Relay card for capacitance measurements

In this bachelor's thesis a relay card for capacitance measurements was designed, built and tested. The study was made for the research and development laboratory of VTI Technologies, which manufactures capacitive silicon micro electro mechanical accelerometers and pressure sensors. As the size of the sensors is decreasing the capacitance value of the sensors also decreases. The decreased capacitance causes a need for new and more accurate measurement systems. The technology used in the instrument measuring the capacitance dictates a framework how the relay card should be designed, thus the operating principle of the instrument must be known. To achieve accurate results the measurement instrument and its functions needed to be used correctly. The relay card was designed using printed circuit board design methods that minimize interference coupling to the measurement. The relay card that was designed in this study is modular. It consists of a separate CPU card, which was used to control the add-on cards connected to it. The CPU card was controlled from a computer through a serial bus. Two add-on cards for the CPU card were designed in this study. The first one was the measurement card, which could be used to measure 32 capacitive sensors. The second add-on card was the MUX card, which could be used to switch between two measurement cards. The capacitance measurements carried out through the MUX card and the measurement cards were characterized with a series of test measurements. The test measurement data was then analysed. The relay card design was confirmed to work and offer accurate measurement results up to a measurement frequency of 10 MHz. The length of the measurement cables limited the measurement frequency.

Assistance circulatoire chronique: le point en 2013 [Long-term mechanical circulatory support: where do we stand in 2013?].

With the advent of new technologies, experience with long-term mechanical circulatory support (MCS) is rapidly growing. Candidates to MCS are selected based on concepts, strategies and classifications that are specific to this indication. As results drastically improve, supported by stronger scientific evidence, the trend is towards earlier implantation. An adequate pre-implant follow-up is mandatory in order to avoid missing the best window of opportunity for implantation. While on chronic support, the hemodynamic profile of patients with continuous-flow ventricular assist devices is unique and remarkably influenced by the hydration status. Optimal management of these patients from the pre-implant phase to the long-term support phase requires a multidisciplinary approach that is similar to that already long validated for organ transplantation.

Influence of the quality of nursing on the duration of weaning from mechanical ventilation in patients with chronic obstructive pulmonary disease.

OBJECTIVE: To evaluate the influence of nursing on the duration of weaning from mechanical ventilation in patients with chronic obstructive pulmonary disease. DESIGN: Data were collected prospectively over a 1-yr period (study year) and compared with previously collected prospective data recorded in our chronic obstructive pulmonary disease database during a 5-yr period. SETTING: The medical intensive care unit (ICU) of a university hospital. PATIENTS: Eighty-seven patients with chronic obstructive pulmonary disease. Fifteen patients had chronic obstructive pulmonary disease that required mechanical ventilation for acute exacerbation of their disease (study year), and 72 were patients with chronic obstructive pulmonary disease from the previously collected data. INTERVENTIONS: The ICU course (duration of mechanical ventilation, mortality) was recorded, as well as several respiratory parameters (pulmonary function tests and arterial blood gases in stable conditions, and nutritional status), and they were compared with an "index of nursing." MEASUREMENTS AND MAIN RESULTS: We developed an "index of nursing", comparing the effective workforce of the nurses (number and qualifications) with the ideal workforce required by the number of patients and the severity of their diseases. A value of 1.0 represented a perfect match between the needed and the effectively present nurses, whereas a lesser value signified a diminished available workforce. This index was compared with the complications and duration of weaning from mechanical ventilation. During the first 5 yrs, the duration of mechanical ventilation increased progressively from 7.3 +/- 8.0 to 38.2 +/- 25.8 days (p = .006). A significant inverse correlation between the duration of mechanical ventilation and the nursing index (p = .025) was found. In the sixth comparative year, the number of nurses increased (nursing index = 1.05) and the duration of mechanical ventilation decreased to 9.9 +/- 13 days (p < .001, yr 5 vs. yr 6). CONCLUSIONS: The quality of nursing appears to be a measurable and critical factor in the weaning from mechanical ventilation of patients with chronic obstructive pulmonary disease. Below a threshold in the available workforce of ICU nurses, the weaning duration of patients with chronic obstructive pulmonary disease increases dramatically. Therefore, very close attention should be given to the education and number of ICU nurses.

Heterogeneous 40Ar* distributions in naturally deformed muscovite: in situ UV-laser ablation evidence for micro structurally controlled intragrain diffusion

Micas are commonly used in Ar-40/Ar-39 thermochronological studies of variably deformed rocks yet the physical basis by which deformation may affect radiogenic argon retention in mica is poorly constrained. This study examines the relationship between deformation and deformation-induced microstructures on radiogenic argon retention in muscovite, A combination of furnace step-heating and high-spatial resolution in situ UV-laser ablation Ar-40/Ar-39 analyses are reported for deformed muscovites sampled from a granitic pegmatite vein within the Siviez-Mischabel Nappe, western Swiss Alps (Penninic domain, Brianconnais unit). The pegmatite forms part of the Variscan (similar to 350 Ma) Alpine basement and exhibits a prominent Alpine S-C fabric including numerous mica `fish' that developed under greenschist facies metamorphic conditions, during the dominant Tertiary Alpine tectonic phase of nappe emplacement. Furnace step-heating of milligram quantities of separated muscovite grains yields an Ar-40/Ar-39 age spectrum with two distinct staircase segments but without any statistical plateau, consistent with a previous study from the same area. A single (3 X 5 mm) muscovite porphyroclast (fish) was investigated by in situ UV-laser ablation. A histogram plot of 170 individual Ar-40/Ar-39 UV-laser ablation ages exhibit a range from 115 to 387 Ma with modes at approximately 340 and 260 Ma. A variogram statistical treatment of the (40)Ad/Ar-39 results reveals ages correlated with two directions; a highly correlated direction at 310 degrees and a lesser correlation at 0 degrees relative to the sense of shearing. Using the highly correlated direction a statistically generated (Kriging method) age contour map of the Ar-40/Ar-39 data reveals a series of elongated contours subparallel to the C-surfaces which where formed during Tertiary nappe emplacement. Similar data distributions and slightly younger apparent ages are recognized in a smaller mica fish. The observed intragrain age variations are interpreted to reflect the partial loss of radiogenic argon during Alpine (similar to 35 Ma) greenschist facies metamorphism. One-dirnensional diffusion modelling results are consistent with the idea that the zones of youngest apparent age represent incipient shear band development within the mica porphyroclasts, thus providing a network of fast diffusion pathways. During Alpine greenschist facies metamorphism the incipient shear bands enhanced the intragrain loss of radiogenic argon. The structurally controlled intragrain age variations observed in this investigation imply that deformation has a direct control on the effective length scale for argon diffusion, which is consistent with the heterogeneous nature of deformation. (C) 2001 Elsevier Science B.V. All rights reserved.

Biomechanical characterization and in vitro mechanical injury of elderly human femoral head cartilage: comparison to adult bovine humeral head cartilage.

OBJECTIVES: In vitro mechanical injury of articular cartilage is useful to identify events associated with development of post-traumatic osteoarthritis (OA). To date, many in vitro injury models have used animal cartilage despite the greater clinical relevance of human cartilage. We aimed to characterize a new in vitro injury model using elderly human femoral head cartilage and compare its behavior to that of an existing model with adult bovine humeral head cartilage. DESIGN: Mechanical properties of human and bovine cartilage disks were characterized by elastic modulus and hydraulic permeability in radially confined axial compression, and by Young's modulus, Poisson's ratio, and direction-dependent radial strain in unconfined compression. Biochemical composition was assessed in terms of tissue water, solid, and glycosaminoglycan (GAG) contents. Responses to mechanical injury were assessed by observation of macroscopic superficial tissue cracks and histological measurements of cell viability following single injurious ramp loads at 7 or 70%/s strain rate to 3 or 14 MPa peak stress. RESULTS: Confined compression moduli and Young's moduli were greater in elderly human femoral cartilage vs adult bovine humeral cartilage whereas hydraulic permeability was less. Radial deformations of axially compressed explant disks were more anisotropic (direction-dependent) for the human cartilage. In both cartilage sources, tissue cracking and associated cell death during injurious loading was common for 14 MPa peak stress at both strain rates. CONCLUSION: Despite differences in mechanical properties, acute damage induced by injurious loading was similar in both elderly human femoral cartilage and adult bovine humeral cartilage, supporting the clinical relevance of animal-based cartilage injury models. However, inherent structural differences such as cell density may influence subsequent cell-mediated responses to injurious loading and affect the development of OA.

Micro-Crédito em Cabo Verde e sua Contribuição para o Fomento do Empreendedorismo

Esta pesquisa consiste num estudo sobre o micro-crédito em Cabo Verde, no âmbito do fomento do empreendedorismo, na perspectiva de geração de emprego e rendimentos, com a finalidade de complementar o mercado de trabalho no fomento de empregos e criação de empreendimentos sustentáveis. Procura-se compreender e analisar a dinâmica dos empreendimentos económicos financiados no sector do micro-crédito, na ilha de Santiago, a partir da observação empírica da sua estrutura organizacional. Uma vez que, mudanças económicas sentidas nas últimas décadas foram marcadas pela lógica excludente do mercado capitalista, com marcas profundas de degradação do aparelho do Estado a nível social, pelo aumento do desemprego e da precarização do trabalho, nesse contexto, os empreendimentos procuram, de certa forma, completar o vazio deixado, na medida em que esta poderá ser a via para incentivar as camadas mais pobres das populações a criarem os seus próprios negócios. Nessa prespectiva, as micro-empresas desempenham um papel fundamental na promoção do emprego, inovação, criação de rendimentos e no desenvolvimento económico e social. As fundamentações práticas baseiam-se no estudo feito junto à OMCV, onde analisou-se trabalho desenvolvido pela OMCV no que toca as políticas e os programas de micro-crédito que vem desenvolvendo ao longo da sua actividade, destacando os beneficiários do programa de micro-crédito da OMCV. É oportuno análisar o micro-crédito como ferramenta de fomento ao empreendedorismo. Ampliar os serviços de micro-crédito como uma pirâmide social visa atingir as desigualdades e exclusão social, factores que contribuem para o crescimento e desenvolvimento económico. A inclusão social através do empreenndedorismo, tem sido objecto de estudo nas económias capitalistas, visando desenvolver o empreendedorismo como das alternativas para o crescimento e desenvolvimento económico. Neste sentido, o micro-crédito pode ser um instrumento de amplo alcance às comunidades de baixa rendimento, na promoção de mudanças sociais. Por fim, são deixadas algumas considerações e uma conclusão acerca do trabalho efectuado.

New record of Pterotaenia fasciata (Wiedemann) (Diptera, Ulidiidae) in Brazil, a probably mechanical vector of enteric bacteria

Pterotaenia fasciata is commonly recorded in rural areas in Argentina, but during a Diptera survey study developed in a reservoir which retains storm water from polluted canals in an urban area of Taboão da Serra municipality, SP, Brazil, we could capture P. fasciata adults. Enteric bacteria Escherichia coli T. Escherich, 1885 and Proteus sp. were isolated from P. fasciata collected in traps inside the reservoir and around it. Fecal coliforms and E. coli were found in the water of the reservoir. These records suggest that a high abundance of this species at urban areas with inadequate sewage canals should reveal these muscoid dipterans as mechanical vectors of enteric bacteria.

Micro-patterning of biomolecules on polymer substrates.

UV−excimer laser photoablation was used, in combination with surface blocking techniques, to pattern proteins on the surfaces of polyimide and poly(ethylene terephthalate). This technique involves physical adsorption of avidin through laser-defined openings in low-temperature laminates or adsorbed protein blocking layers. Visualization of biomolecular patterns were monitored using avidin and fluorescein-labeled biotin as a model receptor−ligand couple. Adsorbed proteins could be shown to bind to UV-laser-treated polymer surfaces up to three times higher than on commercially available polymers. UV-laser photoablation was also used for the generation of three-dimensional structure, which leads to the possibility of biomolecule patterning within polymer-based microanalytical systems. The simplicity and easy handling of the described technique facilitate its application in microdiagnostic devices.

Inequality over the business cycle: Estimating income risk using micro-data on consumption

We use CEX repeated cross-section data on consumption and income, to evaluate the nature of increased income inequality in the 1980s and 90s. We decompose unexpected changes in family income into transitory and permanent, and idiosyncratic and aggregate components, and estimate the contribution of each component to total inequality. The model we use is a linearized incomplete markets model, enriched to incorporate risk-sharing while maintaining tractability. Our estimates suggest that taking risk sharing into account is important for the model fit; that the increase in inequality in the 1980s was mainly permanent; and that inequality is driven almost entirely by idiosyncratic income risk. In addition we find no evidence for cyclical behavior of consumption risk, casting doubt on Constantinides and Duffie s (1995) explanation for the equity premium puzzle.

Creative accounting: Some ethical issues of macro- and micro-manipulation

This paper examines two principal categories of manipulative behaviour. The term'macro-manipulation' is used to describe the lobbying of regulators to persuadethem to produce regulation that is more favourable to the interests of preparers.'Micro-manipulation' describes the management of accounting figures to produce abiased view at the entity level. Both categories of manipulation can be viewed asattempts at creativity by financial statement preparers. The paper analyses twocases of manipulation which are considered in an ethical context. The paperconcludes that the manipulations described in it can be regarded as morallyreprehensible. They are not fair to users, they involve an unjust exercise ofpower, and they tend to weaken the authority of accounting regulators.

MICRO CRÉDITO EM CABO VERDE PAPEL DO MICRO-CRÉDITO NO COMBATE A POBREZA EM SANTA CATARINA

O funcionamento do sistema financeiro tradicional leva à exclusão de determinadas categorias como é o caso das populações de baixo rendimento. A intervenção pública, por meio dos bancos comerciais, acaba não resolvendo o problema, tanto por questões de alcance como de eficiência. O micro-crédito surgiu no mundo como uma tentativa de eliminar a pobreza pelo acesso ao crédito, recorrendo a estratégias descentralizadas de financiamento. O micro-crédito depois de várias experiências internacionais chegou a Cabo Verde, com o objectivo de promover a inserção socio-económico da mulher, com especial realce, mulheres do meio rural. Este trabalho procura delinear as principais instituições que concede o micro-crédito, como se processa o seu financiamento e o seu impacto no combate à pobreza. Se conclui que, o micro-crédito tem forte impacto na economia Cabo-Verdiana, na medida em que, para além de poder gerar riquezas individuais e para o país contribui de uma forma estratégica, política, socio-económico para o desenvolvimento, de realçar, a luta contra a pobreza.