Analysis of phasor measurement method in tracking the power frequency of distorted signals

This paper presents an analysis of phasor measurement method for tracking the fundamental power frequency to show if it has the performance necessary to cope with the requirements of power system protection and control. In this regard, several computer simulations presenting the conditions of a typical power system signal especially those highly distorted by harmonics, noise and offset, are provided to evaluate the response of the Phasor Measurement (PM) technique. A new method, which can shorten the delay of estimation, has also been proposed for the PM method to work for signals free of even-order harmonics.

Power management and power flow control with back-to-back converters in a utility connected microgrid

This paper proposes a method for power flow control between utility and microgrid through back-to-back converters, which facilitates desired real and reactive power flow between utility and microgrid. In the proposed control strategy, the system can run in two different modes depending on the power requirement in the microgrid. In mode-1, specified amount of real and reactive power are shared between the utility and the microgrid through the back-to-back converters. Mode-2 is invoked when the power that can be supplied by the DGs in the microgrid reaches its maximum limit. In such a case, the rest of the power demand of the microgrid has to be supplied by the utility. An arrangement between DGs in the microgrid is proposed to achieve load sharing in both grid connected and islanded modes. The back-to-back converters also provide total frequency isolation between the utility and the microgrid. It is shown that the voltage or frequency fluctuation in the utility side has no impact on voltage or power in microgrid side. Proper relay-breaker operation coordination is proposed during fault along with the blocking of the back-to-back converters for seamless resynchronization. Both impedance and motor type loads are considered to verify the system stability. The impact of dc side voltage fluctuation of the DGs and DG tripping on power sharing is also investigated. The efficacy of the proposed control ar-rangement has been validated through simulation for various operating conditions. The model of the microgrid power system is simulated in PSCAD.

Load sharing and power quality enhanced operation of a distributed microgrid

This paper describes control methods for proper load sharing between parallel converters connected in a microgrid and supplied by distributed generators (DGs). It is assumed that the microgrid spans a large area and it supplies loads in both in grid connected and islanded modes. A control strategy is proposed to improve power quality and proper load sharing in both islanded and grid connected modes. It is assumed that each of the DGs has a local load connected to it which can be unbalanced and/or nonlinear. The DGs compensate the effects of unbalance and nonlinearity of the local loads. Common loads are also connected to the microgrid, which are supplied by the utility grid under normal conditions. However during islanding, each of the DGs supplies its local load and shares the common load through droop characteristics. Both impedance and motor loads are considered to verify the system response. The efficacy of the controller has been validated through simulation for various operating conditions using PSCAD. It has been found through simulation that the total Harmonic Distortion (THD) of the of the microgrid voltage is about 10% and the negative and zero sequence component are around 20% of the positive sequence component before compensation. After compensation, the THD remain below 0.5%, whereas, negative and zero sequence components of the voltages remain below 0.02% of the positive sequence component.

Evaluation of aerial remote sensing techniques for vegetation management in power line corridors

The following paper presents an evaluation of airborne sensors for use in vegetation management in powerline corridors. Three integral stages in the management process are addressed including, the detection of trees, relative positioning with respect to the nearest powerline and vegetation height estimation. Image data, including multi-spectral and high resolution, are analyzed along with LiDAR data captured from fixed wing aircraft. Ground truth data is then used to establish the accuracy and reliability of each sensor thus providing a quantitative comparison of sensor options. Tree detection was achieved through crown delineation using a Pulse-Coupled Neural Network (PCNN) and morphologic reconstruction applied to multi-spectral imagery. Through testing it was shown to achieve a detection rate of 96%, while the accuracy in segmenting groups of trees and single trees correctly was shown to be 75%. Relative positioning using LiDAR achieved a RMSE of 1.4m and 2.1m for cross track distance and along track position respectively, while Direct Georeferencing achieved RMSE of 3.1m in both instances. The estimation of pole and tree heights measured with LiDAR had a RMSE of 0.4m and 0.9m respectively, while Stereo Matching achieved 1.5m and 2.9m. Overall a small number of poles were missed with detection rates of 98% and 95% for LiDAR and Stereo Matching.

Cyber bullying in schools and the law : is there an effective means of addressing the power imbalance?

Cyber bullying – or bullying through the use of technology – is a growing phenomenon which is currently most commonly experienced by young people and the consequences manifested in schools. Cyber bullying shares many of the same attributes as face-to-face bullying such as a power imbalance and a sense of helplessness on the part of the target. Not surprisingly, targets of face-to-face bullying are increasingly turning to the law, and it is likely that targets of cyber bullying may also do so in an appropriate case. This article examines the various criminal, civil and vilification laws that may apply to cases of cyber bullying and assesses the likely effectiveness of these laws as a means of redressing that power imbalance between perpetrator and target.

Psychometric evaluation of the Chinese version of the diabetes coping measure scale

Purpose: To evaluate the psychometric properties of a Chinese version of the Diabetes Coping Measure (DCM-C) scale.----- Methods: A self-administered questionnaire was completed by 205 people with type 2 diabetes from the endocrine outpatient departments of three hospitals in Taiwan. Confirmatory factor analysis, criterion validity, and internal consistency reliability were conducted to evaluate the psychometric properties of the DCM-C.----- Findings: Confirmatory factor analysis confirmed a four-factor structure (χ2 /df ratio=1.351, GFI=.904, CFI=.902, RMSEA=.041). The DCM-C was significantly associated with HbA1c and diabetes self-care behaviors. Internal consistency reliability of the total DCM-C scale was .74. Cronbach’s alpha coefficients for each subscale of the DCM-C ranged from .37 (tackling spirit) to .66 (diabetes integration).----- Conclusions: The DCM-C demonstrated satisfactory reliability and validity to determine the use of diabetes coping strategies. The tackling spirit dimension needs further refinement when applies this scale to Chinese populations with diabetes.----- Clinical Relevance: Healthcare providers who deal with Chinese people with diabetes can use the DCM-C to implement an early determination of diabetes coping strategies.

Detection and Estimation of Nonstationary Power Transients

This chapter looks at issues of non-stationarity in determining when a transient has occurred and when it is possible to fit a linear model to a non-linear response. The first issue is associated with the detection of loss of damping of power system modes. When some control device such as an SVC fails, the operator needs to know whether the damping of key power system oscillation modes has deteriorated significantly. This question is posed here as an alarm detection problem rather than an identification problem to get a fast detection of a change. The second issue concerns when a significant disturbance has occurred and the operator is seeking to characterize the system oscillation. The disturbance initially is large giving a nonlinear response; this then decays and can then be smaller than the noise level ofnormal customer load changes. The difficulty is one of determining when a linear response can be reliably identified between the non-linear phase and the large noise phase of thesignal. The solution proposed in this chapter uses “Time-Frequency” analysis tools to assistthe extraction of the linear model.

Knowledge is not power, but it’s a start : young people and employment entitlements

This paper employs empirical evidence from a survey of Queensland secondary school students to examine their knowledge about their wages and working conditions. It does so within the theoretical lens of the Gagne (or Gagne-Briggs) theory of instruction, which centres on the content of learning and how learning is acquired (Gagne, Briggs & Wager, 1988). While Gagne articulates five categories of learning, our focus here is on two; verbal information or declarative knowledge (facts that people can declare), and procedural knowledge (the rules and procedures for achieving outcomes). We show that student workers know little about the instruments governing their employment, or their workplace entitlements. Of the total sample of year 9 and year 11 students surveyed (n=892), those students who worked, or who had worked in the past year (n=438), were asked to identify whether they were employed under an award, collective agreement or AWA. Eighty three per cent of students did not know which industrial instrument set their wages. We argue that if young workers do not have declarative knowledge of their entitlements, nor basic procedural knowledge about redress, then they are not in a position to deploy Gagne’s ‘cognitive strategies’ that would enable them to take action to ensure their working conditions meet legal minima. We advocate that young workers should be given summary information on their wages and other entitlements on appointment and that such summary information should be readily available on employers’ noticeboards and electronically on company websites, and that the information should include a brief summary of avenues for redressing issues of underpayment or sub-standard conditions.

The impact of Health Information Technology (I-HIT) scale : the Australian results

One of role of the nurse in the clinical setting is that of coordinating communication across the healthcare team. On a daily basis nurses interact with the person receiving care, their family members, and multiple care providers thus placing the nurse in the central position with access to a vast array of information on the person. Through this nurses have historically functioned as “information repositories”. With the advent of Health Information Technology (HIT) tools there is a potential that HIT could impact interdisciplinary communication, practice efficiency and effectiveness, relationships and workflow in acute care settings \[1]\[3]. In 2005, the HIMSS Nursing Informatics Community developed the IHITScale to measure the impact of HIT on the nursing role and interdisciplinary communication in USA hospitals. In 2007, nursing informatics colleagues from Australia, Finland, Ireland, New Zealand, Scotland and the USA formed a research collaborative to validate the IHIT in six additional countries. This paper will discuss the background, methodology, results and implications from the Australian IHIT survey of over 1100 nurses. The results are currently being analyzed and will be presented at the conference.

Validation of the impact of Health Information Technology (I-HIT) scale : an international collaborative

In 2005, the Healthcare Information Management Systems Society (HIMSS) Nursing Informatics Community developed a survey to measure the impact of health information technology (HIT), the IHIT Scale, on the role of nurses and interdisciplinary communication in hospital settings. In 2007, nursing informatics colleagues from Australia, England, Finland, Ireland, New Zealand, Scotland and the United States formed a research collaborative to validate the IHIT across countries. All teams have completed construct and face validation in their countries. Five out of six teams have initiated reliability testing by practicing nurses. This paper reports the international collaborative’s validation of the IHIT Scale completed to date.

Infrastructure sustainability : differential axial shortening of concrete structures

High density development has been seen as a contribution to sustainable development. However, a number of engineering issues play a crucial role in the sustainable construction of high rise buildings. Non linear deformation of concrete has an adverse impact on high-rise buildings with complex geometries, due to differential axial shortening. These adverse effects are caused by time dependent behaviour resulting in volume change known as ‘shrinkage’, ‘creep’ and ‘elastic’ deformation. These three phenomena govern the behaviour and performance of all concrete elements, during and after construction. Reinforcement content, variable concrete modulus, volume to surface area ratio of the elements, environmental conditions, and construction quality and sequence influence on the performance of concrete elements and differential axial shortening will occur in all structural systems. Its detrimental effects escalate with increasing height and non vertical load paths resulting from geometric complexity. The magnitude of these effects has a significant impact on building envelopes, building services, secondary systems, and lifetime serviceability and performance. Analytical and test procedures available to quantify the magnitude of these effects are limited to a very few parameters and are not adequately rigorous to capture the complexity of true time dependent material response. With this in mind, a research project has been undertaken to develop an accurate numerical procedure to quantify the differential axial shortening of structural elements. The procedure has been successfully applied to quantify the differential axial shortening of a high rise building, and the important capabilities available in the procedure have been discussed. A new practical concept, based on the variation of vibration characteristic of structure during and after construction and used to quantify the axial shortening and assess the performance of structure, is presented.

Customer-oriented deviance (COD) : a conceptualisation, development and validation of a behavioural measure

Frontline employee behaviours are recognised as vital for achieving a competitive advantage for service organisations. The services marketing literature has comprehensively examined ways to improve frontline employee behaviours in service delivery and recovery. However, limited attention has been paid to frontline employee behaviours that favour customers in ways that go against organisational norms or rules. This study examines these behaviours by introducing a behavioural concept of Customer-Oriented Deviance (COD). COD is defined as, “frontline employees exhibiting extra-role behaviours that they perceive to defy existing expectations or prescribed rules of higher authority through service adaptation, communication and use of resources to benefit customers during interpersonal service encounters.” This thesis develops a COD measure and examines the key determinants of these behaviours from a frontline employee perspective. Existing research on similar behaviours that has originated in the positive deviance and pro-social behaviour domains has limitations and is considered inadequate to examine COD in the services context. The absence of a well-developed body of knowledge on non-conforming service behaviours has implications for both theory and practice. The provision of ‘special favours’ increases customer satisfaction but the over-servicing of customers is also counterproductive for the service delivery and costly for the organisation. Despite these implications of non-conforming service behaviours, there is little understanding about the nature of these behaviours and its key drivers. This research builds on inadequacies in prior research on positive deviance, pro-social and pro-customer literature to develop the theoretical foundation of COD. The concept of positive deviance which has predominantly been used to study organisational behaviours is applied within a services marketing setting. Further, it addresses previous limitations in pro-social and pro-customer behavioural literature that has examined limited forms of behaviours with no clear understanding on the nature of these behaviours. Building upon these literature streams, this research adopts a holistic approach towards the conceptualisation of COD. It addresses previous shortcomings in the literature by providing a well bounded definition, developing a psychometrically sound measure of COD and a conceptually well-founded model of COD. The concept of COD was examined across three separate studies and based on the theoretical foundations of role theory and social identity theory. Study 1 was exploratory and based on in-depth interviews using the Critical Incident Technique (CIT). The aim of Study 1 was to understand the nature of COD and qualitatively identify its key drivers. Thematic analysis was conducted to analyse the data and the two potential dimensions of COD behaviours of Deviant Service Adaptation (DSA) and Deviant Service Communication (DSC) were revealed in the analysis. In addition, themes representing the potential influences of COD were broadly classified as individual factors, situational factors, and organisational factors. Study 2 was a scale development procedure that involved the generation and purification of items for the measure based on two student samples working in customer service roles (Pilot sample, N=278; Initial validation sample, N=231). The results for the reliability and Exploratory Factor Analyses (EFA) on the pilot sample suggested the scale had poor psychometric properties. As a result, major revisions were made in terms of item wordings and new items were developed based on the literature to reflect a new dimension, Deviant Use of Resources (DUR). The revised items were tested on the initial validation sample with the EFA analysis suggesting a four-factor structure of COD. The aim of Study 3 was to further purify the COD measure and test for nomological validity based on its theoretical relationships with key antecedents and similar constructs (key correlates). The theoretical model of COD consisting of nine hypotheses was tested on a retail and hospitality sample of frontline employees (Retail N=311; Hospitality N=305) of a market research panel using an online survey. The data was analysed using Structural Equation Modelling (SEM). The results provided support for a re-specified second-order three-factor model of COD which consists of 11 items. Overall, the COD measure was found to be reliable and valid, demonstrating convergent validity, discriminant validity and marginal partial invariance for the factor loadings. The results showed support for nomological validity, although the antecedents had differing impact on COD across samples. Specifically, empathy and perspective-taking, role conflict, and job autonomy significantly influenced COD in the retail sample, whereas empathy and perspective-taking, risk-taking propensity and role conflict were significant predictors in the hospitality sample. In addition, customer orientation-selling orientation, the altruistic dimension of organisational citizenship behaviours, workplace deviance, and social desirability responding were found to correlate with COD. This research makes several contributions to theory. First, the findings of this thesis extend the literature on positive deviance, pro-social and pro-customer behaviours. Second, the research provides an empirically tested model which describes the antecedents of COD. Third, this research contributes by providing a reliable and valid measure of COD. Finally, the research investigates the differential effects of the key antecedents in different service sectors on COD. The research findings also contribute to services marketing practice. Based on the research findings, service practitioners can better understand the phenomenon of COD and utilise the measurement tool to calibrate COD levels within their organisations. Knowledge on the key determinants of COD will help improve recruitment and training programs and drive internal initiatives within the firm.

A psychometric comparison of the Toronto Alexithymia Scale (TAS-20) and the Observer Alexithymia Scale (OAS) in an alcohol-dependent sample

Alexithymia is characterised by deficits in emotional insight and self reflection, that impact on the efficacy of psychological treatments. Given the high prevalence of alexithymia in Alcohol Use Disorders, valid assessment tools are critical. The majority of research on the relationship between alexithymia and alcohol-dependence has employed the self-administered Toronto Alexithymia Scale (TAS-20). The Observer Alexithymia Scale (OAS) has also been recommended. The aim of the present study was to assess the validity and reliability of the OAS and the TAS-20 in an alcohol-dependent sample. Two hundred and ten alcohol-dependent participants in an outpatient Cognitive Behavioral Treatment program were administered the TAS-20 at assessment and upon treatment completion at 12 weeks. Clinical psychologists provided observer assessment data for a subsample of 159 patients. The findings confirmed acceptable internal consistency, test-retest reliability and scale homogeneity for both the OAS and TAS-20, except for the low internal consistency of the TAS-20 EOT scale. The TAS-20 was more strongly associated with alcohol problems than the OAS.