Particle emissions from biodiesels with different physical properties and chemical composition

Biodiesels produced from different feedstocks usually have wide variations in their fatty acid methyl ester (FAME) so that their physical properties and chemical composition are also different. The aim of this study is to investigate the effect of the physical properties and chemical composition of biodiesels on engine exhaust particle emissions. Alongside with neat diesel, four biodiesels with variations in carbon chain length and degree of unsaturation have been used at three blending ratios (B100, B50, B20) in a common rail engine. It is found that particle emission increased with the increase of carbon chain length. However, for similar carbon chain length, particle emissions from biodiesel having relatively high average unsaturation are found to be slightly less than that of low average unsaturation. Particle size is also found to be dependent on fuel type. The fuel or fuel mix responsible for higher particle mass (PM) and particle number (PN) emissions is also found responsible for larger particle median size. Particle emissions reduced consistently with fuel oxygen content regardless of the proportion of biodiesel in the blends, whereas it increased with fuel viscosity and surface tension only for higher diesel–biodiesel blend percentages (B100, B50). However, since fuel oxygen content increases with the decreasing carbon chain length, it is not clear which of these factors drives the lower particle emission. Overall, it is evident from the results presented here that chemical composition of biodiesel is more important than its physical properties in controlling exhaust particle emissions.

Ink-jet printing of graphene for flexible electronics: An environmentally-friendly approach

Mechanical flexibility is considered an asset in consumer electronics and next-generation electronic systems. Printed and flexible electronic devices could be embedded into clothing or other surfaces at home or office or in many products such as low-cost sensors integrated in transparent and flexible surfaces. In this context inks based on graphene and related two-dimensional materials (2DMs) are gaining increasing attention owing to their exceptional (opto)electronic, electrochemical and mechanical properties. The current limitation relies on the use of solvents, providing stable dispersions of graphene and 2DMs and fitting the proper fluidic requirements for printing, which are in general not environmentally benign, and with high boiling point. Non-toxic and low boiling point solvents do not possess the required rheological properties (i.e., surface tension, viscosity and density) for the solution processing of graphene and 2DMs. Such solvents (e.g., water, alcohols) require the addition of stabilizing agents such as polymers or surfactants for the dispersion of graphene and 2DMs, which however unavoidably corrupt their properties, thus preventing their use for the target application. Here, we demonstrate a viable strategy to tune the fluidic properties of water/ethanol mixtures (low-boiling point solvents) to first effectively exfoliate graphite and then disperse graphene flakes to formulate graphene-based inks. We demonstrate that such inks can be used to print conductive stripes (sheet resistance of ~13 kΩ/□) on flexible substrates (polyethylene terephthalate), moving a step forward towards the realization of graphene-based printed electronic devices.

ANKH and susceptibility to and severity of ankylosing spondylitis

Objective. Unconfirmed reports describe association of ankylosing spondylitis (AS) with several candidate genes including ANKH. Cellular export of inorganic pyrophosphate is regulated by the ANK protein, and mutant mice (ank/ank), which have a premature stop codon in the 3′ end of the ank gene, develop severe ankylosis. We tested the association between single-nucleotide polymorphisms (SNP) in these genes and susceptibility to AS in a population of patients with AS. We investigated the role of these genes in terms of functional (BASFI) and metrological (BASMI) measures, and the association with radiological severity (mSASSS). Methods. Our study was conducted on 355 patients with AS and 95 ethnically matched healthy controls. AS was defined according to the modified New York criteria. Four SNP in ANKH (rs27356, rs26307, rs25957, and rs28006) were genotyped. Association analysis was performed using Cochrane-Armitage and linear regression tests for dichotomous and quantitative variables. Analyses of Bath Ankylosing Spondylitis Disease Activity Index (BASDAI), BASFI, and mSASSS were controlled for sex and disease duration. Results. None of the 4 markers showed significant single-locus disease associations (p > 0.05), suggesting that ANKH was not a major determinant of AS susceptibility in our population. No association was observed between these SNP and age at symptom onset, BASDAI, BASFI, BASMI, or mSASSS. Conclusion. These results confirm data in white Europeans that ANKH is probably not a major determinant of susceptibility to AS. ANKH polymorphisms do not markedly influence AS disease severity, as measured by BASMI and mSASSS. The Journal of Rheumatology

Dietary and exercise interventions to improve quality of life, metabolic risk factors and androgen deficiency symptoms in men with prostate cancer undergoing androgen deprivation therapy

Introduction Lifestyle interventions might be useful in the management of adverse effects of androgen deprivation therapy (ADT) in men with prostate cancer. Objectives To examine the effects of dietary and exercise interventions on quality of life (QoL), metabolic risk factors and androgen deficiency symptoms in men with prostate cancer undergoing ADT. Methods CINAHL, Cochrane library, Medline and PsychINFO were searched to identify randomised controlled trials published from January, 2004 to October, 2014. Data extraction and methodological quality assessment was independently conducted by two reviewers. Meta-analysis was conducted using RevMan® 5.3.5. Results Of 2183 articles retrieved, 11 studies met the inclusion criteria and had low risk of bias.Nine studies evaluated exercise (resistance and/or aerobic and/or counselling) and three evaluated dietary supplementation. Median sample size =79 (33–121) and median intervention duration was 12 weeks (12–24). Exercise improved QoL measures (SMD 0.26, 95%CI −0.01 to 0.53) but not body composition, metabolic risk or vasomotor symptoms. Qualitative analysis indicated soy (or isoflavone) supplementation did not improve vasomotor symptoms; however, may improve QoL. Conclusions Few studies have evaluated the efficacy of lifestyle interventions in the management of adverse effects of ADT. We found inconclusive results for exercise in improving QoL and negative results for other outcomes. For soy-based products, we found negative results for modifying vasomotor symptoms and inconclusive results for improving QoL. Future work should investigate the best mode of exercise for improving QoL and other interventions such as dietary counselling should be investigated for their potential to modify these outcomes.

Fine mapping of the MHC Class III region demonstrates association of AIF1 and rheumatoid arthritis

Objective. The heritability of RA has been estimated to be ∼55%, of which the MHC contributes about one-third. HLA-DRB1 alleles are strongly associated with RA, but it is likely that significant non-DRB1 MHC genetic susceptibility factors are involved. Previously, we identified two three-marker haplotypes in a 106-kb region in the MHC class III region immediately centromeric to TNF, which are strongly associated with RA on HLA-DRB1*0404 haplotypes. In the present study, we aimed to refine these associations further using a combination of genotyping and gene expression studies. Methods. Thirty-nine nucleotide polymorphisms (SNPs) were genotyped in 95 DRB1*0404 carrying unrelated RA cases, 125 DRB1*0404 - carrying healthy controls and 87 parent-case trio RA families in which the affected child carried HLA-DRB1*04. Quantitative RT-PCR was used to assess the expression of the positional candidate MHC class III genes APOM, BAT2, BAT3, BAT4, BAT5, AIF1, C6orf47, CSNK2β and LY6G5C, and the housekeeper genes, hypoxanthine-guanine phosphoribosyltransferase (HPRT) and β2-microglobulin (B2M) in 31 RA cases and 21 ethnically, age- and sex-matched healthy controls. Synovial membrane specimens from RA, PsA and OA cases were stained by an indirect immunoperoxidase technique using a mouse-anti-human AIF1 monoclonal antibody. Results. Association was observed between RA and single markers or two marker haplotypes involving AIF1, BAT3 and CSNK. AIF1 was also significantly overexpressed in RA mononuclear cells (1.5- to 1.9-fold difference, P = 0.02 vs HPRT, P = 0.002 vs B2M). AIF1 protein was clearly expressed by synovial macrophages in all the inflammatory synovial samples in contrast to the non-inflammatory OA samples. Conclusions. The results of the genotyping and expression studies presented here suggest a role for AIF1 in both the aetiology and pathogenesis of RA.

Fate of swallowed interleukin 8 and TNFα, and effect on the Wistar rat gut

To evaluate the passage of cytokines through the gastrointestinal tract, we investigated the digestion of interleukin-8 (IL-8) and tumour necrosis factor α (TNFα), in vitro and in vivo, and their propensity to induce intestinal inflammation. We serially immuno-assayed IL-8 and TNFα solutions co-incubated with each of three pancreatin preparations at pH 4.5 and pH 8. We gavaged IL-8, TNFα and marker into 15 Wistar rats, and measured their faecal cytokine concentrations by ELISA and histologically examined their guts. IL-8 immunoreactivity was extinguished by all pancreatin preparations after 1 h of incubation at 37 °C. TNFα concentration progressively fell from 1 to 4 h with all enzyme preparations. Buffer control samples maintained their cytokine concentrations throughout incubation. No IL-8 or TNFα was detected in any rat faecal pellets. There was no significant proinflammatory effect of the gavaged cytokines on rat intestine. IL-8 and TNFα in aqueous solution could well be fully digested in the CF gut when transit time is normal and exogenous enzymes are provided, although cytokines swallowed in viscous sputum may be protected from such digestion

Mixed convection in non-Newtonian fluids along a vertical plate in a porous medium

The problem of mixed convection from vertical surfaces in a porous medium saturated with a power-law type non-Newtonian fluid is investigated. The transformed conservation laws are solved numerically for the case of variable wall temperature conditions. Results for the details of the velocity and temperature fields as well as the Nusselt number have been presented. The viscosity index ranged from 0.5-2.0.

Dynamics of a dilute sheared inelastic fluid. II. The effect of correlations

The effect of correlations on the viscosity of a dilute sheared inelastic fluid is analyzed using the ring-kinetic equation for the two-particle correlation function. The leading-order contribution to the stress in an expansion in epsilon=(1-e)(1/2) is calculated, and it is shown that the leading-order viscosity is identical to that obtained from the Green-Kubo formula, provided the stress autocorrelation function in a sheared steady state is used in the Green-Kubo formula. A systemmatic extension of this to higher orders is also formulated, and the higher-order contributions to the stress from the ring-kinetic equation are determined in terms of the terms in the Chapman-Enskog solution for the Boltzmann equation. The series is resummed analytically to obtain a renormalized stress equation. The most dominant contributions to the two-particle correlation function are products of the eigenvectors of the conserved hydrodynamic modes of the two correlated particles. In Part I, it was shown that the long-time tails of the velocity autocorrelation function are not present in a sheared fluid. Using those results, we show that correlations do not cause a divergence in the transport coefficients; the viscosity is not divergent in two dimensions, and the Burnett coefficients are not divergent in three dimensions. The equations for three-particle and higher correlations are analyzed diagrammatically. It is found that the contributions due to the three-particle and higher correlation functions to the renormalized viscosity are smaller than those due to the two-particle distribution function in the limit epsilon -> 0. This implies that the most dominant correlation effects are due to the two-particle correlations.

Rheology of particle-loaded semi-dilute polymer solutions

We present measurements of the rheology of suspensions of rigid spheres in a semi-dilute polymer solution from experiments of steady and oscillatory shear. For a given value of the shear rate gamma, addition of particles enhances the viscosity and the first normal stress difference but decreases the magnitude of the second normal stress difference. The viscosity eta exhibits a power law variation in gamma for a range of gamma that grows with phi. The first normal stress N-1 is positive and its value grows with phi; it exhibits a clear power law variation for the entire range of gamma that was studied. The second normal stress difference N-2 is negative for the pure polymer solution and much smaller in magnitude than N-1; on addition of particles, its magnitude further decreases, and it appears to change sign at large phi. The behavior of N-1 and N-2 is at odds with the findings of recent studies on particle-loaded dilute polymer solutions and polymer melts. The small-amplitude oscillatory shear experiments show the linear viscoelastic properties, G(') and G('), increasing with phi at a given value of the angular frequency omega. The dynamic viscosity of the suspension differs substantially from its steady shear viscosity, and the difference increases as gamma, omega -> 0.

Axially Loaded Timoshenko Rotors From A Prestressed Continuum Approach

We consider an axially loaded Timoshenko rotor rotating at a constant speed and derive its governing equations from a continuum viewpoint. The primary aim of this paper is to understand the source and role of gyroscopic terms, when the rotor is viewed not as a Timoshenko beam but as a genuine 3D continuum. We offer the primary insight that macroscopically observed gyroscopic terms may also, quite equivalently, be viewed as external manifestations of internally existing spin-induced prestresses at the continuum level. To demonstrate this idea with an analytical example (the Timoshenko rotor), we have studied the reliable equations of Choi et al. (Journal of Vibration and Acoustics, 114, 1992, 249-259). Using a straightforward application of our insight in the framework of nonlinear elasticity, we obtain equations that exactly match Choi et al. for the case with no axial load. For the case of axial preload, our straightforward formulation leads to a slightly different set of equations that have negligible numerical consequence for solid rotors. However, we offer a macroscopic, intuitive, justification for modifying our formulation so as to obtain the exact equations of Choi et al. with the axial load included.

Flow behavior of LDPE and its blends with LLDPE I and II: A comparative study

Studies on melt rheological properties of blends of low density polyethylene (LDPE) with selected grades of linear low density polyethylene (LLDPE), which differ widely in their melt flow indices, are reported, The data obtained in a capillary rheometer are presented to describe the effects of blend composition and shear rate on flow behavior index, melt viscosity, and melt elasticity. In general, blending of LLDPE I that has a low melt flow index (2 g/10 min) with LDPE results in a decrease of its melt viscosity, processing temperature, and the tendency of extrudate distortion, depending on blending ratio. A blending ratio around 20-30% LLDPE I seems optimum from the point of view of desirable improvement in processability behavior. On the other hand, blending of LLDPE II that has a high melt flow index (10 g/10 min) with LDPE offers a distinct advantage in increasing the pseudoplasticity of LDPE/LLDPE II blends.

2.5-dimensional solution of the advective accretion disk:a self-similar approach

We provide a 2.5-dimensional solution to a complete set of viscous hydrodynamical equations describing accretion- induced outflows and plausible jets around black holes/compact objects. We prescribe a self-consistent advective disk-outflow coupling model, which explicitly includes the information of vertical flux. Inter-connecting dynamics of an inflow-outflow system essentially upholds the conservation laws. We provide a set of analytical family of solutions through a self-similar approach. The flow parameters of the disk-outflow system depend strongly on the viscosity parameter α and the cooling factor.

Differential Games of Mixed Type with Control and Stopping Times

We study a zero sum differential game of mixed type where each player uses both control and stopping times. Under certain conditions we show that the value function for this problem exists and is the unique viscosity solution of the corresponding variational inequalities. We also show the existence of saddle point equilibrium for a special case of differential game.

Fluidity of mica particle dispersed aluminium alloy

Cast aluminium alloy-mica particle composites were made by dispersing mica particles in a vortex produced by stirring the liquid Al-4 wt% Cu-1.5 wt% Mg alloy and then casting the melt containing the suspended particles into permanent moulds. Spiral fluidity and casting fluidity of the alloy containing mica particles in suspension were determined. Both the spiral fluidity and the casting fluidity of the base alloy were found to decrease with an increase in volume or weight percent of mica particles (of a given size), and with a decrease in particle size (for a given amount of particles). The fluidities of Al-4 wt% Cu-1.5 wt% Mg alloys containing suspended mica particles were found to correlate very well with the surface area of suspended mica particles. The regression equation for spiral fluidity Y (cm) as a function of surface area of mica particles per gram of spiral X (cm2 g–1) at 700° C was found to be Y=42.62–0.42X with a correlation coefficient of 0.9634. The regression equations for casting fluidity Yprime (cm) as a functiono of surface area of mica particles per gram of fluidity test piece Xprime (cm2 g–1) at 710 and 670° C were found to be Yprime=19.71–0.17Xprime and Yprime=13.52–0.105Xprime with correlation coefficients of 0.9194 and 0.9612 respectively. The percentage decrease in casting fluidity of composite melts containing up to 2.5 wt% mica with a drop in temperature is quite similar to the corresponding decrease in the casting fluidity of base alloy melts (without mica). The change in fluidity due to mica dispersions has been discussed in terms of changes in viscosity of the composite melts. However, the fluidities of these composite alloys containing up to 2.5 wt% mica are adequate for making a variety of simple castings including bearings for which these alloys have been developed.

Compressible boundary-layer flow at a three-dimensional stagnation point with massive blowing

The effect of massive blowing rates on the steady laminar compressible boundary-layer flow with variable gas properties at a 3-dim. stagnation point (which includes both nodal and saddle points of attachment) has been studied. The equations governing the flow have been solved numerically using an implicit finite-difference scheme in combination with the quasilinearization technique for nodal points of attachment but employing a parametric differentiation technique instead of quasilinearization for saddle points of attachment. It is found that the effect of massive blowing rates is to move the viscous layer away from the surface. The effect of the variation of the density- viscosity product across the boundary layer is found to be negligible for massive blowing rates but significant for moderate blowing rates. The velocity profiles in the transverse direction for saddle points of attachment in the presence of massive blowing show both the reverse flow as well as velocity overshoot.