Renewable energies Driven by Feed-on Tariffs. Photovoltaic vs Wind Energy Development in Spain

Although others regulations regarding feed-in tariffs for photovoltaics (PV) existed in Spain previously, the one that meant a paradigm change was the introduction in 2007 of law R.D.661/2007 which established a feed-in tariff of 41,75 cents/kWh if the installed capacity was greater than 100KWp and 44,04 cents/kWh if it was smaller. The high level of the subsidies together with the lack of a limit for the total installed capacity originates the well-known Spanish photovoltaic boom. In September 2008 the installed PV capacity accounted for 3.2GWp (while the official objective stated in the national renewable roadmap was only 400MWp). To avoid this situation a new law, R.D. 1578/2008, was proclaimed which established a decreasing feed-in tariff of 32 cents/kWh (for ground installations) and 34 cents/kWh (for rooftops) and it limited the annual installed capacity to 500MWp. Although it was successful in limiting the PV subsidies total costs, the successive and sudden changes in regulations resulted very harmful to the local PV industry. In this article, the strong influence of feed-in tariff in the development of PV installed capacity and market evolution in Spain will be analyzed in detail. In addition, a comparison with other subsidized technologies which installed capacity has had a smoother evolution, as wind energy, will be presented.

La rehabilitación de construcciones militares para uso hotelero: la red de Paradores de Turismo, (1928-2012)

Fundamento de la tesis: Al comienzo del siglo XX, el interés por el turismo unido a la necesidad de restaurar un abundante patrimonio histórico, posibilitó en España que los poderes públicos se embarcaran en una singular experiencia: la creación de una infraestructura hotelera a partir de la rehabilitación de edificios históricos. La preservación, mantenimiento e incluso rentabilidad de una gran parte del patrimonio español se haría efectiva a través de la innovadora fórmula patrimonio‐turismo, cuya máxima expresión se materializó en la Red de Paradores desde su fundación en la segunda década del siglo pasado hasta nuestros días. Sorprendentemente, este tema no ha sido todavía investigado en su vertiente arquitectónica pese a que España ha sido pionera y modelo en la cuestión de la hotelería pública. Este trabajo aborda el estudio del caso más significativo de todos los edificios de la red, en tanto que el patrimonio que ha servido de base a los fines hoteleros del Estado ha contado con un total de seis tipos arquitectónicos a lo largo de su historia, dentro de los cuales la arquitectura militar despunta con su mayoritaria presencia dentro del contexto de los edificios históricos de la red. El carácter arquetípico de los castillos y fortalezas, arraigado en el inconsciente colectivo, les hizo especialmente atractivos como alojamiento turístico al permitir evocar la remota época medieval, pese a ser el tipo arquitectónico más comprometido para la rehabilitación hotelera. El estudio de las intervenciones operadas en estos inmuebles se revela de forma clara como escaparate de los distintos criterios de intervención patrimonial que se han sucedido en el siglo XX, hasta enlazar con la perspectiva interdisciplinar actual. La tesis abarca en, primer lugar, diferentes aspectos generales relativos al promotor hotelero, la hotelería pública de ámbito nacional e internacional, y la caracterización de los inmuebles de la red estatal española, desde el punto de vista hotelero y arquitectónico, entendida esta última en sus tres escalas de influencia: la arquitectónica, la urbana o paisajística, y la del interiorismo. Se analiza en segundo término la arquitectura militar dentro del contexto de la Red de Paradores, desde la consideración de su transformación hotelera, para lo cual ha sido necesario realizar una clasificación propia, que abarca tanto edificios que respondieron a una estructura de cuartel, como castillos‐palacio, o fortalezas que habían servido a los fines de una orden religiosa militar, además de considerarse las intervenciones en recintos históricos de carácter militar, donde se hacía obligatorio construir de nueva planta. En tercer y último lugar, se analiza a lo largo de las distintas etapas del organismo turístico las rehabilitaciones realizadas en estas construcciones militares, a la vez que se tienen en cuenta las intervenciones en los restantes edificios históricos, para evitar la descontextualización. Este recorrido comienza con la promoción de los dos primeros paradores a cargo del Comisario Regio, el marqués de la Vega‐Inclán, que sirvieron para sentar las bases de los conceptos e ideas que habrían de desarrollarse en las siguientes décadas. Posteriormente, se desarrolló y tomó forma la red con el Patronato Nacional del Turismo, en la que las primeras intervenciones en tipos militares se tradujeron en reformas interiores de locales. La etapa clave de la red, y en particular de la arquitectura militar, tuvo lugar con el Ministerio de Información y Turismo, marcada por la “repristinación” de monumentos, tras un período preparatorio con la Dirección General del Turismo en el que lo militar había quedado de telón de fondo de otros tipos arquitectónicos. Tras el auge del Ministerio llegó el período de decadencia en el que los castillos y fortalezas desaparecieron de los intereses de las Secretarias de Turismo, hasta llegar a las inauguraciones de los novedosos establecimientos del siglo XXI y el resurgimiento del tipo militar con el parador de Lorca. Metodología empleada: Este trabajo de investigación se ha servido fundamentalmente de documentación inédita, procedente de diversos archivos, además de una muy extensa toma de datos in situ. Dentro del patrimonio analizado, los inmuebles que responden al tipo arquitectónico militar se han dividido en tres grandes grupos: inmuebles rehabilitados que entraron en funcionamiento en la red, inmuebles en proceso de transformación hotelera, e inmuebles que fueron adquiridos con fines hoteleros pero que no llegaron a rehabilitarse. Para cada uno de ellos ha sido necesario determinar en qué estado llegaron a manos de la Administración Turística, cuál fue el mecanismo a través del cual se adquirieron, en qué consistió su primera rehabilitación hotelera, y cuáles fueron las ampliaciones o reformas más significativas que se realizaron posteriormente. Estos datos se han sintetizado en fichas y se han extraído conclusiones al comparar cada unidad con el conjunto. Simultáneamente se introdujeron dos factores externos: la historia del turismo que permitió hacer una ordenación cronológica de los inmuebles según etapas, y la historia de la teoría y práctica de la intervención patrimonial en España que permitió comparar los criterios patrimoniales de la Administración competente respecto de las intervenciones de la Administración Turística, cuyo contacto se haría obligatorio a partir del Decreto, de 22 de abril de 1949, que dejaba bajo la tutela del Estado a todos los castillos y fortalezas. Aportación de la tesis: Con carácter general, la tesis centra una ordenación y sistematización completa del patrimonio inmobiliario de la red, desde el punto de vista de los tipos hoteleros y arquitectónicos, además de poner por primera vez en conexión distintos modelos de hotelería pública, para constituirse en el sustrato de futuras investigaciones. El estudio realizado se ha hecho extensivo a las distintas escalas que inciden de forma interconectada en la implantación de un parador: la arquitectónica, la urbana y la del interiorismo, hasta ahora referenciado desde la exclusiva visión arquitectónica. Se han definido las etapas de la historia de la red, no ya sólo a partir del hilo conductor de la cadena sucesiva de organismos turísticos, sino que por primera vez se hace en razón de la evolución que sufren las intervenciones patrimoniales a lo largo del tiempo, a la vez que se entra en conexión con la teoría y praxis de la restauración monumental. Con carácter particular, la arquitectura militar dentro del contexto de los paradores se destaca en el período del Ministerio, en el que se experimentaron todas las posibilidades que presentaba su rehabilitación. En este sentido se ha puesto de manifiesto en este trabajo un tipo híbrido de parador, a caballo entre la rehabilitación y la edificación de nueva planta, las dos formas básicas de establecimiento creadas en la Comisaría Regia, al que se ha denominado edificación de nueva planta en recinto histórico militar. Esta nueva caracterización se ha valorado como la forma más eficiente de implantar paradores, cuyas pautas arquitectónicas abarcaron un abanico de posibilidades: imitación de modelos arquitectónicos históricos con utilización de elementos patrimoniales prestados que dieran el valor de la historia, utilización de un lenguaje moderno, o la inspiración en la arquitectura vernácula. La amalgama de elementos, estilos e intervenciones sucesivas de ampliación fue la característica común tanto para la implantación de un parador en un edificio como en un recinto amurallado. La arquitectura militar transformada en establecimiento hotelero evidencia la vocación escenográfica de las intervenciones patrimoniales, secundada por el interiorismo, además de su aportación a la arquitectura hotelera en lo referente al confort, organización y funcionamiento de sus instalaciones. La tesis ahonda en los diversos aspectos de la rehabilitación hotelera apuntados de forma parcial por algunos autores, y pone de manifiesto la “ambientación medieval” operada en la arquitectura militar, que llegó a tener su máxima expresión con el criterio de la “unidad de estilo” del Ministerio de Información y Turismo. La rehabilitación hotelera dentro del contexto de la Red de Paradores, queda caracterizada en la tesis en relación a intervenciones en construcciones militares, cuya sistematización puede ser extrapolable a otros tipos arquitectónicos o cadenas hoteleras de titularidad pública, a partir del estudio que se ha avanzado en este trabajo. Thesis basis: At the beginning of the 20th century the interest in tourism added to the plentiful heritage in Spain enabled the authorities to embark on a singular experience: the creation of a hotel infrastructure from the restoration of historic buildings. Preservation, maintenance, and even profitability of a large part of the Spanish heritage would be effective through the innovative formula heritage-tourism. Its greatest expression materialized in the Paradores Network since its foundation in last century’s second decade to the present day. Surprisingly, this subject has not yet been investigated in its architectural aspect, even though Spain has been a pioneer and a model in the matter of public hotel business. This project tackles the study of the most significative case of all the network’s buildings, since the heritage which has served throughout history as a base for the State hotel purposes has altogether six architectural types, among which military architecture stands out with its majority presence in the context of the historical buildings of the network. The archetypal character of castles and fortresses, ingrained in the collective subconscious, made them specially attractive for tourist accommodation, as it allowed the evocation of far medieval times, despite being the most awkward architectural type for hotel restoration. The study of the interventions in these buildings clearly reveals itself as a showcase of the different criteria of heritage intervention along the 20th century, connecting to the present interdisciplinary perspective. Firstly, the thesis covers different general aspects regarding the hotel developer, the domestic and international public hotel business, and the description of the Spanish state network buildings from a hotel business and an architectural point of view, the latter from its three influence scales: architectural, urban or landscape, and interior design. Secondly, the transformation of the military architecture in the Paradores Network into hotels is analyzed. For that purpose it was necessary to create a specific classification, which included barrack-structured buildings, castle-palaces, or fortresses which served the purposes of military-religious orders. The interventions in those military historical places where new building became compulsory were also taken into consideration. Thirdly and lastly, the thesis analyses the restorations in these military constructions through the different stages of the tourist organization. In order to avoid decontextualization, interventions in other historical buildings were also considered. This route begins with the promotion of the two first Paradores by the Royal Commissioner, the marquis of Vega-Inclán, which paved the way for the concepts and ideas that were developed in the following decades. Subsequently, the network was developed and took shape with the National Tourism Board. The first interventions on military types were inside refurbishments. The Network’s key period, and in particular of its military architecture, took place with the Ministry of Information and Tourism, a time marked by the “restoration to its original state” of monuments. This stage arrived after a preparatory period with the State Tourist Office, when the military type was left as a backdrop for other architectural types. After the Ministry’s boom arrived a decline, in which castles and fortresses disappeared from the Tourist Department’s interests up to the opening of the 21st century new establishments and the resurgence of the military type with Lorca’s Parador. Methodology: The present research project has mainly used unpublished documentation from several archives and has done an extensive in situ data-gathering. Within the heritage analyzed, military buildings have been divided into three main groups: restored buildings that began to operate in the network, those in process of hotel transformation, and those acquired for hotel purposes, but which did not become restored. In each case, it has been necessary to determine the condition in which they arrived to the Tourist Administration, the procedure by which they were acquired, what their first hotel restoration consisted of, and which their subsequent most significative enlargements and alterations were. These facts have been synthesized in cards, and conclusions were drawn by comparing each unit with the whole. Simultaneously, two external factors were introduced: the history of tourism, that allowed establishing a chronological order according to different periods, and the history of Spanish heritage intervention’s theory and practice, that permitted to compare the heritage criteria from the competent Administration with those of the Tourist Administration’s interventions. Both Administrations came compulsorily into contact after the Decree of 22nd April 1949, by which all castles and fortresses became under the protection of the State. Thesis contribution: In general, the thesis focuses on a complete order and systematization of the network’s heritage buildings from the hotel and architectural types points of view, besides connecting for the first time different public hotel business models, becoming the substratum for future investigations. The study has included the different scales that impact interconnected on the establishment of a Parador: architectural, urban and interior design, only referenced to date from an architectural point of view. The Network’s history stages have been defined according to not only a consecutive series of tourist organizations, but also, and for the first time, to the evolution of heritage interventions over time, thus connecting with the theory and praxis of monumental restoration. In particular, within the Paradores, military architecture stands out in the Ministry’s period, in which all kind of restoration possibilities were explored. In this sense, the present project puts forth a hybrid type of Parador between restoration and new building, the two basic ways of establishment created in the Royal Commission, termed new building in military historic enclosure. This new characterization has been evaluated as the most efficient for establishing Paradores, whose architectonic guidelines include a wide range of possibilities: the imitation of historical architectonic models with use of borrowed heritage components that provide historical value, the use of modern language, or the inspiration in vernacular architecture. The amalgam of elements, styles and consecutive enlargement interventions was the common feature of the establishment of a Parador, both in a building or in a walled enclosure. The military architecture transformed into a hotel establishment gives proof of the scenographic vocation of heritage interventions, supported by interior design, as well as of its contribution to hotel architecture, related to its comfort, organization and the functioning of its facilities. The thesis delves into the diverse aspects of hotel restoration, partially pointed out by several authors, and puts forth the creation of a “medieval atmosphere” in military architecture, which came to its highest expression with the “unitary style” criteria of the Ministry of Information and Tourism. Hotel restoration within the context of the Paradores’ Network is defined in this thesis in relation to interventions in military constructions, whose systemization can be extrapolative to other architectural types or public hotel chains, based on the study which has been put forward in this project.

Analytic free-form lens design for tracking integration in concentrating photovoltaics

In this work the concept of tracking integration in concentrating photovoltaics (CPV) is revisited and developed further. With respect to conventional CPV, tracking integration eliminates the clear separation between stationary units of optics and solar cells, and external solar trackers. This approach is capable of further increasing the concentration ratio and makes high concentrating photovoltaics (> 500x) available for single-axis tracker installations. The reduced external solar tracking effort enables possibly cheaper and more compact installations. Our proposed optical system uses two laterally moving plano-convex lenses to achieve high concentration over a wide angular range of ±24°. The lateral movement allows to combine both steering and concentration of the incident direct sun light. Given the specific symmetry conditions of the underlying optical design problem, rotational symmetric lenses are not ideal for this application. For this type of design problems, a new free-form optics design method presented in previous papers perfectly matches the symmetry. It is derived directly from Fermat's principle, leading to sets of functional differential equations allowing the successive calculation of the Taylor series coeficients of each implicit surface function up to very high orders. For optical systems designed for wide field of view and with clearly separated optical surfaces, this new analytic design method has potential application in both fields of nonimaging and imaging optics.

Modelización y simulación numérica de sistemas geotérmicos planos

En el presente proyecto se estudiará la conveniencia de utilizar simulación numérica para evaluar, diseñar y mejorar el diseño de instalaciones geotérmicas planas. Para ello, se modelizará el conjunto de terreno y sistema geotérmico mediante el acoplamiento de un modelo tridimensional (terreno) y un modelo unidimensional, formado por la red de tubería geotérmica, que estará dispuesta en un plano cuya orientación dependerá de las aplicaciones. Para la simulación numérica se utilizará un software de análisis y resolución por elementos finitos tipo comercial. Finalmente, se definirán unos parámetros geométricos de diseño y, teniendo en cuenta las propiedades térmicas de cada material, se realizarán estudios paramétricos para determinar la influencia de cada grupo de parámetros. Ello requerirá la realización de cientos de simulaciones numéricas que permitirán optimizar el rendimiento de sistemas geotérmicos planos tanto horizontales (soleras), como verticales (muros pantalla). ABSTRACT In this project it is going to be studied the convenience of numerical simulation as to evaluate, design and improve the design of geothermal planar installations. With this purpose, the terrain and the geothermal system will be modeled by coupling a three-dimensional model (terrain) and a one-dimensional model formed by the geothermal piping network disposed in a plane with an orientation which will depend on the applications. For the numerical simulation commercial software of analyzing and resolving by finite elements will be used. Finally, geometric design parameters will be defined, and taking into account the thermal properties of each material, parametric studies will be performed to determine the influence of each group of parameters. This will require the completion of hundreds of numerical simulations which will enhance the performance of both horizontal (slabs) and vertical (diaphragm walls) geothermal systems.

Wind intermittency and CO2 reductions: the case of the spanish power system

Renewable energy sources are believed to reduce drastically greenhouse gas emissions that would otherwise be generated from fossil fuels used to generate electricity. This implies that a unit of renewable energy will replace a unit of fossil-fuel, with its CO2 emissions, on an equivalent basis (with no other effects on the grid). But, the fuel economy and emissions in the existing power systems are not proportional with the electricity production of intermittent sources due to cycling of the fossil fuel plants that make up the balance of the grid (i.e. changing the power output makes thermal units to operate less efficiently). This study focuses in the interactions between wind generation and thermal plants cycling, by establishing the levels of extra fuel use caused by decreased efficiencies of fossil back-up for wind electricity in Spain. We analyze the production of all thermal plants in 2011, studying different scenarios where wind penetration causes major deviations in programming, while we define a procedure for quantifying the carbon reductions by using emission factors and efficiency curves from the existing installations. The objectives are to discuss the real contributions of renewable energies to the environmental targets as well as suggest alternatives that would improve the reliability of future power systems.

Presentation and discussion of the UAM/exercise I-1b: "Pin-Cell Burn-Up Benchmark" with the hybrid method

The aim of this work is to present the Exercise I-1b “pin-cell burn-up benchmark” proposed in the framework of OECD LWR UAM. Its objective is to address the uncertainty due to the basic nuclear data as well as the impact of processing the nuclear and covariance data in a pin-cell depletion calculation. Four different sensitivity/uncertainty propagation methodologies participate in this benchmark (GRS, NRG, UPM, and SNU&KAERI). The paper describes the main features of the UPM model (hybrid method) compared with other methodologies. The requested output provided by UPM is presented, and it is discussed regarding the results of other methodologies.

An open-source simulation tool of grid-connected PV systems.

This paper will present an open-source simulation tool, which is being developed in the frame of an European research project1. The tool, whose final version will be freely available through a website, allows the modelling and the design of different types of grid-connected PV systems, such as large grid-connected plants and building-integrated installations. The tool is based on previous software developed by the IES-UPM2, whose models and energy losses scenarios have been validated in the commissioning of PV projects3 carried out in Spain, Portugal, France and Italy, whose aggregated capacity is nearly 300MW. This link between design and commissioning is one of the key points of tool presented here, which is not usually addressed by present commercial software. The tool provides, among other simulation results, the energy yield, the analysis and breakdown of energy losses, and the estimations of financial returns adapted to the legal and financial frameworks of each European country. Besides, educational facilities will be developed and integrated in the tool, not only devoted to learn how to use this software, but also to train the users on the best design PV systems practices. The tool will also include the recommendation of several PV community experts, which have been invited to identify present necessities in the field of PV systems simulation. For example, the possibility of using meteorological forecasts as input data, or modelling the integration of large energy storage systems, such as vanadium redox or lithium-ion batteries. Finally, it is worth mentioning that during the verification and testing stages of this software development, it will be also open to the suggestions received from the different actors of the PV community, such as promoters, installers, consultants, etc.

Propagation of Cross-Section Uncertainties in Criticality Calculations in the Framework of UAM-Phase I Using MCNPX-2.7e and SCALE-6.1

In the framework of the OECD/NEA project on Benchmark for Uncertainty Analysis in Modeling (UAM) for Design, Operation, and Safety Analysis of LWRs, several approaches and codes are being used to deal with the exercises proposed in Phase I, “Specifications and Support Data for Neutronics Cases.” At UPM, our research group treats these exercises with sensitivity calculations and the “sandwich formula” to propagate cross-section uncertainties. Two different codes are employed to calculate the sensitivity coefficients of to cross sections in criticality calculations: MCNPX-2.7e and SCALE-6.1. The former uses the Differential Operator Technique and the latter uses the Adjoint-Weighted Technique. In this paper, the main results for exercise I-2 “Lattice Physics” are presented for the criticality calculations of PWR. These criticality calculations are done for a TMI fuel assembly at four different states: HZP-Unrodded, HZP-Rodded, HFP-Unrodded, and HFP-Rodded. The results of the two different codes above are presented and compared. The comparison proves a good agreement between SCALE-6.1 and MCNPX-2.7e in uncertainty that comes from the sensitivity coefficients calculated by both codes. Differences are found when the sensitivity profiles are analysed, but they do not lead to differences in the uncertainty.

Assessment of CTF boiling transition and critical heat flux modeling capabilities using the OECD/NRC BFBT and PSBT benchmark databases

Over the last few years, the Pennsylvania State University (PSU) under the sponsorship of the US Nuclear Regulatory Commission (NRC) has prepared, organized, conducted, and summarized two international benchmarks based on the NUPEC data—the OECD/NRC Full-Size Fine-Mesh Bundle Test (BFBT) Benchmark and the OECD/NRC PWR Sub-Channel and Bundle Test (PSBT) Benchmark. The benchmarks’ activities have been conducted in cooperation with the Nuclear Energy Agency/Organization for Economic Co-operation and Development (NEA/OECD) and the Japan Nuclear Energy Safety (JNES) Organization. This paper presents an application of the joint Penn State University/Technical University of Madrid (UPM) version of the well-known sub-channel code COBRA-TF (Coolant Boiling in Rod Array-Two Fluid), namely, CTF, to the steady state critical power and departure from nucleate boiling (DNB) exercises of the OECD/NRC BFBT and PSBT benchmarks. The goal is two-fold: firstly, to assess these models and to examine their strengths and weaknesses; and secondly, to identify the areas for improvement.

Influencia de las condiciones de ejecución en la resistencia de anclajes en convencional y autocompactante

A través de los años las estructuras de hormigón armado han ido aumentando su cuota de mercado, sustituyendo a las estructuras de fábrica de piedra o ladrillo y restándole participación a las estructuras metálicas. Uno de los primeros problemas que surgieron al ejecutar las estructuras de hormigón armado, era cómo conectar una fase de una estructura de este tipo a una fase posterior o a una modificación posterior. Hasta los años 80-90 las conexiones de una fase de una estructura de hormigón armado, con otra posterior se hacían dejando en la primera fase placas de acero con garrotas embebidas en el hormigón fresco o barras grifadas recubiertas de poliestireno expandido. Una vez endurecido el hormigón se podían conectar nuevas barras, para la siguiente fase mediante soldadura a la placa de la superficie o enderezando las barras grifadas, para embeberlas en el hormigón fresco de la fase siguiente. Estos sistemas requerían conocer la existencia y alcance de la fase posterior antes de hormigonar la fase previa. Además requerían un replanteo muy exacto y complejo de los elementos de conexión. Otro problema existente en las estructuras de hormigón era la adherencia de un hormigón fresco a un hormigón endurecido previamente, ya que la superficie de contacto de ambos hormigones suponía un punto débil, con una adherencia baja. A partir de los años 80, la industria química de la construcción experimentó un gran avance en el desarrollo de productos capaces de generar una buena adherencia sobre el hormigón endurecido. Este avance tecnológico tenía aplicación tanto en la adherencia del hormigón fresco sobre el hormigón endurecido, como en la adherencia de barras post-instaladas en agujeros de hormigón endurecido. Este sistema se denominó “anclajes adherentes de barras de acero en hormigón endurecido”. La forma genérica de ejecutarlos es hacer una perforación cilíndrica en el soporte de hormigón, con una herramienta especifica como un taladro, limpiar la perforación, llenarla del material adherente y finalmente introducir la barra de acero. Los anclajes adherentes se dividen en anclajes cementosos y anclajes químicos, siendo estos últimos los más habituales, fiables, resistentes y fáciles de ejecutar. El uso del anclaje adherente de barras de acero en hormigón endurecido se ha extendido por todo el espectro productivo, siendo muy habitual tanto en construcción de obras de hormigón armado de obra civil y edificación, como en obras industriales, instalaciones o fijación de elementos. La ejecución de un anclaje de una barra de acero en hormigón endurecido depende de numerosas variables, que en su conjunto, o de forma aislada pueden afectar de forma notable a la resistencia del anclaje. Nos referimos a variables de los anclajes, que a menudo no se consideran tales como la dirección de la perforación, la máquina de perforación y el útil de perforación utilizado, la diferencia de diámetros entre el diámetro del taladro y la barra, el tipo de material de anclaje, la limpieza del taladro, la humedad del soporte, la altura del taladro, etc. La utilización en los últimos años de los hormigones Autocompactables, añade una variable adicional, que hasta ahora apenas ha sido estudiada. En línea con lo apuntado, la presente tesis doctoral tiene como objetivo principal el estudio de las condiciones de ejecución en la resistencia de los anclajes en hormigón convencional y autocompactable. Esta investigación se centra principalmente en la evaluación de la influencia de una serie de variables sobre la resistencia de los anclajes, tanto en hormigón convencional como en un hormigón autocompactable. Para este estudio ha sido necesaria la fabricación de dos soportes de hormigón sobre los cuales desarrollar los ensayos. Uno de los bloques se ha fabricado con hormigón convencional y el otro con hormigón autocompactable. En cada pieza de hormigón se han realizado 174 anclajes con barras de acero, variando los parámetros a estudiar, para obtener resultados de todas las variables consideradas. Los ensayos a realizar en ambos bloques son exactamente iguales, para poder comparar la diferencia entre un anclaje en un soporte de hormigón con vibrado convencional (HVC) y un hormigón autocompactante (HAC). De cada tipo de ensayo deseado se harán dos repeticiones en la misma pieza. El ensayo de arrancamiento de las barras se realizara con un gato hidráulico hueco, con un sistema de instrumentación de lectura y registro de datos en tiempo real. El análisis de los resultados, realizado con una potente herramienta estadística, ha permitido determinar y evaluar numéricamente la influencia de los variables consideradas en la resistencia de los anclajes realizados. Así mismo ha permitido diferenciar los resultados obtenidos en los hormigones convencionales y autocompactantes, tanto desde el punto de vista de la resistencia mecánica, como de las deformaciones sufridas en el arrancamiento. Se define la resistencia mecánica de un anclaje, como la fuerza desarrollada en la dirección de la barra, para hacer su arrancamiento del soporte. De la misma forma se considera desplazamiento, a la separación entre un punto fijo de la barra y otro del soporte, en la dirección de la barra. Dichos puntos se determinan cuando se ha terminado el anclaje, en la intersección de la superficie plana del soporte, con la barra. Las conclusiones obtenidas han permitido establecer qué variables afectan a la ejecución de los anclajes y en qué cuantía lo hacen, así como determinar la diferencia entre los anclajes en hormigón vibrado convencional y hormigón autocompactante, con resultados muy interesantes, que permiten valorar la influencia de dichas variables. Dentro de las conclusiones podemos destacar tres grupos, que denominaremos como de alta influencia, baja influencia y sin influencia. En todos los casos hay que hacer el estudio en términos de carga y de desplazamiento. Podemos considerar como de alta influencia, en términos de carga las variables de máquina de perforación y el material de anclaje. En términos de desplazamiento podemos considerar de alta influencia además de la máquina de perforación y el material de anclaje, el diámetro del taladro, así como la limpieza y humedad del soporte. Podemos considerar de baja influencia, en términos de carga las variables de tipo de hormigón, dirección de perforación, limpieza y humedad del soporte. En términos de desplazamiento podemos considerar de baja influencia el tipo de hormigón y la dirección de perforación. Podemos considerar en el apartado de “sin influencia”, en términos de carga las variables de diámetro de perforación y altura del taladro. En términos de desplazamiento podemos considerar como “sin influencia” la variable de altura del taladro. Podemos afirmar que las diferencias entre los valores de carga aumentan de forma muy importante en términos de desplazamiento. ABSTRACT Over the years the concrete structures have been increasing their market share, replacing the masonry structures of stone or brick and subtracting as well the participation of the metallic structures. One of the first problems encountered in the implementing of the reinforced concrete structures was connecting a phase structure of this type at a later stage or a subsequent amendment. Until the 80s and 90s the connections of one phase of a reinforced concrete structure with a subsequent first phase were done by leaving the steel plates embedded in the fresh concrete using hooks or bent bars coated with expanded polystyrene. Once the concrete had hardened new bars could be connected to the next stage by welding them to the surface plate or by straightening the bent bars to embed them in the fresh concrete of the next phase. These systems required a previous knowledge of the existence and scope of the subsequent phase before concreting the previous one. They also required a very precise and complex rethinking of the connecting elements. Another existing problem in the concrete structures was the adhesion of a fresh concrete to a previously hardened concrete, since the contact surface of both concretes leaded to a weak point with low adherence. Since the 80s, the chemicals construction industry experienced a breakthrough in the development of products that generate a good grip on the concrete. This technological advance had its application both in the grip on one hardened fresh concrete and in the adhesion of bar post-installed in holes of hardened concrete. This system was termed as adherent anchors of steel bars in hardened concrete. The generic way of executing this system is by firstly drilling a cylindrical hole in the concrete support using a specific tool such as a drill. Then, cleaning the bore and filling it with bonding material to lastly, introduce the steel bar. These adherent anchors are divided into cement and chemical anchors, the latter being the most common, reliable, durable and easy to run. The use of adhesive anchor of steel bars in hardened concrete has spread across the production spectrum turning itself into a very common solution in both construction of reinforced concrete civil engineering and construction, and industrial works, installations and fixing elements as well. The execution of an anchor of a steel bar in hardened concrete depends on numerous variables which together or as a single solution may significantly affect the strength of the anchor. We are referring to variables of anchors which are often not considered, such as the diameter difference between the rod and the bore, the drilling system, cleansing of the drill, type of anchor material, the moisture of the substrate, the direction of the drill, the drill’s height, etc. During recent years, the emergence of self-compacting concrete adds an additional variable which has hardly been studied so far. According to mentioned this thesis aims to study the main performance conditions in the resistance of conventional and self-compacting concrete anchors. This research is primarily focused on the evaluation of the influence of several variables on the strength of the anchoring, both in conventional concrete and self-compacting concrete. In order to complete this study it has been required the manufacture of two concrete supports on which to develop the tests. One of the blocks has been manufactured with conventional concrete and the other with self-compacting concrete. A total of 174 steel bar anchors have been made in each one of the concrete pieces varying the studied parameters in order to obtain results for all variables considered. The tests to be performed on both blocks are exactly the same in order to compare the difference between an anchor on a stand with vibrated concrete (HVC) and a self-compacting concrete (SCC). Each type of test required two repetitions in the same piece. The pulling test of the bars was made with a hollow jack and with an instrumentation system for reading and recording data in real time. The use of a powerful statistical tool in the analysis of the results allowed to numerically determine and evaluate the influence of the variables considered in the resistance of the anchors made. It has likewise enabled to differentiate the results obtained in the self-compacting and conventional concretes, from both the outlook of the mechanical strength and the deformations undergone by uprooting. The mechanical strength of an anchor is defined as the strength undergone in a direction of the bar to uproot it from the support. Likewise, the movement is defined as the separation between a fixed point of the bar and a fixed point from the support considering the direction of the bar. These points are only determined once the anchor is finished, with the bar, at the intersection in the flat surface of the support. The conclusions obtained have established which variables affect the execution of the anchors and in what quantity. They have also permitted to determine the difference between the anchors in vibrated concrete and selfcompacting concrete with very interesting results that also allow to assess the influence of these mentioned variables. Three groups are highlighted among the conclusions called high influence, low influence and no influence. In every case is necessary to perform the study in terms of loading and movement. In terms of loading, there are considered as high influence two variables: drilling machinery and anchorage material. In terms of movement, there are considered as high influence the drilling diameter and the cleaning and moisture of the support, besides the drilling machinery and the anchorage material. Variables such as type of concrete, drilling direction and cleaning and moisture of the support are considered of low influence in terms of load. In terms of movement, the type of concrete and the direction of the drilling are considered variables of low influence. Within the no influence section in terms of loading, there are included the diameter of the drilling and the height of the drill. In terms of loading, the height of the drill is considered as a no influence variable. We can affirm that the differences among the loading values increase significantly in terms of movement.

Good and bad practices in pv plants

The PVCROPS project (PhotoVolta ic Cost r€duction, Reliability, Operational performance, Prediction and Simulation), cofinanced by European Commission in the frame of Seventh Framework Programme, has compiled in the “Good and bad practices: Manual to improve the quality and reduce the cost of PV systems” a collection of good and bad practices in actual PV plants . All the situations it collects represent the state-of-the-art of existing PV installations all around Europe. They show how the different parts of an installation can be implem ented properly or not. The aim of this manual is to represent a reference text which can help any PV actor (installers, electricians, maintenance operators, owners, etc.) not only to check and improve an already existing installation but will also, and mainly, avoid the previously known bad practices for the construction of a new PV installation. Thus, solving a priori the known errors, new PV installations will be more reliable, efficient and cost-effective and can recover the initial investment in a shorter time. The manual is going to be free available in the PVCROPS website in several languages.

LED bulbs technical specification and testing procedure for solar home systems

The definition of technical specifications and the corresponding laboratory procedures are necessary steps in order to assure the quality of the devices prior to be installed in Solar Home Systems (SHS). To clarify and unify criteria a European project supported the development of the Universal Technical Standard for Solar Home Systems (UTSfSHS). Its principles were to generate simple and affordable technical requirements to be optimized in order to facilitate the implementation of tests with basic and simple laboratory tools even on the same SHS electrification program countries. These requirements cover the main aspects of this type of installations and its lighting chapter was developed based on the most used technology at that time: fluorescent tubes and CFLs. However, with the consolidation of the new LED solid state lighting devices, particular attention is being given to this matter and new procedures are required. In this work we develop a complete set of technical specifications and test procedures that have been designed within the frame of the UTSfSHS, based on an intense review of the scientific and technical publications related to LED lighting and their practical application. They apply to lamp reliability, performance and safety under normal, extreme and abnormal operating conditions as a simple but complete quality meter tool for any LED bulb.

Ventilation and FFFS fire tests for “Calle 30” road tunnels

Between 2003 and 2007 an urban network or road tunnels with a total constructed tubes length of 45 km was built in the city of Madrid. This amazing engineering work, known as "Calle 30 Project" counted with different kinds of tunnel typologies and ventilation systems. Due to the length of the tunnels and the impact of the work itself, the tunnels were endowed with a great variety of installations to provide the maximum levels of safety both for users and the infrastructure includieng, in some parts of the tunnel, fixed fire fighting system based on water mist. Whithin this framework a large-scale programme of fire tests was planned to study different aspects related to fire safety in the tunnels including the phenomena of the interaction between ventilation and extinguishing system. In addition, these large scale fire tests allowed fire brigades of the city of Madrid an opportunity to define operational procedures for specific fire fighting in tunnels and evaluate the possibilities of fixed fire fighting systems. The tests were carried out in the Center of Experimentation "San pedro of Anes" which includes a 600 m tunnel with a removable false ceiling for reproducing different ceiling heights and ventilation conditions (transverse and longitudinal ones). Interesting conclusions on the interaction of ventilation and water mist systems were obtained but also on other aspects including performance of water mist system in terms of reduction of gas temperatures or visibility conditions. This paper presents a description of the test's programme carried out and some previous results obtained.

Large Scale Fire Tests for the “Calle 30 Project"

Between 2003 and 2007 an urban network of road tunnels with a total constructed tubes length of 45 km was built in the city of Madrid. This amazing engineering work, known as “Calle30 Project” counted with different kinds of tunnel typologies and ventilation systems. Due to the length of the tunnels and the impact of the work itself, the tunnels were endowed with a great variety of installations to provide the maximum levels of safety both for users and the infrastructure including,in some parts of the tunnel, fixed fire fighting system based on water mist. Within this framework a large-scale campaign of fire tests were planned to study different aspects related to fire safety in the tunnels including the phenomena of the interaction between ventilation and extinction system. In addition, this large scale fire tests allowed fire brigades of the city of Madrid an opportunity to define operational procedures for specific fire fighting in tunnels and evaluate the possibilities of fixed fire fighting systems. The tests were carried out in the Center of Experimentation "San Pedro of Anes" which counts with a 600 m tunnel with a removable false ceiling for reproducing different ceiling heights and ventilation conditions (transverse and longitudinal ones). Interesting conclusions on the interaction of ventilation and water mist systems were obtained but also on other aspects including performance of water mist system in terms of reduction of gas temperatures or visibility conditions. This paper presents a description of the test’s campaign carried out and some previous results obtained.

Modelización de una central térmica supercrítica de 700 MW con captura de CO₂

El objetivo de este proyecto es realizar la simulación de una central térmica supercrítica de 700 MW con captura de CO₂ para producir electricidad y verterla a la red. El proyecto describe los equipos e instalaciones de la central y define los balances técnicos de la misma, probando que es viable técnicamente la incorporación de una planta de captura de CO₂ a una central térmica, a pesar del bajo rendimiento de la central. Además incluye el estudio económico que indica la viabilidad económica del proyecto, aunque con una rentabilidad baja. Este proyecto mira hacia el futuro debido a la necesidad de reducir las emisiones contaminantes, ya de casi la misma importancia que generar electricidad, y demuestra que es posible generar una energía limpia en centrales de carbón. ABSTRACT The purpose of this project is to carry out the simulation of a 700 MW supercritical coal thermal power plant with CO₂ capture to produce electricity and send it to the grid. The project describes the equipment, the installations and defines technical balances of the power plant. It shows that a CO₂ capture plant in a coal power plant is technically possible, in spite of the low power plant efficiency. In addition, it includes the economic analysis that shows the economic viability of the project, with a low profitability. This project looks into the future due to the need of reducing the pollutant emissions, which are almost as important as the generation of electricity, and demonstrates that a green energy in coal power plants is possible.