Controller design for variable-speed permanent magnet wind turbine generators interfaced with Z-source inverter

Increased awareness of environmental concerns has caused greater interest in developing power sources based on renewable technologies, such as wind. Due to the intermittent nature of the wind speed, output voltage and frequency of the direct driven permanent magnet synchronous generators (PMSG) are normally unsteady. Recently proposed Z-source inverter has been considered as a potential solution for grid interfacing wind power generators, thanks to buck-boost function that the single stage Z-source inverter can offer. Two control methodologies, namely unified controller for isolated operation and a multi-loop controller for grid interfaced operation are investigated in this paper. Theoretical analysis of these two control schemes is presented and experimental results to verify the effectiveness of the control method are also included.

On the design of power buffer and its applications

A power electronics-based buffer is examined in which through control of its PWM converters, the buffer-load combination is driven to operate under either constant power or constant impedance modes. A battery, incorporated within the buffer, provides the energy storage facility to facilitate the necessary power flow control. Real power demand from upstream supply is regulated under fault condition, and the possibility of voltage or network instability is reduced. The proposed buffer is also applied to a wind farm. It is shown that the buffer stabilizes the power contribution from the farm. Based on a battery cost-benefit analysis, a method is developed to determine the optimal level of the power supplied from the wind farm and the corresponding capacity of the battery storage system.

Real or imagined? A study exploring the existence of common method variance effects in road safety research

Common method variance (CMV) has received little attention within the field of road safety research despite a heavy reliance on self-report data. Two surveys were completed by 214 motorists over a two-month period, allowing associations between social desirability and key road safety variables and relationships between scales across the two survey waves to be examined. Social desirability was found to have a strong negative correlation with the Driver Behaviour Questionnaire (DBQ) sub-scales as well as age, but not with crashes and offences. Drivers who scored higher on the social desirability scale were also less likely to report aberrant driving behaviours as measured by the DBQ. Controlling for social desirability did not substantially alter the predictive relationship between the DBQ and the crash and offences variables. The strength of the correlations within and between the two waves were also compared with the results strongly suggesting that effects associated with CMV were present. Identification of CMV would be enhanced by the replication of this study with a larger sample size and comparing self-report data with official sources.

An urban design perspective to classify knowledge precincts : a typological analysis of global best practices

Purpose: The paper seeks to investigate emerging knowledge precincts under the urban design lens in order to identify recurrent spatial patterns of urban forms and functions to gather an understanding of physical aspects that contribute to the creation of place quality. Scope: This paper focuses on the physical design and layout of specific precincts. Although socio-economic and other factors come into play imparting the distinctiveness; this paper only focuses on the spatial dimensions. Method: The research first develops a design typology framework through the lead of literature, and then utilizes it to identify recurrent elements in knowledge precinct design in order to develop taxonomy of patterns and layouts. Results: The research reported in this paper provides preliminary insights into the various form and functional factors playing role in the design of knowledge precincts and evaluates the elements that contribute to the success of these urban interventions. Recommendations: The paper recommends the use of particular design-based solutions in order to enhance the place making in knowledge precincts. Conclusions: The study concludes that despite the locational, regulatory and other contextual differences, the underlying driving principle of providing place quality to people leads to the emergence of identifiable spatial patterns across the knowledge precincts.

Experimental investigation and design of lipped channel beams in shear

Cold-formed high strength steel members are increasingly used as primary load bearing components in low rise buildings. Lipped channel beam (LCB) is one of the most commonly used flexural members in these applications. In this research an experimental study was undertaken to investigate the shear behaviour and strengths of LCB sections. Simply supported test specimens of back to back LCBs with aspect ratios of 1.0 and 1.5 were loaded at mid-span until failure. Test specimens were chosen such that all three types of shear failure (shear yielding, inelastic and elastic shear buckling) occurred in the tests. The ultimate shear capacity results obtained from the tests were compared with the predictions from the current design rules in Australian/NewZealand and American cold-formed steel design standards. This comparison showed that these shear design rules are very conservative as they did not include the post-buckling strength observed in the shear tests and the higher shear buckling coefficient due to the additional fixity along the web-flange juncture. Improved shear design equations are proposed in this paper by including the above beneficial effects. Suitable lower bound design rules were also developed under the direct strength method format. This paper presents the details of this experimental study and the results including the improved design rules for the shear capacity of LCBs. It also includes the details of tests of LCBs subject to combined shear and flange distortion, and combined bending and shear actions, and proposes suitable design rules to predict the capacities in these cases.

Design of a nonlinear excitation controller using inverse filtering for transient stability enhancement

This paper proposes a nonlinear excitation controller to improve transient stability, oscillation damping and voltage regulation of the power system. The energy function of the predicted system states is used to obtain the desired flux for the next time step, which in turn is used to obtain a supplementary control input using an inverse filtering method. The inverse filtering technique enables the system to provide an additional input for the excitation system, which forces the system to track the desired flux. Synchronous generator flux saturation model is used in this paper. A single machine infinite bus (SMIB) test system is used to demonstrate the efficacy of the proposed control method using time-domain simulations. The robustness of the controller is assessed under different operating conditions.

A collaborative rapid persona-building workshop : creating design personas with health researchers

In the HealthMap project for People With HIV, (PWHIV) designers employed a collaborative rapid ‘persona-building' workshop with health researchers to develop patient personas that embodied patient-centred design goals and contextual awareness from a variety of qualitative and quantitative data. On reflection, this collaborative rapid workshop was a process for drawing together the divergent user research insights and expertise of stakeholders into focus for a chronic disease self-management design. This paper discusses, (i) an analysis of the transcript of the workshop and, (ii) interviews with five practising senior designers, in order to reflect on how the persona-building process was enacted and its role in the HealthMap design evolution. The collaborative rapid persona-building methodology supported: embedding user research insights, eliciting domain expertise, introducing design thinking, facilitating stakeholder collaboration and defining early design requirements. The contribution of this paper is to model the process of collaborative rapid persona-building and to introduce the collaborative rapid persona-building framework as a method to generate design priorities from domain expertise and user research data.

A novel tuning method for advanced line drop compensator and its application to response coordination of distributed generation with voltage regulating devices

Nowadays, integration of small-scale electricity generators, known as Distributed Generation (DG), into distribution networks has become increasingly popular. This tendency together with the falling price of DG units has a great potential in giving the DG a better chance to participate in voltage regulation process, in parallel with other regulating devices already available in the distribution systems. The voltage control issue turns out to be a very challenging problem for distribution engineers, since existing control coordination schemes need to be reconsidered to take into account the DG operation. In this paper, a control coordination approach is proposed, which is able to utilize the ability of the DG as a voltage regulator, and at the same time minimize the interaction of DG with another DG or other active devices, such as On-load Tap Changing Transformer (OLTC). The proposed technique has been developed based on the concepts of protection principles (magnitude grading and time grading) for response coordination of DG and other regulating devices and uses Advanced Line Drop Compensators (ALDCs) for implementation. A distribution feeder with tap changing transformer and DG units has been extracted from a practical system to test the proposed control technique. The results show that the proposed method provides an effective solution for coordination of DG with another DG or voltage regulating devices and the integration of protection principles has considerably reduced the control interaction to achieve the desired voltage correction.

From ideation to sculpture : digital sculpting as the primary 'ideation' tool for creature design

This research project examined the potential for circumventing drawing in the ideation process by adopting digital sculpture as the primary conceptual development and design tool for the digital sculpting of creature designs. Through a series of experimental research cycles, multiple frameworks were explored with the aim of identifying a methodology for creating '3D sculpted sketches' for the initial phases of the ideation process. This research project acknowledges that drawing still remains the predominant method of visualising design ideas for characters and creatures for many artists. However, alongside other ideation techniques digital sculpting can function as a rapid and responsive tool to visualize and explore forms in a digital sculpting environment for the conceptualisation of multiple creature design variations. The results of this study are significant for emerging digital sculptors who may not necessarily have a well-defined creative brief or initial concept.

Improving the teaching and learning of steel structural design

Engineering students are best able to understand theory when one explains it in relation to realistic problems and its practical applications. Teaching theory in isolation has led to lower levels of comprehension and motivation and a correspondingly higher rate of failure. At Queensland University of Technology, a number of new methods have been introduced recently to improve the teaching and learning of steel structural design at undergradt1ate level. In the basic steel structures subject a project-based teaching method was introduced in which the students were required to analyse, design and build the lightest I most efficient steel columns for a given target capacity. A design assignment involving simple, but real structures was also introduced in the basic steel structures subject. Both these exercises simulated realistic engineering problems from the early years of the course and produced a range of benefits. Improvements to the teaching and learning was also made through integration of a number of related structural engineering subjects and by the introduction of animated computer models and laboratory models. This paper presents the details of all these innovative methods which improved greatly the students' understanding of the steel structures design process.

Design of stiffened plates with openings

The load-deflection and ultimate strength behaviour of longitudinally stiffened plates with openings was studied using a second-order elastic post-buckling analysis and a rigid-plastic analysis. The ultimate strength was predicted from the intersection point of elastic and rigid-plastic curves and the Perry strut formula. Comparison with experimental results shows that satisfactory prediction of ultimate strength can be obtained by this simple method. Effects of the size of opening, the initial geometrical imperfections and the plate slenderness ratio on the strength of perforated stiffened plates were also studied.

The impact of socialisation on graduates’ public service motivation : a mixed method study

The need to attract and retain a high calibre cadre of public servants today has resulted in a renaissance of interest in public service motivation (PSM) within public management literature. This article outlines a study of PSM with graduate employees within an Australian public sector. The study extends our understanding of PSM by adopting a longitudinal, mixed method design, including surveys and individual interviews, to consider the effects of socialisation on levels of PSM. Results show an organisation's mission and values do not affect individual PSM while work type and communication style is vital and organisational socialisation can provide a negative influence.

Are you on board? The role of design-led innovation in strengthening key partnerships within an Australian airport

A popular lexicon for announcing partnerships within aviation is being ‘on-board’. Like boarding a plane, business partnerships requires trust in the expertise and the philosophy of another organisation. This paper reports upon the process and findings from the completion of a customer engagement project within a leading Australian Airport, as part of the wider uptake of design-led innovation. The project was completed bilaterally with Airport Corporation and prominent retail business partner undertaking a design-led approach to collaboratively explore an observed market trend affecting the performance of both businesses. A design-led catalyst facilitated the completion of this project, working within the Airport Corporation to disseminate the skills and philosophy of design over an 18 month period using an action research method. Findings reveal that the working environment necessary for design to be utilised requires; trust in the design-led approach as a new and exploratory way of completing work; leadership within the execution and delivery of project deliverables, and; a shared intrinsic motivation to develop new skills through a design-led approach which challenges a business-as-usual mentality (BAU). Design-led innovation can be deployed specifically to strengthen business partnerships through collaborative and explorative customer engagement.

Illuminative evaluation as a method applied to Australian Government policy borrowing and implementation in higher education

Any government deciding to invoke widespread change in its higher education sector through implementation of new policies impacts on every institution and all staff and students, often in both the time taken up and the heightened emotions caused. The central phenomenon that this study addresses is the process and consequences of policy changes in higher education in Australia. The aim of this article is to record the research design through the perspective (evaluation research), theoretical framework (program evaluation) and methods (content analysis, descriptive statistical analysis and bibliometric analysis) applied to the investigation of the 2003 federal government higher education reform package. This approach allows both the intended and unintended consequences arising from the policy implementation of three national initiatives focused on learning and teaching in higher education in Australia to surface. As a result, this program evaluation, also known in some disciplines as policy implementation analysis, will demonstrate the applicability of illuminative evaluation as a methodology and reinforce how program evaluation will assist and advise future government reform and policy implementation, and will serve as a legacy for future evaluative research.Any government deciding to invoke widespread change in its higher education sector through implementation of new policies impacts on every institution and all staff and students, often in both the time taken up and the heightened emotions caused. The central phenomenon that this study addresses is the process and consequences of policy changes in higher education in Australia. The aim of this article is to record the research design through the perspective (evaluation research), theoretical framework (program evaluation) and methods (content analysis, descriptive statistical analysis and bibliometric analysis) applied to the investigation of the 2003 federal government higher education reform package. This approach allows both the intended and unintended consequences arising from the policy implementation of three national initiatives focused on learning and teaching in higher education in Australia to surface. As a result, this program evaluation, also known in some disciplines as policy implementation analysis, will demonstrate the applicability of illuminative evaluation as a methodology and reinforce how program evaluation will assist and advise future government reform and policy implementation, and will serve as a legacy for future evaluative research.

A method for optimal fit of patient-specific fracture fixation plates

Anatomically pre-contoured fracture fixation plates are a treatment option for bone fractures. A well-fitting plate can be used as a tool for anatomical reduction of the fractured bone. However, recent studies showed that some plates fit poorly for many patients due to considerable shape variations between bones of the same anatomical site. Therefore, the plates have to be manually fitted and deformed by surgeons to fit each patient optimally. The process is time-intensive and labor-intensive, and could lead to adverse clinical implications such as wound infection or plate failure. This paper proposes a new iterative method to simulate the patient-specific deformation of an optimally fitting plate for pre-operative planning purposes. We further demonstrate the validation of the method through a case study. The proposed method involves the integration of four commercially available software tools, Matlab, Rapidform2006, SolidWorks, and ANSYS, each performing specific tasks to obtain a plate shape that fits optimally for an individual tibia and is mechanically safe. A typical challenge when crossing multiple platforms is to ensure correct data transfer. We present an example of the implementation of the proposed method to demonstrate successful data transfer between the four platforms and the feasibility of the method.