Physical, Geochemical, Geomechanical, Geophysical and Hydrodynamic Characterization and Anisotropy Assessment of Corvio Sandstone

Corvio sandstone is a ~20 m thick unit (Corvio Formation) that appears in the top section of the Frontada Formation (Campoó Group; Lower Cretaceous) located in Northern Spain in the southern margin of the Basque-Cantabrian Basin. Up to 228 plugs were cored from four 0.3 x 0.2 x 0.5 m blocks of Corvio sandstone, to perform a comprehensive characterization of the physical, mineralogical, geomechanical, geophysical and hydrodynamic properties of this geological formation, and the anisotropic assessment of the most relevant parameters. Here we present the first data set obtained on 53 plugs which covers (i) basic physical and chemical properties including density, porosity, specific surface area and elementary analysis (XRF - CHNS); (ii) the curves obtained during unconfined and confined strengths tests, the tensile strengths, the calculated static elastic moduli and the characteristic stress levels describing the brittle behaviour of the rock; (iii) P- and S-wave velocities (and dynamic elastic moduli) and their respective attenuation factors Qp and Qs, electrical resistivity for a wide range of confining stress; and (iv) permeability and transport tracer tests. Furthermore, the geophysical, permeability and transport tests were additionally performed along the three main orthogonal directions of the original blocks, in order to complete a preliminary anisotropic assessment of the Corvio sandstone.

Data compilation on the biological response to ocean acidification: environmental and experimental context of data sets and related literature

The exponential growth of studies on the biological response to ocean acidification over the last few decades has generated a large amount of data. To facilitate data comparison, a data compilation hosted at the data publisher PANGAEA was initiated in 2008 and is updated on a regular basis (doi:10.1594/PANGAEA.149999). By January 2015, a total of 581 data sets (over 4 000 000 data points) from 539 papers had been archived. Here we present the developments of this data compilation five years since its first description by Nisumaa et al. (2010). Most of study sites from which data archived are still in the Northern Hemisphere and the number of archived data from studies from the Southern Hemisphere and polar oceans are still relatively low. Data from 60 studies that investigated the response of a mix of organisms or natural communities were all added after 2010, indicating a welcomed shift from the study of individual organisms to communities and ecosystems. The initial imbalance of considerably more data archived on calcification and primary production than on other processes has improved. There is also a clear tendency towards more data archived from multifactorial studies after 2010. For easier and more effective access to ocean acidification data, the ocean acidification community is strongly encouraged to contribute to the data archiving effort, and help develop standard vocabularies describing the variables and define best practices for archiving ocean acidification data.

Sediment, water and biomass characteristics along gradients in Kongsfjorden, Svalbard

In contrast to numerous studies on the biomass of marine microphytobenthos from temperate coastal ecosystems, little is known from polar regions. Therefore, microphytobenthos biomass was measured at several coastal sites in Arctic Kongsfjorden (Spitsbergen) during the polar summer (June-August 2006). On sandy sediments, chla varied between 8 and 200 mg/m**2 and was related to water depth, current/wave exposure and geographical location. Biomass was rather independent of abiotic parameters such as sediment properties, salinity, temperature or light availability. At three stations, sediments at water depths of 3-4, 10, 15, 20 and 30 m were investigated to evaluate the effect of light availability on microalgae. Significant differences in distribution patterns of biomass in relation to deeper waters >10 m were found. The productive periods were not as distinct as phytoplankton blooms. Only at 3-4 m water depth at all three stations were two- to threefold increases of biomass measured during the investigation period. Hydrodynamic conditions seemed to be the driving force for differences in sediment colonisation by benthic microalgae. In spite of the extreme Arctic environmental conditions for algal growth, microphytobenthos biomass was comparable to marine temperate waters.

Lithological and chemical composition, stages of sediment accumulation, and sedimentation rates in Core PSh24-2537, West Gotland Basin, Baltic Sea

We studied the grain-size, mineral and chemical compositions, physical properties, radiocarbon age, spore-pollen spectra, and diatom composition in sediments from Core PSh24-2537 sampled in the West Gotland Basin. Four lithological-stratigraphic units were distinguished: varved clays of the Baltic Ice Lake, black and black-gray (sulfide) clays of the Yoldian Sea, gray clays of Ancylus Lake, and greenish-gray sapropel-like littorine and post-littorine silts of the marine stage of Holocene. These units differ from each other both in their matter composition and in plant remains. In the littorine silts organic carbon concentra¬tion reached from 1.5 to 10.35%. Conditions of sediment accumulation and the stages of evolution of the West Gotland Basin over the post-glacial time are characterized.

(Table 2) Petrophysical, petrological, and geochemical characteristics of ODP Hole 163-990A sediments

Ocean Drilling Program Hole 990A penetrated 131 m of subaerially emplaced Paleocene flood basalts on the Southeast Greenland margin with a recovery of 74%. Shipboard P-wave velocity (Vp), density, and magnetic susceptibility were measured with 2- to 15-cm intervals on the core. Individual flow units were divided into four zones based on the observed petrophysical characteristics. From the top, these are Zone I (<7 m thick with a Vp of ~2.5 km/s), Zone II (3-5 m thick with a strongly increasing Vp from 2.5 to 5.5 km/s), Zone III (up to 20 m thick with a Vp of ~5.5-6.0 km/s), and Zone IV (<2 m thick with a strongly decreasing Vp from 6.0 to 2.5 km/s). Eighteen samples were selected from three of the fourteen penetrated basalt units for geochemical, petrological, and petrophysical studies focusing on the altered, low-velocity upper lava Zones I and II. Zone I is strongly altered to >50% clay minerals (smectite) and iron hydroxides, and the petrophysical properties are primarily determined by the clay properties. Zone II is intermediately altered with 5%-20% clay minerals, where the petrophysical properties are a function of both the degree of alteration and porosity variations. Shipboard and shore-based measurements of the same samples show that storage permanently lowers the elastic moduli of basalt from Zones I to III. This is related to the presence of even small quantities of swelling clays. The data show that alteration processes are important in determining the overall seismic properties of flood basalt constructions. The degree and depth of alteration is dependent on the primary lava flow emplacement structures and environment. Thus, the interplay of primary emplacement and secondary alteration structures determine the elastic properties of basalt piles. Rock property theories for sand-clay systems are further used to model the physical property variations in these altered crystalline rocks.

Development of Zirconia based phosphors for application in lighting and as luminescent bioprobes

The strong progress evidenced in photonic and optoelectronic areas, accompanied by an exponential development in the nanoscience and nanotechnology, gave rise to an increasing demand for efficient luminescent materials with more and more exigent characteristics. In this field, wide band gap hosts doped with lanthanide ions represent a class of luminescent materials with a strong technological importance. Within wide band gap material, zirconia owns a combination of physical and chemical properties that potentiate it as an excellent host for the aforementioned ions, envisaging its use in different areas, including in lighting and optical sensors applications, such as pressure sensors and biosensors. Following the demand for outstanding luminescent materials, there is also a request for fast, economic and an easy scale-up process for their production. Regarding these demands, laser floating zone, solution combustion synthesis and pulsed laser ablation in liquid techniques are explored in this thesis for the production of single crystals, nanopowders and nanoparticles of lanthanides doped zirconia based hosts. Simultaneously, a detailed study of the morphological, structural and optical properties of the produced materials is made. The luminescent characteristics of zirconia and yttria stabilized zirconia (YSZ) doped with different lanthanide ions (Ce3+ (4f1), Pr3+ (4f2), Sm3+ (4f5), Eu3+ (4f6), Tb3+ (4f8), Dy3+ (4f9), Er3+ (4f11), Tm3+ (4f12), Yb3+ (4f13)) and co-doped with Er3+,Yb3+ and Tm3+,Yb3+ are analysed. Besides the Stokes luminescence, the anti- Stokes emission upon infrared excitation (upconversion and black body radiation) is also analysed and discussed. The comparison of the luminescence characteristics in materials with different dimensions allowed to analyse the effect of size in the luminescent properties of the dopant lanthanide ions. The potentialities of application of the produced luminescent materials in solid state light, biosensors and pressure sensors are explored taking into account their studied characteristics.

Impact of natural and/or chemical stressors on the freeze-tolerant and euryhaline enchytraeid, Enchytraeus albidus

Rapid climatic changes are taking place in Arctic, subarctic and cold temperate regions, where predictions point to an increase in freeze-thaw events, changes in precipitation, evaporation and salinity patterns. Climate change may therefore result in large impacts in ecosystem functioning and dynamics, especially in the presence of contaminants due to intense anthropogenic activities. Even though multiple stress approaches have received increasing interest in the last decades, the number of such studies is limited. In particular, knowledge on the effect of freezethaw events and salinity fluctuations on ecotoxicology of soil invertebrates is lacking, especially important when considering supralittoral species. Therefore, the aim of this thesis was to investigate the effects of low temperature and salinity fluctuations, singly and in combination with contaminants, in the freeze-tolerant and euryhaline enchytraeid Enchytraeus albidus. The assessment of population level endpoints (survival and reproduction), along with physiological and biochemical parameters such as levels of cryoprotectants, ice/water content, oxidative stress biomarkers, cellular energy allocation, and tissue concentration of chemicals (when applied), provided new and valuable knowledge on the effects of selected physical and chemical stressors in E. albidus, and allowed the understanding of adjustments in the primary response mechanisms that enable worms to maintain homeostasis and survival in harsh environments such as polar and temperate-cold regions. The presence of moderate levels of salinity significantly increased freeze-tolerance (mainly evaluated as survival, cryoprotection and ice fraction) and reproduction of E. albidus. Moreover, it contributed to the readjustments of cryoprotectant levels, restoration of antioxidant levels and changed singnificantly the effect and uptake of chemicals (copper cadmium, carbendazim and 4-nonylphenol). Temperature fluctuations (simulated as daily freeze-thaw cycles, between -2ºC and -4ºC) caused substancial negative effect on survival of worms previsouly exposed to non-lethal concentrations of 4-nonylphenol, as compared with constant freezing (-4ºC) and control temperature (2ºC). The decrease in cryoprotectants, increase in energy consumption and the highest concentration of 4-nonylphenol in the tissues have highlighted the high energy requirements and level of toxicity experienced by worms exposed to the combined effect of contaminants and freezing-thawing events. The findings reported on this thesis demonstrate that natural (physical) and chemical stressors, singly or in combination, may alter the dynamics of E. albidus, affecting not only their survival and reproduction (and consequent presence/distribution) but also their physiological and biochemical adaptations. These alterations may lead to severe consequences for the functioning of the ecosystems along the Arctic, subarctic and cold temperate regions, where they play an important role for decomposition of dead organic matter. This thesis provides a scientific basis for improving the setting of safety factors for natural soil ecosystems, and to underline the integration of similar investigations in ecotoxicology, and eventually in risk assessment of contaminants.

Extended use of gamma irradiation in wild mushrooms conservation: validation of 2 kGy dose to preserve their chemical characteristics

Irradiation is recognized by international organizations as a conservation technology, and its application to wild mushrooms has been tested in some species. Our research group evaluated the effectiveness of gamma irradiation to conserve different samples of highly appreciated species, particularly, Lactarius deliciosus, Macrolepiota procera, Boletus edulis and Hydnum repandum. From those results and considering also international recommendations on this subject, the 2 kGy dose was chosen for further studies. Therefore, the application of gamma irradiation at 2 kGy dose was extended to Boletus pinophilus Pilát & Dermek and Clitocybe subconnexa Murrill to validate the proposed technology. Considering the obtained results, some of the analysed chemical parameters (specially sugars and fatty acids), as well as the antioxidant activity, showed significant changes after irradiation treatment, particularly in B. pinophillus, probably due to its higher water content. Nevertheless, the obtained differences did not seem to be sufficient to change the organoleptic characteristics of these mushrooms. Furthermore, the antioxidant activity was generally higher in irradiated samples. In conclusion, the detected chemical changes might be considered as acceptable, when considering the high advantages of gamma irradiation at decontamination and/or disinfestation level.

An Examination of Psychological Meaningfulness, Safety, and Availability as the Underlying Mechanisms linking Job Features and Personal Characteristics to Work Engagement

The present study tested a nomological net of work engagement that was derived from its extant research. Two of the main work engagement models that have been presented and empirically tested in the literature, the JD-R model and Kahn’s model, were integrated to test the effects that job features and personal characteristics can have on work engagement through the psychological conditions of meaningfulness, safety, and availability. In this study, safety refers to psychological perceptions of safety and not workplace safety behaviors. The job features that were tested in this model included person-job fit, autonomy, co-worker relations, supervisor support, procedural justice, and interactional justice, while the personal characteristics consisted of self-consciousness, self-efficacy, extraversion, and neuroticism. Thirty-four hypotheses and a conceptual model were tested in order to establish the viability of this nomological net of work engagement in which it was expected that meaningfulness would mediate the relationships between job features and work engagement, safety would mediate the relationships that job features and personal characteristics have with work engagement, and availability (physical, emotional, and cognitive resources) would mediate the relationships that personal characteristics have with work engagement. Furthermore, analyses were run in order to determine the factor structure of work engagement, assess whether or not it exhibits differential validity from organizational commitment and job satisfaction, and confirm that it is positively related to the outcome variable of organizational citizenship behavior (OCB). The final sample consisted of 500 workers from an online labor market who responded to a questionnaire composed of measures of all constructs included in this study. Findings show that work engagement is best represented as a three-factor construct, composed of vigor, dedication and absorption. Furthermore, support was found for the distinction of work engagement from the related constructs of organizational commitment and job satisfaction. With regard to the proposed model, meaningfulness proved to be the strongest predictor of work engagement. Results show that it partially mediates the relationships that all job features have with work engagement. Safety proved to be a partial mediator of the relationships that autonomy, co-worker relations, supervisor support, procedural justice, interactional justice, and self-efficacy have with work engagement, and fully mediate the relationship between neuroticism and work engagement. Findings also show that availability partially mediates the positive relationships that extraversion and self-efficacy have with work engagement, and fully mediates the negative relationship that neuroticism has with work engagement. Finally, a positive relationship was found between work engagement and OCB. Research and organizational implications are discussed.

A comparative study of the structural, mechanical and tribological characteristics of TiSiC-Cr coatings prepared in CH4 and C2H2 reactive atmosphere by cathodic vacuum arc

TiSiC-Cr coatings, with Cr and Si as additional elements, were deposited on Si, C 45 and 316 L steel substrates via cathodic arc evaporation. Two series of coatings with thicknesses in the range of 3.6–3.9 μm were produced, using either CH4 or C2H2 as carbon containing gas. For each series, different coatings were prepared by varying the carbon rich gas flow rate between 90 and 130 sccm, while maintaining constant cathode currents (110 and 100 A at TiSi and Cr cathodes, respectively), substrate bias (–200 V) and substrate temperature (∼320 °C). The coatings were analyzed for their mechanical characteristics (hardness, adhesion) and tribological performance (friction, wear), along with their elemental and phase composition, chemical bonds, crystalline structure and cross-sectional morphology. The coatings were found to be formed with nano-scale composite structures consisting of carbide crystallites (grain size of 3.1–8.2 nm) and amorphous hydrogenated carbon. The experimental results showed significant differences between the two coating series, where the films formed from C2H2 exhibited markedly superior characteristics in terms of microstructure, morphology, hardness, friction behaviour and wear resistance. For the coatings prepared using CH4, the measured values of crystallite size, hardness, friction coefficient and wear rate were in the ranges of 7.2–8.2 nm, 26–30 GPa, 0.3–0.4 and 2.1–4.8 × 10−6 mm3 N−1 m−1, respectively, while for the coatings grown in C2H2, the values of these characteristics were found to be in the ranges of 3.1–3.7 nm, 41–45 GPa, 0.1–0.2 and 1.4–3.0 × 10−6 mm3 N−1 m−1, respectively. Among the investigated coatings, the one produced using C2H2 at the highest flow rate (130 sccm) exhibited the highest hardness (45.1 GPa), the lowest friction coefficient (0.10) and the best wear resistance (wear rate of 1.4 × 10−6 mm3 N−1 m−1).

Biotic and abiotic parameters that distinguish types of temporary ponds in a Portuguese Mediterranean ecosystem

Temporary ponds are seasonal wetland habitats subjected to extreme and unstable ecological conditions. Some are classified as priority habitats for conservation by the European Union Habitats Directive. Our study area was the coastal plain of southwest Portugal, which spans across 100km north to south and hosts a large number of temporary ponds as a consequence of climatic and edaphic characteristics. Field sampling of floristic and edaphic data was carried out in 24 temporary ponds every spring between 2005 and 2008. We recorded a total of 174 plant species identified within visually homogeneous plots. We included the data in a geographic information system and classified ponds according to their floristic composition, using a biotic regionalization analysis based on species presence/absence, which is a practical and unambiguous criterion. We found three significantly different groups of ponds which corresponded to an eco-physiognomic pond typology: Mediterranean temporary ponds, marshlands, and disturbed ponds. For the first two pond types we defined characteristic or indicator plant species. We searched also for relationships between pond type and a series of large-scale climatic, geographic, and geological variables, as well as local-scale physical and chemical properties of the soil. Pond type was distinguished by a complex combination of some of these variables, including environmental energy, soil texture, nitrogen content of the soil and pH. A practical way of discriminating between different

Physical modeling and numerical simulations of degradation mechanisms in devices and insulators for power applications

In this thesis, a TCAD approach for the investigation of charge transport in amorphous silicon dioxide is presented for the first time. The proposed approach is used to investigate high-voltage silicon oxide thick TEOS capacitors embedded in the back-end inter-level dielectric layers for galvanic insulation applications. In the first part of this thesis, a detailed review of the main physical and chemical properties of silicon dioxide and the main physical models for the description of charge transport in insulators are presented. In the second part, the characterization of high-voltage MIM structures at different high-field stress conditions up to the breakdown is presented. The main physical mechanisms responsible of the observed results are then discussed in details. The third part is dedicated to the implementation of a TCAD approach capable of describing charge transport in silicon dioxide layers in order to gain insight into the microscopic physical mechanisms responsible of the leakage current in MIM structures. In particular, I investigated and modeled the role of charge injection at contacts and charge build-up due to trapping and de-trapping mechanisms in the oxide layer to the purpose of understanding its behavior under DC and AC stress conditions. In addition, oxide breakdown due to impact-ionization of carriers has been taken into account in order to have a complete representation of the oxide behavior at very high fields. Numerical simulations have been compared against experiments to quantitatively validate the proposed approach. In the last part of the thesis, the proposed approach has been applied to simulate the breakdown in realistic structures under different stress conditions. The TCAD tool has been used to carry out a detailed analysis of the most relevant physical quantities, in order to gain a detailed understanding on the main mechanisms responsible for breakdown and guide design optimization.

[association Between Physical And Psychosocial Impacts Of Oral Disorders And Quality Of Life Among The Elderly].

This study sought to evaluate the association between the impact of oral disorders in terms of physical/psychosocial dimensions and quality of life among the elderly. It involved a cross-sectional study conducted among the elderly (65-74 years) in 2008/2009. The social impact was assessed using the Oral Health Impact Profile (OHIP 14) and the quality of life using the SF 12 Short-Form Health Survey. Descriptive, univariate and multivariate (logistic regression) analysis was conducted with correction for the design effect, using SPSS(r)18.0 software. Of the 800 individuals approached, 736 elderly individuals participated (TR = 92%), with a mean age of 67.77 years, the majority of whom showed no impact based on the measurement of the prevalence of OHIP. The functional limitation dimension of the OHIP was associated with the physical domain of the SF12, irrespective of the other variables investigated. However, the seriousness of OHIP and its psychological discomfort and disability dimensions was associated with the mental domain of the SF12. The conclusion reached is that some impacts of oral disorders were associated with unsatisfactory quality of life in the physical and mental domains.