PHOTOCATALYTIC OXIDATION OF AQUEOUS SOLUTIONS OF JET FUEL AND ICING INHIBITORS

The present paper is devoted to the results of experimental research undertaken into photocatalytical oxidation (PCO) of aqueous solutions of de-icing agents and aqueous extract of jet fuel. The report consists of introduction, literature review, description of materials and methods, discussion of results and conclusions. TiO2 was selected as a photocatalyst for the experiments with synthetic solutions of ethylene glycol, 2-ethoxyethanol and aqueous extract of jet fuel. To explain the PCO mechanisms affecting certain behaviour of de-icing agent under distinctive conditions, the following factors were studied: the impact of initial concentration of pollutant, the role of pH, the presence of tert-butanol as OH·-radicals scavenger and mineral admixtures. PCO under solar radiation performed in two ways: catalysed by irradiated TiO2 slurry or by TiO2 attached to buoyant hollow glass micro-spheres. Special attention was paid to the energy-saving PCO with reduced intensity mixing of the slurry. The effect of PCO was assessed by determination of residual chemical oxygen demand of solution (COD) and by measuring of concentration of glycols. The PCO process efficiency was assumed to be dependent on the TiO2 suspension fractional composition. Thus, the following effects of solutions’ media were viewed: presence of organic admixtures, pH influence, mixing mode during the PCO. The effects of mineral admixtures - Ca2+, Fe3+/2+, Mn2+, SO42- - that are often present in natural and wastewater systems or produced during the degradation of organic pollutants and which can affect the rate of PCO of de-icing agents, were also investigated.

Siistausmassan saostuksessa kiekkosuodattimella käytettävän suodatinväliaineen testaus ja kehittäminen

Työn aiheena on siistausmassan saostuksessa käytettävä kiekkosuodatinväliaine ja tarkoituksena selvittää lankamateriaalien ja pinnoitusaineiden vaikutusta väliaineen likaantumisherkkyyteen ja suodatusteknisiin ominaisuuksiin. Siistauslaitosten ongelmana on suodatinväliaineen likaantuminen massassa olevien tahmo- ja painoväripartikkelien johdosta. Tällä hetkellä siistauslaitosten kiekkosuodatinpussien valmistuksessa käytetään pääasiassa polypropeeni- ja polyvinylideenifluoridimonofilamenttilankoja, joiden lianhylkivyys on osoittautunut huonoksi. Uusiksi lankamateriaaleiksi tutkimuksiin valittiin Easy Kleen I, Easy Kleen II, Hyflon, Halar ja Polyesteri. Tulosten perusteella Easy Kleen I ja II monofilamenttilangoista kudotun suodatinkankaan lianhylkivyys on polypropeeni- ja polyvinylideenifluoridimonofilamenttilangoista kudottua kangasta parempi. Suodatusteknisissä ominaisuuksissa ei materiaalien välillä havaittu merkittävää eroa. Easy Kleen monofilamenttilangat näyttävät soveltuvan myös keittokutistumiltaan ja mekaanisilta ominaisuuksiltaan kiekkosuodatinpussien materiaaleiksi. Polypropeeni- ja polyesterimonofilamenettilangoista kudottujen suodatinkankaiden pinnoittamisessa käytettiin hydrofiilisiä ja hydrofobisia pinnoitusaineita. Tulosten perusteella on mahdollista parantaa suodatinkankaan lianhylkivyyttä pinnoittamalla. Pinnoitettu kangas on myös suodatusteknisiltä ominaisuuksiltaan toimiva. Ongelmaksi suodatinkankaiden pinnoittamisessa saattaa kuitenkin muodostua pinnoituslämpötila, jossa kangas kutistuu asennuskelvottomaksi.

Sisäisten donorien vaikutus Polypropeeni Ziegler-Natta katalyytissä

Tässä työssä tutkittiin erilaisten sisäisten donorien vaikutusta polypropeenin ominaisuuksiin käytettäessä Ziegler-Natta-katalyyttiä, joka valmistettiin Borealiksen aiemmin kehittämällä kaksifaasimenetelmällä. Tällä uudella menetelmällä katalyytti voidaan valmistaa ilman lisättyä sisäistä donoria ja kantajaa. Katalyyttihiukkaset saadaan kaksifaasisysteemin ansiosta muodoltaan pyöreiksi. Työn kokeellisessa osassa valmistettiin erilaisia Mg-komplekseja, jossa sisäinen donori muodostuu in-situ alkoholin ja karboksyylihappokloridin reagoidessa keskenään. Katalyyttisynteesissä Mg-kompleksi reagoi TiCl4:n kanssa. Saatujen katalyyttien ominaisuuksia testattiin polymeroimalla niillä propeenia 70 °C:ssa tunnin ajan. Polymeerien ominaisuuksia tutkittiin useiden eri karakterisointimenetelmien avulla. Lisäksi tutkittiin mahdollisuutta valmistaa katalyytti, joka ei sisältäisi ftalaattia. Työssä havaittiin, että katalyytin valmistusmenetelmä on käyttökelpoinen myös muilla sisäisillä donoreilla kuin referenssinä käytetyllä DOP:lla. Kaksiliuosfaasi-systeemi saatiin aikaan myös kahdella muulla työssä tutkitulla sisäisellä donorilla. Lisäksi faasitasapainokokeissa kahden liuosfaasin systeemi saatiin aikaan sisäisellä donorilla, joka ei sisältänyt ftalaattia. Kyseisellä katalyytillä havaittiin olevan muista katalyyteistä poikkeavia ominaisuuksia. Esimerkiksi se antoi matalamman isotaktisuuden kuin referenssikatalyytti ja se saattaisikin soveltua matalan isotaktisuuden pehmeille tuotteille. Työssä kokeiltiin yhdellä uudella katalyytillä myös eteenin polymerointia, sillä katalyytin donoripitoisuus oli hyvin matala. Katalyytin aktiivisuus eteenipolymeroinnissa oli varsin hyvä.

Establishment of an In Vitro Photoallergy Test Using NCTC2544 Cells and IL-18 Production

Differentiation between photoallergenic and phototoxic reactions induced by low molecular weight compounds represents a current problem. The use of eratinocytes as a potential tool for the detection of photoallergens as opposed to photoirritants is considered an interesting strategy for developing in vitro methods. We have previously demonstrated the possibility to use the human keratinocyte cell line NCTC2455 and the production of interleukin-18 (IL-18) to screen low molecular weight sensitizers. The purpose of this work was to explore the possibility to use the NCTC2544 assay to identify photoallergens and discriminate from phototoxic chemicals. First, we identified suitable condition of UV-irradiation (3.5 J/cm2) by investigating the effect of UVAirradiation on intracellular IL-18 on untreated or chloropromazine (a representative phototoxic compound)- treated NCTC2544 cells. Then, the effect of UVA-irradiation over NCTC2544 cells treated with increasing concentrations of 15 compounds including photoallergens (benzophenone, 4-ter-butyl-4-methoxydibenzoylmethane, 2-ethylexyl-p-methoxycinnamate, ketoprofen, 6-methylcumarin); photoirritant and photoallergen (4-aminobenzoic acid, chlorpromazine, promethazine); photoirritants (acridine, ibuprofen, 8-methoxypsoralen, retinoic acid); and negative compounds (lactic acid, SDS and p-phenilendiamine) was investigated. Twenty-four hours after exposure, cytotoxicity was evaluated by the MTT assay or LDH leakage, while ELISA was used to measure the production of IL-18. At the maximal concentration assayed with non-cytotoxic effects (CV80 under irradiated condition), all tested photoallergens induced a significant and a dose-dependent increase of intracellular IL-18 following UVA irratiation, whereas photoirritants failed. We suggest that this system may be useful for the in vitro evaluation of the photoallergic potential of chemicals.

Establishment of an in vitro photoassay using THP-1 cells and IL-8 to discriminate photoirritants from photoallergens

At present, there are no in vivo or in vitro methods developed which has been adopted by regulatory authorities to assess photosensitization induced by chemicals. Recently, we have proposed the use of THP-1 cells and IL-8 release to identify the potential of chemicals to induce skin sensitization. Based on the assumption that sensitization and photosensitization share common mechanisms, the aim of this work was to explore the THP-1 model as an in vitro model to identify photoallergenic chemicals. THP-1 cells were exposed to 7 photoallergens and 3 photoirritants and irradiated with UVA light or kept in dark. Non phototoxic allergens or irritants were also included as negative compounds. Following 24 h of incubation, cytotoxicity and IL-8 release were measured. At subtoxic concentrations, photoallergens produced a dose-related increase in IL-8 release after irradiation. Some photoirritants also produced a slight increase in IL-8 release. However, when the overall stimulation indexes of IL-8 were calculated for each chemical, 6 out of 7 photoallergens tested reached a stimulation index above 2, while the entire set of negative compounds had stimulation indexes below 2. Our data suggest that this assay may become a useful cell-based in vitro test for evaluating the photosensitizing potential of chemicals.

Histologic evaluation of thermal damage produced on soft tissues by CO2, Er,Cr:YSGG and diode lasers

Objective: The aim of this in vitro experimental study was to perform histological evaluation of the thermal effect produced on soft tissue irradiated with CO2, Er,Cr:YSGG or diode lasers. Study design: Porcine oral mucosa samples were irradiated with Er,Cr:YSGG laser at 1 W with and without water / air spray, at 2 W with and without water / air spray, and at 4 W with water / air spray, with CO2 laser at 1 W, 2 W, 10 W, 20 W continuous mode and 20 W pulsed mode and diode laser at 2W, 5W, and 10W pulsed mode. The thermal effect was evaluated measuring the width of damaged tissue adjacent to the incision, stained positively for hyalinized tissue with Hematoxylin-Eosin and Masson Trichrome stains. Besides, histological changes in the irradiated tissue were described using subjective grading scales. Results: The evaluated lasers developed a wide range of thermal damage with significant differences between groups. The samples with lowest thermal effect were those irradiated with Er,Cr:YSGG laser using water / air spray, followed by CO2 and diode lasers. Conclusions: Emission parameters of each laser system may influence the thermal damage inflicted on the soft tissue, however, the wave length of each laser determines the absorption rate characteristics of every tissue and the thermal effect

Gas-phase photocatalytic oxidation of volatile organic compounds

Substances emitted into the atmosphere by human activities in urban and industrial areas cause environmental problems such as air quality degradation, respiratory diseases, climate change, global warming, and stratospheric ozone depletion. Volatile organic compounds (VOCs) are major air pollutants, emitted largely by industry, transportation and households. Many VOCs are toxic, and some are considered to be carcinogenic, mutagenic, or teratogenic. A wide spectrum of VOCs is readily oxidized photocatalytically. Photocatalytic oxidation (PCO) over titanium dioxide may present a potential alternative to air treatment strategies currently in use, such as adsorption and thermal treatment, due to its advantageous activity under ambient conditions, although higher but still mild temperatures may also be applied. The objective of the present research was to disclose routes of chemical reactions, estimate the kinetics and the sensitivity of gas-phase PCO to reaction conditions in respect of air pollutants containing heteroatoms in their molecules. Deactivation of the photocatalyst and restoration of its activity was also taken under consideration to assess the practical possibility of the application of PCO to the treatment of air polluted with VOCs. UV-irradiated titanium dioxide was selected as a photocatalyst for its chemical inertness, non-toxic character and low cost. In the present work Degussa P25 TiO2 photocatalyst was mostly used. In transient studies platinized TiO2 was also studied. The experimental research into PCO of following VOCs was undertaken: - methyl tert-butyl ether (MTBE) as the basic oxygenated motor fuel additive and, thus, a major non-biodegradable pollutant of groundwater; - tert-butyl alcohol (TBA) as the primary product of MTBE hydrolysis and PCO; - ethyl mercaptan (ethanethiol) as one of the reduced sulphur pungent air pollutants in the pulp-and-paper industry; - methylamine (MA) and dimethylamine (DMA) as the amino compounds often emitted by various industries. The PCO of VOCs was studied using a continuous-flow mode. The PCO of MTBE and TBA was also studied by transient mode, in which carbon dioxide, water, and acetone were identified as the main gas-phase products. The volatile products of thermal catalytic oxidation (TCO) of MTBE included 2-methyl-1-propene (2-MP), carbon monoxide, carbon dioxide and water; TBA decomposed to 2-MP and water. Continuous PCO of 4 TBA proceeded faster in humid air than dry air. MTBE oxidation, however, was less sensitive to humidity. The TiO2 catalyst was stable during continuous PCO of MTBE and TBA above 373 K, but gradually lost activity below 373 K; the catalyst could be regenerated by UV irradiation in the absence of gas-phase VOCs. Sulphur dioxide, carbon monoxide, carbon dioxide and water were identified as ultimate products of PCO of ethanethiol. Acetic acid was identified as a photocatalytic oxidation by-product. The limits of ethanethiol concentration and temperature, at which the reactor performance was stable for indefinite time, were established. The apparent reaction kinetics appeared to be independent of the reaction temperature within the studied limits, 373 to 453 K. The catalyst was completely and irreversibly deactivated with ethanethiol TCO. Volatile PCO products of MA included ammonia, nitrogen dioxide, nitrous oxide, carbon dioxide and water. Formamide was observed among DMA PCO products together with others similar to the ones of MA. TCO for both substances resulted in the formation of ammonia, hydrogen cyanide, carbon monoxide, carbon dioxide and water. No deactivation of the photocatalyst during the multiple long-run experiments was observed at the concentrations and temperatures used in the study. PCO of MA was also studied in the aqueous phase. Maximum efficiency was achieved in an alkaline media, where MA exhibited high fugitivity. Two mechanisms of aqueous PCO – decomposition to formate and ammonia, and oxidation of organic nitrogen directly to nitrite - lead ultimately to carbon dioxide, water, ammonia and nitrate: formate and nitrite were observed as intermediates. A part of the ammonia formed in the reaction was oxidized to nitrite and nitrate. This finding helped in better understanding of the gasphase PCO pathways. The PCO kinetic data for VOCs fitted well to the monomolecular Langmuir- Hinshelwood (L-H) model, whereas TCO kinetic behaviour matched the first order process for volatile amines and the L-H model for others. It should be noted that both LH and the first order equations were only the data fit, not the real description of the reaction kinetics. The dependence of the kinetic constants on temperature was established in the form of an Arrhenius equation.

Pronóstico y tratamiento de la boca seca. Revisión sistemática

No existen protocolos claramente establecidos para el tratamiento de la boca seca. El objetivo de este trabajo es realizar una revisión sistemática de la literatura médica de los últimos 10 años. Hemos utilizado las palabras: «dry mouth», «prognosis», «treatment» y «dentistry». En una primera búsqueda hemos encontrado 1.450 entradas. Con la restricción «clinical trials OR randomized controlled trial OR systemic reviews» se han reducido a 522, de las que 145 eran metaanálisis y revisiones sistemáticas. Se han eliminado las que no eran pertinentes al tema y han quedado reducidas a 53. Posteriormente se descartaron 24 (8 no pertinentes, 7 revisiones y 9 opiniones personales). De los 29 artículos analizados, 15 son ensayos clínicos controlados, 2 ensayos no controlados, 4 estudios observacionales, 2 revisiones sistemáticas y 5 revisiones. Los enfermos mejor estudiados son los pacientes con síndrome de Sjögren y los pacientes irradiados. El tratamiento se centra en el etiológico, preventivo, sintomático, de estimulación salival local y sistémicos. Podemos concluir que el tratamiento debe ser individualizado, pudiéndose aplicar sustitutos salivales y diferentes técnicas de estimulación mecánica. There are no clearly established protocols for the treatment of dry mouth. The aim of this paper is a systematic review of the literature of the past 10 years using the words «dry mouth», «prognosis», «treatment» and «dentistry». The initial search found 1,450 entries and within the restriction «clinical trials OR randomized controlled trial OR systemic reviews» it has been reduced to 522, which 145 were meta-analysis and systematic reviews. Papers not relevant to the issue were removed reducing the entries to 53. Twenty-four were dismissed (8 irrelevant, 7 reviews without adequate information and 9 personal opinions). Of the 29 items tested, 15 were controlled trials, 2 uncontrolled trials, 4 observational studies, 2 systematic reviews and 5 non systematic reviews. The most studied patients were Sjögren's syndrome and the irradiated patients. Treatments are focused on the etiology, prevention, symptomatic, local salivary stimulation and systemic treatments. It can be concluded that treatment must be individualized, salivary substitutes and mechanical stimulation techniques can be applied.

Thermal increment due to ErCr: YSGG and CO2 laser irradiation of different implant surfaces. A pilot study

Objective: An evaluation and comparison is made of the thermal increment at different implant surfaces during irradiation with CO2 and ErCr:YSGG lasers. Study design: Five threaded and impacted implants with four types of surfaces were inserted in an adult pig rib: two implants with a hydroxyapatite surface (HA)(impacted and threaded, respectively), a machined titanium surface implant (TI mach), a titanium plasma spray surface implant (TPS), and a sandblasted, acid-etched surface implant (SBAE). A 0.5-mm diameter bone defect was made in the implant apical zone, and a type-K thermocouple (Termopar)® was placed in contact with the implant. The implants were irradiated in the coronal zone of each implant with a CO2 (4 W continuous mode) and an ErCr:YSGG laser (1.5 W, pulsed mode) first without and then with refrigeration. The temperature variations at the implant apical surface were recorded. Results: An apical temperature increase was recorded in all cases during CO2 and ErCr:YSGG laser irradiation without refrigeration. However, when the ErCr:YSGG was used with a water spray, a decrease in temperature was observed in all implants. The acid-etched and sandblasted surfaces were those most affected by the thermal changes. Conclusions: The ErCr:YSGG laser with a water spray applied to the sealing cap or coronal zone of the implants does not generate thermal increments in the apical surface capable of adversely affecting osseointegration and the integrity of the peri-implant bone tissue

Orofacial pain of cardiac origin, serial of clinical cases

Objective: To determine the clinical characteristics of the orofacial pain of cardiac origin in patients visited when doing a treadmill exercise test, at the cardiology service of the Can Ruti Hospital in Badalona (Barcelona, Spain). Study design: The sample of that study included thirty patients visiteding when doing a treadmill exercise test, at the cardiology service. The questionnaire has been asked to a sample of 30 patients. Results: Eleven of the 30 patients included in this study presented craniofacial pain before or during the cardiac seizure. The location of the pain was bilateral, non-irradiated at the mandible in all cases. The intensity of the pain was from slight to severe. The frequency of the appearance of the pain was paroxysmal in 8 cases and constant in three cases, and the duration was from a few hours to a maximum of 14 days. Discussion: The cardiac pain in craniofacial structures is usually bilateral, compared to odontogenic pain which is always unilateral. The pain of cardiac origin is considered atypical because of its location, but about the 10 % of the cases, the cardiac ischemia has its primary manifestation in orofacial structures. Conclusions: Eleven patients referred a bilateral non-irradiated mandibular pain, with intensity from slight to severe, and with a paroxystic frequency in eight cases and a constant frequency in three cases. Just one patient referred pain during the treadmill exercise test. In all cases the pain disappeared after the cardiac surgery or the administration of vasodilators.

Apnea-like suppression of respiratory motion: First evaluation in radiotherapy.

BACKGROUND AND PURPOSE: Compensation for respiratory motion is needed while administering radiotherapy (RT) to tumors that are moving with respiration to reduce the amount of irradiated normal tissues and potentially decrease radiation-induced collateral damages. The purpose of this study was to test a new ventilation system designed to induce apnea-like suppression of respiratory motion and allow long enough breath hold durations to deliver complex RT. MATERIAL AND METHODS: The High Frequency Percussive Ventilation system was initially tested in a series of 10 volunteers and found to be well tolerated, allowing a median breath hold duration of 11.6min (range 3.9-16.5min). An evaluation of this system was subsequently performed in 4 patients eligible for adjuvant breast 3D conformal RT, for lung stereotactic body RT (SBRT), lung volumetric modulated arc therapy (VMAT), and VMAT for palliative pleural metastases. RESULTS: When compared to free breathing (FB) and maximal inspiration (MI) gating, this Percussion Assisted RT (PART) offered favorable dose distribution profiles in 3 out of the 4 patients tested. PART was applied in these 3 patients with good tolerance, without breaks during the "beam on time period" throughout the overall courses of RT. The mean duration of the apnea-like breath hold that was necessary for delivering all the RT fractions was 7.61min (SD=2.3). CONCLUSIONS: This first clinical implementation of PART was found to be feasible, tolerable and offers new opportunities in the field of RT for suppressing respiratory motion.

Enhancement of viability of radiosensitive (PBMC) and resistant (MDA-MB-231) clones in low-dose-rate cobalt-60 radiation therapy

AbstractObjective:In the present study, the authors investigated the in vitrobehavior of radio-resistant breast adenocarcinoma (MDA-MB-231) cells line and radiosensitive peripheral blood mononuclear cells (PBMC), as a function of different radiation doses, dose rates and postirradiation time kinetics, with a view to the interest of clinical radiotherapy.Materials and Methods:The cells were irradiated with Co-60, at 2 and 10 Gy and two different exposure rates, 339.56 cGy.min–1 and the other corresponding to one fourth of the standard dose rates, present over a 10-year period of cobalt therapy. Post-irradiation sampling was performed at pre-established kinetics of 24, 48 and 72 hours. The optical density response in viability assay was evaluated and a morphological analysis was performed.Results:Radiosensitive PBMC showed decrease in viability at 2 Gy, and a more significant decrease at 10 Gy for both dose rates. MDAMB- 231 cells presented viability decrease only at higher dose and dose rate. The results showed MDA-MB-231 clone expansion at low dose rate after 48–72 hours post-radiation.Conclusion:Low dose rate shows a possible potential clinical impact involving decrease in management of radio-resistant and radiosensitive tumor cell lines in cobalt therapy for breast cancer.

Immunotherapeutic targeting of LIGHT/LTβR/HVEM pathway fully recapitulates the reduced cytotoxic phenotype of LIGHT-deficient T cells.

Tumor necrosis factor (TNF)/TNF receptor (TNFR) superfamily members play essential roles in the development of the different phases of the immune response. Mouse LIGHT (TNFSF14) is a type II transmembrane protein with a C-terminus extracellular TNF homology domain (THD) that assembles in homotrimers and regulates the course of the immune responses by signaling through 2 receptors, the herpes virus entry mediator (HVEM, TNFSFR14) and the lymphotoxin β receptor (LTβR, TNFSFR3). LIGHT is a membrane-bound protein transiently expressed on activated T cells, natural killer (NK) cells and immature dendritic cells that can be proteolytically cleaved by a metalloprotease and released to the extracellular milieu. The immunotherapeutic potential of LIGHT blockade was evaluated in vivo. Administration of an antagonist of LIGHT interaction with its receptors attenuated the course of graft-versus-host reaction and recapitulated the reduced cytotoxic activity of LIGHT-deficient T cells adoptively transferred into non-irradiated semiallogeneic recipients. The lack of LIGHT expression on donor T cells or blockade of LIGHT interaction with its receptors slowed down the rate of T cell proliferation and decreased the frequency of precursor alloreactive T cells, retarding T cell differentiation toward effector T cells. The blockade of LIGHT/LTβR/HVEM pathway was associated with delayed downregulation of interleukin-7Rα and delayed upregulation of inducible costimulatory molecule expression on donor alloreactive CD8 T cells that are typical features of impaired T cell differentiation. These results expose the relevance of LIGHT/LTβR/HVEM interaction for the potential therapeutic control of the allogeneic immune responses mediated by alloreactive CD8 T cells that can contribute to prolong allograft survival.

Porta-amostras polimérico para espectroscopia infravermelha de sistemas líquidos aquosos ou orgânicos

Infrared spectroscopy laboratories works under permanent care with respect to water contamination, mainly in liquid samples. In this case crystal plates destruction or damage are frequent, increasing the operational expenses. On the other hand, the laboratory which produces such samples must be very careful in drying liquid samples. In this work we develop a simple and inexpensive way to operate in such conditions using polypropylene and HDPE films which were thermally soldered resulting little containers or sample holders. The spectra of sample/sample holder is achieved having the sample holder as background.

Desaluminação do zeólito ofretita por efeito da radiação gama

Protonic offretite samples were modified by gamma-irradiation under different conditions of humidity. The results of infrared spectroscopy and X-ray diffraction reveal that the presence of water is essential to promote dealumination, as the samples irradiated in vacuum only show crystallinity loss. The degree of dealumination is, mainly, controlled by the gamma-irradiation dose while the textural modifications depend also on the percentage of water.