Laboratory verification of predicted permanent deformation in asphalt materials following climate change.

In the past a change in temperature of 5°C most often occurred over intervals of thousands of years. According to estimates by the IPCC, in the XXI century is expected an increase in average temperatures in Europe between 1.8 and 4.0°C in the best case caused by emissions of carbon dioxide and other GHG from human activities. As well as on the environment and economic context, global warming will have effects even on road safety. Several studies have already shown how increasing temperature may cause a worsening of some types of road surface damages, especially rutting, a permanent deformation of the road structures consisting in the formation of a longitudinal depression in the wheelpath, mostly due to the rheological behavior of bitumen. This deformation evolves during the hot season because of the heating capacity of the asphalt layers, in fact, the road surface temperature is up to 24°C higher than air. In this thesis, through the use of Wheeltrack test, it was studied the behavior of some types of asphalt concrete mixtures subjected to fatigue testing at different temperatures. The objectives of this study are: to determine the strain variation of different bituminous mixture subjected to fatigue testing at different temperature conditions; to investigate the effect of aggregates, bitumen and mixtures’ characteristics on rutting. Samples were made in the laboratory mostly using an already prepared mixtures, the others preparing the asphalt concrete from the grading curve and bitumen content. The same procedure was performed for each specimen: preparation, compaction using the roller compactor, cooling and heating before the test. The tests were carried out at 40 - 50 - 60°C in order to obtain the evolution of deformation with temperature variation, except some mixtures for which the tests were carried out only at 50°C. In the elaboration of the results were considered testing parameters, component properties and the characteristics of the mixture. Among the testing parameters, temperature was varied for each sample. The mixtures responded to this variation with a different behavior (linear logarithmic and exponential) not directly correlated with the asphalt characteristics; the others parameters as load, passage frequency and test condition were kept constant. According to the results obtained, the main contribution to deformation is due to the type of binder used, it was found that the modified bitumen have a better response than the same mixtures containing traditional bitumen; to the porosity which affects negatively the behavior of the samples and to the homogeneity ceteris paribus. The granulometric composition did not seem to have interfered with the results. Overall has emerged at working temperature, a decisive importance of bitumen composition, than the other characteristics of the mixture, that tends to disappear with heating in favor of increased dependence of rutting resistance from the granulometric composition of the sample considered. In particular it is essential, rather than the mechanical characteristics of the binder, its chemical properties given by the polymeric modification. To confirm some considered results, the maximum bulk density and the air voids content were determined. Tests have been conducted in the laboratories of the Civil Engineering Department at NTNU in Trondheim according to European Standards.

Functional Genomics and Cell Biology of the Dolphin (Tursiops runcatus): Establishment of Novel Molecular Tools to Study Marine Mammals in Changing Environments

The dolphin (Tursiops truncatus) is a mammal that is adapted to life in a totally aquatic environment. Despite the popularity and even iconic status of the dolphin, our knowledge of its physiology, its unique adaptations and the effects on it of environmental stressors are limited. One approach to improve this limited understanding is the implementation of established cellular and molecular methods to provide sensitive and insightful information for dolphin biology. We initiated our studies with the analysis of wild dolphin peripheral blood leukocytes, which have the potential to be informative of the animal’s global immune status. Transcriptomic profiles from almost 200 individual samples were analyzed using a newly developed species-specific microarray to assess its value as a prognostic and diagnostic tool. Functional genomics analyses were informative of stress-induced gene expression profiles and also of geographical location specific transcriptomic signatures, determined by the interaction of genetic, disease and environmental factors. We have developed quantitative metrics to unambiguously characterize the phenotypic properties of dolphin cells in culture. These quantitative metrics can provide identifiable characteristics and baseline data which will enable identification of changes in the cells due to time in culture. We have also developed a novel protocol to isolate primary cultures from cryopreserved tissue of stranded marine mammals, establishing a tissue (and cell) biorepository, a new approach that can provide a solution to the limited availability of samples. The work presented represents the development and application of tools for the study of the biology, health and physiology of the dolphin, and establishes their relevance for future studies of the impact on the dolphin of environmental infection and stress.

Preliminary studies for the establishment of a tsunami early detection algorithm to be used in the frame of a Tsunami Warning System

This thesis presents and discusses TEDA, an algorithm for the automatic detection in real-time of tsunamis and large amplitude waves on sea level records. TEDA has been developed in the frame of the Tsunami Research Team of the University of Bologna for coastal tide gauges and it has been calibrated and tested for the tide gauge station of Adak Island, in Alaska. A preliminary study to apply TEDA to offshore buoys in the Pacific Ocean is also presented.

Performance evaluation of low environmental impact asphalt concretes using the mechanistic empirical design method based on laboratory fatigue and permanent deformation models

The "sustainability" concept relates to the prolonging of human economic systems with as little detrimental impact on ecological systems as possible. Construction that exhibits good environmental stewardship and practices that conserve resources in a manner that allow growth and development to be sustained for the long-term without degrading the environment are indispensable in a developed society. Past, current and future advancements in asphalt as an environmentally sustainable paving material are especially important because the quantities of asphalt used annually in Europe as well as in the U.S. are large. The asphalt industry is still developing technological improvements that will reduce the environmental impact without affecting the final mechanical performance. Warm mix asphalt (WMA) is a type of asphalt mix requiring lower production temperatures compared to hot mix asphalt (HMA), while aiming to maintain the desired post construction properties of traditional HMA. Lowering the production temperature reduce the fuel usage and the production of emissions therefore and that improve conditions for workers and supports the sustainable development. Even the crumb-rubber modifier (CRM), with shredded automobile tires and used in the United States since the mid 1980s, has proven to be an environmentally friendly alternative to conventional asphalt pavement. Furthermore, the use of waste tires is not only relevant in an environmental aspect but also for the engineering properties of asphalt [Pennisi E., 1992]. This research project is aimed to demonstrate the dual value of these Asphalt Mixes in regards to the environmental and mechanical performance and to suggest a low environmental impact design procedure. In fact, the use of eco-friendly materials is the first phase towards an eco-compatible design but it cannot be the only step. The eco-compatible approach should be extended also to the design method and material characterization because only with these phases is it possible to exploit the maximum potential properties of the used materials. Appropriate asphalt concrete characterization is essential and vital for realistic performance prediction of asphalt concrete pavements. Volumetric (Mix design) and mechanical (Permanent deformation and Fatigue performance) properties are important factors to consider. Moreover, an advanced and efficient design method is necessary in order to correctly use the material. A design method such as a Mechanistic-Empirical approach, consisting of a structural model capable of predicting the state of stresses and strains within the pavement structure under the different traffic and environmental conditions, was the application of choice. In particular this study focus on the CalME and its Incremental-Recursive (I-R) procedure, based on damage models for fatigue and permanent shear strain related to the surface cracking and to the rutting respectively. It works in increments of time and, using the output from one increment, recursively, as input to the next increment, predicts the pavement conditions in terms of layer moduli, fatigue cracking, rutting and roughness. This software procedure was adopted in order to verify the mechanical properties of the study mixes and the reciprocal relationship between surface layer and pavement structure in terms of fatigue and permanent deformation with defined traffic and environmental conditions. The asphalt mixes studied were used in a pavement structure as surface layer of 60 mm thickness. The performance of the pavement was compared to the performance of the same pavement structure where different kinds of asphalt concrete were used as surface layer. In comparison to a conventional asphalt concrete, three eco-friendly materials, two warm mix asphalt and a rubberized asphalt concrete, were analyzed. The First Two Chapters summarize the necessary steps aimed to satisfy the sustainable pavement design procedure. In Chapter I the problem of asphalt pavement eco-compatible design was introduced. The low environmental impact materials such as the Warm Mix Asphalt and the Rubberized Asphalt Concrete were described in detail. In addition the value of a rational asphalt pavement design method was discussed. Chapter II underlines the importance of a deep laboratory characterization based on appropriate materials selection and performance evaluation. In Chapter III, CalME is introduced trough a specific explanation of the different equipped design approaches and specifically explaining the I-R procedure. In Chapter IV, the experimental program is presented with a explanation of test laboratory devices adopted. The Fatigue and Rutting performances of the study mixes are shown respectively in Chapter V and VI. Through these laboratory test data the CalME I-R models parameters for Master Curve, fatigue damage and permanent shear strain were evaluated. Lastly, in Chapter VII, the results of the asphalt pavement structures simulations with different surface layers were reported. For each pavement structure, the total surface cracking, the total rutting, the fatigue damage and the rutting depth in each bound layer were analyzed.

Tetracycline-inducible RNAi Knockdown of SCL (Stem Cell Leukaemia) in Mice

RNAi (RNA interference) is a powerful technology for sequence-specific targeting of mRNAs. This thesis was aimed at establishing conditions for conditional RNAi-mediated silencing first in vitro and subsequently also in transgenic mice. As a target the basic helix-loop-helix transcription factor encoding gene SCL (stem cell leukaemia also known as Tal-1 or TCL5) was used. SCL is a key regulator for haematopoietic development and ectopic expression of SCL is correlated with acute T-lymphoblastic leukaemias. Loss of SCL function studies demonstrated that ab initio deletion of SCL resulted in embryonic lethality around day E9 in gestation. To be able to conditionally inactivate SCL, RNAi technology was combined with the tetracycline-dependent regulatory system. This strategy allowed to exogenously control the induction of RNAi in a reversible fashion and consequently the generation of a completely switchable RNAi knockdown. First a suitable vector allowing for co-expression of tetracycline-controlled shRNAs (small hairpin RNAs) and constitutively active EGFP (enhanced green fluorescent protein) was generated. This novel vector, pRNAi-EGFP, was then evaluated for EGFP expression and tetracycline-mediated expression of shRNAs. Four sequences targeting different regions within the SCL mRNA were tested for their efficiency to specifically knockdown SCL. These experiments were performed in M1 murine leukaemia cells and subsequently in the HEK 293 cell line, expressing an engineered HA-tagged SCL protein. The second assay provided a solid experimental method for determining the efficiency of different SCL-siRNA knockdown constructs in tissue culture. Western blotting analyses revealed a down regulation of SCL protein for all four tested SCL-specific target sequences albeit with different knockdown efficiencies (between 25% and 100%). Furthermore, stringent tetracycline-dependent switchability of shRNA expression was confirmed by co-transfecting the SCL-specific pRNAi-EGFP vector (SCL-siRNA) together with the HA-tagged SCL expression plasmid into the HEK 293TR /T-REx cell line constitutively expressing the tetracycline repressor (TetR). These series of experiments demonstrated tight regulation of siRNA expression without background activity. To be able to control the SCL knockdown in vivo and especially to circumvent any possible embryonic lethality a transgenic mouse line with general expression of a tetracycline repressor was needed. Two alternative methods were used to generate TetR mice. The first approach was to co-inject the tetracycline-regulated RNAi vector together with a commercially available and here specifically modified T-REx expression vector (SCL-siRNA T-REx FRT LoxP mouse line). The second method involved the generation of a TetR expressor mouse line, which was then used for donating TetR-positive oocytes for pronuclear injection of the RNAi vector (SCL-siRNA T-REx mouse line). As expected, and in agreement with data from conditional Cre-controlled adult SCL knockout mice, post-transcriptional silencing of SCL by RNAi caused a shift in the maturation of red blood cell populations. This was shown in the bone marrow and peripheral blood by FACS analysis with the red blood cell-specific TER119 and CD71 markers which can be used to define erythrocyte differentiation (Lodish plot technique). In conclusion this study established conditions for effective SCL RNAi-mediated silencing in vitro and in vivo providing an important tool for further investigations into the role of SCL and, more generally, of its in vivo function in haematopoiesis and leukaemia. Most importantly, the here acquired knowledge will now allow the establishment of other completely conditional and reversible knockdown phenotypes in mice.

Nonlinear Observers for Sensorless Control of Permanent Magnet Synchronous Motors

In this thesis, the industrial application of control a Permanent Magnet Synchronous Motor in a sensorless configuration has been faced, and in particular the task of estimating the unknown “parameters” necessary for the application of standard motor control algorithms. In literature several techniques have been proposed to cope with this task, among them the technique based on model-based nonlinear observer has been followed. The hypothesis of neglecting the mechanical dynamics from the motor model has been applied due to practical and physical considerations, therefore only the electromagnetic dynamics has been used for the observers design. First observer proposed is based on stator currents and Stator Flux dynamics described in a generic rotating reference frame. Stator flux dynamics are known apart their initial conditions which are estimated, with speed that is also unknown, through the use of the Adaptive Theory. The second observer proposed is based on stator currents and Rotor Flux dynamics described in a self-aligning reference frame. Rotor flux dynamics are described in the stationary reference frame exploiting polar coordinates instead of classical Cartesian coordinates, by means the estimation of amplitude and speed of the rotor flux. The stability proof is derived in a Singular Perturbation Framework, which allows for the use the current estimation errors as a measure of rotor flux estimation errors. The stability properties has been derived using a specific theory for systems with time scale separation, which guarantees a semi-global practical stability. For the two observer ideal simulations and real simulations have been performed to prove the effectiveness of the observers proposed, real simulations on which the effects of the Inverter nonlinearities have been introduced, showing the already known problems of the model-based observers for low speed applications.

Das moderne Buch: Harry Graf Kesslers Ästhetik der Lebenskunst im Spiegel der Großherzog Wilhelm Ernst Ausgabe deutscher Klassiker

Die Großherzog Wilhelm Ernst Ausgabe deutscher Klassiker wurde seit 1904 bis in die Zwanziger Jahre hinein im Insel Verlag in Leipzig publiziert. Die Buchreihe hat nicht nur für den Verlag und die Druckerei Poeschel in der sie gedruckt wurde eine ganze Reihe von Neuerungen nach sich gezogen, auch für den deutschen Buchmarkt hat die Klassikerausgabe einen Meilenstein bedeutet. Sie hat einige Eigenschaften des Taschenbuches vorweggenommen. Sie orientierte sich an der Qualität bibliophiler Buchpublikationen, aber war dennoch preislich erschwinglich. Zeitgenössische Klassikerausgaben erschienen zumeist mit einem Kommentar. Nicht so die Großherzog Wilhelm Ernst Ausgabe. Der Text wurde zwar von führenden Wissenschaftlern editiert, aber sie war dennoch unkommentiert. Der Text war in einer Jenson-Antiqua gesetzt obwohl die Debatte um individuell gestaltete Künstlerschriften und die Diskussion um die als deutsche Schrift begriffene Fraktur unter den wichtigsten Protagonisten des deutschen Buchgewerbes ihren Höhepunkt noch nicht erreicht hatte. Ziel für die Klassikerausgabe war darüber hinaus, das zur Jahrhundertwende leicht angestaubte Image der Stadt Weimar aufzupolieren. Über das Patronat des Großherzogs hinaus hätte man die Gewinne aus dem Verkauf der Bücher der Permanenten Ausstellung für die Anschaffung von modernen Kunstobjekten zur Verfügung stellen wollen, die unter der Leitung von Harry Graf Kessler stand. Sieht man den Inhalt der Werke der in der Klassikerreihe erschienen Dichter Goethe, Schiller und Körner in einem ästhetischen Kontext mit dem der Philosophen Schopenhauer und Kant, wird im Spiegel der Formalästhetik der Klassikerausgabe Graf Kesslers Bildungs- und Kulturbegriff erkennbar, der sich in den Jahren nach der Jahrhundertwende zu seinem Lebenskunstideal verdichtete. Der zerrütteten Existenz der Zeitgenossen, wie Friedrich Nietzsche sie beschrieben hatte, sollte der Inhalt der Ausgabe in seiner modernen Form eine moderne Wertehaltung entgegensetzen. Die Lektüre der Klassiker sollte den deutschen Philister „entkrampfen“ und ihm ein Stück der verloren geglaubten Lebensfreude wieder zurück bringen, in dem dieser auch die Facetten des Lebensleids als normal hinnehmen und akzeptieren lernte. Die Klassikerausgabe repräsentierte aus diesem Grund auch den kulturellen und politischen Reformwillen und die gesellschaftlichen Vorstellungen die der Graf für ein modernes Deutschland als überfällig erachtete. Die Buchreihe war aus diesem Grund auch ein politisches Statement gegen die Beharrungskräfte im deutschen Kaiserreich. Die Klassikerreihe wurde in der buchhistorischen Forschung zwar als bedeutender Meilenstein charakterisiert und als „wichtiges“ oder gar „revolutionäres“ Werk der Zeit hervorgehoben, die Ergebnisse der Forschung kann man überspitzt aber in der Aussage zusammenfassen, dass es sich bei der Großherzog Wilhelm Ernst Ausgabe um einen „zufälligen Glückstreffer“ deutscher Buchgestaltung zu handeln scheint. Zumindest lassen die Aussagen, die bisher in dieser Hinsicht gemacht wurden, keine eindeutige Einordnung zu, außer vielleicht der, dass die Klassiker von der englischen Lebensreform inspiriert wurden und Henry van de Velde und William Morris einen Einfluss auf ihre äußere Form hatten. Gerade die Gedankenansätze dieser Beiden nutzte Graf Kessler aber für eigene Überlegungen, die ihn schließlich auch zu eigenen Vorstellungen von idealer Buchgestaltung brachten. Da für Kessler auch Gebrauchsgegenstände Kunst sein konnten, wird das Konzept der Klassikerausgabe bis zur Umsetzung in ihrer `bahnbrechenden´ Form in das ideengeschichtliche und ästhetische Denken des Grafen eingeordnet. Die Klassiker werden zwar in buchhistorischen Einzeluntersuchungen bezüglich ihrer Komponenten, dem Dünndruckpapier, ihrem Einband oder der Schrifttype exponiert. In buchwissenschaftlichen Überblicksdarstellungen wird ihr Einfluss hingegen weniger beachtet, denn verschiedene Kritiker bezogen sie seit ihrem ersten Erscheinen nicht als deutsches Kulturgut mit ein, denn sie lehnten sowohl die englischen Mitarbeiter Emery Walker, Edward Johnston, Eric Gill und Douglas Cockerell wie auch ihre Gestaltung als „welsche“ Buchausgabe ab. Richtig ist, die Großherzog Wilhelm Ernst Ausgabe hatte dieselbe Funktion wie die von Graf Kessler in Weimar konzipierten Kunstausstellungen und die dortige Kunstschule unter der Leitung seines Freundes Henry van de Velde. Auch das für Weimar geplante Theater, das unter der Leitung von Hugo von Hofmannsthal hätte stehen sollen und die Großherzog Wilhelm Ernst Schule, hätten dieselben Ideen der Moderne mit anderen Mitteln transportieren sollen, wie die Großherzog Wilhelm Ernst Ausgabe deutscher Klassiker.

Non-Linear Analysis and Design of Synchronous Bearingless Multiphase Permanent Magnet Machines and Drives

A two-dimensional model to analyze the distribution of magnetic fields in the airgap of a PM electrical machines is studied. A numerical algorithm for non-linear magnetic analysis of multiphase surface-mounted PM machines with semi-closed slots is developed, based on the equivalent magnetic circuit method. By using a modular structure geometry, whose the basic element can be duplicated, it allows to design whatever typology of windings distribution. In comparison to a FEA, permits a reduction in computing time and to directly changing the values of the parameters in a user interface, without re-designing the model. Output torque and radial forces acting on the moving part of the machine can be calculated. In addition, an analytical model for radial forces calculation in multiphase bearingless Surface-Mounted Permanent Magnet Synchronous Motors (SPMSM) is presented. It allows to predict amplitude and direction of the force, depending on the values of torque current, of levitation current and of rotor position. It is based on the space vectors method, letting the analysis of the machine also during transients. The calculations are conducted by developing the analytical functions in Fourier series, taking all the possible interactions between stator and rotor mmf harmonic components into account and allowing to analyze the effects of electrical and geometrical quantities of the machine, being parametrized. The model is implemented in the design of a control system for bearingless machines, as an accurate electromagnetic model integrated in a three-dimensional mechanical model, where one end of the motor shaft is constrained to simulate the presence of a mechanical bearing, while the other is free, only supported by the radial forces developed in the interactions between magnetic fields, to realize a bearingless system with three degrees of freedom. The complete model represents the design of the experimental system to be realized in the laboratory.

Continuous-Flow Magnetic Separation with Permanent Magnets for Water Treatment

More efficient water treatment technologies would decrease the water bodies’ pollution and the actual intake of water resource. The aim of this thesis is an in-depth analysis of the magnetic separation of pollutants from water by means of a continuous-flow magnetic filter subjected to a field gradient produced by permanent magnets. This technique has the potential to improve times and efficiencies of both urban wastewater treatment plants and drinking water treatment plants. It might also substitute industrial wastewater treatments. This technique combines a physico-chemical phase of adsorption and a magnetic phase of filtration, having the potential to bond magnetite with any conventional adsorbent powder. The removal of both Magnetic Activated Carbons (MACs) and zeolite-magnetite mix with the addition of a coagulant was investigated. Adsorption tests of different pollutants (surfactants, endocrine disruptors, Fe(III), Mn(II), Ca(II)) on these adsorbents were also performed achieving good results. The numerical results concerning the adsorbent removals well reproduced the experimental ones obtained from two different experimental setups. In real situations the treatable flow rates are up to 90 m3/h (2000 m3/d).

In vivo performance of a laser fluorescence device for the approximal detection of caries in permanent molars

OBJECTIVES: The aim of this randomised clinical trial was to investigate if a laser fluorescence device is able to discriminate between sound and carious approximal sites and between enamel and dentinal lesions, as well as to find appropriate cut-off values. METHODS: One hundred and seventeen sound or uncavitated carious sites in permanent molars were visually and radiographically examined, then either opened or not, after which their laser fluorescence was measured. Forty-three lesions were opened, the caries removed and the clinically identified caries depths were registered in addition to the radiographical scoring. Seventy-four sites were radiographically deemed sound or had enamel caries and were not opened. Here, the radiographical scorings were registered. RESULTS: Taking the radiographic scoring as gold standard for all investigated approximal sites, sound sites (D(0), n=40) showed significantly lower laser fluorescence measurements than carious sites (D(1-4), n=77) (Mann-Whitney test, P<0.025) suggesting a cut-off at 7 (sensitivity=0.68, specificity=0.7). Comparing measurements of D(0-2) (n=74) and D(3,4) (n=43), the results were also different by a statistically significant amount (P<0.025) and the cut-off calculated to be 16 (sensitivity=0.6, specificity=0.84). A fair positive correlation between laser fluorescence values and radiographical scoring was found (rho=+0.47, P<0.01). Analysing the 43 opened lesions with their clinically found lesion depths as gold standard, there was a fair positive correlation to the laser fluorescence values (rho=+0.34, P=0.03) and a moderately strong correlation to the radiographic scoring (rho=+0.67, P<0.01). CONCLUSION: The device may be an adjunct tool in the approximal detection of caries along with established procedures.

Hand and ultrasonic instrumentation for orthograde root canal treatment of permanent teeth

Root canal treatment is a frequently performed dental procedure and is carried out on teeth in which irreversible pulpitis has led to necrosis of the dental pulp. Removal of the necrotic tissue remnants and cleaning and shaping of the root canal are important phases of root canal treatment. Treatment options include the use of hand and rotary instruments and methods using ultrasonic or sonic equipment. OBJECTIVES: The objectives of this systematic review of randomized controlled trials were to determine the relative clinical effectiveness of hand instrumentation versus ultrasonic instrumentation alone or in conjunction with hand instrumentation for orthograde root canal treatment of permanent teeth. MATERIAL AND METHODS: The search strategy retrieved 226 references from the Cochrane Oral Health Group Trials Register (7), the Cochrane Central Register of Controlled Trials (CENTRAL) (12), MEDLINE (192), EMBASE (8) and LILACS (7). No language restriction was applied. The last electronic search was conducted on December 13th, 2007. Screening of eligible studies was conducted in duplicate and independently. RESULTS: Results were to be expressed as fixed-effect or random-effects models using mean differences for continuous outcomes and risk ratios for dichotomous outcomes with 95% confidence intervals. Heterogeneity was to be investigated including both clinical and methodological factors. No eligible randomized controlled trials were identified. CONCLUSIONS: This review illustrates the current lack of published or ongoing randomized controlled trials and the unavailability of high-level evidence based on clinically relevant outcomes referring to the effectiveness of ultrasonic instrumentation used alone or as an adjunct to hand instrumentation for orthograde root canal treatment. In the absence of reliable research-based evidence, clinicians should base their decisions on clinical experience, individual circumstances and in conjunction with patients' preferences where appropriate. Future randomized controlled trials might focus more closely on evaluating the effectiveness of combinations of these interventions with an emphasis on not only clinically relevant, but also patient-centered outcomes.

Permanent teeth with horizontal root fractures after dental trauma. A retrospective study

The purpose of the present retrospective study was to evaluate the post-traumatic healing of the pulp and periodontium of 32 permanent teeth with horizontal root fractures. Twenty-nine patients, 8-48 years old, who presented at our department with a root fracture between January 2001 and April 2007, participated in the study. Root-fractured teeth with a loosened or dislocated coronal fragment were repositioned and splinted for 14-49 days (average: 34 days). In cases of severe dislocation of the coronal fragment, prophylactic endodontic treatment was performed. Follow-up examinations were conducted routinely after 1,2,3,6, and 12 months. For this study, follow-up took place for up to 7 years post trauma. Of 32 root-fractured teeth, 29 (91%) survived. 10 teeth (31%) exhibited pulpal healing; 13 teeth (41%) were prophylactically endodontically treated within 2 weeks of injury. At the fracture line, interposition of calcified tissue was evident in 6 teeth (19%), and interposition of granulation tissue was observed in 8 teeth (25%). The prognosis of the root-fractured teeth was good, and one-third of the teeth with root fractures possessed a vital pulp at the final examination.