Production of an axial piston: Impacts resulting from the substitution of steel by a polymer-based material

The substitution of steel as a raw material in the production of axial pistons for pressure washers by polyphthalamide, polytetrafluoroethylene and glass fiber-based composite was studied. The new production process with composite consists of only two steps, while the production of the steel piston is to comprise of thirteen steps. This replacement would result in an estimated reduction of 80% of water consumption, 83% of electricity consumption, 73% of the total cost and 88% of the final mass. With regard to the main mechanical properties required for the end product, the composite was found to withstand the critical axial loads and it shows acceptable wear resistance in an environment without lubrication, an additional advantage of this replacement. © 2012 Elsevier Ltd. All rights reserved.

Evaluation of the chemical interaction between carbon nanotubes functionalized with TGDDM tetrafunctional resin and hardener DDS

In this work, the chemical interaction between carbon nanotubes (MWCNT) functionalized with acyl chloride (SOCl2) and polymer chain tetrafuncional N,N,N′,N′-tetraglycidyl-4,4′- diaminodiphenylmethane (TGDDM) and hardener 4,4′diaminodiphenyl sulfone (DDS) has been monitored by Fourier transform infrared spectroscopy (FTIR) with a attenuated total reflectance (ATR) coupled. MWCNT were obtained from the pyrolysis of a mixture of camphor and ferrocene into a oven. The functionalization process was done by oxidative treatment in order to incorporate carboxylic group over the walls of MWCNT, before to be used SOCl2. The functionalized carbon nanotubes were evaluated by X-ray photoelectron spectroscopy (XPS), Raman and transmission electron microscopy (TEM). Nanostructured composites were processed by using epoxy resin with MWCNT in varying percentages. In this work it was observed that different percentages of functionalized nanotubes modify the interaction between the composite matrix and curing agent, where can be observed that in specimens with content less than 1 wt% MWCNT the chemical bond occurs preferentially from the opening of the SO double bond of the hardener and when is used MWCNT content higher than 1 wt% there is little chemical interaction with the SO bond of the hardener and most MWCNT binds to amine. © 2013 Elsevier Ltd.

Hybridization effect on the mechanical properties of curaua/glass fiber composites

The aim of this paper was to evaluate the effect of hybridizing glass and curaua fibers on the mechanical properties of their composites. These composites were produced by hot compression molding, with distinct overall fiber volume fraction, being either pure curaua fiber, pure glass fiber or hybrid. The mechanical characterization was performed by tensile, flexural, short beam, Iosipescu and also nondestructive testing. From the obtained results, it was observed that the tensile strength and modulus increased with glass fiber incorporation and for higher overall fiber volume fraction (%Vf). The short beam strength increased up to %Vf of 30 vol.%, evidencing a maximum in terms of overall fiber/matrix interface and composite quality. Hybridization has been successfully applied to vegetable/synthetic fiber reinforced polyester composites in a way that the various properties responded satisfactorily to the incorporation of a third component. © 2013 Published by Elsevier Ltd. All rights reserved.

Desenvolvimento e caracterização de dispositivos luminescentes híbridos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento e caracterização de compósitos poliméricos reforçados com fibras lignocelulósicas: HIPS / fibra de casca do coco verde e bagaço de cana de açucar

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Preparação e caracterização elétrica do compósito de poliuretano/negro de fumo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Fabricação, caracterização e aplicações do compósito PZT/PVDF

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Propriedades físicas do Poliestireno e do Poli (metacrilato de metila) modificados com Óleo de Buriti (mauritia flexuosa)

Nos dias atuais, cresce cada vez mais o uso de polímeros no nosso cotidiano. Esse crescimento deve-se essencialmente à sua aplicabilidade com grande eficácia na substituição de materiais clássicos como madeira, metais, vidros e até mesmo papel. Além disso, propriedades especiais de polímeros, como condutividade elétrica, fotoluminescência e difusividade térmica, tem sido objeto de interesse da comunidade cientifica básica e aplicada. Algumas dessas propriedades podem, dependendo da necessidade a qual se destina ser modificadas a partir da inserção de outras substancias em suas matrizes. O interesse cientifico por óleos vegetais vem se tornando cada vez mais frequente, um desses óleos conhecido como Óleo de Buriti (mauritia flexuosa), tem em sua composição um alto teor de acido oleico e pró-vitamina A (conhecida como β-caroteno), tais substancias apresentam propriedades interessantes que já foram reportadas por vários pesquisadores em periódicos científicos. Apresentamos nessa dissertação o estudo de algumas propriedades físicas de amostras de dois polímeros comerciais de uso rotineiro: Poliestireno (OS) e Poli (metacrilato de metila) (PMAM) que foram dopadas com Óleo de Buriti (OB) em diferentes concentrações, a saber, 8.08%, 14.96%, 34.55% e 46.81%. outras concentrações de óleo foram tentadas, mas sem êxito, pois o óleo não conseguiu se fixar na matriz polimérica. Observamos que as amostras incorporaram de forma intersticial o óleo, alterando sua transparência natural e incorporando uma coloração de cor variável entre o amarelo claro ao alaranjado, dependendo da concentração. A partir de medidas ópticas percebemos que os polímeros passaram a apresentar propriedades semelhantes as do óleo como o fenômeno de emissão a partir da excitação por ultravioleta, confirmando assim a sua presença no interior dos plásticos. Caracterizamos os compósitos também através da constante dielétrica e difusividade térmica em função da temperatura. Essas medidas revelaram o comportamento do sistema formado pelo óleo + polímero e identificamos a mudança de estado físico (líquido ↔ sólido) sofrida pelas micro-gotas de óleo dentro da matriz.

Free radical entrapment and crystallinity of resin composites after accelerated aging as a function of the expiration date

This study evaluated the spin concentration and the crystallinity in different classifications of dental composites as a function of the material condition (new, aged and expired). Specimens were obtained according to the factors: composites: Filtek P60, Filtek Z250, Filtek Z350XT, and Filtek Silorane; and material conditions: new, aged, and expired. The syringe composites underwent an accelerated aging protocol (Arrhenius model). The magnetic properties of the composites were characterized using Electron Paramagnetic Resonance (EPR) and the concentration of spins (number of spins/mass) was calculated. The crystallinity of the composites tested was characterized with X-ray diffraction (XRD). Filtek P60 and Filtek Z250 presented similarities in terms of spin concentration and crystallinity, irrespective of the material condition. The aging protocol influenced the composite Filmic Z350XT that exhibited a significant increase in the spin concentration. Besides, lower intensity peaks of the organic matrix and amorphous silica were also observed for both aged and expired Filtek Z350XT. Although a significant lower spin concentration was observed for the silorane composite in comparison to that of the methacrylates, a decrease in the relative intensity of peaks of the amorphous region related to the organic components in the diffractograms was observed. The material conditions tested influence the crystallinity and the magnetic properties of the composites evaluated. (C) 2014 Elsevier Ltd. All rights reserved.

Characterization of a polymer-infiltrated ceramic-network material

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Viscoelastic Behavior of Multiwalled Carbon Nanotubes into Phenolic Resin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of Decomposition Kinetics of Poly (Ether-Ether-Ketone) by Thermogravimetric Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sugarcane bagasse cellulose fibres and their hydrous niobium phosphate composites: synthesis and characterization by XPS, XRD and SEM

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tricot stitched carbon fiber reinforced polymer composite laminates manufactured by resin transfer molding process: C-scan and flexural analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Bacterial cellulose as a template for preparation of hydrotalcite-like compounds

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)