang die Synthese dreier weiterer Alkalimetall-Eisenmolybdate: Cs2Fe2(MoO4)3, NaFe4(MoO4)5 und CsFe5(MoO4)7. Bis auf Cs2Fe2(MoO4)3, welches in der bekannten Langbeinit-Struktur kristallisiert, handelt es sich bei den übrigen Alkalimetall-Eisenmolybdaten um völlig neuartige Käfigverbindungen, bzw. bei CsFe5(MoO4)7 um eine Tunnelverbindung. Die Kristallstrukturen beinhalten kondensierte FeO6-Oktaeder. Im Fall von NaFe2(MoO4)3 lassen sich [Fe2O10]-Einheiten, für NaFe4(MoO4)5 [Fe2O10]- sowie [Fe3O14]-Einheiten, und für CsFe5(MoO4)7 [Fe4O18]-Baueinheiten beobachten. Die Positionen der Fe+2- und Fe+3-Atome in NaFe4(MoO4)5 wurden mit Hilfe einer 57Fe-Mößbauer-Untersuchung bestimmt.

Noble-metal nanoparticles produced with colloidal lithography: fabrication, optical properties and applications

In this work, metal nanoparticles produced by nanosphere lithography were studied in terms of their optical properties (in connection to their plasmon resonances), their potential application in sensing platforms - for thin layer sensing and bio-recognition events -, and for a particular case (the nanocrescents), for enhanced spectroscopy studies. The general preparation procedures introduced early in 2005 by Shumaker-Parry et al. to produce metallic nanocrescents were extended to give rise to more complex (isolated) structures, and also, by combining colloidal monolayer fabrication and plasma etching techniques, to arrays of them. The fabrication methods presented in this work were extended not only to new shapes or arrangements of particles, but included also a targeted surface tailoring of the substrates and the structures, using different thiol and silane compounds as linkers for further attachment of, i.e. polyelectrolyte layers, which allow for a controlled tailoring of their nanoenvironment. The optical properties of the nanocrescents were studied with conventional transmission spectroscopy; a simple multipole model was adapted to explain their behaviour qualitatively. In terms of applications, the results on thin film sensing using these particles show that the crescents present an interesting mode-dependent sensitivity and spatial extension. Parallel to this, the penetrations depths were modeled with two simplified schemes, obtaining good agreement with theory. The multiple modes of the particles with their characteristic decay lengths and sensitivities represent a major improvement for particle-sensing platforms compared to previous single resonance systems. The nanocrescents were also used to alter the emission properties of fluorophores placed close to them. In this work, green emitting dyes were placed at controlled distances from the structures and excited using a pulsed laser emitting in the near infrared. The fluorescence signal obtained in this manner should be connected to a two-photon processes triggered by these structures; obtaining first insight into plasmon-mediated enhancement phenomena. An even simpler and faster approach to produce plasmonic structures than that for the crescents was tested. Metallic nanodiscs and nanoellipses were produced by means of nanosphere lithography, extending a procedure reported in the literature to new shapes and optical properties. The optical properties of these particles were characterized by extinction spectroscopy and compared to results from the literature. Their major advantage is that they present a polarization-dependent response, like the nanocrescents, but are much simpler to fabricate, and the resonances can be tailored in the visible with relative ease. The sensing capabilities of the metallic nanodiscs were explored in the same manner as for the nanocrescents, meaning their response to thin layers and to bio-recognition events on their surface. The sensitivity of these nanostructures to thin films proved to be lower than that of the crescents, though in the same order of magnitude. Experimental information about the near field extension for the Au nanodiscs of different sizes was also extracted from these measurements. Further resonance-tailoring approaches based on electrochemical deposition of metals on the nanodiscs were explored, as a means of modifying plasmon resonances by changing surface properties of the nanoparticles. First results on these experiments would indicate that the deposition of Ag on Au on a submonolayer coverage level can lead to important blue-shifts in the resonances, which would open a simple way to tailor resonances by changing material properties in a local manner.

Caratterizzazione della superficie di array di nanofili di silicio

Nel primo capitolo viene introdotto lo studio eff�ettuato e descritto un metodo di misure successivo alla caratterizzazione della super�ficie. Nel secondo capitolo vengono descritti i campioni analizzati e, nello speci�fico, la crescita attraverso MaCE dei nanofi�li di silicio. Nel terzo capitolo viene descritto lo strumento AFM utilizzato e la teoria della caratterizzazione alla base dello studio condotto. Nella quarta sezione vengono descritti i risultati ottenuti mentre nelle conclusioni viene tratto il risultato dei valori ottenuti di RMS roughness e roughness exponent.

Fabrication, Electrical Characterization and Simulation of Thin Film Solar Cells: CdTe and CIGS Materials

CdTe and Cu(In,Ga)Se2 (CIGS) thin film solar cells are fabricated, electrically characterized and modelled in this thesis. We start from the fabrication of CdTe thin film devices where the R.F. magnetron sputtering system is used to deposit the CdS/CdTe based solar cells. The chlorine post-growth treatment is modified in order to uniformly cover the cell surface and reduce the probability of pinholes and shunting pathways creation which, in turn, reduces the series resistance. The deionized water etching is proposed, for the first time, as the simplest solution to optimize the effect of shunt resistance, stability and metal-semiconductor inter-diffusion at the back contact. In continue, oxygen incorporation is proposed while CdTe layer deposition. This technique has been rarely examined through R.F sputtering deposition of such devices. The above experiments are characterized electrically and optically by current-voltage characterization, scanning electron microscopy, x-ray diffraction and optical spectroscopy. Furthermore, for the first time, the degradation rate of CdTe devices over time is numerically simulated through AMPS and SCAPS simulators. It is proposed that the instability of electrical parameters is coupled with the material properties and external stresses (bias, temperature and illumination). Then, CIGS materials are simulated and characterized by several techniques such as surface photovoltage spectroscopy is used (as a novel idea) to extract the band gap of graded band gap CIGS layers, surface or bulk defect states. The surface roughness is scanned by atomic force microscopy on nanometre scale to obtain the surface topography of the film. The modified equivalent circuits are proposed and the band gap graded profiles are simulated by AMPS simulator and several graded profiles are examined in order to optimize their thickness, grading strength and electrical parameters. Furthermore, the transport mechanisms and Auger generation phenomenon are modelled in CIGS devices.

Studio degli effetti della mordenzatura con acido fluoridrico sul disilicato di litio utilizzato in odontoiatria

Scopo dello studio: valutare i cambiamenti indotti da diversi trattamenti di mordenzatura sulla morfologia superficiale e sulla microstruttura di due vetro-ceramiche a base disilicato di litio (IPS e.max® Press e IPS e.max® CAD) ed esaminarne gli effetti sia sull’adesione con un cemento resinoso che sulla resistenza alla flessione. Materiali e metodi: Settanta dischetti (12 mm di diametro, 2 mm di spessore) di ogni ceramica sono stati preparati e divisi in 5 gruppi: nessun trattamento (G1), HF 5% 20s (G2), HF 5% 60s (G3), HF 9.6% 20s (G4), HF 9.6% 60s (G5). Un campione per ogni gruppo è stato analizzato mediante profilometro ottico e osservato al SEM. Per gli altri campioni è stato determinato lo shear bond strength (SBS) con un cemento resinoso. Dopo l’SBS test, i campioni sono stati caricati fino a frattura utilizzando il piston-on-three-ball test per determinarne la resistenza biassiale alla flessione. Risultati: L’analisi morfologica e microstrutturale dei campioni ha rivelato come diversi trattamenti di mordenzatura producano delle modifiche nella rugosità superficiale che non sono direttamente collegate ad un aumento dei valori di adesione e dei cambiamenti microstrutturali che sono più rilevanti con l’aumento del tempo di mordenzatura e di concentrazione dell’acido. I valori medi di adesione (MPa) per IPS e.max® CAD sono significativamente più alti in G2 e G3 (21,28 +/- 4,9 e 19,55 +/- 5,41 rispettivamente); per IPS e.max® Press, i valori più elevati sono in G3 (16,80 +/- 3,96). La resistenza biassiale alla flessione media (MPa) è più alta in IPS e.max® CAD (695 +/- 161) che in IPS e.max® Press (588 +/- 117), ma non è non influenzata dalla mordenzatura con HF. Conclusioni: il disilicato di litio va mordenzato preferibilmente con HF al 5%. La mordenzatura produce alcuni cambiamenti superficiali e microstrutturali nel materiale, ma tali cambiamenti non ne influenzano la resistenza in flessione.

Template-assisted patterning of functional polymers

In this thesis, anodic aluminum oxide (AAO) membranes, which provide well-aligned uniform mesoscopic pores with adjustable pore parameters, were fabricated and successfully utilized as templates for the fabrication of functional organic nanowires, nanorods and the respective well-ordered arrays. The template-assisted patterning technique was successfully applied for the realization of different objectives:rnHigh-density and well-ordered arrays of hole-conducting nanorods composed of cross-linked triphenylamine (TPA) and tetraphenylbenzidine (TPD) derivatives on conductive substrates like ITO/glass have been successfully fabricated. By applying a freeze-drying technique to remove the aqueous medium after the wet-chemical etching of the template, aggregation and collapsing of the rods was prevented and macroscopic areas of perfectly freestanding nanorods were feasible. Based on the hole-conducting nanorod arrays and their subsequent embedding into an electron-conducting polymer matrix via spin-coating, a novel routine concept for the fabrication of well-ordered all-organic bulk heterojunction for organic photovoltaic applications was successfully demonstrated. The increased donor/acceptor interface of the fabricated devices resulted in a remarkable increase of the photoluminescence quenching compared to a planar bilayer morphology. Further, the fundamental working principle of the templating approach for the solution-based all-organic photovoltaic device was demonstrated for the first time.rnFurthermore, in order to broaden the applicability of patterned surfaces, which are feasible via the template-based patterning of functional materials, AAO with hierarchically branched pores were fabricated and utilized as templates. By pursuing the common templating process hierarchically polymeric replicas, which show remarkable similarities with interesting biostructures, like the surface of the lotus leaf and the feet of a gecko, were successfully prepared.rnIn contrast to the direct infiltration of organic functional materials, a novel route for the fabrication of functional nanowires via post-modification of reactive nanowires was established. Therefore, reactive nanowires based on cross-linked pentafluorophenylesters were fabricated by utilizing AAO templates. The post-modification with fluorescent dyes was demonstrated. Furthermore, reactive wires were converted into well-dispersed poly(N-isopropylacrylamide) (PNIPAM) hydrogels, which exhibit a thermal-responsive reversible phase transition. The reversible thermal-responsible swelling of the PNIPAM nanowires exhibited a more than 50 % extended length than in the collapsed PNIPAM state. rnLast but not least, the shape-anisotropic pores of AAO were utilized to uniformly align the mesogens of a nematic liquid crystalline elastomer. Liquid crystalline nanowires with a narrow size distribution and uniform orientation of the liquid crystalline material were fabricated. It was shown that during the transition from the nematic to the isotropic phase the rod’s length shortened by roughly 40 percent. As such these liquid crystalline elastomeric nanowires may find application, as wire-shaped nanoactuators in various fields of research, like lab-on-chip systems, micro fluidics and biomimetics.rn

Integrazione tecnologica di grafene cresciuto per deposizione chimica da fase vapore per applicazioni termiche e termoelettriche

L’obiettivo del lavoro di tesi è quello di studiare l’integrazione del grafene con i processi tecnologici propri della tecnologia del silicio, per la realizzazione di dispositivi innovativi per la misura delle proprietà termiche e termoelettriche del grafene che sono tra le meno studiate ad oggi. L’attività sperimentale svolta, ha riguardato l’intero processo di produzione, processing ed integrazione tecnologica del grafene. Da una parte è stato messo a punto un processo ottimizzato, partendo da una approfondita ricerca bibliografica, per il trasferimento delle membrane dai substrati di crescita, in rame, a quelli di destinazione, SiO2 e Si3N4, mantenendo la completa compatibilità con i processi della microelettronica del silicio in particolare per quanto riguarda l’eliminazione dei residui metallici dalla sintesi. Dall’altra è stata sviluppata una procedura di patterning micrometrico del grafene, affidabile e riproducibile, e, soprattutto, compatibile con la microelettronica del silicio. Le membrane, cresciute tramite deposizione da fase vapore (Chemical Vapor Deposition), sono state caratterizzate tramite la microscopia elettronica, a scansione e in trasmissione, la microscopia ottica, spettroscopia Raman e microscopia a forza atomica, tecniche che sono state utilizzate per caratterizzare i campioni durante l'intero processo di patterning. Il processo di etching del grafene in ossigeno, realizzato con il plasma cleaner, strumento che nasce per la pulizia di campioni per microscopia elettronica, è stato messo a punto il attraverso una estesa attività di test sia dei parametri di funzionamento dello strumento che del fotoresist da utilizzare. La procedura di patterning micrometrico vera e propria, ha comportato di affrontare diverse classi di problemi, dalla rimozione del fotoresist con soluzioni diverse (soluzione di sviluppo dedicata e/o acetone) alla rimozione dei residui presenti sulle membrane di grafene anche a valle del patterning stesso. La rimozione dei residui tramite acido cloridrico, insieme ad una procedura di annealing a 400°C in aria per la rimozione dei residui del fotoresist polimerico che erano presenti a valle dell’etching in ossigeno, ha permesso di ottenere un patterning del grafene ben definito su scala micrometrica e una ridottissima presenza di residui. Le procedure ottimizzate di trasferimento e di patterning sono il principale avanzamento rispetto allo stato dell’arte. Le metodiche messe a punto in questo lavoro, consentiranno di integrare il grafene direttamente nel processo di micro-fabbricazione di dispositivi per misure termiche e termoelettriche, per i quali quali sono in realizzazione le maschere di processo che rappresentando la naturale conclusione del lavoro di tesi.

Studio di semiconduttori mesoporosi

I semiconduttori porosi in passato erano considerati dannosi per l'industria microelettronica: solo negli ultimi decenni è stato scoperto che essi posseggono particolari proprietà che li differenziano fortemente dai rispettivi semiconduttori integri, pertanto questa categoria di materiali oggi rappresenta un nuovo settore di ricerca. In questo lavoro di tesi si discutono: la classificazione, la geometria e la morfologia delle strutture porose; la tecnica di "etching" elettrochimico impiegata per realizzare i pori nei semiconduttori; i modelli e i meccanismi di formazione dei pori; la tecnica di spettroscopia elettrochimica FFT-IS("Fast Fourier Transform Impedance Spectroscopy") utile nell'analisi in tempo reale della formazione dei pori; le possibili applicazioni di questi materiali.

Late Infiltration of Post-orthodontic White Spot Lesions

White spot lesion (WSL) infiltration has been recommended immediately after debonding of orthodontic brackets. It is however not clear if established inactive WSLs can also be masked through infiltrationOrthodontic treatment of a 19-year-old patient had to be terminated prematurely due to development of multiple WSLs of varying severity. Three months after debonding, the patient presented for lesion infiltration. After etching with 15% HCl gel and re-wetting of the dried surfaces it seemed that a good outcome could be expected. Lesion infiltration led to complete masking of less severe WSLs. The visual appearance of moderate and severe WSLs was improved but they were still visible after treatment.Inactive WSLs may not represent an increased caries risk, but patients are often bothered esthetically. Infiltration by repeated etching might be a viable approach even for inactive WSLs. Controlled clinical trials are needed to investigate the long-term performance of this technique.

Fabrication of cone-shaped boron doped diamond and gold nanoelectrodes for AFM-SECM

We demonstrate a reliable microfabrication process for a combined atomic force microscopy (AFM) and scanning electrochemical microscopy (SECM) measurement tool. Integrated cone-shaped sensors with boron doped diamond (BDD) or gold (Au) electrodes were fabricated from commercially available AFM probes. The sensor formation process is based on mature semiconductor processing techniques, including focused ion beam (FIB) machining, and highly selective reactive ion etching (RIE). The fabrication approach preserves the geometry of the original AFM tips resulting in well reproducible nanoscaled sensors. The feasibility and functionality of the fully featured tips are demonstrated by cyclic voltammetry, showing good agreement between the measured and calculated currents of the cone-shaped AFM-SECM electrodes.

Penetration ability and microleakage of a fissure sealant applied on artificial and natural enamel fissure caries

OBJECTIVES AND METHODS: This study investigated the sealing ability of a current available unfilled fissure sealant applied over sound (n=80), artificially created (n=80) and naturally carious fissures (n=80) under different humidity conditions (90+/-2 and 45+/-2% relative humidity) and etching times (40 and 60s). All samples were submitted to 5000 thermal cycles and examined by light microscopy after sectioning. Microleakage, penetration ability, fissure type, fissure entrance angle, sealant occlusal length, caries location and caries depth were assessed. RESULTS: The significantly longer sealant occlusal length and larger entrance angle exhibited by shallow fissures, contributed to their higher microleakage and smaller amounts of unfilled areas compared to deep fissures. Sealant microleakage was significantly influenced by the condition of the enamel (sound, artificial and natural caries) and the caries location in the fissures, but not by enamel caries depth (D1 and D2), etching time, or humidity condition. Natural caries exhibited significantly higher microleakage than sound or artificially created carious fissures. CONCLUSIONS: Based on the results of this study, it can be concluded that location of caries in the fissure rather than its depth should be taken into account when applying a fissure sealant. When the borders of the fissure sealant are on carious enamel, a significantly higher microleakage must be expected. The artificial caries model was not a suitable method to assess the behavior of natural fissure caries.