Modelling of water removal during a paper vacuum dewatering process using a Level-Set method

Water removal in paper manufacturing is an energy-intensive process. The dewatering process generally consists of four stages of which the first three stages include mechanical water removal through gravity filtration, vacuum dewatering and wet pressing. In the fourth stage, water is removed thermally, which is the most expensive stage in terms of energy use. In order to analyse water removal during a vacuum dewatering process, a numerical model was created by using a Level-Set method. Various different 2D structures of the paper model were created in MATLAB code with randomly positioned circular fibres with identical orientation. The model considers the influence of the forming fabric which supports the paper sheet during the dewatering process, by using volume forces to represent flow resistance in the momentum equation. The models were used to estimate the dry content of the porous structure for various dwell times. The relation between dry content and dwell time was compared to laboratory data for paper sheets with basis weights of 20 and 50 g/m2 exposed to vacuum levels between 20 kPa and 60 kPa. The comparison showed reasonable results for dewatering and air flow rates. The random positioning of the fibres influences the dewatering rate slightly. In order to achieve more accurate comparisons, the random orientation of the fibres needs to be considered, as well as the deformation and displacement of the fibres during the dewatering process.

Vacuum-assisted closure treatment of leg skin necrosis after angiographic embolization of a giant plexiform neurofibroma

Type 1 neurofibromatosis is a relatively common inherited disease of the nervous system, with a frequency of almost 1 in 3000. It is associated with neurofibromas of various sites. Our case report is about the surgical management of a giant neurofibroma of the right gluteal fold in a 46-year-old male with NF1. The patient presented with increasing edema and accelerated growth of the mass; he underwent percutaneous embolization of lesion vessels that induced necrosis of the neurofibroma. The patient was taken to the operating room, where surgical resection of the bulk of the lesion was undertaken. The postoperative course was complicated by delayed wound closure managed with antibiotics and vacuum-assisted wound closure. Giant neurofibromas similar to this tumor require complex preoperative, intraoperative and postoperative management strategies. Surgical debulk is best managed with preoperative percutaneous embolization that help to avoid surgical bleeding. Postoperative delayed wound closure was managed with the application of negative pressure in a closed environment that triggers granulation and tissue formation.

Evaluation of negative pressure vacuum-assisted system in acute and chronic wounds closure. Our experience

Negative-pressure therapy or vacuum-assisted closure (VAC) has been used in clinical applications since the 1940’s and has increased in popularity over the past decade. This dressing technique consists of an open cell foam dressing put into the wound cavity, a vacuum pump produces a negative pressure and an adhesive drape. A controlled sub atmospheric pressure from 75 to 150 mmHg is applied. The vacuum-assisted closure has been applied by many clinicians to chronic wounds in humans; however it cannot be used as a replacement for surgical debridement. The initial treatment for every contaminated wound should be the necrosectomy. The VAC therapy has a complementary function and the range of its indications includes pressure sores, stasis ulcers, chronic wounds such as diabetic foot ulcers, post traumatic and post operative wounds, infected wounds such as necrotizing fasciitis or sternal wounds, soft-tissue injuries, bone exposed injuries, abdominal open wounds and for securing a skin graft. We describe our experience with the VAC dressing used to manage acute and chronic wounds in a series of 135 patients, with excellent results together with satisfaction of the patients.

Advanced Adhesion Strength Testing Methods of Thin Film Multilayers in Electronic Packaging Systems

With the continued miniaturization and increasing performance of electronic devices, new technical challenges have arisen. One such issue is delamination occurring at critical interfaces inside the device. This major reliability issue can occur during the manufacturing process or during normal use of the device. Proper evaluation of the adhesion strength of critical interfaces early in the product development cycle can help reduce reliability issues and time-to-market of the product. However, conventional adhesion strength testing is inherently limited in the face of package miniaturization, which brings about further technical challenges to quantify design integrity and reliability. Although there are many different interfaces in today's advanced electronic packages, they can be generalized into two main categories: 1) rigid to rigid connections with a thin flexible polymeric layer in between, or 2) a thin film membrane on a rigid structure. Knowing that every technique has its own advantages and disadvantages, multiple testing methods must be enhanced and developed to be able to accommodate all the interfaces encountered for emerging electronic packaging technologies. For evaluating the adhesion strength of high adhesion strength interfaces in thin multilayer structures a novel adhesion test configuration called “single cantilever adhesion test (SCAT)” is proposed and implemented for an epoxy molding compound (EMC) and photo solder resist (PSR) interface. The test method is then shown to be capable of comparing and selecting the stronger of two potential EMC/PSR material sets. Additionally, a theoretical approach for establishing the applicable testing domain for a four-point bending test method was presented. For evaluating polymeric films on rigid substrates, major testing challenges are encountered for reducing testing scatter and for factoring in the potentially degrading effect of environmental conditioning on the material properties of the film. An advanced blister test with predefined area test method was developed that considers an elasto-plastic analytical solution and implemented for a conformal coating used to prevent tin whisker growth. The advanced blister testing with predefined area test method was then extended by employing a numerical method for evaluating the adhesion strength when the polymer’s film properties are unknown.

Avaliação da anchoita (engraulis anchoita) salgada maturada acondicionada em atmosfera modificada

A anchoita foi capturada e acondicionada a bordo sob-resfriamento a 0°C com gelo em escamas. Após o recebimento, o pescado foi processado na forma salgado-maturado. Após a maturação foram processadas e embaladas em sacos de polietileno e armazenadas sob-refrigeração a 5°C durante 84 dias. As amostras foram divididas grupos: (1) sob pressão atmosfera normal, (2) vácuo, (3) atmosfera modificada com 50% CO2 + 20% O2 + 30% N2 e (4) 60% CO2 + 10% O2 + 30% N2, em embalagens de polietileno e aluminizadas, termo-seladas e armazenadas sob-refrigeração a 5°C. Os valores de textura tiveram uma redução de 2277,8 N (Kg.m/s2 ) para 821,90 N (Kg.m/s2 ) para o tratamento controle. A qualidade inicial do pescado atendeu aos padrões legais vigentes, apresentando ausência Salmonella sp e enumerações aceitáveis aos padrões de Staphylococcus coagulase positiva, Clostridium sulfito redutores, coliforme totais e a 45ºC. Com relação ao pH, houve diferenças significativas durante o tempo de processamento (p<0,05), o valor passou de 6,3 (início) para 6,4 (final). Com relação aos resultados correspondentes aos parâmetros L*, a* e b* (cor), em todos os tratamentos e ao longo do tempo de processamento (ambas as embalagens), ocorreram diferenças significativas (p<0,05). Os valores de L* variaram de 34,80 para 18,00 (controle) 23,00 (vácuo), 20,21 (T3) e 22,00 (T4) embalagens de polietileno. Nas embalagens de alumínio os valores de L* variaram de 34,00 para 25,00 (controle), 29,00(vácuo), 22,10 (T3) e 26,00 (T4).

Modified atmosphere packaging effects on the postharvest quality of papaya fruit

Export of Fijian papaya (Carica papaya) fruit to destinations such as New Zealand has increased significantly over the last several years. Shipment by sea rather than air is the preferred method, given the capacity for larger volumes and reductions in cost. Long shipping times, however, can compromise fruit quality, although the use of modified atmosphere packaging (MAP) may provide a viable solution for extending fruit storage life. In a collaborative ACIAR project, Australian and Fijian researchers investigated the potential of using MAP to extend storage life of a Fijian papaya ('Fiji Red') fruit based on simulated sea transport conditions. Fruit were packed in one of three MAP environments within cartons, consisting of either a (1) Low Density Polyethylene (LDPE) bag with 10 g of KMnO4, (2) Polyamide Film (PF) bag with macro-perforations or (3) without a bag (control fruit). Fruit were held for 1, 2 or 3 weeks at 10°C before being unpacked, ripened and assessed for quality. On day 6 after outturn, fruit with the highest overall quality were those held in LDPE bags. LDPE fruit generally coloured up faster at outturn than PF or control fruit, had less overall moisture loss and scored high in flavour. Headspace carbon dioxide and oxygen concentrations within the LDPE bags were also near recommended levels for maintaining optimum storage-life quality. The LDPE bag provided the most suitable conditions for long term storage of fresh papaya fruit and is therefore the recommended MAP type for use with sea freight export out of Fiji.

THERMAL VACUUM TEST CORRELATION OF A ZERO PROPELLANT LOAD CASE THERMAL CAPACITANCE PROPELLANT GAUGING ANALYTICAL MODEL

This thesis describes the development and correlation of a thermal model that forms the foundation of a thermal capacitance spacecraft propellant load estimator. Specific details of creating the thermal model for the diaphragm propellant tank used on NASA’s Magnetospheric Multiscale spacecraft using ANSYS and the correlation process implemented are presented. The thermal model was correlated to within +/- 3 Celsius of the thermal vacuum test data, and was determined sufficient to make future propellant predictions on MMS. The model was also found to be relatively sensitive to uncertainties in applied heat flux and mass knowledge of the tank. More work is needed to improve temperature predictions in the upper hemisphere of the propellant tank where predictions were found to be 2-2.5 Celsius lower than the test data. A road map for applying the model to predict propellant loads on the actual MMS spacecraft in 2017-2018 is also presented.

Electronic Packaging of Paper-Based Anisotropic Magnetoresistive Sensors

This report investigates adaptations of electronic packaging methods used to create stacks of these sensors. Four methods were developed and tested to determine the best option in terms of mechanical stability and electrical conductivity of the system. For the first method, a stack is created by way of through paper vias (TPVs), a hole that is cut in the pads of the sensors and then filled with electrically conductive adhesive through the openings on the two sensors to be joined. The second method is called mechanical caulking and connects sensors through pads which have been lined with copper tape backed with conductive adhesive. The connection is created with a small copper rivet which is flattened in place by compressive force. The third method is the stitching method which is inspired by sewing of fabric. A pattern of thin copper wire is stitched on the pad of a sensor that is lined with copper tape backed with conductive adhesive. The wire is then stitched through a second sensor that is treated similarly with copper tape and the stack receives the same pattern through the two layers as was applied to the first sensor alone. The final method is the collapsed daisy chain which is the linear connection of sensors to their neighboring sensors via copper tape backed with conductive adhesive. The row of sensors is then collapsed in an alternating orientation into a single stack.

Advanced parametrical modelling of 24 GHz radar sensor IC packaging components

This paper deals with the development of an advanced parametrical modelling concept for packaging components of a 24 GHz radar sensor IC used in automotive driver assistance systems. For fast and efficient design of packages for system-in-package modules (SiP), a simplified model for the description of parasitic electromagnetic effects within the package is desirable, as 3-D field computation becomes inefficient due to the high density of conductive elements of the various signal paths in the package. By using lumped element models for the characterization of the conductive components, a fast indication of the design's signal-quality can be gained, but so far does not offer enough flexibility to cover the whole range of geometric arrangements of signal paths in a contemporary package. This work pursues to meet the challenge of developing a flexible and fast package modelling concept by defining parametric lumped-element models for all basic signal path components, e.g. bond wires, vias, strip lines, bumps and balls. © Author(s) 2011. CC Attribution 3.0 License.

Evaluation of the Genotoxicity of Chitosan Nanoparticles for Use in Food Packaging Films

The use of nanoparticles in food packaging has been proposed on the basis that it could improve protection of foods by, for example, reducing permeation of gases, minimizing odor loss, and increasing mechanical strength and thermal stability. Consequently, the impacts of such nanoparticles on organisms and on the environment need to be investigated to ensure their safe use. In an earlier study, Moura and others (2008a) described the effect of addition of chitosan (CS) and poly(methacrylic acid) (PMAA) nanoparticles on the mechanical properties, water vapor, and oxygen permeability of hydroxypropyl methylcellulose films used in food packaging. Here, the genotoxicity of different polymeric CS/PMAA nanoparticles (size 60, 82, and 111 nm) was evaluated at different concentration levels, using the Allium cepa chromosome damage test as well as cytogenetic tests employing human lymphocyte cultures. Test substrates were exposed to solutions containing nanoparticles at polymer mass concentrations of 1.8, 18, and 180 mg/L. Results showed no evidence of DNA damage caused by the nanoparticles (no significant numerical or structural changes were observed), however the 82 and 111 nm nanoparticles reduced mitotic index values at the highest concentration tested (180 mg/L), indicating that the nanoparticles were toxic to the cells used at this concentration. In the case of the 60 nm CS/PMAA nanoparticles, no significant changes in the mitotic index were observed at the concentration levels tested, indicating that these particles were not toxic. The techniques used show promising potential for application in tests of nanoparticle safety envisaging the future use of these materials in food packaging.

Packaging as a vehicle of nutritional information for children: Enhancing children’s perceptions of healthy food

Field lab in marketing: Children consumer behaviour

Evading Vacuum Noise: Wigner Projections or Husimi Samples?

The accuracy in determining the quantum state of a system depends on the type of measurement performed. Homodyne and heterodyne detection are the two main schemes in continuous-variable quantum information. The former leads to a direct reconstruction of the Wigner function of the state, whereas the latter samples its Husimi Q function. We experimentally demonstrate that heterodyne detection outperforms homodyne detection for almost all Gaussian states, the details of which depend on the squeezing strength and thermal noise.

Packaging and Deployment of Large Planar Spacecraft Structures

This thesis presents a set of novel methods to biaxially package planar structures by folding and wrapping. The structure is divided into strips connected by folds that can slip during wrapping to accommodate material thickness. These packaging schemes are highly efficient, with theoretical packaging efficiencies approaching 100%. Packaging tests on meter-scale physical models have demonstrated packaging efficiencies of up to 83%. These methods avoid permanent deformation of the structure, allowing an initially flat structure to be deployed to a flat state.

Also presented are structural architectures and deployment schemes that are compatible with these packaging methods. These structural architectures use either in-plane pretension -- suitable for membrane structures -- or out-of-plane bending stiffness to resist loading. Physical models are constructed to realize these structural architectures. The deployment of these types of structures is shown to be controllable and repeatable by conducting experiments on lab-scale models.

These packaging methods, structural architectures, and deployment schemes are applicable to a variety of spacecraft structures such as solar power arrays, solar sails, antenna arrays, and drag sails; they have the potential to enable larger variants of these structures while reducing the packaging volume required. In this thesis, these methods are applied to the preliminary structural design of a space solar power satellite. This deployable spacecraft, measuring 60 m x 60 m, can be packaged into a cylinder measuring 1.5 m in height and 1 m in diameter. It can be deployed to a flat configuration, where it acts as a stiff lightweight support framework for multifunctional tiles that collect sunlight, generate electric power, and transmit it to a ground station on Earth.

Pirólise de borras oleosas de petroleo utilizando nanomateriais

The oily sludge is a complex mix of hydrocarbons, organic impurities, inorganic and water. One of the major problems currently found in petroleum industry is management (packaging, storage, transport and fate) of waste. The nanomaterials (catalysts) mesoporous and microporous are considered promising for refining and adsorbents process for environment protection. The aim of this work was to study the oily sludge from primary processing (raw and treated) and vacuum residue, with application of thermal analyses technique (pyrolysis), thermal and catalytic pyrolysis with nanomaterials, aiming at production petroleum derived. The sludge and vacuum residue were analyzed using a soxhlet extraction system, elemental analysis, thin layer chromatography, thermogravimetry and pyrolysis coupled in gas chromatography/mass spectrometry (Py GC MS). The catalysts AlMCM-41, AlSBA-15.1 e AlSBA-15.2 were synthesized with molar ratio silicon aluminum of 50 (Si/Al = 50), using tetraethylorthosilicante as source of silicon and pseudobuhemita (AlOOH) as source of aluminum. The analyzes of the catalysts indicate that materials showed hexagonal structure and surface area (783,6 m2/g for AlMCM-41, 600 m2/g for AlSBA-15.1, 377 m2/g for AlSBA-15.2). The extracted oily sludge showed a range 65 to 95% for organic components (oil), 5 to 35% for inorganic components (salts and oxides) and compositions different of derivatives. The AlSBA-15 catalysts showed better performance in analyzes for production petroleum derived, 20% increase in production of kerosene and light gas oil. The energy potential of sludge was high and it can be used as fuel in other cargo processed in refinery