Operational Modal Analysis on laminated glass beams

Laminated glass is a sandwich element consisting of two or more glass sheets, with one or more interlayers of polyvinyl butyral (PVB). The dynamic response of laminated glass beams and plates can be predicted using analytical or numerical models in which the glass and the PVB are usually modelled as linear-elastic and linear viscoelastic materials, respectively. In this work the dynamic behavior of laminated glass beams are predicted using a finite element model and the analytical model of Ross-Kerwin-Ungar. The numerical and analytical results are compared with those obtained by operational modal analysis performed at different temperatures.

Amplificador de señal analógico basado en conceptos biomiméticos. Desarrollo de modelos computacionales y validación experimental

La presente tesis doctoral estudia las características de un transductor acústico bioinspirado en la estructura del maxilar inferior de un Zifio de Couvier (Ziphius cavirostris). El mecanismo de funcionamiento del sensor se basa en las características de un sistema acoplado formado por los distintos componentes acústicos identificados en el maxilar. Para analizar las características del sensor se propone un modelo simplificado 2D que consta de una cavidad cerrada con forma de bocina acoplada a una lengüeta. Una parte de la lengüeta se encuentra dentro de la cavidad y otra en el exterior. Dicha lengüeta detecta los cambios de presión acústica y las vibraciones generadas por el sonido y las transmite con ondas de flexión al interior de la cavidad. La excitación prolongada sobre la placa puede provocar la activación de los modos propios del sistema acoplado. Dichos modos se caracterizan porque presentan un máximo de presión en el cono de la bocina la cual a su vez actúa como un amplificador acústico. Mediante el Método de los elementos Finitos se analizan las características acústicas del sensor y se construye un prototipo experimental para validar los resultados evaluados en el modelo numérico. Se propone una metodología numérica que permite desarrollar y validar un elemento tetraédrico para caracterizar el comportamiento isotrópico de los medios porosos. La metodología permite construir elementos de línea y bidimensionales. A partir de esta metodología se desarrolla un elemento plano ortotrópico. Se realiza un modelo de la cavidad en el que una de las paredes de la bocina está constituida por material poroso y se une la parte exterior de la lengüeta a dicho material para que constituya una viga sobre un apoyo elástico. Se calcula la respuesta modal y se discuten los efectos del material poroso en la eficiencia del transductor y las posibles mejoras a introducir en el mismo. SUMMARY This Thesis studies the characteristics of an acoustic transducer bioinspired by the structure of the lower maxilla of an odontoceto. In this case a Cuvier’s beaked whale (Ziphius cavirostris). The transducer working mechanism is based in a coupled system, with components identified in the maxilla. To analyze the transducer a simplified 2D model composed by a horn shaped closed cavity is modeled. The cavity is coupled with a flat belt. The belt has one part inside the cavity and the other part outside of it. The belt traverses the cavity wall and it is in charge to pick the vibrations from outside and introduce it inside the cavity. The transmission is obtained through the belt bending. A sustained external load with the right frequency contents will allow the system to reach a stationary pressure intensity distribution inside the cavity. Frequencies with modal shapes that show an important intensity increase at the horn tip are of special interest because of the signal amplification. A finite element model is constructed to study the transducer coupled modes and a prototype is constructed to validate the numerical results. A numerical methodology to construct and validate a tetrahedral finite element for isotropic porous materials is presented. The methodology allows constructing linear and 2D elements. It is extended to model orthotropic porous materials behavior. At the end, one of the horn walls is made of an orthotropic material and the external belt is glued to it in order to configure a belt over an elastic foundation. Modal response is evaluated and the porous material effects in the transducer efficiency and further improvements are discussed.

Estudio numérico y experimental del efecto de tamaño en modo mixto de los paneles de yeso laminado y lana de roca

Los paneles sándwich de yeso laminado y lana de roca presentan una abundante patología de fisuración debida a flechas excesivas de forjados. Existe, por tanto, la necesidad de avanzar en la simulación y predicción de comportamiento bajo solicitaciones de tracción y cortante de ese tipo de paneles, a pesar de que en las aplicaciones habituales no tienen responsabilidad estructural. El comportamiento de este material puede ser considerado cuasi-frágil, y en base a ello en este trabajo ha sido estudiado haciendo uso de modelos de fisura cohesiva, cuya aplicación a otros materiales cuasifrágiles, como el hormigón, ha aportado resultados muy satisfactorios. En esta comunicación se presenta el trabajo realizado para estudiar el efecto del tamaño del elemento de yeso laminado y lana de roca en su comportamiento mecánico-resistente. Para ello se diseñó una campaña de ensayos en modo mixto sobre probetas de diferente tamaño. Se han realizado ensayos de flexión en tres puntos en modo mixto de unas probetas entalladas, geométricamente similares y de diferente tamaño, obteniéndose las curvas carga-desplazamiento y cargaabertura de la boca de la entalla. Para simular numéricamente el comportamiento en fractura del panel en modo mixto se ha utilizado un modelo de elementos finitos con fisura embebida basado en la fisura cohesiva en el que se introducen como entrada los parámetros obtenidos a partir de la experimentación de trabajos anteriores, obteniéndose un buen ajuste. En función de estos resultados se analiza el efecto del tamaño en los paneles. Sandwich panels of laminated gypsum and rockwool have an abundant pathology of cracking due to excessive slabs deflection. Therefore, it is necessary to progress in the simulation and prediction of behaviour under tensile and shear load of such panels, although in typical applications have no structural responsability. The behaviour of this material may be considered quasi-brittle and, based on this idea, in this work has been studied using a cohesive crack model that has been applied to other quasi-brittle materials, such as concrete, and has provided very satisfactory results. This communication presents the work carried out to study the size effect of the specimen of plasterboard and rockwool in its mechanical and resistant behaviour. The authors designed an experimental campaign under mixed mode composed by testing specimens of different sizes. Assymetrical three-point bending tests have been performed on notched specimens, geometrically similar and of different size, to obtain load-displacement and load-crack moutn opening displacement curves. To numerically simulate the mixed-mode fracture behaviour of the panels we have used a finite element model with embedded crack, based on the cohesive crack model, using as input the experimental parameters obtained in previous work, obtaining a good adjustment. Based on these results we analyze the size effect of the panels

Computational Methods for Identification of Vibrating Structures

System identification deals with the problem of building mathematical models of dynamical systems based on observed data from the system" [1]. In the context of civil engineering, the system refers to a large scale structure such as a building, bridge, or an offshore structure, and identification mostly involves the determination of modal parameters (the natural frequencies, damping ratios, and mode shapes). This paper presents some modal identification results obtained using a state-of-the-art time domain system identification method (data-driven stochastic subspace algorithms [2]) applied to the output-only data measured in a steel arch bridge. First, a three dimensional finite element model was developed for the numerical analysis of the structure using ANSYS. Modal analysis was carried out and modal parameters were extracted in the frequency range of interest, 0-10 Hz. The results obtained from the finite element modal analysis were used to determine the location of the sensors. After that, ambient vibration tests were conducted during April 23-24, 2009. The response of the structure was measured using eight accelerometers. Two stations of three sensors were formed (triaxial stations). These sensors were held stationary for reference during the test. The two remaining sensors were placed at the different measurement points along the bridge deck, in which only vertical and transversal measurements were conducted (biaxial stations). Point estimate and interval estimate have been carried out in the state space model using these ambient vibration measurements. In the case of parametric models (like state space), the dynamic behaviour of a system is described using mathematical models. Then, mathematical relationships can be established between modal parameters and estimated point parameters (thus, it is common to use experimental modal analysis as a synonym for system identification). Stable modal parameters are found using a stabilization diagram. Furthermore, this paper proposes a method for assessing the precision of estimates of the parameters of state-space models (confidence interval). This approach employs the nonparametric bootstrap procedure [3] and is applied to subspace parameter estimation algorithm. Using bootstrap results, a plot similar to a stabilization diagram is developed. These graphics differentiate system modes from spurious noise modes for a given order system. Additionally, using the modal assurance criterion, the experimental modes obtained have been compared with those evaluated from a finite element analysis. A quite good agreement between numerical and experimental results is observed.

Estudio numérico y experimental del efecto de tamaño en modo mixto de los paneles de yeso laminado y lana de roca

Los paneles sándwich de yeso laminado y lana de roca presentan una abundante patología de fisuración debida a flechas excesivas de forjados. Existe, por tanto, la necesidad de avanzar en la simulación y predicción de comportamiento bajo solicitaciones de tracción y cortante de ese tipo de paneles, a pesar de que en las aplicaciones habituales no tienen responsabilidad estructural. El comportamiento de este material puede ser considerado cuasi-frágil, y en base a ello en este trabajo ha sido estudiado haciendo uso de modelos de fisura cohesiva, cuya aplicación a otros materiales cuasifrágiles, como el hormigón, ha aportado resultados muy satisfactorios. En esta comunicación se presenta el trabajo realizado para estudiar el efecto del tamaño del elemento de yeso laminado y lana de roca en su comportamiento mecánico-resistente. Para ello se diseñó una campaña de ensayos en modo mixto sobre probetas de diferente tamaño. Se han realizado ensayos de flexión en tres puntos en modo mixto de unas probetas entalladas, geométricamente similares y de diferente tamaño, obteniéndose las curvas carga-desplazamiento y cargaabertura de la boca de la entalla. Para simular numéricamente el comportamiento en fractura del panel en modo mixto se ha utilizado un modelo de elementos finitos con fisura embebida basado en la fisura cohesiva en el que se introducen como entrada los parámetros obtenidos a partir de la experimentación de trabajos anteriores, obteniéndose un buen ajuste. En función de estos resultados se analiza el efecto del tamaño en los paneles. Sandwich panels of laminated gypsum and rockwool have an abundant pathology of cracking due to excessive slabs deflection. Therefore, it is necessary to progress in the simulation and prediction of behaviour under tensile and shear load of such panels, although in typical applications have no structural responsability. The behaviour of this material may be considered quasi-brittle and, based on this idea, in this work has been studied using a cohesive crack model that has been applied to other quasi-brittle materials, such as concrete, and has provided very satisfactory results. This communication presents the work carried out to study the size effect of the specimen of plasterboard and rockwool in its mechanical and resistant behaviour. The authors designed an experimental campaign under mixed mode composed by testing specimens of different sizes. Assymetrical three-point bending tests have been performed on notched specimens, geometrically similar and of different size, to obtain load-displacement and load-crack moutn opening displacement curves. To numerically simulate the mixed-mode fracture behaviour of the panels we have used a finite element model with embedded crack, based on the cohesive crack model, using as input the experimental parameters obtained in previous work, obtaining a good adjustment. Based on these results we analyze the size effect of the panels.

Study of the Edge and Surface Cracks Influence in the Mechanical Strength of Silicon Wafers

The objective of the present study is the estimation of the depth to which the wire sawing process causes damage to the wafer surfaces. Previous analyses were carried out by means of the four line bending test. The characteristic of this test implied that the failure could be due to surface cracks located in the central zone of the wafer or near the edges. In order to evaluate the influence of the edge or surface cracks a new study has been carried out using the ball/ring on ring test. Description and results of the tests are presented. The preliminary analysis of the failure stress using analytical methods confirms the expected results. A Finite Element model developed to get more information of the test results is also presented.

Análisis experimental y por el método de los elementos finitos del estado de tensiones en uniones carpinteras de empalme de llave

In this research, the halved and tabled traditional timber scarf joint is analyzed. This joint consists in two end joint pieces usually subjected to tension. Initially, the study is discussed from an experimental point of view. In this way, 3 critical cross-sections are established (section of the notch, section of the horizontal plane and reduced section) and mechanical tests are performed to achieve the failure on each of critical sections by changing the geometry of the joint. The study is completed by developing a finite element model which allows verify experimental results and extend the analysis to other geometries. This model has to simulate the real behavior of the material which is being studied, so mechanical tests are performed to obtain the elastic constants and the coefficients of friction of the material. In the reduced section, an abrupt decrease of the effective cross-section takes place, and this effect is also experimentally analyzed. These tests indicate that a crack is initiated before the bending-tension failure occurs in the reduced section. The test material consists of wood of Pinus sylvestris L. coming from the “Valsaín´s Sawmill” (Segovia) with “premium quality” according to the nonstructural wood visual classification of sawmill. It is observed that initiation of a crack, in the mortise (bottom of reduced section), and shear stress concentration, at the initial part of the heel (beginning of horizontal plane), completely determine the mechanical behaviour of the joint, resulting in 3 failure modes: local compression failure in the section of the notch, shear failure in the horizontal plane, and failure of stresses concentration, mainly perpendicular to the grain tension, at the bottom of reduced section. The geometric optimization is obtained for halved and tabled traditional scarf joint, when the joint has made with similar properties of wood than tested specimens, for any height and width of the cross-section. It is considered the failure due to the initiation of a crack in reduced section, by applying a correction coefficient into the usual equation used to design the members subjected to both tension and bending. Therefore, it is possible to obtain, analytically, the design conditions to be met of the 3 critical cross-sections. According to the theoretical optimization, the tension strength of complete cross-section is reduced until 14%, when using this type of joint. The experimental optimization indicates even a greater reduction, until 6%. En el presente trabajo de investigación se analiza el comportamiento mecánico de las uniones tradicionales de empalme de llave, que consisten en dos piezas unidas por sus testas transmitiéndose entre ellas principalmente un esfuerzo de tracción. Inicialmente, el estudio se aborda desde un punto de vista experimental. De este modo, se establecen las 3 secciones críticas o de estudio (sección del encaje, sección rasante del cogote y sección reducida) y se realizan ensayos mecánicos, variando la geometría de la unión, para alcanzar la rotura en cada una de ellas. Se completa el estudio mediante la elaboración de un modelo por elementos finitos que permite verificar los resultados experimentales y ampliar el análisis a otras geometrías. Este modelo debe simular el comportamiento real del material objeto de estudio, por lo que se realizan ensayos para obtener las constantes elásticas y los coeficientes de rozamiento del mismo. También se analiza, experimentalmente, el efecto entalladura que reduce bruscamente la sección completa del tirante, estableciendo que el fallo por flexotracción en la sección reducida de la pieza, no llega a producirse por el inicio previo de una grieta. El material de ensayo consiste en madera de Pinus sylvestris L. (pino silvestre) procedente del Aserradero de Valsaín (Segovia) y de calidad “Extra” o “Primera” según la clasificación visual no estructural del aserradero. Se observa que el inicio de una grieta en la mortaja del rediente y la concentración de tensiones tangenciales en la parte inicial del cogote, determinan completamente el comportamiento mecánico de la unión, dando lugar a 3 modos distintos de rotura: fallo por compresión en la sección del encaje, fallo por cortante en la sección rasante y fallo por concentración de tensiones, principalmente tracciones perpendiculares, en el rebaje de la sección reducida. Se consigue optimizar geométricamente cualquier empalme de llave confeccionado con madera de características similares a la ensayada, para cualquier valor de la altura y de la anchura de la sección. Se considera el agotamiento en la sección reducida causado por el inicio de grieta, mediante la aplicación de un coeficiente corrector en la expresión habitual de agotamiento por flexotracción, en consecuencia, finalmente es posible obtener, de modo analítico, un valor del índice de agotamiento en cada una de las 3 secciones de estudio. La optimización teórica del empalme de llave indica que la capacidad resistente del tirante bruto se reduce al 14%, cuando se coloca este tipo de unión tradicional. Experimentalmente se obtiene, que, para la sección ensayada, la capacidad resistente del tirante bruto se reduce todavía más, llegando al 6%.

Seismic performance case study of bridge pile cap foundation

The purpose of this report is to build a model that represents, as best as possible, the seismic behavior of a pile cap bridge foundation by a nonlinear static (analysis) procedure. It will consist of a reproduction of a specimen already built in the laboratory. This model will carry out a pseudo static lateral and horizontal pushover test that will be applied onto the pile cap until the failure of the structure, the formation of a plastic hinge in the piles due to the horizontal deformation, occurs. The pushover test consists of increasing the horizontal load over the pile cap until the horizontal displacement wanted at the height of the pile cap is reached. The output of this model will be a Skeleton curve that will plot the lateral load (kN) over the displacement (m), so that the maximum movement the pile cap foundation can reach before its failure can be calculated. This failure will be achieved when the load at that specific shift is equal to 85% of the maximum. The pile cap foundation finite element model was based on pile cap built for a laboratory experiment already carried out by the Master student Deming Zhang at Tongji University. Two different pile caps were tested with a difference in height above the ground level. While one has 0:3m, the other rises 0:8m above the ground level. The computer model was calibrated using the experimental results. The pile cap foundation will be programmed in a finite element environment called OpenSees (Open System for Earthquake Engineering Simulation [28]). This environment is a free software developed by Berkeley University specialized, as it name says, in the study of earthquakes and its effects on structures. This specialization is the main reason why it is being used for building this model as it makes it possible to build any finite element model, and perform several analysis in order to get the results wanted. The development of OpenSees is sponsored by the Pacific Earthquake Engineering Research Center through the National Science Foundation engineering and education centers program. OpenSees uses Tcl language to program it, which is a language similar to C++.

Modelling of chloride penetration into non-saturated concrete: Case study application for real marine off shore structures

The aim of this paper is to explain the chloride concentration profiles obtained experimentally from control samples of an offshore platform after 25 years of service life. The platform is located 12 km off the coast of the Brazilian province Rio Grande do Norte, in the north-east of Brazil. The samples were extracted at different orientations and heights above mean sea level. A simple model based on Fick’s second law is considered and compared with a finite element model which takes into account transport of chloride ions by diffusion and convection. Results show that convective flows significantly affect the studied chloride penetrations. The convection velocity is obtained by fitting the finite element solution to the experimental data and seems to be directly proportional to the height above mean sea level and also seems to depend on the orientation of the face of the platform. This work shows that considering solely diffusion as transport mechanism does not allow a good prediction of the chloride profiles. Accounting for capillary suction due to moisture gradients permits a better interpretation of the material’s behaviour.

Moment transfer and influence of transverse beams in interior waffle flat plate-column connections under lateral loading

This paper addresses two aspects of the behavior of interior reinforced concrete waffle flat plate?column connections under lateral loads: the share of the unbalanced moment between flexure and excentric shear, and the effect of the transverse beams. A non-linear finite element model (benchmark model) was developed and calibrated with the results of quasi-static cyclic tests conducted on a 3/5 scale specimen. First, from this numerical model, the portion cv of the unbalanced moment transferred by the excentricity of shear about the centroid of the critical sections defined by Eurocode 2 (EC-2) and by ACI 318-11 was calculated and compared with the share-out prescribed by these codes. It is found that while the critical section of EC-2 is consistent with the cv provided by this code, in the case of ACI 318-11, the value assigned to cv is far below (about 50% smaller) the actual one obtained with the numerical simulations. Second, from the benchmark model, seven additional models were developed by varying the depth D of the transverse beam over the thickness h of the plate. It was found that the ductility of the connection and the effective width of the plate can respectively be increased up to 50% and 10% by raising D/h to 2 and 1.5.

Sensibilidad a las entallas del acero inoxidable dúplex fuertemente trefilado

En el presente trabajo se estudia la sensibilidad a las entallas suaves de alambres de acero inoxidable dúplex fuertemente trefilado. Las entallas consideradas son reducciones de la sección transversal del alambre no simétricas respecto al eje de revolución. Tras constatar experimentalmente que los alambres con este tipo de daño fallan por agotamiento plástico, se ha determinado numéricamente la carga de agotamiento plástico en función de la profundidad de entalla empleando un mode-lo computacional de elementos finitos. Los resultados numéricos indican que la mayor deformabilidad del alambre debida a la entalla actúa en favor de su tolerancia al daño y permite que ésta alcance el límite superior dado por la carga de agotamiento a tracción simple del ligamento resistente.This research deals with the sensitivity to blunt notches of highly cold-drawn wires made of dúplex stainless steel. The analyzed notches are actually reductions of the wire cross section, asymmetrically mechanized with respect to the longitudinal wire axis. Once experimentally verified that the notched wires fail by plástic collapse, the failure load was found as a function of notch depth by means of a finite element model. The numerical results show that the higher compliance of the wires provided by the notch increases their damage tolerance up to the upper bound given by the tensile plástic failure load of the notch ligament.

Continuum models of the mechanical behavior of rolled and die-cast magnesium alloys

En los últimos años ha habido una fuerte tendencia a disminuir las emisiones de CO2 y su negativo impacto medioambiental. En la industria del transporte, reducir el peso de los vehículos aparece como la mejor opción para alcanzar este objetivo. Las aleaciones de Mg constituyen un material con gran potencial para el ahorro de peso. Durante la última década se han realizado muchos esfuerzos encaminados a entender los mecanismos de deformación que gobiernan la plasticidad de estos materiales y así, las aleaciones de Mg de colada inyectadas a alta presión y forjadas son todavía objeto de intensas campañas de investigación. Es ahora necesario desarrollar modelos que contemplen la complejidad inherente de los procesos de deformación de éstos. Esta tesis doctoral constituye un intento de entender mejor la relación entre la microestructura y el comportamiento mecánico de aleaciones de Mg, y dará como resultado modelos de policristales capaces de predecir propiedades macro- y microscópicas. La deformación plástica de las aleaciones de Mg está gobernada por una combinación de mecanismos de deformación característicos de la estructura cristalina hexagonal, que incluye el deslizamiento cristalográfico en planos basales, prismáticos y piramidales, así como el maclado. Las aleaciones de Mg de forja presentan texturas fuertes y por tanto los mecanismos de deformación activos dependen de la orientación de la carga aplicada. En este trabajo se ha desarrollado un modelo de plasticidad cristalina por elementos finitos con el objetivo de entender el comportamiento macro- y micromecánico de la aleación de Mg laminada AZ31 (Mg-3wt.%Al-1wt.%Zn). Este modelo, que incorpora el maclado y tiene en cuenta el endurecimiento por deformación debido a las interacciones dislocación-dislocación, dislocación-macla y macla-macla, predice exitosamente las actividades de los distintos mecanismos de deformación y la evolución de la textura con la deformación. Además, se ha llevado a cabo un estudio que combina difracción de electrones retrodispersados en tres dimensiones y modelización para investigar el efecto de los límites de grano en la propagación del maclado en el mismo material. Ambos, experimentos y simulaciones, confirman que el ángulo de desorientación tiene una influencia decisiva en la propagación del maclado. Se ha observado que los efectos no-Schmid, esto es, eventos de deformación plástica que no cumplen la ley de Schmid con respecto a la carga aplicada, no tienen lugar en la vecindad de los límites de baja desorientación y se hacen más frecuentes a medida que la desorientación aumenta. Esta investigación también prueba que la morfología de las maclas está altamente influenciada por su factor de Schmid. Es conocido que los procesos de colada suelen dar lugar a la formación de microestructuras con una microporosidad elevada, lo cuál afecta negativamente a sus propiedades mecánicas. La aplicación de presión hidrostática después de la colada puede reducir la porosidad y mejorar las propiedades aunque es poco conocido su efecto en el tamaño y morfología de los poros. En este trabajo se ha utilizado un enfoque mixto experimentalcomputacional, basado en tomografía de rayos X, análisis de imagen y análisis por elementos finitos, para la determinación de la distribución tridimensional (3D) de la porosidad y de la evolución de ésta con la presión hidrostática en la aleación de Mg AZ91 (Mg- 9wt.%Al-1wt.%Zn) colada por inyección a alta presión. La distribución real de los poros en 3D obtenida por tomografía se utilizó como input para las simulaciones por elementos finitos. Los resultados revelan que la aplicación de presión tiene una influencia significativa tanto en el cambio de volumen como en el cambio de forma de los poros que han sido cuantificados con precisión. Se ha observado que la reducción del tamaño de éstos está íntimamente ligada con su volumen inicial. En conclusión, el modelo de plasticidad cristalina propuesto en este trabajo describe con éxito los mecanismos intrínsecos de la deformación de las aleaciones de Mg a escalas meso- y microscópica. Más especificamente, es capaz de capturar las activadades del deslizamiento cristalográfico y maclado, sus interacciones, así como los efectos en la porosidad derivados de los procesos de colada. ---ABSTRACT--- The last few years have seen a growing effort to reduce CO2 emissions and their negative environmental impact. In the transport industry more specifically, vehicle weight reduction appears as the most straightforward option to achieve this objective. To this end, Mg alloys constitute a significant weight saving material alternative. Many efforts have been devoted over the last decade to understand the main mechanisms governing the plasticity of these materials and, despite being already widely used, high pressure die-casting and wrought Mg alloys are still the subject of intense research campaigns. Developing models that can contemplate the complexity inherent to the deformation of Mg alloys is now timely. This PhD thesis constitutes an attempt to better understand the relationship between the microstructure and the mechanical behavior of Mg alloys, as it will result in the design of polycrystalline models that successfully predict macro- and microscopic properties. Plastic deformation of Mg alloys is driven by a combination of deformation mechanisms specific to their hexagonal crystal structure, namely, basal, prismatic and pyramidal dislocation slip as well as twinning. Wrought Mg alloys present strong textures and thus specific deformation mechanisms are preferentially activated depending on the orientation of the applied load. In this work a crystal plasticity finite element model has been developed in order to understand the macro- and micromechanical behavior of a rolled Mg AZ31 alloy (Mg-3wt.%Al-1wt.%Zn). The model includes twinning and accounts for slip-slip, slip-twin and twin-twin hardening interactions. Upon calibration and validation against experiments, the model successfully predicts the activity of the various deformation mechanisms and the evolution of the texture at different deformation stages. Furthermore, a combined three-dimensional electron backscatter diffraction and modeling approach has been adopted to investigate the effect of grain boundaries on twin propagation in the same material. Both experiments and simulations confirm that the misorientation angle has a critical influence on twin propagation. Non-Schmid effects, i.e. plastic deformation events that do not comply with the Schmid law with respect to the applied stress, are absent in the vicinity of low misorientation boundaries and become more abundant as misorientation angle increases. This research also proves that twin morphology is highly influenced by the Schmid factor. Finally, casting processes usually lead to the formation of significant amounts of gas and shrinkage microporosity, which adversely affect the mechanical properties. The application of hydrostatic pressure after casting can reduce the porosity and improve the properties but little is known about the effects on the casting’s pores size and morphology. In this work, an experimental-computational approach based on X-ray computed tomography, image analysis and finite element analysis is utilized for the determination of the 3D porosity distribution and its evolution with hydrostatic pressure in a high pressure diecast Mg AZ91 alloy (Mg-9wt.%Al-1wt.%Zn). The real 3D pore distribution obtained by tomography is used as input for the finite element simulations using an isotropic hardening law. The model is calibrated and validated against experimental stress-strain curves. The results reveal that the pressure treatment has a significant influence both on the volume and shape changes of individuals pores, which have been precisely quantified, and which are found to be related to the initial pore volume. In conclusion, the crystal plasticity model proposed in this work successfully describes the intrinsic deformation mechanisms of Mg alloys both at the mesoscale and the microscale. More specifically, it can capture slip and twin activities, their interactions, as well as the potential porosity effects arising from casting processes.

A review of load models for the prediction of footfall-induced vibration in structures

Crowd induced dynamic loading in large structures, such as gymnasiums or stadium, is usually modelled as a series of harmonic loads which are defined in terms of their Fourier coefficients. Different values of these coefficients that were obtained from full scale measurements can be found in codes. Recently, an alternative has been proposed, based on random generation of load time histories that take into account phase lag among individuals inside the crowd. This paper presents the testing done on a structure designed to be a gymnasium. Two series of dynamic test were performed on the gym slab. For the first test an electrodynamic shaker was placed at several locations and during the second one people located inside a marked area bounced and jumped guided by different metronome rates. A finite element model (FEM) is presented and a comparison of numerically predicted and experimentally observed vibration modes and frequencies has been used to assess its validity. The second group of measurements will be compared with predictions made using the FEM model and three alternatives for crowd induced load modelling.

Effects of traffic loads on reinforced concrete railroad culverts

In the context of the present conference paper culverts are defined as an opening or conduit passing through an embankment usually for the purpose of conveying water or providing safe pedestrian and animal crossings under rail infrastructure. The clear opening of culverts may reach values of up to 12m however, values around 3m are encountered much more frequently. Depending on the topography, the number of culverts is about 10 times that of bridges. In spite of this, their dynamic behavior has received far less attention than that of bridges. The fundamental frequency of culverts is considerably higher than that of bridges even in the case of short span bridges. As the operational speed of modern high-speed passenger rail systems rises, higher frequencies are excited and thus more energy is encountered in frequency bands where the fundamental frequency of box culverts is located. Many research efforts have been spent on the subject of ballast instability due to bridge resonance, since it was first observed when high-speed trains were introduced to the Paris/Lyon rail line. To prevent this phenomenon from occurring, design codes establish a limit value for the vertical deck acceleration. Obviously one needs some sort of numerical model in order to estimate this acceleration level and at that point things get quite complicated. Not only acceleration but also displacement values are of interest e.g. to estimate the impact factor. According to design manuals the structural design should consider the depth of cover, trench width and condition, bedding type, backfill material, and compaction. The same applies to the numerical model however, the question is: What type of model is appropriate for this job? A 3D model including the embankment and an important part of the soil underneath the culvert is computationally very expensive and hard to justify taking into account the associated costs. Consequently, there is a clear need for simplified models and design rules in order to achieve reasonable costs. This paper will describe the results obtained from a 2D finite element model which has been calibrated by means of a 3D model and experimental data obtained at culverts that belong to the high-speed railway line that links the two towns of Segovia and Valladolid in Spain

Modifications in the Dynamic Properties of a Structure due to Human Actions

The interest for modelling of human actions acting on structures has been recurrent since the first accidents on suspension bridges in the nineteenth century such as Broughton (1831) in the U.K. or Angers (1850) in France. Stadiums, gymnasiums are other types of structure where human induced vibration is very important. In these structures a particular phenomenon appears such as the interaction personstructure (lock-in), the person-person synchronization, and the influence of the mass and damping of the people in the structural behaviour. This paper focuses on the latter topic. In order to evaluate these property modifications several tests have been carried out on a stand-alone building. For the test an electro-dynamic shaker was installed at a fixed point of the gym slab and different groups of people were located around the shaker. The dynamic characteristics of the structure without people inside have been calculated by two methods: using a three-dimensional finite element model of the building and by operational modal analysis. These calculated experimental and numerical values are the reference values used to evaluate the modifications in the dynamic properties of the structure.