Hydrogen bonding interactions in poly(ε-caprolactone-dimethyl siloxane-ε-caprolactone)/poly(hydroxyether of bisphenol A) triblock copolymer/homopolymer blends and the effect on crystallization, microphase separation and self-assembly

This study investigated the self-assembled microphase separated morphologies that are obtained in bulk, by the complexation of a semicrystalline poly(ε-caprolactone-dimethyl siloxane-ε-caprolactone) (PCL-PDMS-PCL) triblock copolymer and a homopolymer, poly(hydroxyether of bisphenol A) (PH) in tetrahydrofuran (THF). In these blends, microphase separation takes place due to the disparity in intermolecular interactions; specifically, the homopolymer interacts with PCL blocks through hydrogen bonding interactions. The crystallization, microphase separation and crystalline structures of a triblock copolymer/homopolymer blends were investigated. The phase behavior of the complexes was investigated using small-angle X-ray scattering and transmission electron microscopy. At low PH concentrations, PCL interacts relatively weakly with PH, whereas in complexes containing more than 50 wt% PH, the PCL block interacts significantly with PH, leading to the formation of composition-dependent nanostructures. SAXS and TEM results indicate that the lamellar morphology of neat PCL-PDMS-PCL triblock copolymer changes into disordered structures at 40-60 wt% PH. Spherical microdomains were obtained in the order of 40-50 nm in complexes with 80 wt% PH. At this concentration, the complexes show a completely homogenous phase of PH/PCL, with phase-separated spherical PDMS domains. The formation of these nanostructures and changes in morphology depends on the strength of hydrogen bonding between PH/PCL blocks and also the phase separated PDMS blocks.

Impacts of wear and geometry response of the cutting tool on machinability of super austenitic stainless steel

This paper presents a study of tool wear and geometry response whenmachinability tests were applied under milling operations onthe Super Austenitic Stainless Steel alloy AL-6XN. Eight milling trials were executed under two cutting speeds, two feed rates, andtwo depths of cuts. Cutting edge profile measurements were performed to reveal response of cutting edge geometry to the cuttingparameters and wear. A scanning electron microscope (SEM) was used to inspect the cutting edges. Results showed the presenceof various types of wear such as adhesion wear and abrasion wear on the tool rake and flank faces. Adhesion wear represents theformation of the built-up edge, crater wear, and chipping, whereas abrasion wear represents flank wear.Thecommonly formed wearwas crater wear. Therefore, the optimum tool life among the executed cutting trails was identified according to minimum lengthand depth of the crater wear.The profile measurements showed the formation of new geometries for the worn cutting edges due toadhesion and abrasion wear and the cutting parameters.The formation of the built-up edge was observed on the rake face of thecutting tool. The microstructure of the built-up edge was investigated using SEM. The built-up edge was found to have the austeniteshear lamellar structure which is identical to the formed shear lamellae of the produced chip.

Modulated deformation of lipid membrane to vesicles and tubes due to reduction of graphene oxide substrate under laser irradiation

Biomembrane transformations are closely related to many biological processes including endo/exocytosis and the cellular response to the local physical environment. In this work, we investigated the transformation between lipid membranes and lipid vesicles/tubes modulated by the solid substrate of graphene oxide (GO) aggregates under laser irradiation. We firstly fabricate a novel type of lipid@GO composite consisting of micrometer-sized GO aggregates surrounded by lamellar lipid membranes. Upon laser irradiation, lipid protrusion occurs and leads to the formation of vesicles adsorbed on the GO aggregate surface, with an average size as 0.43 times of the radius of GO aggregate. Both the location and the dynamic formation process of vesicles can be modulated. The arising of vesicles prefers to occur at edges of the GO planes rather than on surface of individual GO sheets within the GO aggregate. Furthermore, at a reduced laser power density, the lipid protrusion mainly grows to tubes instead of vesicles. Such transformations from lipid membrane to vesicles and tubes is ascribed to the reduction of GO to reduced-GO (rGO) under laser irradiation, probably along with the release of gases leading to the deformation of lipid membrane surrounding the GO surface.

Estudio molecular en dos hermanas afectadas por ictiosis congénita autosómica recesiva : descripción de una nueva mutación causal en TGM1

Se describe la variante homocigota c.320-2A>G de TGM1 en dos hermanas con ictiosis congénita autosómica recesiva. El clonaje de los transcritos generados por esta variante permitió identificar tres mecanismos moleculares de splicing alternativos.