Analysis of the Mechanical Properties of Multicrystalline and Monocrystalline Silicon Wafers Manufactured by Casting Methods

Quasi-monocrystalline silicon wafers have appeared as a critical innovation in the PV industry, joining the most favourable characteristics of the conventional substrates: the higher solar cell efficiencies of monocrystalline Czochralski-Si (Cz-Si) wafers and the lower cost and the full square-shape of the multicrystalline ones. However, the quasi-mono ingot growth can lead to a different defect structure than the typical Cz-Si process. Thus, the properties of the brand-new quasi-mono wafers, from a mechanical point of view, have been for the first time studied, comparing their strength with that of both Cz-Si mono and typical multicrystalline materials. The study has been carried out employing the four line bending test and simulating them by means of FE models. For the analysis, failure stresses were fitted to a three-parameter Weibull distribution. High mechanical strength was found in all the cases. The low quality quasi-mono wafers, interestingly, did not exhibit critical strength values for the PV industry, despite their noticeable density of extended defects.

Contribution to the quality improvement of the antenna measurement using post-processing techniques = Contribución a la mejora de la calidad de medida de antena usando técnicas de post-procesado

One important task in the design of an antenna is to carry out an analysis to find out the characteristics of the antenna that best fulfills the specifications fixed by the application. After that, a prototype is manufactured and the next stage in design process is to check if the radiation pattern differs from the designed one. Besides the radiation pattern, other radiation parameters like directivity, gain, impedance, beamwidth, efficiency, polarization, etc. must be also evaluated. For this purpose, accurate antenna measurement techniques are needed in order to know exactly the actual electromagnetic behavior of the antenna under test. Due to this fact, most of the measurements are performed in anechoic chambers, which are closed areas, normally shielded, covered by electromagnetic absorbing material, that simulate free space propagation conditions, due to the absorption of the radiation absorbing material. Moreover, these facilities can be employed independently of the weather conditions and allow measurements free from interferences. Despite all the advantages of the anechoic chambers, the results obtained both from far-field measurements and near-field measurements are inevitably affected by errors. Thus, the main objective of this Thesis is to propose algorithms to improve the quality of the results obtained in antenna measurements by using post-processing techniques and without requiring additional measurements. First, a deep revision work of the state of the art has been made in order to give a general vision of the possibilities to characterize or to reduce the effects of errors in antenna measurements. Later, new methods to reduce the unwanted effects of four of the most commons errors in antenna measurements are described and theoretical and numerically validated. The basis of all them is the same, to perform a transformation from the measurement surface to another domain where there is enough information to easily remove the contribution of the errors. The four errors analyzed are noise, reflections, truncation errors and leakage and the tools used to suppress them are mainly source reconstruction techniques, spatial and modal filtering and iterative algorithms to extrapolate functions. Therefore, the main idea of all the methods is to modify the classical near-field-to-far-field transformations by including additional steps with which errors can be greatly suppressed. Moreover, the proposed methods are not computationally complex and, because they are applied in post-processing, additional measurements are not required. The noise is the most widely studied error in this Thesis, proposing a total of three alternatives to filter out an important noise contribution before obtaining the far-field pattern. The first one is based on a modal filtering. The second alternative uses a source reconstruction technique to obtain the extreme near-field where it is possible to apply a spatial filtering. The last one is to back-propagate the measured field to a surface with the same geometry than the measurement surface but closer to the AUT and then to apply also a spatial filtering. All the alternatives are analyzed in the three most common near-field systems, including comprehensive noise statistical analyses in order to deduce the signal-to-noise ratio improvement achieved in each case. The method to suppress reflections in antenna measurements is also based on a source reconstruction technique and the main idea is to reconstruct the field over a surface larger than the antenna aperture in order to be able to identify and later suppress the virtual sources related to the reflective waves. The truncation error presents in the results obtained from planar, cylindrical and partial spherical near-field measurements is the third error analyzed in this Thesis. The method to reduce this error is based on an iterative algorithm to extrapolate the reliable region of the far-field pattern from the knowledge of the field distribution on the AUT plane. The proper termination point of this iterative algorithm as well as other critical aspects of the method are also studied. The last part of this work is dedicated to the detection and suppression of the two most common leakage sources in antenna measurements. A first method tries to estimate the leakage bias constant added by the receiver’s quadrature detector to every near-field data and then suppress its effect on the far-field pattern. The second method can be divided into two parts; the first one to find the position of the faulty component that radiates or receives unwanted radiation, making easier its identification within the measurement environment and its later substitution; and the second part of this method is able to computationally remove the leakage effect without requiring the substitution of the faulty component. Resumen Una tarea importante en el diseño de una antena es llevar a cabo un análisis para averiguar las características de la antena que mejor cumple las especificaciones fijadas por la aplicación. Después de esto, se fabrica un prototipo de la antena y el siguiente paso en el proceso de diseño es comprobar si el patrón de radiación difiere del diseñado. Además del patrón de radiación, otros parámetros de radiación como la directividad, la ganancia, impedancia, ancho de haz, eficiencia, polarización, etc. deben ser también evaluados. Para lograr este propósito, se necesitan técnicas de medida de antenas muy precisas con el fin de saber exactamente el comportamiento electromagnético real de la antena bajo prueba. Debido a esto, la mayoría de las medidas se realizan en cámaras anecoicas, que son áreas cerradas, normalmente revestidas, cubiertas con material absorbente electromagnético. Además, estas instalaciones se pueden emplear independientemente de las condiciones climatológicas y permiten realizar medidas libres de interferencias. A pesar de todas las ventajas de las cámaras anecoicas, los resultados obtenidos tanto en medidas en campo lejano como en medidas en campo próximo están inevitablemente afectados por errores. Así, el principal objetivo de esta Tesis es proponer algoritmos para mejorar la calidad de los resultados obtenidos en medida de antenas mediante el uso de técnicas de post-procesado. Primeramente, se ha realizado un profundo trabajo de revisión del estado del arte con el fin de dar una visión general de las posibilidades para caracterizar o reducir los efectos de errores en medida de antenas. Después, se han descrito y validado tanto teórica como numéricamente nuevos métodos para reducir el efecto indeseado de cuatro de los errores más comunes en medida de antenas. La base de todos ellos es la misma, realizar una transformación de la superficie de medida a otro dominio donde hay suficiente información para eliminar fácilmente la contribución de los errores. Los cuatro errores analizados son ruido, reflexiones, errores de truncamiento y leakage y las herramientas usadas para suprimirlos son principalmente técnicas de reconstrucción de fuentes, filtrado espacial y modal y algoritmos iterativos para extrapolar funciones. Por lo tanto, la principal idea de todos los métodos es modificar las transformaciones clásicas de campo cercano a campo lejano incluyendo pasos adicionales con los que los errores pueden ser enormemente suprimidos. Además, los métodos propuestos no son computacionalmente complejos y dado que se aplican en post-procesado, no se necesitan medidas adicionales. El ruido es el error más ampliamente estudiado en esta Tesis, proponiéndose un total de tres alternativas para filtrar una importante contribución de ruido antes de obtener el patrón de campo lejano. La primera está basada en un filtrado modal. La segunda alternativa usa una técnica de reconstrucción de fuentes para obtener el campo sobre el plano de la antena donde es posible aplicar un filtrado espacial. La última es propagar el campo medido a una superficie con la misma geometría que la superficie de medida pero más próxima a la antena y luego aplicar también un filtrado espacial. Todas las alternativas han sido analizadas en los sistemas de campo próximos más comunes, incluyendo detallados análisis estadísticos del ruido con el fin de deducir la mejora de la relación señal a ruido lograda en cada caso. El método para suprimir reflexiones en medida de antenas está también basado en una técnica de reconstrucción de fuentes y la principal idea es reconstruir el campo sobre una superficie mayor que la apertura de la antena con el fin de ser capaces de identificar y después suprimir fuentes virtuales relacionadas con las ondas reflejadas. El error de truncamiento que aparece en los resultados obtenidos a partir de medidas en un plano, cilindro o en la porción de una esfera es el tercer error analizado en esta Tesis. El método para reducir este error está basado en un algoritmo iterativo para extrapolar la región fiable del patrón de campo lejano a partir de información de la distribución del campo sobre el plano de la antena. Además, se ha estudiado el punto apropiado de terminación de este algoritmo iterativo así como otros aspectos críticos del método. La última parte de este trabajo está dedicado a la detección y supresión de dos de las fuentes de leakage más comunes en medida de antenas. El primer método intenta realizar una estimación de la constante de fuga del leakage añadido por el detector en cuadratura del receptor a todos los datos en campo próximo y después suprimir su efecto en el patrón de campo lejano. El segundo método se puede dividir en dos partes; la primera de ellas para encontrar la posición de elementos defectuosos que radian o reciben radiación indeseada, haciendo más fácil su identificación dentro del entorno de medida y su posterior substitución. La segunda parte del método es capaz de eliminar computacionalmente el efector del leakage sin necesidad de la substitución del elemento defectuoso.

Germination ecology of the perennial Centaurium somedanum, a specialist species of mountain springs

To improve understanding of how a rare endemic species of Centaurium adapts to a specialized ecological niche, we studied the germination ecology of the mountain spring specialist, C. somedanum, a perennial species restricted to an unusual habitat for this genus. We conducted laboratory experiments with fresh seeds collected from two populations for three consecutive years, to investigate: (1) the effect of temperature and light ongermination; (2) the existence of seed dormancy; and (3) inter-population and inter-annual variation in germinability. Germination occurred only in the light and at relatively low temperatures (15?228C) with no differences between constant and alternating regimes, and a significant decrease at high temperatures (258C and 308C). We found non-deep simple morphophysiological dormancy and variation in seed germinability depending on the year of seed collection. C. somedanum diverged from the common germination characteristics of the genus in: (1) its germination at lower temperatures, which contrasts with what is generally expected in wetland species but could be adaptive in the spring habitat; and (2) its morphophysiological dormancy, which we report here for the first time in the genus and which could be an adaptation to its mountain habitat.

Assessing the landscape value of public works: validation of the method in the lowlands of the middle section of the Tajo river (Spain)

This paper proposes a method of landscape characterisation and assessment of public works associated with fluvial landscapes, which is validated in the middle section of the Tajo River. In this method, a set of criteria is identified that unifies various characteristics of the landscape associated to the infrastructures. A specific weight is then assigned to each criterion in such a way as to produce a semi-quantitative value ranging from a minimum value of 0 to a maximum value of 10. Taken together, these criteria enable us to describe and assess the value of the public works selected for study, in this case helping us to evaluate the sections of the River Tajo analysed in our study area. Accordingly, the value of all the infrastructures associated to a stretch of the river covering several hundred kilometres was determined and after dividing this stretch into sections, they were compared under equivalent conditions to provide a hierarchal ranking.

A new approach to a model of the mammalian retina with optically programmable logic cells

This paper reports a model of the mammalian retina as well as an interpretation of some functions of the visual cortex. Its main objective is to simulate some of the behaviors observed at the different retina cells depending on the characteristics of the light impinging onto the photoreceptors. This simulation is carried out with a simple structure employed previously as basic building block of some optical computer architectures. Its possibility to perform any type of Boolean function allows a wide range of behaviors.

An Empirical Analysis of the Spanish Gas Price Structure

We can say without hesitation that in energy markets a throughout data analysis is crucial when designing sophisticated models that are able to capture most of the critical market drivers. In this study we will attempt to investigate into Spanish natural gas prices structure to improve understanding of the role they play in the determination of electricity prices and decide in the future about price modelling aspects. To further understand the potential for modelling, this study will focus on the nature and characteristics of the different gas price data available. The fact that the existing gas market in Spain does not incorporate enough liquidity of trade makes it even more critical to analyze in detail available gas price data information that in the end will provide relevant information to understand how electricity prices are affected by natural gas markets. In this sense representative Spanish gas prices are typically difficult to explore given the fact that there is not a transparent gas market yet and all the gas imported in the country is negotiated and purchased by private companies at confidential terms.

El lugar de la mente. Sobre la capilla Sogn Benedetg de Peter Zumthor en Sumvitg/ The place of the mind. On Peter Zumthor’s Sogn Benedetg Chapel in Sumvitg

La Capilla de Sogn Benedetg en Sumvitg, parte de la obra temprana de Peter Zumthor, condensa aspectos de sus ideas, de su forma de proyectar y construir, que aún hoy siguen vigentes en él. Los recuerdos de infancia cimientan su enfoque de la arquitectura, en el que trata de reunir trazas de la vida cotidiana, sensible al lugar y utilizando materiales tratados de un modo preciso que bajo la luz adquieren su presencia. Con un lenguaje táctil y tectónico, desde una aproximación fenomenológica, persigue compartir una experiencia multisensorial, englobando percepciones complementarias que trascienden la geometría visual. Como Kahn, se apoya en el pensamiento de Heidegger, y se inspira en la pequeña cabaña que el filósofo habitaba en la Selva Negra, así como en la arquitectura religiosa de Rudolf Schwarz, cuya huella puede apreciarse tanto en el edificio como en los objetos que se encuentran en él. La tensión que genera entre interior y exterior mantiene despiertos los sentidos del visitante, a la vez que las características de la capilla enlazan con un regionalismo integrador que no se aparta de las formas abstractas contemporáneas. : Sogn Benedetg Chapel in Sumvitg, part of the early work of Peter Zumthor, condenses aspects of his ideas and his way of designing and building, which still remain valid today. Remembrances of childhood lay the foundation for his focus to architecture, which involves the collection of daily life traces, sensitive to the place and using materials treated in a precise manner, acquiring their presence under the light. With a tactile and tectonic language, from a phenomenological approach, he seeks to share a multi-sensory experience, encompassing complementary perceptions that transcend the visual geometry. As Kahn does, he relies on Heidegger?s thinking and is inspired by the little hut that the philosopher inhabited in the Black Forest, as well as by Rudolf Schwarz?s religious architecture, whose imprint can be appreciated in both the building and the objects encountered within it. The tension generated between interior and exterior keeps awake the senses of the visitor, while the characteristics of the chapel connect with an integrative regionalism that does not exclude contemporary abstract forms.

Microstructural and mechanical characteristics of W-2Ti and W-1TiC processed by hot isostatic pressing

W–2Ti and W–1TiC alloys were produced by mechanical alloying and consolidation by hot isostatic pressing. The composition and microstructural characteristics of these alloys were studied by X-ray diffraction, energy dispersion spectroscopy and scanning electron microscopy. The mechanical behavior of the consolidated alloys was characterized by microhardness measurements and three point bending tests. The mechanical characteristics of the W–2Ti alloy appear to be related to solution hardening. In W–1TiC, the residual porosity should be responsible for the poor behavior observed in comparison with W–2Ti.

Análisis cualitativo de la relación entrenador-deportista en etapas de formación en baloncesto = Qualitative analysis of the coach-athlete relationship in youth basketball

La relación entrenador-deportista estudia, dentro del ámbito de la psicología social en el deporte, la interacción de los comportamientos, sentimientos y emociones de ambos miembros de la pareja. Se entiende como un proceso en el que antecedentes como la edad, el género o las características esperadas en el otro condicionan el desarrollo de diferentes componentes, los cuales determinan la calidad de la relación, obteniéndose diferentes resultados tanto a nivel deportivo como personal. En la presente tesis se han estudiado 12 relaciones positivas entrenador-deportista en categorías de formación en baloncesto con el objetivo de conocer los condicionantes, componentes, estrategias y resultados de relaciones efectivas. Para ello, se ha realizado un estudio cualitativo, cuya muestra (N=24) se ha seleccionado de manera deliberada discriminando variables como el nivel deportivo del equipo, las características del entrenador, la duración y la calidad de la relación. Las 12 díadas participaban en el máximo nivel de su categoría, tenían una duración mínima de dos temporadas y fueron calificadas como positivas por los entrenadores principales. La investigación se ha llevado a cabo desde la perspectiva holística del fenómeno, teniendo en cuenta tanto el punto de vista del entrenador como el del jugador. Para la recogida de datos se utilizó la entrevista semiestructurada y en profundidad. Los resultados señalan la necesidad de desarrollar estrategias que promuevan y mantengan relaciones de calidad en baloncesto, ya que éstas tienen un alto impacto en el progreso deportivo y personal de los jugadores jóvenes en baloncesto. Entre los condicionantes de la relación entrenador-deportista se ha percibido que las expectativas formadas en los primeros contactos pueden determinar la calidad de la relación. Por otro lado, los componentes dan lugar a resultados como el crecimiento a nivel personal por parte de los jugadores o un mayor rendimiento deportivo, producido en gran medida por la satisfacción y el bienestar psicológico tanto del entrenador como del jugador. Por último, los resultados indican la importancia de adecuar el comportamiento del entrenador a las características propias de los jugadores en cada categoría de formación. ABSTRACT The coach-athlete relationship studies, within the field of social psychology in sport, the interaction of behavior, feelings and emotions in both partners. It is understood as a process in which antecedents such as age, gender or expectations develop different components. The quality of the relationship is determined by these three elements, leading to different results in sport performance as in personal variables. This thesis examined 12 positive coach-athlete rapports in youth basketball teams in order to better understand the determinants, components, strategies and outcomes of effective relationships. A qualitative study has been carried out. The sample (N = 24) is selected deliberately discriminating variables such as the team’s sportive level, coach characteristics, duration and quality of the relationship. Twelve dyads participated at the highest level in its category, had a minimum of two seasons and were rated as positive by head coaches. The research was conducted from a holistic perspective of the phenomenon, taking into account the point of view of both the coach and the player. Indepth semi-structured interview was used for data collection. The results report the need to develop strategies to promote and maintain high quality relationships in basketball, because they have an important impact in sport and personal development of young basketball players. Expectations raised through different impression cues in the first contacts can determine the quality of the relationship. On the other hand, the components lead to results such as players’ personal growth or sport performance, largely produced by the satisfaction and psychological well being of both the coach and the player. Finally, the results indicate the importance of adapting the coach’s behavior to the characteristics of the different stages of young athletes’ development.

An engineering modification of the blade element momentum combination applicable in vertical descent flight :fundamentals and validation

An engineering modification of blade element/momentum theory is applied to describe the vertical autorotation of helicopter rotors. A full non‐linear aerodynamic model is considered for the airfoils, taking into account the dependence of lift and drag coefficients on both the angle of attack and the Reynolds number. The proposed model, which has been validated in previous work, has allowed the identification of different autorotation modes, which depend on the descent velocity and the twist of the rotor blades. These modes present different radial distributions of driven and driving blade regions, as well as different radial upwash/downwash patterns. The number of blade sections with zero tangential force, the existence of a downwash region in the rotor disk, the stability of the autorotation state, and the overall rotor autorotation efficiency, are all analyzed in terms of the flight velocity and the characteristics of the rotor. It is shown that, in vertical autorotation, larger blade twist leads to smaller values of descent velocity for a given thrust generated by the rotor in the autorotational state.

An engineering modification of the blade element momentum equation for vertical descent : an autoration case study

An engineering modification of blade element/momentum theory is applied to describe the vertical autorotation of helicopter rotors. A full non-linear aerodynamic model is considered for the airfoils, taking into account the dependence of lift and drag coefficients on both the angle of attack and the Reynolds number. The proposed model, which has been validated in previous work, has allowed the identification of different autorotation modes, which depend on the descent velocity and the twist of the rotor blades. These modes present different radial distributions of driven and driving blade regions, as well as different radial upwash/downwash patterns. The number of blade sections with zero tangential force, the existence of a downwash region in the rotor disk, the stability of the autorotation state, and the overall rotor autorotation efficiency, are all analyzed in terms of the flight velocity and the characteristics of the rotor. It is shown that, in vertical autorotation, larger blade twist leads to smaller values of descent velocity for a given thrust generated by the rotor in the autorotational state.

Study of the influence of actin-binding proteins using linear analyses of cell deformability

The actin cytoskeleton plays a key role in the deformability of the cell and in mechanosensing. Here we analyze the contributions of three major actin cross-linking proteins, myosin II, a-actinin and filamin, to cell deformability, by using micropipette aspiration of Dictyostelium cells. We examine the applicability of three simple mechanical models: for small deformation, linear viscoelasticity and drop of liquid with a tense cortex; and for large deformation, a Newtonian viscous fluid. For these models, we have derived linearized equations and we provide a novel, straightforward methodology to analyze the experiments. This methodology allowed us to differentiate the effects of the cross-linking proteins in the different regimes of deformation. Our results confirm some previous observations and suggest important relations between the molecular characteristics of the actin-binding proteins and the cell behavior: the effect of myosin is explained in terms of the relation between the lifetime of the bond to actin and the resistive force; the presence of a-actinin obstructs the deformation of the cytoskeleton, presumably mainly due to the higher molecular stiffness and to the lower dissociation rate constants; and filamin contributes critically to the global connectivity of the network, possibly by rapidly turning over crosslinks during the remodeling of the cytoskeletal network, thanks to the higher rate constants, flexibility and larger size. The results suggest a sophisticated relationship between the expression levels of actinbinding proteins, deformability and mechanosensing.

Application of the homogenization techniques to the determination of the effective flexure constants of plate structural systems

A Mindlin plate with periodically distributed ribs patterns is analyzed by using homogenization techniques based on asymptotic expansion methods. The stiffness matrix of the homogenized plate is found to be dependent on the geometrical characteristics of the periodical cell, i.e. its skewness, plan shape, thickness variation etc. and on the plate material elastic constants. The computation of this plate stiffness matrix is carried out by averaging over the cell domain some solutions of different periodical boundary value problems. These boundary value problems are defined in variational form by linear first order differential operators on the cell domain and the boundary conditions of the variational equation correspond to a periodic structural problem. The elements of the stiffness matrix of homogenized plate are obtained by linear combinations of the averaged solution functions of the above mentioned boundary value problems. Finally, an illustrative example of application of this homogenization technique to hollowed plates and plate structures with ribs patterns regularly arranged over its area is shown. The possibility of using in the profesional practice the present procedure to the actual analysis of floors of typical buildings is also emphasized.

Loss of transformed phenotype in cancer cells by overexpression of the uteroglobin gene

Uteroglobin (UG) is a multifunctional, secreted protein that has receptor-mediated functions. The human UG (hUG) gene is mapped to chromosome 11q12.2–13.1, a region frequently rearranged or deleted in many cancers. Although high levels of hUG expression are characteristic of the mucosal epithelia of many organs, hUG expression is either drastically reduced or totally absent in adenocarcinomas and in viral-transformed epithelial cells derived from the same organs. In agreement with these findings, in an ongoing study to evaluate the effects of aging on UG-knockout mice, 16/16 animals developed malignant tumors, whereas the wild-type littermates (n = 25) remained apparently healthy even after 1½ years. In the present investigation, we sought to determine the effects of induced-expression of hUG in human cancer cells by transfecting several cell lines derived from adenocarcinomas of various organs with an hUG-cDNA construct. We demonstrate that induced hUG expression reverses at least two of the most important characteristics of the transformed phenotype (i.e., anchorage-independent growth on soft agar and extracellular matrix invasion) of only those cancer cells that also express the hUG receptor. Similarly, treatment of the nontransfected, receptor-positive adenocarcinoma cells with purified recombinant hUG yielded identical results. Taken together, these data define receptor-mediated, autocrine and paracrine pathways through which hUG reverses the transformed phenotype of cancer cells and consequently, may have tumor suppressor-like effects.

On the reaction mechanism of l-lactate oxidase: Quantitative structure-activity analysis of the reaction with para-substituted l-mandelates

The rate constants for reduction of the flavoenzyme, l-lactate oxidase, and a mutant (in which alanine 95 is replaced by glycine), by a series of para-substituted mandelates, in both the 2-1H- and 2-2H- forms, have been measured by rapid reaction spectrophotometry. In all cases, significant isotope effects (1H/2H = 3–7) on the rate constants of flavin reduction were found, indicating that flavin reduction is a direct measure of α-C-H bond breakage. The rate constants show only a small influence of the electronic characteristics of the substituents, but show a good correlation when combined with some substituent volume parameters. A surprisingly good correlation is found with the molecular mass of the substrate. The results are compatible with any mechanism in which there is little development of charge in the transition state. This could be a transfer of hydride to the flavin N(5) position or a synchronous mechanism in which the α-C-H is formally abstracted as a H+ while the resulting charge is simultaneously neutralized by another event.