Control de vibraciones en pasarelas peatonales

En los últimos años se ha construido un gran número de pasarelas peatonales como respuesta a la demanda de nuevas vías de paso en las ciudades. Estas estructuras tienen requisitos constructivos menos exigentes en comparación con otros tipos de puentes, lo cual ha facilitado el desarrollo de diseños con nuevos esquemas resistentes, complicadas geometrías y el empleo de nuevos materiales. En general estas estructuras son esbeltas, ligeras y poco amortiguadas, lo que en ocasiones ha generado problemas de vi-braciones al paso de peatones una vez puestas en servicio. Las normativas actuales son cada vez más sensibles a esta problemática, recomendando diseños cuyas frecuencias naturales deben estar alejadas de los rangos de frecuencia de paso típicos de los peatones y fijando límites de confort en forma de valores máximos de aceleración permitidos, asegurándose así un correcto comportamiento de la estructura. En el presente artículo se analiza esta problemática desde un punto de vista práctico. Para ello se muestran los puntos clave de las normativas y guías de diseño de pasarelas que se pueden encontrar actualmente en la bibliografía, se presentan las técnicas que habitualmente se emplean en el análisis dinámico experimental de estas estructuras, y se comentan las soluciones a las que generalmente se recurre para mejorar su comportamiento dinámico. Por último, se muestran los trabajos llevados a cabo por el Centro Tecnológico CARTIF en colaboración con las Universidades de Valladolid y Castilla-La Mancha en la pasarela peatonal del Museo de la Ciencia de Valladolid. Estos trabajos incluyen: (1) el estudio dinámico de los tres vanos metálicos de dicha pasarela, (2) el diseño e implementación de un amortiguador de masa sintonizado en el vano más sensible a las vibraciones, (3) la implementación de un amortiguador de masa activo utilizando un excitador electrodinámico, y (4) el desarrollo de pruebas para la verificación del estado de servicio de la pasarela. In the last years, a wide number of footbridges have been built as demand response of more direct pathways in cities. These structures have lower building requirements as compared with standard bridges. This circumstance has facilitated the development of new structural design with complex geometries and innovative materials. As a result, these structures may be slender, light and low damped, leading to vibration problems once in service. The current codes take into account this problem, and recommend designs with natural frequencies away from the typical pedestrian pacing rates and fix comfort limits to guarantee the serviceability of the structure.This paper studies this problem from a practical point of view. Thus, the key points of codes and footbridges guidelines are showed, the typical experimental dynamic analysis techniques are presented, and the usual solutions adopted to improve the dynamic performance of these structures are discussed. Finally, the works carried out on the Valladolid Science Museum Footbridge by Centro Tecnológico CARTIF in collaboration with the Universities of Valladolid and Castilla-La Mancha are showed. These works include: (1) the dynamic study of the three steel spans of the footbridge, (2) the design and implementation of a tuned mass damper in the liveliest span, (3) the implementation of an active mass damper using an electrodynamic shaker, and (4) the development of field tests to assess the serviceability of such span.

A comparative study of SISO and MIMO control strategies for floor vibration damping

Civil engineering structures such as floor systems with open-plan layout or lightweight footbridges are susceptible to excessive level of vibrations caused by human loading. Active vibration control (AVC) via inertial mass actuators has been shown to be a viable technique to mitigate vibrations, allowing structures to satisfy vibration serviceability limits. Most of the AVC applications involve the use of SISO (single input single-output) strategies based on collocated control. However, in the case of floor structures, in which mostof the vibration modes are locally spatially distributed, SISO or multi-SISO strategies are quite inefficient. In this paper, a MIMO (multi-inputs multi-outputs) control in decentralised and centralised configuration is designed. The design process simultaneously finds the placement of multiple actuators and sensors and the output feedback gains. Additionally, actuator dynamics, actuator nonlinearities and frequency and time weightings are considered into the design process. Results with SISO and decentralised and centralised MIMO control (for a given number of actuators and sensors) are compared, showing the advantages of MIMO control for floor vibration control.

Control motion approach of a lower limb orthosis to reduce energy consumption

By analysing the dynamic principles of the human gait, an economic gait‐control analysis is performed, and passive elements are included to increase the energy efficiency in the motion control of active orthoses. Traditional orthoses use position patterns from the clinical gait analyses (CGAs) of healthy people, which are then de‐normalized and adjusted to each user. These orthoses maintain a very rigid gait, and their energy cosT is very high, reducing the autonomy of the user. First, to take advantage of the inherent dynamics of the legs, a state machine pattern with different gains in eachstate is applied to reduce the actuator energy consumption. Next, different passive elements, such as springs and brakes in the joints, are analysed to further reduce energy consumption. After an off‐line parameter optimization and a heuristic improvement with genetic algorithms, a reduction in energy consumption of 16.8% is obtained by applying a state machine control pattern, and a reduction of 18.9% is obtained by using passive elements. Finally, by combining both strategies, a more natural gait is obtained, and energy consumption is reduced by 24.6%compared with a pure CGA pattern.

Relative Dynamics and Control of an Ion Beam Shepherd Satellite

The ion beam shepherd (IBS) is a recently proposed concept for modifying the orbit and/or attitude of a generic orbiting body in a contactless manner, which makes it a candidate technology for active space debris removal. In this paper we deal with the problem of controlling the relative position of a shepherd satellite coorbiting at small separation distance with a target debris. After deriving the orbit relative motion equations including the effect of the ion beam perturbation we study the system stability and propose different control strategies.

Dual Active Bridge based Battery Charger for Plug-in Hybrid Electric Vehicle with Charging Current Containing Low Frequency Ripple

High power density is strongly preferable for the on-board battery charger of Plug-in Hybrid Electric Vehicle (PHEV). Wide band gap devices, such as Gallium Nitride HEMTs are being explored to push to higher switching frequency and reduce passive component size. In this case, the bulk DC link capacitor of AC-DC Power Factor Correction (PFC) stage, which is usually necessary to store ripple power of two times the line frequency in a DC current charging system, becomes a major barrier on power density. If low frequency ripple is allowed in the battery, the DC link capacitance can be significantly reduced. This paper focuses on the operation of a battery charging system, which is comprised of one Full Bridge (FB) AC-DC stage and one Dual Active Bridge (DAB) DC-DC stage, with charging current containing low frequency ripple at two times line frequency, designated as sinusoidal charging. DAB operation under sinusoidal charging is investigated. Two types of control schemes are proposed and implemented in an experimental prototype. It is proved that closed loop current control is the better. Full system test including both FB AC-DC stage and DAB DC-DC stage verified the concept of sinusoidal charging, which may lead to potentially very high power density battery charger for PHEV.

Contribution to active multi-beam reconfigurable antennas for L and S bands

La presente tesis doctoral con título "Contribution to Active Multi-Beam Reconfigurable Antennas for L and S Bands" ha sido desarrollada por el investigador ingeniero de telecomunicación estudiante de doctorado Javier García-Gasco Trujillo en el Grupo de Radiación del Departamento de Señales, Sistemas y Radiocomunicaciones de la ETSI de Telecomunicación de la Universidad Politécnica de Madrid bajo la dirección de los doctores Manuel Sierra Pérez y José Manuel Fernández González. Durante décadas, el desarrollo de antenas de apuntamiento electrónico ha estado limitado al área militar. Su alto coste y su gran complejidad eran los mayores obstáculos que frenaban la introducción de esta tecnología en aplicaciones comerciales de gran escala. La reciente aparición de componentes de estado sólido prácticos, fiables, y de bajo coste ha roto la barrera del coste y ha reducido la complejidad, haciendo que las antenas reconfigurables de apuntamiento electrónico sean una opción viable en un futuro cercano. De esta manera, las antenas phased array podrían llegar a ser la joya de la corona que permitan alcanzar los futuros retos presentes en los sistemas de comunicaciones tanto civiles como militares. Así pues, ahora es el momento de investigar en el desarrollo de antenas de apuntamiento electrónico de bajo coste, donde los nuevos componentes de estado sólido comerciales forman el núcleo duro de la arquitectura. De esta forma, el estudio e implementación de estos arrays de antenas activas de apuntamiento electrónico capaces de controlar la fase y amplitud de las distintas señales implicadas es uno de los grandes retos de nuestro tiempo. Esta tesis se enfrenta a este desafío, proponiendo novedosas redes de apuntamiento electrónico e innovadores módulos de transmisión/recepción (T/R) utilizando componentes de estado sólido de bajo coste, que podrán integrar asequibles antenas activas reconfigurables multihaz en bandas L y S. En la primera parte de la tesis se realiza una descripción del estado del arte de las antenas phased array, incluyendo su base teórica y sus ventajas competitivas. Debido a que las contribuciones obtenidas en la presente tesis han sido realizadas dentro de distintos proyectos de investigación, donde se han manejada antenas de simple/doble polarización circular y simple/doble banda de trabajo, se describen detenidamente los dos proyectos más relevantes de la investigación: el radar de basura espacial de la Agencia Espacial Europea (ESA), Space Situational Awareness (SSA); y la estación base de seguimiento y control de satélites de órbita baja, GEOdesic Dome Array (GEODA). Sin lugar a dudas, los dispositivos desfasadores son uno de los componentes clave en el diseño de antenas phased arrays. Recientemente se ha observado una gran variación en el precio final de estos dispositivos, llegando en ocasiones a límites inasequibles. Así pues, se han propuesto distintas técnicas de conformación de haz alternativas a la utilización de componentes desfasadores comerciales: el desfasador de líneas conmutadas, la red de haz conmutado, y una novedosa red desfasadora divisora/combinadora de potencia. Para mostrar un uso práctico de las mismas, se ha propuesto el uso de las tres alternativas para el caso práctico del subarray de cinco elementos de la celda GEODA-SARAS. Tras dicho estudio se obtiene que la novedosa red desfasadora divisora/combinadora de potencia propuesta es la que mejor relación comportamiento/coste presenta. Para verificar su correcto funcionamiento se construye y mide los dos bloques principales de los que está compuesta la red total, comprobando que en efecto la red responde según lo esperado. La estructura más simple que permite realizar un barrido plano es el array triangular de tres elementos. Se ha realizado el diseño de una nueva red multihaz que es capaz de proporcionar tres haces ortogonales en un ángulo de elevación _0 y un haz adicional en la dirección broadside utilizando el mencionado array triangular de tres elementos como antena. En primer lugar se realizar una breve introducción al estado del arte de las redes clásicas multihaz. Así mismo se comentan innovadores diseños de redes multihaz sin pérdidas. El estudio da paso a las redes disipativas, de tal forma que se analiza su base matemática y se muestran distintas aplicaciones en arrays triangulares de tres elementos. Finalmente, la novedosa red básica propuesta se presenta, mostrando simulaciones y medidas de la misma para el caso prácticoo de GEODA. También se ha diseñado, construido y medido una red compuesta por dos redes básicas complementarias capaz de proporcionar seis haces cuasi-ortogonales en una dirección _0 con dos haces superpuestos en broadside. La red propuesta queda totalmente validada con la fabricación y medida de estos con prototipos. Las cadenas de RF de los módulos T/R de la nueva antena GEODA-SARAS no son algo trivial. Con el fin de mostrar el desarrollo de una cadena compleja con una gran densidad de componentes de estado sólido, se presenta una descripción detallada de los distintos componentes que integran las cadenas de RF tanto en transmisión como en recepción de la nueva antena GEODA-SARAS. Tras presentar las especificaciones de la antena GEODA-SARA y su diagrama de bloques esquemático se describen los dos bloques principales de las cadenas de RF: la celda de cinco elementos, y el módulo de conversión de panel. De la misma manera también se presentará el módulo de calibración integrado dentro de los dos bloques principales. Para comprobar que el funcionamiento esperado de la placa es el adecuado, se realizará un análisis que tratará entre otros datos: la potencia máxima en la entrada del transmisor (comprobando la saturación de la cadena), señal de recepción mínima y máxima (verificando el rango de sensibilidad requerido), y el factor G/T (cumpliendo la especificación necesaria). Así mismo se mostrará un breve estudio del efecto de la cuantificación de la fase en el conformado de haz de RF. Los estudios muestran que la composición de las cadenas de RF permite el cumplimiento de las especificaciones necesarias. Finalmente la tesis muestra las conclusiones globales del trabajo realizado y las líneas futuras a seguir para continuar con esta línea de investigación. ABSTRACT This PhD thesis named "Contribution to Active Multi-Beam Reconfigurable Antennas for L and S Bands", has been written by the Electrical Engineer MSc. researcher Javier García-Gasco Trujillo in the Grupo de Radiación of the Departamento de Señales, Sistemas y Radiocomunicaciones from the ETSI de Telecomunicación of the Universidad Politécnica de Madrid. For decades, the implementation of electronically steerable phased array antennas was confined to the military area. Their high cost and complexity were the major obstacles to introduce this technology in large scale commercial applications. The recent emergence of new practical, low-cost, and highly reliable solid state devices; breaks the barrier of cost and reduces the complexity, making active phased arrays a viable future option. Thus, phased array antennas could be the crown jewel that allow to meet the future challenges in military and civilian communication systems. Now is time to deploy low-cost phased array antennas, where newly commercial components form the core of the architecture. Therefore, the study and implementation of these novel low-cost and highly efficient solid state phased array blocks capable of controlling signal phase/amplitude accurately is one of the great challenges of our time. This thesis faces this challenge, proposing innovative electronic beam steering networks and transmitter/ receiver (T/R) modules using affordable solid state components, which could integrate fair reconfigurable phased array antennas working in L and S bands. In the first part of the thesis, a description of the state of art of phased array antennas, including their fundamentals and their competitive advantages, is presented. Since thesis contributions have been carried out for different research projects, where antennas with single/double circular polarization and single/double working frequency bands have been examined, frameworks of the two more important projects are detailed: the Space Situational Awareness (SSA) programme from the European Space Agency (ESA), and the GEOdesic Dome Array (GEODA) project from ISDEFE-INSA and the ESA. Undoubtedly, phase shifter devices are one of the key components of phased array antennas. Recent years have witnessed wide fluctuations in commercial phase shifter prices, which sometimes led to unaffordable limit. Several RF steering technique alternatives to the commercial phase shifters are proposed, summarized, and compared: the switched line phase shifter, the switched-beam network, and the novel phase shifter power splitter/combiner network. In order to show a practical use of the three different techniques, the five element GEODA-SARAS subarray is proposed as a real case of study. Finally, a practical study of a newly phase shifter power splitter/combiner network for a subarray of five radiating elements with triangular distribution is shown. Measurements of the two different phase shifter power splitter/combiner prototypes integrating the whole network are also depicted, demonstrating their proper performance. A triangular cell of three radiating elements is the simplest way to obtain a planar scanner. A new multibeam network configuration that provides three orthogonal beams in a desired _0 elevation angle and an extra one in the broadside steering direction for a triangular array of three radiating elements is introduced. Firstly, a short introduction to the state of art of classical multi-beam networks is presented. Lossless network analysis, including original lossless network designs, are also commented. General dissipative network theory as well as applications for array antennas of three radiating elements are depicted. The proposed final basic multi-beam network are simulated, built and measured to the GEODA cell practical case. A combined network that provides six orthogonal beams in a desired _0 elevation angle and a double seventh one in the broadside direction by using two complementary proposed basic networks will be shown. Measurements of the whole system will be also depicted, verifying the expected behavior. GEODA-SARAS T/R module RF chains are not a trivial design. A thorough description of all the components compounding GEODA-SARAS T/R module RF chains is presented. After presenting the general specifications of the GEODA-SARAS antenna and its block diagrams; two main blocks of the RF chains, the five element cell and the panel conversion module, are depicted and analyzed. Calibration module integrated within the two main blocks are also depicted. Signal flow throw the system analyzing critical situations such as maximum transmitted power (testing the chain unsaturation), minimum and maximum receiving signal (verifying sensitivity range), maximum receiver interference signals (assuring a proper reception), and G/T factor (fulfilling the technical specification) are evaluated. Phase quantization error effects are also listed. Finally, the manuscript contains the conclusions drawn of the present research and the future work.

Magnetic Attitude Control System for a Small Satellite. Impact on the Thermal Performance

El principal objetivo de la tesis es estudiar el acoplamiento entre los subsistemas de control de actitud y de control térmico de un pequeño satélite, con el fin de buscar la solución a los problemas relacionados con la determinación de los parámetros de diseño. Se considera la evolución de la actitud y de las temperaturas del satélite bajo la influencia de dos estrategias de orientación diferentes: 1) estabilización magnética pasiva de la orientación (PMAS, passive magnetic attitude stabilization), y 2) control de actitud magnético activo (AMAC, active magnetic attitude control). En primer lugar se presenta el modelo matemático del problema, que incluye la dinámica rotacional y el modelo térmico. En el problema térmico se considera un satélite cúbico modelizado por medio de siete nodos (seis externos y uno interno) aplicando la ecuación del balance térmico. Una vez establecido el modelo matemático del problema, se estudia la evolución que corresponde a las dos estrategias mencionadas. La estrategia PMAS se ha seleccionado por su simplicidad, fiabilidad, bajo coste, ahorrando consumo de potencia, masa coste y complejidad, comparado con otras estrategias. Se ha considerado otra estrategia de control que consigue que el satélite gire a una velocidad requerida alrededor de un eje deseado de giro, pudiendo controlar su dirección en un sistema inercial de referencia, ya que frecuentemente el subsistema térmico establece requisitos de giro alrededor de un eje del satélite orientado en una dirección perpendicular a la radiación solar incidente. En relación con el problema térmico, para estudiar la influencia de la velocidad de giro en la evolución de las temperaturas en diversos puntos del satélite, se ha empleado un modelo térmico linealizado, obtenido a partir de la formulación no lineal aplicando un método de perturbaciones. El resultado del estudio muestra que el tiempo de estabilización de la temperatura y la influencia de las cargas periódicas externas disminuye cuando aumenta la velocidad de giro. Los cambios de temperatura se reducen hasta ser muy pequeños para velocidades de rotación altas. En relación con la estrategia PMAC se ha observado que a pesar de su uso extendido entre los micro y nano satélites todavía presenta problemas que resolver. Estos problemas están relacionados con el dimensionamiento de los parámetros del sistema y la predicción del funcionamiento en órbita. Los problemas aparecen debido a la dificultad en la determinación de las características magnéticas de los cuerpos ferromagnéticos (varillas de histéresis) que se utilizan como amortiguadores de oscilaciones en los satélites. Para estudiar este problema se presenta un modelo analítico que permite estimar la eficiencia del amortiguamiento, y que se ha aplicado al estudio del comportamiento en vuelo de varios satélites, y que se ha empleado para comparar los resultados del modelo con los obtenidos en vuelo, observándose que el modelo permite explicar satisfactoriamente el comportamiento registrado. ABSTRACT The main objective of this thesis is to study the coupling between the attitude control and thermal control subsystems of a small satellite, and address the solution to some existing issues concerning the determination of their parameters. Through the thesis the attitude and temperature evolution of the satellite is studied under the influence of two independent attitude stabilization and control strategies: (1) passive magnetic attitude stabilization (PMAS), and (2) active magnetic attitude control (AMAC). In this regard the mathematical model of the problem is explained and presented. The mathematical model includes both the rotational dynamics and the thermal model. The thermal model is derived for a cubic satellite by solving the heat balance equation for 6 external and 1 internal nodes. Once established the mathematical model of the problem, the above mentioned attitude strategies were applied to the system and the temperature evolution of the 7 nodes of the satellite was studied. The PMAS technique has been selected to be studied due to its prevalent use, simplicity, reliability, and cost, as this strategy significantly saves the overall power, weight, cost, and reduces the complexity of the system compared to other attitude control strategies. In addition to that, another control law that provides the satellite with a desired spin rate along a desired axis of the satellite, whose direction can be controlled with respect to the inertial reference frame is considered, as the thermal subsystem of a satellite usually demands a spin requirement around an axis of the satellite which is positioned perpendicular to the direction of the coming solar radiation. Concerning the thermal problem, to study the influence of spin rate on temperature evolution of the satellite a linear approach of the thermal model is used, which is based on perturbation theory applied to the nonlinear differential equations of the thermal model of a spacecraft moving in a closed orbit. The results of this study showed that the temperature stabilization time and the periodic influence of the external thermal loads decreases by increasing the spin rate. However, the changes become insignificant for higher values of spin rate. Concerning the PMAS strategy, it was observed that in spite of its extended application to micro and nano satellites, still there are some issues to be solved regarding this strategy. These issues are related to the sizing of its system parameters and predicting the in-orbit performance. The problems were found to be rooted in the difficulties that exist in determining the magnetic characteristics of the ferromagnetic bodies (hysteresis rods) that are applied as damping devices on-board satellites. To address these issues an analytic model for estimating their damping efficiency is proposed and applied to several existing satellites in order to compare the results with their respective in-flight data. This model can explain the behavior showed by these satellites.

Algoritmos genéticos en control activo de ruido

Este proyecto se centra en la implementación de un sistema de control activo de ruido mediante algoritmos genéticos. Para ello, se ha tenido en cuenta el tipo de ruido que se quiere cancelar y el diseño del controlador, parte fundamental del sistema de control. El control activo de ruido sólo es eficaz a bajas frecuencias, hasta los 250 Hz, justo para las cuales los elementos pasivos pierden efectividad, y en zonas o recintos de pequeñas dimensiones y conductos. El controlador ha de ser capaz de seguir todas las posibles variaciones del campo acústico que puedan producirse (variaciones de fase, de frecuencia, de amplitud, de funciones de transferencia electro-acústicas, etc.). Su funcionamiento está basado en algoritmos FIR e IIR adaptativos. La elección de un tipo de filtro u otro depende de características tales como linealidad, causalidad y número de coeficientes. Para que la función de transferencia del controlador siga las variaciones que surgen en el entorno acústico de cancelación, tiene que ir variando el valor de los coeficientes del filtro mediante un algoritmo adaptativo. En este proyecto se emplea como algoritmo adaptativo un algoritmo genético, basado en la selección biológica, es decir, simulando el comportamiento evolutivo de los sistemas biológicos. Las simulaciones se han realizado con dos tipos de señales: ruido de carácter aleatorio (banda ancha) y ruido periódico (banda estrecha). En la parte final del proyecto se muestran los resultados obtenidos y las conclusiones al respecto. Summary. This project is focused on the implementation of an active noise control system using genetic algorithms. For that, it has been taken into account the noise type wanted to be canceled and the controller design, a key part of the control system. The active noise control is only effective at low frequencies, up to 250 Hz, for which the passive elements lose effectiveness, and in small areas or enclosures and ducts. The controller must be able to follow all the possible variations of the acoustic field that might be produced (phase, frequency, amplitude, electro-acoustic transfer functions, etc.). It is based on adaptive FIR and IIR algorithms. The choice of a kind of filter or another depends on characteristics like linearity, causality and number of coefficients. Moreover, the transfer function of the controller has to be changing filter coefficients value thought an adaptive algorithm. In this project a genetic algorithm is used as adaptive algorithm, based on biological selection, simulating the evolutionary behavior of biological systems. The simulations have been implemented with two signal types: random noise (broadband) and periodic noise (narrowband). In the final part of the project the results and conclusions are shown.

Sistema de control y visualización de información sobre riesgo de incendios

Una red inalámbrica de sensores (Wireless Sensor Network, WSN) constituye un sistema de comunicación de datos flexible utilizado como alternativa a las redes cableadas o como extensión de éstas. Una de las aplicaciones de estas redes es para su uso en sistemas de predicción y prevención de incendios en áreas naturales. Su implementación se basa en el despliegue de sensores inalámbricos, realizado en una zona de riesgo de incendio que puedan recolectar información tal como temperatura, humedad y presión. Desde una estación base (o nodo "sumidero"), se suministra la información de los sensores a un centro de monitorización y control de forma estructurada. En estos centros la información recibida puede ser analizada, procesada y visualizada en tiempo real. Desde este centro de control se puede controlar también la red WSN modificando el comportamiento de los sensores según el nivel de riesgo de incendio detectado. Este proyecto se basa en el diseño, desarrollo e implementación de un Sistema de Control y Visualización de Información sobre Riesgo de Incendio (SCVIRI), que implementa las funciones de los centros de monitorización y control. La implementación de este sistema, junto con el desarrollado, en paralelo, de otro proyecto denominado Sistema de Estimación de Riesgo de Incendio Utilizando una WSN (SERIUW) que implementa la emulación de la red WSN, conforman un sistema general de anticipación y seguimiento de Fuegos. Se han realizado pruebas de funcionalidad y eficacia, incluidas en la presente memoria del sistema general (ambos proyectos), en un entorno controlado simulado. Este sistema es una solución para la lucha contra los incendios forestales ya que predice y previene, de forma temprana, posibles incendios en las áreas naturales bajo supervisión. Ante un evento de incendio declarado este sistema es un poderoso instrumento de apoyo permitiendo, por un lado, generar alertas automáticas (con localización y gravedad de fuegos detectados) y por el otro, hacer un seguimiento del incendio con mapas en tiempo real (con su consecuente apoyo para la protección e información con las brigadas de bomberos en las zonas activas). ABSTRACT. A wireless sensor network (WSN) is a flexible data communication system used as an alternative to wired networks or as an extension of them. One possible application of these networks is related to fire prediction and prevention in natural areas. Its implementation is based on a deployment of wireless sensors, in an area with high or moderate fire risk, to collect information such as temperature, humidity, luminance and pressure. A base station (or "sink") sends the collected information to a monitoring and control center according to an agreed structured format. At this center, the information received can be analyzed, processed and displayed in real time by using monitoring systems. From this control center the WSN can also be controlled by changing the sensors behavior in consistence with the detected level of fire risk. The work carried out in this project consists on the design, development and implementation of a system named SCVIRI, which implements the functions of the aforementioned monitoring and control center. This system works in connection with other one, called SERIUW, which has been developed in a different project and implements the WSN in an emulated environment. These two systems working together make up a general system of anticipation and monitoring of fires. This document also includes the functionality and performance tests performed on the overall system in a controlled and simulated environment. The global system is a solution that makes it easier to predict and prevent possible fires in natural areas under supervision. This system can be a powerful tool since, before a fire event is declared, it generates automatic alerts (including location and severity information) and allows the real-time motorization of fire evolution and its graphical visualization on maps. This could be also very useful for providing fire brigades with support, protection and information in zones in which a fire is already active.

Development of a fuzzy control based self-adaptive system for energy saving in constrained networks for the Internet of Things

Las redes del futuro, incluyendo las redes de próxima generación, tienen entre sus objetivos de diseño el control sobre el consumo de energía y la conectividad de la red. Estos objetivos cobran especial relevancia cuando hablamos de redes con capacidades limitadas, como es el caso de las redes de sensores inalámbricos (WSN por sus siglas en inglés). Estas redes se caracterizan por estar formadas por dispositivos de baja o muy baja capacidad de proceso y por depender de baterías para su alimentación. Por tanto la optimización de la energía consumida se hace muy importante. Son muchas las propuestas que se han realizado para optimizar el consumo de energía en este tipo de redes. Quizás las más conocidas son las que se basan en la planificación coordinada de periodos de actividad e inactividad, siendo una de las formas más eficaces para extender el tiempo de vida de las baterías. La propuesta que se presenta en este trabajo se basa en el control de la conectividad mediante una aproximación probabilística. La idea subyacente es que se puede esperar que una red mantenga la conectividad si todos sus nodos tienen al menos un número determinado de vecinos. Empleando algún mecanismo que mantenga ese número, se espera que se pueda mantener la conectividad con un consumo energético menor que si se empleara una potencia de transmisión fija que garantizara una conectividad similar. Para que el mecanismo sea eficiente debe tener la menor huella posible en los dispositivos donde se vaya a emplear. Por eso se propone el uso de un sistema auto-adaptativo basado en control mediante lógica borrosa. En este trabajo se ha diseñado e implementado el sistema descrito, y se ha probado en un despliegue real confirmando que efectivamente existen configuraciones posibles que permiten mantener la conectividad ahorrando energía con respecto al uso de una potencia de transmisión fija. ABSTRACT. Among the design goals for future networks, including next generation networks, we can find the energy consumption and the connectivity. These two goals are of special relevance when dealing with constrained networks. That is the case of Wireless Sensors Networks (WSN). These networks consist of devices with low or very low processing capabilities. They also depend on batteries for their operation. Thus energy optimization becomes a very important issue. Several proposals have been made for optimizing the energy consumption in this kind of networks. Perhaps the best known are those based on the coordinated planning of active and sleep intervals. They are indeed one of the most effective ways to extend the lifetime of the batteries. The proposal presented in this work uses a probabilistic approach to control the connectivity of a network. The underlying idea is that it is highly probable that the network will have a good connectivity if all the nodes have a minimum number of neighbors. By using some mechanism to reach that number, we hope that we can preserve the connectivity with a lower energy consumption compared to the required one if a fixed transmission power is used to achieve a similar connectivity. The mechanism must have the smallest footprint possible on the devices being used in order to be efficient. Therefore a fuzzy control based self-adaptive system is proposed. This work includes the design and implementation of the described system. It also has been validated in a real scenario deployment. We have obtained results supporting that there exist configurations where it is possible to get a good connectivity saving energy when compared to the use of a fixed transmission power for a similar connectivity.

A Wireless Charging System Applying Phase-Shift and Amplitude Control to Maximize Efficiency and Extractable Power

Wireless power transfer (WPT) is an emerging technology with an increasing number of potential applications to transfer power from a transmitter to a mobile receiver over a relatively large air gap. However, its widespread application is hampered due to the relatively low efficiency of current Wireless power transfer (WPT) systems. This study presents a concept to maximize the efficiency as well as to increase the amount of extractable power of a WPT system operating in nonresonant operation. The proposed method is based on actively modifying the equivalent secondary-side load impedance by controlling the phase-shift of the active rectifier and its output voltage level. The presented hardware prototype represents a complete wireless charging system, including a dc-dc converter which is used to charge a battery at the output of the system. Experimental results are shown for the proposed concept in comparison to a conventional synchronous rectification approach. The presented optimization method clearly outperforms state-of-the-art solutions in terms of efficiency and extractable power.

Cooperation between the activin and Wnt pathways in the spatial control of organizer gene expression

The normal expression pattern of the Wnt responsive homeobox gene Siamois is restricted to the dorso-vegetal region of the Xenopus embryo. Because the Wnt signaling pathway (via β-catenin) is active on the entire dorsal side of the early embryo, we have asked why Siamois expression is not seen in the dorsal ectoderm. Only Wnt signaling, via activation of β-catenin, can induce directly Siamois, and signaling via the SMAD1 (BMP2/4) or SMAD2 (activin/Vg-1) pathways cannot. We now directly show that the SMAD2 pathway can cooperate with the Wnt pathway to induce expression of Siamois much more strongly than the Wnt pathway alone, in normal embryos. We demonstrate the significance of this cooperation in normal embryos by blocking the SMAD2 signaling pathway with a dominant negative activin receptor. The activin dominant negative receptor blocks this cooperative effect and reduces the expression of Siamois by threefold in early embryos. Furthermore, we find that this cooperative relationship between the SMAD2 and Wnt pathways is reciprocal. Thus, in normal embryos, the Wnt pathway can enhance induction, by the SMAD 2 pathway, of the organizer genes Gsc and Chd but not the pan-mesodermal marker genes Xbra and Eomes. We conclude that the Wnt and SMAD2 signaling pathways cooperate to induce the expression of Spemann-organizer specific genes and so help to localize their spatial expression.

A peptide export–import control circuit modulating bacterial development regulates protein phosphatases of the phosphorelay

The phosphorelay signal transduction system activates developmental transcription in sporulation of Bacillus subtilis by phosphorylation of aspartyl residues of the Spo0F and Spo0A response regulators. The phosphorylation level of these response regulators is determined by the opposing activities of protein kinases and protein aspartate phosphatases that interpret positive and negative signals for development in a signal integration circuit. The RapA protein aspartate phosphatase of the phosphorelay is regulated by a peptide that directly inhibits its activity. This peptide is proteolytically processed from an inactive pre-inhibitor protein encoded in the phrA gene. The pre-inhibitor is cleaved by the protein export apparatus to a putative pro-inhibitor that is further processed to the active inhibitor peptide and internalized by the oligopeptide permease. This export–import circuit is postulated to be a mechanism for timing phosphatase activity where the processing enzymes regulate the rate of formation of the active inhibitor. The processing events may, in turn, be controlled by a regulatory hierarchy. Chromosome sequencing has revealed several other phosphatase–prepeptide gene pairs in B. subtilis, suggesting that the use of this mechanism may be widespread in signal transduction.

Coexpression of factor VIII heavy and light chain adeno-associated viral vectors produces biologically active protein

We are interested in using recombinant adeno-associated viral vectors in the treatment of hemophilia A. Because of the size constraints of recombinant adeno-associated viral vectors, we delivered the heavy and light chains of the human factor 8 (hFVIII) cDNA independently by using two separate vectors. Recombinant AAV vectors were constructed that utilized the human elongation factor 1α promoter, a human growth factor polyadenylation signal, and the cDNA sequences encoding either the heavy or light chain of hFVIII. Portal vein injections of each vector alone, a combination of both vectors, or a hFIX control vector were performed in C57BL/6 mice. An ELISA specific for the light chain of hFVIII demonstrated very high levels (2–10 μg/ml) of protein expression in animals injected with the light chain vector alone or with both vectors. We utilized a chromogenic assay in combination with an antibody specific to hFVIII to determine the amount of biologically active hFVIII in mouse plasma. In animals injected with both the heavy and light chain vectors, greater than physiological levels (200–400 ng/ml) of biologically active hFVIII were produced. This suggests that coexpression of the heavy and light chains of hFVIII may be a feasible approach for treatment of hemophilia A.

Granzymes are the essential downstream effector molecules for the control of primary virus infections by cytolytic leukocytes

Analysis of perforin-deficient mice has identified the cytolytic pathway and perforin as the preeminent effector molecule in T cell-mediated control of virus infections. In this paper, we show that mice lacking both granzyme A (gzmA) and granzyme B (gzmB), which are, beside perforin, key constituents of cytolytic vesicles, are as incapable as are perforin-deficient mice of controlling primary infections by the natural mouse pathogen ectromelia, a poxvirus. Death of gzmA×gzmB double knockout mice occurred in a dose-dependent manner, despite the expression of functionally active perforin and the absence of an intrinsic defect to generate splenic cytolytic T cells. These results establish that both gzmA and gzmB are indispensable effector molecules acting in concert with perforin in granule exocytosis-mediated host defense against natural viral pathogens.