Competence Training in Higher Education: The case of the Technological Master "Prestación de Servicios Profesionales" from the Colegio de Postgraduados (México).

The Competency-Based Education in the context of training is intended as a comprehensive approach that seeks to link education with the productive sector and increase the potential of individuals, in the face of social, economic, political and cultural transformations that suffers the world and the contemporary society; this is how educational services associated to the rural area takes part of the global revalorization of the role of learning and knowledge. Under the competence approach and taking into account the CONOCER model, we design a Technological Master from the “Colegio de Postgraduados” identifying the competences needed so that the students, professional from different areas of knowledge, managed to develop them, but mainly to achieve the goal of developing the capacities of producers in Mexican rural area.

Si(100) versus Ge(100): Watching the interface formation for the growth of III-V-based solar cells on abundant substrates

We investigated the atomic surface properties of differently prepared silicon and germanium (100) surfaces during metal-organic vapour phase epitaxy/chemical vapour deposition (MOVPE/MOCVD), in particular the impact of the MOVPE ambient, and applied reflectance anisotropy/difference spectroscopy (RAS/RDS) in our MOVPE reactor to in-situ watch and control the preparation on the atomic length scale for subsequent III-V-nucleation. The technological interest in the predominant opto-electronic properties of III-V-compounds drives the research for their heteroepitaxial integration on more abundant and cheaper standard substrates such as Si(100) or Ge(100). In these cases, a general task must be accomplished successfully, i.e. the growth of polar materials on non-polar substrates and, beyond that, very specific variations such as the individual interface formation and the atomic step structure, have to be controlled. Above all, the method of choice to grow industrial relevant high-performance device structures is MOVPE, not normally compatible with surface and interface sensitive characterization tools, which are commonly based on ultrahigh vacuum (UHV) ambients. A dedicated sample transfer system from MOVPE environment to UHV enabled us to benchmark the optical in-situ spectra with results from various surfaces science instruments without considering disruptive contaminants. X-ray photoelectron spectroscopy (XPS) provided direct observation of different terminations such as arsenic and phosphorous and verified oxide removal under various specific process parameters. Absorption lines in Fourier-transform infrared (FTIR) spectra were used to identify specific stretch modes of coupled hydrides and the polarization dependence of the anti-symmetric stretch modes distinguished different dimer orientations. Scanning tunnelling microscopy (STM) studied the atomic arrangement of dimers and steps and tip-induced H-desorption proved the saturation of dangling bonds after preparati- n. In-situ RAS was employed to display details transiently such as the presence of H on the surface at lower temperatures (T <; 800°C) and the absence of Si-H bonds at elevated annealing temperature and also surface terminations. Ge buffer growth by the use of GeH4 enables the preparation of smooth surfaces and leads to a more pronounced amplitude of the features in the spectra which indicates improvements of the surface quality.

Towards a Transfer Model of Scientific and Technological Knowledge: the Case of Mexico

This paper shows the development of a science-technological knowledge transfer model in Mexico, as a means to boost the limited relations between the scientific and industrial environments. The proposal is based on the analysis of eight organizations (research centers and firms) with varying degrees of skill in the practice of science-technological knowledge transfer, and carried out by the case study approach. The analysis highlights the synergistic use of the organizational and technological capabilities of each organization, as a means to identification of the knowledge transfer mechanisms best suited to enabling the establishment of cooperative processes, and achieve the R&D and innovation activities results.

An Analysis of the Influence of Students´ Technological Culture on Their Technology

decade has raised the interest among the research community on the acceptance and use of these systems by both teachers and students. At first, the implementation of LMS was based on their technical design and the adaptation of the learning processes to the virtual environment, neglecting students’ characteristics when the systems were deployed, which led to expensive and failing implementations. The Unified Theory of Acceptance and Use of Technology (UTAUT) proposes a framework which allows the study of the acceptance and use of technology that takes into consideration the students’ characteristics and how they affect the acceptance and the degree of use of educational technology. This study questions the role of the user’s attitude towards use of LMS and uses the UTAUT to examine the moderating effect of technological culture in the adoption of LMS in Spain. The results from the comparison and analysis of three different models confirm the relevance of attitude towards use as an antecedent of intention to use the system, as well as the important moderating effect of gender and technological culture. The discussion of results suggests the need for a more in-depth analysis and interrelations of cultural dimensions in the adoption of educational technologies and learning management systems

Precision Agriculture without borders: Practical issues and improvements in farmland coverage with aerial vehicles.

This work presents a solution for the aerial coverage of a field by using a fleet of aerial vehicles. The use of Unmanned Aerial Vehicles allows to obtain high resolution mosaics to be used in Precision Agriculture techniques. This report is focus on providing a solution for the full simultaneous coverage problem taking into account restrictions as the required spatial resolution and overlap while maintaining similar light conditions and safety operation of the drones. Results obtained from real field tests are finally reported

Some improvements over the continuation call tabling implementation technique

Tabled evaluation has been proved an effective method to improve several aspeets of goal-oriented query evaluation, including termination and complexity. Several "native" implementations of tabled evaluation have been developed which offer good performance, but many of them need significant changes to the underlying Prolog implementation. More portable approaches, generally using program transformation, have been proposed but they often result in lower efficieney. We explore some techniques aimed at combining the best of these worlds, i.e., developing a portable and extensible implementation, with minimal modifications at the abstract machine level, and with reasonably good performance. Our preliminary results indícate promising results.

Modelización de contactos termoelastohidrodinámicos

La mejora en la eficiencia energética y la reducción de la tasa de fallos en los contactos lubricados son aspectos que resultan de gran interés en numerosos sectores de la industria, y plantean en estos momentos nuevas dificultades operativas y retos para un futuro próximo. Los avances tecnológicos han incrementado las exigencias técnicas que se requieren a los aceites para cumplir su función al extender sus variables operativas a un mayor espectro de aplicaciones, tanto de condiciones de funcionamiento como a la gran variedad de nuevos materiales constitutivos de los engranajes en los que se tiene que utilizar. Por ello, actualmente se está incentivado el desarrollo de nuevos procedimientos que permitan comprender el comportamiento de este tipo de contactos lubricados, con el fin de lograr mejoras técnicas en su diseño y la correcta selección del aceite. En esta Tesis Doctoral se presenta una metodología de cálculo numérico que permite simular el comportamiento de contactos elastohidrodinámicos (EHD) puntuales, como puede ser el caso de un rodamiento. La resolución de este problema presenta diversas complejidades matemáticas y exige el desarrollo de un elaborado procedimiento de cálculo basado en técnicas multinivel. Para hacer del procedimiento una herramienta válida en un gran número de condiciones de funcionamiento y tipos de lubricantes, se ha tenido en cuenta en el cálculo la posible aparición de comportamientos no-Newtonianos del lubricante y fenómenos de generación y disipación de calor, provocados por el movimiento relativo del fluido y las superficies en contacto. Para la validación del procedimiento, se han contrastado los resultados numéricos obtenidos con nuestro método, con los resultados numéricos y experimentales publicados por otros autores y con valores experimentales propios medidos en un equipo de ensayo de contacto puntual tipo MTM. El desarrollo de este programa ha dotado a la División de Ingeniería de Máquinas de una herramienta que ha permitido, y sobre todo va permitir, evaluar la importancia de cada uno de los parámetros reológicos en los diferentes problemas que va a tener que abordar, evaluación que hasta el momento se realizaba con métodos aproximados que describen la fenomenología con mucha menos precisión. A la hora de emplear nuestro procedimiento numérico para simular situaciones reales, nos hemos encontrado con el obstáculo de que es muy complicado encontrar, en la bibliografía y bases de datos, los parámetros que caracterizan el comportamiento reológico del lubricante en las condiciones de presión, temperatura y grado de cizallamiento habituales en las que se trabaja en este tipo de contactos, y las pocas medidas que existen para estas condiciones de funcionamiento son poco fiables. Por ello como complemento al objetivo principal de esta Tesis hemos desarrollado una metodología para caracterizar los lubricantes en estas condiciones extremas. Dicha metodología está basada en la buena descripción que hace nuestro programa del coeficiente de fricción, lo que nos ha permitido obtener los parámetros reológicos del III lubricante a partir de las medidas experimentales del coeficiente de fricción generado en un equipo MTM lubricado con el lubricante que se desea caracterizar. Madrid, Octubre de 2012 IV Improving energy efficiency and reducing the failure rate in lubricated contacts are issues that are of great interest in many sectors of industry, and right now posed operational difficulties and new challenges for the near future. Technological advances have increased the technical demands required to oils to fulfil its role by extending its operational variables to a wider range of applications, both operating conditions and to the wide variety of new materials which constitute the gear in which must be used. For this reason, has being encouraged currently to develop new procedures to understand the behaviour of this type of lubricated contacts, in order to achieve improvements in design techniques and the correct oil selection. In this Thesis we present a numerical methodology to simulate the puntual elastohydrodynamic contact behaviour (EHD), such as a roller bearing. The resolution of this problem presents various mathematical complexities and requires the development of an elaborate calculation procedure based on multilevel techniques. To make the procedure a valid tool in a wide range of operating conditions and types of lubricants, has been taken into account in calculating the possible occurrence of non-Newtonian behaviour of the lubricant and phenomena of generation and dissipation of heat, caused by the fluid relative motion and contacting surfaces. For the validation of the method, we have compared the numerical results obtained with our method with numerical and experimental results published by other authors also with own experimental values measured on point-contact test equipment MTM. The development of this program has provided the Machines Engineering Division of a tool that has allowed, and especially will allow to evaluate the importance of each of the rheological parameters on the various problems that will have to be addressed, evaluation performed hitherto described methods that phenomenology approximated with much less accuracy. When using our numerical procedure to simulate real situations we have encountered the obstacle that is very difficult to find, in the literature and database, parameters characterizing the rheological behaviour of the lubricant in the usual conditions of pressure, temperature and shear rate in which you work in this type of contact, and the few measures that exist for these operating conditions are unreliable. Thus in addition to the main objective of this thesis, we have developed a methodology to characterize the lubricants in these extreme conditions. This methodology is based on the good description, which makes our program, of the coefficient of friction, that allowed us to obtain the lubricant rheological parameters from experimental measurements of the friction coefficient generated on lubricated MTM equipment with the lubricant to be characterized.

CO2 soil flux baseline at the technological development plant for CO2 injection at Hontomin (Burgos, Spain)

From the end of 2013 and during the following two years, 20 kt of CO2sc are planned to be injected in a saline reservoir (1500 m depth) at the Hontomín site (NE Spain). The target aquifers are Lower Jurassic limestone formations which are sealed by Lower Cretaceous clay units at the Hontomín site (NE Spain). The injection of CO2 is part of the activities committed in the Technology Development phase of the EC-funded OXYCFB300 project (European Energy Program for Recovery – EEPR, http://www.compostillaproject.eu), which include CO2 injection strategies, risk assessment, and testing and validating monitoring methodologies and techniques. Among the monitoring works, the project is intended to prove that present-day technology is able to monitor the evolution of injected CO2 in the reservoir and to detect potential leakage. One of the techniques is the measurement of CO2 flux at the soil–atmosphere interface, which includes campaigns before, during and after the injection operations. In this work soil CO2 flux measurements in the vicinity of oil borehole, drilled in the eighties and named H-1 to H-4, and injection and monitoring wells were performed using an accumulation chamber equipped with an IR sensor. Seven surveys were carried out from November 2009 to summer 2011. More than 4000 measurements were used to determine the baseline flux of CO2 and its seasonal variations. The measured values were low (from 5 to 13 g m−2 day−1) and few outliers were identified, mainly located close to the H-2 oil well. Nevertheless, these values cannot be associated to a deep source of CO2, being more likely related to biological processes, i.e. soil respiration. No anomalies were recognized close to the deep fault system (Ubierna Fault) detected by geophysical investigations. There, the CO2 flux is indeed as low as other measurement stations. CO2 fluxes appear to be controlled by the biological activity since the lowest values were recorded during autumn-winter seasons and they tend to increase in warm periods. Two reference CO2 flux values (UCL50 of 5 g m−2 d−1 for non-ploughed areas in autumn–winter seasons and 3.5 and 12 g m−2 d−1 for in ploughed and non-ploughed areas, respectively, in spring–summer time, and UCL99 of 26 g m−2 d−1 for autumn–winter in not-ploughed areas and 34 and 42 g m−2 d−1 for spring–summer in ploughed and not-ploughed areas, respectively) were calculated. Fluxes higher than these reference values could be indicative of possible leakage during the operational and post-closure stages of the storage project.

Improvements for B.E.M. implementation in micros

This paper presents a computer program developed to run in a micro I.B.M.-P.C. wich incorporates some features in order to optimize the number of operations needed to compute the solution of plane potential problems governed by Laplace's equation by using the Boundary Integral Equation Method (B.I.E.M.). Also incorporated is a routine to plot isolines inside the domain under study.

FRe building technological products

Nowadays "Flood Resilient (FRe) Building Technological Products" is an undefined concept, and concerned FRe solutions cannot be even easily identified. There is an interest in offering an identification and classification of the referred products, since it will be useful for stakeholders and populations at flood risk for adopting the most adequate protections when facing floods. There are many barriers for the implementation of "FRe building technological products", and particularly their standardization is still a major challenge. To put into contact such solutions with final customers, it appears necessary to protocolize them all. The classification effort achieved in this document shall be considered as a necessary preliminary step in order to open the road to the market to FRe building technological solutions.

Arquitectura de Control para la Conducción Autónoma de Vehículos en Entornos Urbanos y Autovías

Hoy en día, el desarrollo tecnológico en el campo de los sistemas inteligentes de transporte (ITS por sus siglas en inglés) ha permitido dotar a los vehículos con diversos sistemas de ayuda a la conducción (ADAS, del inglés advanced driver assistance system), mejorando la experiencia y seguridad de los pasajeros, en especial del conductor. La mayor parte de estos sistemas están pensados para advertir al conductor sobre ciertas situaciones de riesgo, como la salida involuntaria del carril o la proximidad de obstáculos en el camino. No obstante, también podemos encontrar sistemas que van un paso más allá y son capaces de cooperar con el conductor en el control del vehículo o incluso relegarlos de algunas tareas tediosas. Es en este último grupo donde se encuentran los sistemas de control electrónico de estabilidad (ESP - Electronic Stability Program), el antibloqueo de frenos (ABS - Anti-lock Braking System), el control de crucero (CC - Cruise Control) y los más recientes sistemas de aparcamiento asistido. Continuando con esta línea de desarrollo, el paso siguiente consiste en la supresión del conductor humano, desarrollando sistemas que sean capaces de conducir un vehículo de forma autónoma y con un rendimiento superior al del conductor. En este trabajo se presenta, en primer lugar, una arquitectura de control para la automatización de vehículos. Esta se compone de distintos componentes de hardware y software, agrupados de acuerdo a su función principal. El diseño de la arquitectura parte del trabajo previo desarrollado por el Programa AUTOPIA, aunque introduce notables aportaciones en cuanto a la eficiencia, robustez y escalabilidad del sistema. Ahondando un poco más en detalle, debemos resaltar el desarrollo de un algoritmo de localización basado en enjambres de partículas. Este está planteado como un método de filtrado y fusión de la información obtenida a partir de los distintos sensores embarcados en el vehículo, entre los que encontramos un receptor GPS (Global Positioning System), unidades de medición inercial (IMU – Inertial Measurement Unit) e información tomada directamente de los sensores embarcados por el fabricante, como la velocidad de las ruedas y posición del volante. Gracias a este método se ha conseguido resolver el problema de la localización, indispensable para el desarrollo de sistemas de conducción autónoma. Continuando con el trabajo de investigación, se ha estudiado la viabilidad de la aplicación de técnicas de aprendizaje y adaptación al diseño de controladores para el vehículo. Como punto de partida se emplea el método de Q-learning para la generación de un controlador borroso lateral sin ningún tipo de conocimiento previo. Posteriormente se presenta un método de ajuste on-line para la adaptación del control longitudinal ante perturbaciones impredecibles del entorno, como lo son los cambios en la inclinación del camino, fricción de las ruedas o peso de los ocupantes. Para finalizar, se presentan los resultados obtenidos durante un experimento de conducción autónoma en carreteras reales, el cual se llevó a cabo en el mes de Junio de 2012 desde la población de San Lorenzo de El Escorial hasta las instalaciones del Centro de Automática y Robótica (CAR) en Arganda del Rey. El principal objetivo tras esta demostración fue validar el funcionamiento, robustez y capacidad de la arquitectura propuesta para afrontar el problema de la conducción autónoma, bajo condiciones mucho más reales a las que se pueden alcanzar en las instalaciones de prueba. ABSTRACT Nowadays, the technological advances in the Intelligent Transportation Systems (ITS) field have led the development of several driving assistance systems (ADAS). These solutions are designed to improve the experience and security of all the passengers, especially the driver. For most of these systems, the main goal is to warn drivers about unexpected circumstances leading to risk situations such as involuntary lane departure or proximity to other vehicles. However, other ADAS go a step further, being able to cooperate with the driver in the control of the vehicle, or even overriding it on some tasks. Examples of this kind of systems are the anti-lock braking system (ABS), cruise control (CC) and the recently commercialised assisted parking systems. Within this research line, the next step is the development of systems able to replace the human drivers, improving the control and therefore, the safety and reliability of the vehicles. First of all, this dissertation presents a control architecture design for autonomous driving. It is made up of several hardware and software components, grouped according to their main function. The design of this architecture is based on the previous works carried out by the AUTOPIA Program, although notable improvements have been made regarding the efficiency, robustness and scalability of the system. It is also remarkable the work made on the development of a location algorithm for vehicles. The proposal is based on the emulation of the behaviour of biological swarms and its performance is similar to the well-known particle filters. The developed method combines information obtained from different sensors, including GPS, inertial measurement unit (IMU), and data from the original vehicle’s sensors on-board. Through this filtering algorithm the localization problem is properly managed, which is critical for the development of autonomous driving systems. The work deals also with the fuzzy control tuning system, a very time consuming task when done manually. An analysis of learning and adaptation techniques for the development of different controllers has been made. First, the Q-learning –a reinforcement learning method– has been applied to the generation of a lateral fuzzy controller from scratch. Subsequently, the development of an adaptation method for longitudinal control is presented. With this proposal, a final cruise control controller is able to deal with unpredictable environment disturbances, such as road slope, wheel’s friction or even occupants’ weight. As a testbed for the system, an autonomous driving experiment on real roads is presented. This experiment was carried out on June 2012, driving from San Lorenzo de El Escorial up to the Center for Automation and Robotics (CAR) facilities in Arganda del Rey. The main goal of the demonstration was validating the performance, robustness and viability of the proposed architecture to deal with the problem of autonomous driving under more demanding conditions than those achieved on closed test tracks.

Caracterización de usuario y tráfico en la evolución de la banda ancha en España

El mundo de las telecomunicaciones evoluciona a gran velocidad, acorde con las necesidades de los usuarios. El crecimiento del número de servicios a través de las conexiones que actualmente utilizamos para conectarnos a Internet (Ej. IPTV) con elevados requerimientos de ancho de banda, que junto a los servicios de nuevo nacimiento (ej. OTT), contribuyen tanto al aumento de la necesidad de mayores velocidades de conexión de los usuarios como a la implantación de nuevos modelos de calidad de servicio. Las redes de datos de banda ancha (fija y móvil) actuales deben, por lo tanto, experimentar una profunda transformación para conseguir solventar de una forma eficiente los problemas y las necesidades de tráfico, pudiendo así absorber el progresivo incremento del ancho de banda, dejando las puertas abiertas a futuras mejoras. Y para ello las operadoras se nutrirán con la valiosa información de tráfico y usuario que les lleven a tomar las mejores decisiones de cara a que las transformaciones llevadas a cabo cubran exactamente lo que el usuario demanda de la forma más eficiente posible. Con estas premisas, surgieron las ideas que se plasmaron como objetivos del PFC : La idea de narrar el despliegue de la banda ancha en España desde sus orígenes hasta la actualidad, enfocando su crecimiento desde un punto de vista sociotecnológico. Dando continuidad al punto anterior, se persiguió la idea de conocer las herramientas sociales y tecnológicas a raíz de las cuales se pueda realizar una previsión del tráfico en las redes de las operadoras en un futuro cercano. La pretensión de mostrar las características de los usuarios de banda ancha y del tráfico de datos que generan, que son de carácter crítico para las operadoras en la elaboración de forma adecuada de la planificación de sus redes. La intención de revelar los procedimientos de las operadoras para que, una vez conocidas las características de sus usuarios, se puedan cumplir los requisitos demandados por los mismos: QoS y los indicadores clave de rendimiento (KPIs) Por otro lado, el nivel de detalle dado pretende adecuarse a un público que no tenga profundos conocimientos sobre la materia, y salvo partes bastante concretas, se puede catalogar este trabajo como de abierto al público en general. ABSTRACT. The world of telecommunications is evolving at high speed, according to the needs of users. The growing of services number through the connections that currently have been used to connect to the Internet (eg IPTV ) with high bandwidth requirements, which together with the new birth services (eg OTT ) contribute both to increased the need for higher connection speeds users and the implementation of new models of service quality. Data networks broadband (fixed and mobile ) today must , therefore, undergo a deep transformation to achieve an efficient solving problems and traffic needs, thus being able to absorb the gradual increase of bandwidth, leaving the door open to future improvements. And for that the operators will be nurtured with valuable information and user traffic that lead them to make better decisions in the face of the transformations carried out exactly meet the user demand for the most efficient possible way. With these assumptions, the ideas that emerged were expressed as PFC objectives : The idea of narrating the broadband deployment in Spain from its origins to the present, focusing its growth from a socio-technological approach. Continuing the previous point, it pursued the idea of knowing the social tools and technology as a result of which it can perform a traffic forecast operators networks in the near future. The attempt to show the characteristics of broadband users and data traffic they generate, which are mission critical for operators in developing adequately planning their networks. The intention to disclose procedures for operators, once known the characteristics of their users, it can meet the requirements demanded by them: QoS and key performance indicators (KPI). On the other hand, the level of detail given suit seeks an audience that does not have deep knowledge on the subject, unless quite specific parts, this work can be classified as open to the general public.

A cybernetic theory about computer interfaces and human factors within a framework of technological innovation

This paper is based on the following postulates taken from a book recently published by this author (Sáez-Vacas, 1990(1)): a) technological innovation in a company is understood to be the process and set of changes that the company undergoes as a result of a specific type of technology; b) the incorporation of technology in the company does not necessarily result in innovation, modernization and progress; c) the very words "modernization" and "progress" are completely bereft of any meaning if isolated from the concept of complexity in its broadest sense, including the human factor. Turning to office technology in specific, the problem of managing office technology for business innovation purposes can be likened to the problem of managing third level complexity, following the guidelines of a three-level complexity model proposed by the author some years ago

Can the exercise mode determine lipid profile improvements in obese patients?

Influencia del modo de ejercicio sobre el perfil lipídico