Fossil vs. non-fossil sources of fine carbonaceous aerosols in four Chinese cities during the extreme winter haze episode of 2013

During winter 2013, extremely high concentrations (i.e., 4–20 times higher than the World Health Organization guideline) of PM2.5 (particulate matter with an aerodynamic diameter < 2.5 μm) mass concentrations (24 h samples) were found in four major cities in China including Xi'an, Beijing, Shanghai and Guangzhou. Statistical analysis of a combined data set from elemental carbon (EC), organic carbon (OC), 14C and biomass-burning marker measurements using Latin hypercube sampling allowed a quantitative source apportionment of carbonaceous aerosols. Based on 14C measurements of EC fractions (six samples each city), we found that fossil emissions from coal combustion and vehicle exhaust dominated EC with a mean contribution of 75 ± 8% across all sites. The remaining 25 ± 8% was exclusively attributed to biomass combustion, consistent with the measurements of biomass-burning markers such as anhydrosugars (levoglucosan and mannosan) and water-soluble potassium (K+). With a combination of the levoglucosan-to-mannosan and levoglucosan-to-K+ ratios, the major source of biomass burning in winter in China is suggested to be combustion of crop residues. The contribution of fossil sources to OC was highest in Beijing (58 ± 5%) and decreased from Shanghai (49 ± 2%) to Xi'an (38 ± 3%) and Guangzhou (35 ± 7%). Generally, a larger fraction of fossil OC was from secondary origins than primary sources for all sites. Non-fossil sources accounted on average for 55 ± 10 and 48 ± 9% of OC and total carbon (TC), respectively, which suggests that non-fossil emissions were very important contributors of urban carbonaceous aerosols in China. The primary biomass-burning emissions accounted for 40 ± 8, 48 ± 18, 53 ± 4 and 65 ± 26% of non-fossil OC for Xi'an, Beijing, Shanghai and Guangzhou, respectively. Other non-fossil sources excluding primary biomass burning were mainly attributed to formation of secondary organic carbon (SOC) from non-fossil precursors such as biomass-burning emissions. For each site, we also compared samples from moderately to heavily polluted days according to particulate matter mass. Despite a significant increase of the absolute mass concentrations of primary emissions from both fossil and non-fossil sources during the heavily polluted events, their relative contribution to TC was even decreased, whereas the portion of SOC was consistently increased at all sites. This observation indicates that SOC was an important fraction in the increment of carbonaceous aerosols during the haze episode in China.

An assessment of the relative influence of a vapor recovery system in reducing occupational exposure to volatile organic compounds in high performance liquid chromatography

Occupational exposures to organic solvents, specifically acetonitrile and methanol, have the potential to cause serious long-term health effects. In the laboratory, these solvents are used extensively in protocols involving the use of high performance liquid chromatography (HPLC). Operators of HPLC equipment may be potentially exposed to these organic solvents when local exhaust ventilation is not employed properly or is not available, which can be the case in many settings. The objective of this research was to characterize the various sites of vapor release in the HPLC process and then to determine the relative influence of a novel vapor recovery system on the overall exposure to laboratory personnel. The effectiveness of steps to reduce environmental solvent vapor concentrations was assessed by measuring exposure levels of acetonitrile and methanol before and after installation of the vapor recovery system. With respect to acetonitrile, the concentration was not statistically significant with p=0.938; moreover, exposure after the intervention was actually higher than prior to intervention. With respect to methanol, the concentration was not statistically significant with p=0.278. This indicates that the exposure to methanol after the intervention was not statistically significantly higher or lower than prior to intervention. Thus, installation of the vapor recovery device did not result in statistically significant reduction in exposures in the settings encountered, and acetonitrile actually increased significantly.^

XCO2 and XCH4 total column measurement during POLARSTERN cruise PS83 (ANT-XXIX/10), north-south gradient

A portable Fourier transform spectrometer (FTS), model EM27/SUN, was deployed onboard the research vessel Polarstern to measure the column-average dry air mole fractions of carbon dioxide (XCO2) and methane (XCH4) by means of direct sunlight absorption spectrometry. We report on technical developments as well as data calibration and reduction measures required to achieve the targeted accuracy of fractions of a percent in retrieved XCO2 and XCH4 while operating the instrument under field conditions onboard the moving platform during a 6-week cruise on the Atlantic from Cape Town (South Africa, 34° S, 18° E; 5 March 2014) to Bremerhaven (Germany, 54° N, 19° E; 14 April 2014). We demonstrate that our solar tracker typically achieved a tracking precision of better than 0.05° toward the center of the sun throughout the ship cruise which facilitates accurate XCO2 and XCH4 retrievals even under harsh ambient wind conditions. We define several quality filters that screen spectra, e.g., when the field of view was partially obstructed by ship structures or when the lines-of-sight crossed the ship exhaust plume. The measurements in clean oceanic air, can be used to characterize a spurious air-mass dependency. After the campaign, deployment of the spectrometer alongside the TCCON (Total Carbon Column Observing Network) instrument at Karlsruhe, Germany, allowed for determining a calibration factor that makes the entire campaign record traceable to World Meteorological Organization (WMO) standards. Comparisons to observations of the GOSAT satellite and concentration fields modeled by the European Centre for Medium-Range Weather Forecasts (ECMWF) Copernicus Atmosphere Monitoring Service (CAMS) demonstrate that the observational setup is well suited to provide validation opportunities above the ocean and along interhemispheric transects.

Prácticas y discursos a debate : Problemáticas en torno a la Verdad

En el marco del 9no Congreso Argentino y 4to Latinoamericano de Educación Física y Ciencias, realizado en la ciudad de La Plata entre los días 13 al 17 de junio del 2011, tuvimos oportunidad de coordinar y comentar conjuntamente con la profesora Evangelina Montero Labat (UNLP/FaHCE), la mesa 7 "Problemas de las prácticas y discursos". En esta reseña se referencian los debates presentes tanto en los trabajos presentados como en los espacios posteriores. Asimismo, se introducen algunas claves teóricas presentes en el pensamiento de Michel Foucault en sintonía con las preocupaciones y problemáticas contenidas en las producciones. Por otra parte, el objetivo no es agotar la complejidad de los trabajos, sino que el lector convocado por la temática de la mesa recurra a partir de este mapa a las fuentes primarias

Prácticas y discursos a debate : Problemáticas en torno a la Verdad

En el marco del 9no Congreso Argentino y 4to Latinoamericano de Educación Física y Ciencias, realizado en la ciudad de La Plata entre los días 13 al 17 de junio del 2011, tuvimos oportunidad de coordinar y comentar conjuntamente con la profesora Evangelina Montero Labat (UNLP/FaHCE), la mesa 7 "Problemas de las prácticas y discursos". En esta reseña se referencian los debates presentes tanto en los trabajos presentados como en los espacios posteriores. Asimismo, se introducen algunas claves teóricas presentes en el pensamiento de Michel Foucault en sintonía con las preocupaciones y problemáticas contenidas en las producciones. Por otra parte, el objetivo no es agotar la complejidad de los trabajos, sino que el lector convocado por la temática de la mesa recurra a partir de este mapa a las fuentes primarias

Prácticas y discursos a debate : Problemáticas en torno a la Verdad

En el marco del 9no Congreso Argentino y 4to Latinoamericano de Educación Física y Ciencias, realizado en la ciudad de La Plata entre los días 13 al 17 de junio del 2011, tuvimos oportunidad de coordinar y comentar conjuntamente con la profesora Evangelina Montero Labat (UNLP/FaHCE), la mesa 7 "Problemas de las prácticas y discursos". En esta reseña se referencian los debates presentes tanto en los trabajos presentados como en los espacios posteriores. Asimismo, se introducen algunas claves teóricas presentes en el pensamiento de Michel Foucault en sintonía con las preocupaciones y problemáticas contenidas en las producciones. Por otra parte, el objetivo no es agotar la complejidad de los trabajos, sino que el lector convocado por la temática de la mesa recurra a partir de este mapa a las fuentes primarias

Study of the radioactivity induced in air by a 15-MeV proton beam.

Radioactivity induced by a 15-MeV proton beam extracted into air was studied at the beam transport line of the 18-MeV cyclotron at the Bern University Hospital (Inselspital). The produced radioactivity was calculated and measured by means of proportional counters located at the main exhaust of the laboratory. These devices were designed for precise assessment of air contamination for radiation protection purposes. The main produced isotopes were 11C, 13N and 14O. Both measurements and calculations correspond to two different irradiation conditions. In the former, protons were allowed to travel for their full range in air. In the latter, they were stopped at the distance of 1.5 m by a beam dump. Radioactivity was measured continuously in the exhausted air starting from 2 min after the end of irradiation. For this reason, the short-lived 14O isotope gave a negligible contribution to the measured activity. Good agreement was found between the measurements and the calculations within the estimated uncertainties. Currents in the range of 120–370 nA were extracted in air for 10–30 s producing activities of 9–22 MBq of 11C and 13N. The total activities for 11C and 13N per beam current and irradiation time for the former and the latter irradiation conditions were measured to be (3.60 ± 0.48) × 10−3 MBq (nA s)−1 and (2.89 ± 0.37) × 10−3 MBq (nA s)−1, respectively.

Aspectos de la medición dinámica instantánea de emisiones de motores. Aplicación al desarrollo de un equipo portátil y una metodología para estudios de contaminación de vehículos en tráfico real.

Esta Tesis Doctoral se encuadra en el ámbito de la medida de emisiones contaminantes y de consumo de combustible en motores de combustión interna alternativos cuando se utilizan como plantas de potencia para propulsión de vehículos ligeros de carretera, y más concretamente en las medidas dinámicas con el vehículo circulando en tráfico real. En este ámbito, el objetivo principal de la Tesis es estudiar los problemas asociados a la medición en tiempo real con equipos embarcados de variables medioambientales, energéticas y de actividad, de vehículos ligeros propulsados por motores térmicos en tráfico real. Y como consecuencia, desarrollar un equipo y una metodología apropiada para este objetivo, con el fin de realizar consiguientemente un estudio sobre los diferentes factores que influyen sobre las emisiones y el consumo de combustible de vehículos turismo en tráfico real. La Tesis se comienza realizando un estudio prospectivo sobre los trabajos de otros autores relativos al desarrollo de equipos portátiles de medida de emisiones (Portable Emission Measurement Systems – PEMS), problemas asociados a la medición dinámica de emisiones y estudios de aplicación en tráfico real utilizando este tipo de equipos. Como resultado de este estudio se plantea la necesidad de disponer de un equipo específicamente diseñado para ser embarcado en un vehículo que sea capaz de medir en tiempo real las concentraciones de emisiones y el caudal de gases de escape, al mismo tiempo que se registran variables del motor, del vehículo y del entorno como son la pendiente y los datos meteorológicos. De esta forma se establecen las especificaciones y condiciones de diseño del equipo PEMS. Aunque al inicio de esta Tesis ya existían en el mercado algunos sistemas portátiles de medida de emisiones (PEMS: Portable Emissions Measurement Systems), en esta Tesis se investiga, diseña y construye un nuevo sistema propio, denominado MIVECO – PEMS. Se exponen, discuten y justifican todas las soluciones técnicas incorporadas en el sistema que incluyen los subsistema de análisis de gases, subsistemas de toma de muestra incluyendo caudalímetro de gases de escape, el subsistema de medida de variables del entorno y actividad del vehículo y el conjunto de sistemas auxiliares. El diseño final responde a las hipótesis y necesidades planteadas y se valida en uso real, en banco de rodillos y en comparación con otro equipos de medida de emisiones estacionarios y portátiles. En esta Tesis se presenta también toda la investigación que ha conducido a establecer la metodología de tratamiento de las señales registradas en tiempo real que incluye la sincronización, cálculos y propagación de errores. La metodología de selección y caracterización de los recorridos y circuitos y de las pautas de conducción, preparación del vehículo y calibración de los equipos forma también parte del legado de esta Tesis. Para demostrar la capacidad de medida del equipo y el tipo de resultados que pueden obtenerse y que son útiles para la comunidad científica, y las autoridades medioambientales en la parte final de esta Tesis se plantean y se presentan los resultados de varios estudios de variables endógenas y exógenas que afectan a las emisiones instantáneas y a los factores de emisión y consumo (g/km) como: el estilo de conducción, la infraestructura vial, el nivel de congestión del tráfico, tráfico urbano o extraurbano, el contenido de biocarburante, tipo de motor (diesel y encendido provocado), etc. Las principales conclusiones de esta Tesis son que es posible medir emisiones másicas y consumo de motores de vehículos en uso real y que los resultados permiten establecer políticas de reducción de impacto medio ambiental y de eficiencia energética, pero, se deben establecer unas metodologías precisas y se debe tener mucho cuidado en todo el proceso de calibración, medida y postratamientos de los datos. Abstract This doctoral thesis is in the field of emissions and fuel consumption measurement of reciprocating internal combustion engines when are used as power-trains for light-duty road vehicles, and especially in the real-time dynamic measurements procedures when the vehicle is being driven in real traffic. In this context, the main objective of this thesis is to study the problems associated with on-board real-time measuring systems of environmental, energy and activity variables of light vehicles powered by internal combustion engines in real traffic, and as a result, to develop an instrument and an appropriate methodology for this purpose, and consequently to make a study of the different factors which influence the emissions and the fuel consumption of passenger cars in real traffic. The thesis begins developing a prospective study on other authors’ works about development of Portable Emission Measurement Systems (PEMS), problems associated with dynamic emission measurements and application studies on actual traffic using PEMS. As a result of this study, it was shown that a measuring system specifically designed for being on-board on a vehicle, which can measure in real time emission concentrations and exhaust flow, and at the same time to record motor vehicle and environment variables as the slope and atmospheric data, is needed; and the specifications and design parameters of the equipment are proposed. Although at the beginning of this research work there were already on the market some PEMS, in this Thesis a new system is researched, designed and built, called MIVECO – PEMS, in order to meet such measurements needs. Following that, there are presented, discussed and justify all technical solutions incorporated in the system, including the gas analysis subsystem, sampling and exhaust gas flowmeter subsystem, the subsystem for measurement of environment variables and of the vehicle activity and the set of auxiliary subsystems. The final design meets the needs and hypotheses proposed, and is validated in real-life use and chassis dynamometer testing and is also compared with other stationary and on-board systems. This thesis also presents all the research that has led to the methodology of processing the set of signals recorded in real time including signal timing, calculations and error propagation. The methodology to select and characterize of the routes and circuits, the driving patterns, and the vehicle preparation and calibration of the instruments and sensors are part of the legacy of this thesis. To demonstrate the measurement capabilities of the system and the type of results that can be obtained and that are useful for the scientific community and the environmental authorities, at the end of this Thesis is presented the results of several studies of endogenous and exogenous variables that affect the instantaneous and averaged emissions and consumption factors (g/km), as: driving style, road infrastructure, the level of traffic congestion, urban and extra-urban traffic, biofuels content, type of engine (diesel or spark ignition) etc. The main conclusions of this thesis are that it is possible to measure mass emissions and consumption of vehicle engines in actual use and that the results allow us to establish policies to reduce environmental impact and improve energy efficiency, but, to establish precise methodologies and to be very careful in the entire process of calibration, measurement and data post-treatment is necessary.

Estudio del abastecimiento energético para un barrio modelo utilizando cogeneración con pila de combustible

El alcance del proyecto es describir las directrices técnicas, la definición de criterios, y la estrategia de suministro de energía (Electricidad. Calefacción y Agua Caliente Sanitaria (ACS)) a un barrio modelo situado en un entorno urbano. De inicio se estudia los diversos modelos energéticos atendiendo a la normativa y tecnología, que se pueden aplicar en un conjunto residencial, dando como resultado el modelo propuesto de abastecimiento energético, mediante calefacción de distrito, que incorporara el diseño de una planta de producción de energía termo-eléctrica o Central de Energías basada en la tecnología de condensación de baja temperatura para calefacción y A.C.S. incluyendo una cogeneración con pila de combustible. Al mismo tiempo se han calculado y diseñado una serie de chimeneas externas para dar cumplida necesidad técnica y legal al proyecto. Estos estudios nos sirven de punto de partida para analizar la amortización de la inversión y por tanto la rentabilidad y viabilidad del proyecto, comparándose con los costes económicos derivados de la generación por sistemas convencionales. Para finalizar se hace mención a las ventajas medioambientales y a los grados de seguridad en la planta de producción ABSTRACT The scope of this work is the description of an energy supply project ( Electricity, heat and hot water ) to a housing development in a urban neibourhood , including technical criteria in their different options. Initially, several solutions are studied based on available technologies and legal restrictions. The final proposal is based on the district hearing model including electricity production in cogeneration via fuel cell technology as well as heating and hot water produced by low temperature condensation boilers It includes calculations and design criteria of the exhaust gases system and chimeneys in compliance with legal requirement in urban areas. This work also includes an economical model including payback, IRR and VAN analysis and an economical comparaison with the standard solutions. Finally, environmental advantages of the preferred solution over other standards as well as safety issues are also presented.

Levels, sources and seasonality of coarse particles (PM10-PM2.5) in three European capitals e implications for particulate pollution control

Coarse particles of aerodynamic diameter between 2.5 and 10 mm (PMc) are produced by a range of natural (windblown dust and sea sprays) and anthropogenic processes (non-exhaust vehicle emissions, industrial, agriculture, construction and quarrying activities). Although current ambient air quality regulations focus on PM2.5 and PM10, coarse particles are of interest from a public health point of view as they have been associated with certain mortality and morbidity outcomes. In this paper, an analysis of coarse particle levels in three European capitals (London, Madrid and Athens) is presented and discussed. For all three cities we analysed data from both traffic and urban background monitoring sites. The results showed that the levels of coarse particles present significant seasonal, weekly and daily variability. Their wind driven and non-wind driven resuspension as well as their roadside increment due to traffic were estimated. Both the local meteorological conditions and the air mass history indicating long-range atmospheric transport of particles of natural origin are significant parameters that influence the levels of coarse particles in the three cities especially during episodic events.

Emission factors from road dust resuspension in a Mediterranean freeway

Particulate matter emissions from paved roads are currently one of the main challenges for a sustainable transport in Europe. Emissions are scarcely estimated due to the lack of knowledge about the resuspension process severely hampering a reliable simulation of PM and heavy metals concentrations in large cities and evaluation of population exposure. In this study the Emission Factors from road dust resuspension on a Mediterranean freeway were estimated per single vehicle category and PM component (OC, EC, mineral dust and metals) by means of the deployment of vertical profiles of passive samplers and terminal concentration estimate. The estimated PM10 emission factors varied from 12 to 47 mg VKT?1 (VKT: Vehicle Kilometer Traveled) with an average value of 22.7 ? 14.2 mg VKT?1. Emission Factors for heavy and light duty vehicles, passenger cars and motorbikes were estimated, based on average fleet composition and EPA ratios, in 187e733 mg VKT?1, 33e131 VKT?1, 9.4e36.9 VKT?1 and 0.8e3.3 VKT?1, respectively. These range of values are lower than previous estimates in Mediterranean urban roads, probably due to the lower dust reservoir on freeways. PM emitted material was dominated by mineral dust (9e10 mg VKT?1), but also OC and EC were found to be major components and approximately 14 e25% and 2e9% of average PM exhaust emissions from diesel passenger cars on highways respectively.

On the formation of nitrogen oxides in the combustion processes of hydrogen in air

A research programme is being carried out at the Institute Nacional de Tecnica Aeroespacial of Spain, on several aspects of the formation of nitrogen oxides in continuous flow combustion systems, considering hydrogen and hydrocarbons as fuels. The research programme is fundamentally oriented on the basic aspects of the problem, although it also includes the study of the influence on the formation process of several operational and design variables of the combusters, such as type of fuels, fuel/air ratio, degree of mixing in premixed type flames, existence of droplets as compared with homogeneous combustion.This problem of nitrogen oxides formation is receiving lately great attention, specially in connection with automobile reciprocating engines and aircraft gas turbines. This is due to the fact of the increasing frequency and intensity of photochemical hazes or smog, typical of urban areas submitted to strong solar radiation, which are originated by the action on organic compounds of the oxidants resulting from the photochemical decomposition of nitrogen dioxide N02. In the combustion process almost all nitrogen oxides are in form of NO. This nitric oxide reacts with the oxygen of the air and forms N02, this reaction only taking place in or near the exhaust of tne motors, since the N0-02 reaction becomes frozen for the concentration existing in the atmosphere.

Science with an electrodynamic tether

Ionospheric interaction experiments using a conductive, fully bare tether are discussed. With an optimal design, requiring 1.15 mm diameter and 7.5 km full length for a collected current of 0.87 A at day conditions, the tether radiates 0.33 watts as Fast Magnetosonic waves and 0.16 watts as Alfven waves. Secondary keV electrons are produced over a 6.5 km length, giving raise to noticeable auroral effects in the D-layer, at low geomagnetic latitudes. A preliminary design of the experiment, to be implemented on either a satellite or a Station, has been carried out. An ejector gives an initial velocity to an end mass, a free spool of tether unwinding from that mass during a first stage of deployment; other phases are monitored through the tether velocity, driving a reel with an unwinding device.

Determinación de la distribución de tamaño y número de partículas provenientes de motores diesel operando en trafico real con equipos embarcados

El presente trabajo se propone determinar la distribución de tamaño y número de partículas nanométricas provenientes de motores diésel con equipos embarcados en tráfico extraurbano. Para ello, se utilizaron equipos de medición de última generación en condiciones promedio de conducción en tráfico extraurbano por más de 800 km a lo largo del trayecto Madrid-Badajoz-Madrid mediante un vehículo característico del parque automotor español y se implementaron métodos novedosos y pioneros en el registro de este tipo de emisiones. Todo ello abre el camino para líneas de investigación y desarrollo que contribuirán a entender, dimensionar y cualificar el comportamiento de las partículas, así como su impacto en la calidad de vida de la población. El estudio hace dos grandes aportes al campo. Primero, permite registrar las emisiones en condiciones transitorias propias del tráfico real. Segundo, permite mantener controladas las condiciones de medición y evita la formación aleatoria de partículas provenientes de material volátil, gracias al sistema de adecuación de la muestra de gases de escape incorporado. Como resultado, se obtuvo una muestra abundante y confiable que permitió construir modelos matemáticos para calcular la emisión de partículas nanométricas, ultrafinas, finas y totales sobre las bases volumétrica, espacial y temporal en función de la pendiente del perfil orográfico de la carretera, siempre y cuando esté dentro del intervalo ±5.0%. Estos modelos de cálculo de emisiones reducen tanto los costos de experimentación como la complejidad de los equipos necesarios, y fundamentaron el desarrollo de la primera versión de una aplicación informática que calcula las partículas emitidas por un motor diésel en condiciones de tráfico extraurbano ("Partículas Emitidas por Motores Diésel, PEMDI). ABSTRACT The purpose of this research is to determine the distribution of size and number of nanometric particles that come from diesel engines by means of on-board equipment in extra-urban traffic. In order to do this, cutting-edge measuring equipment was used under average driving conditions in extra-urban traffic for more than 800 km along the Madrid-Badajoz-Madrid route using a typical vehicle from Spain's automotive population and innovative, groundbreaking registering methods for this type of emissions were used. All this paves the way for lines of research and development which should help understand, measure and characterize the behavior of such particles, as well as their impact in the quality of life of the general population. The study makes two important contributions to the field. First, it makes it possible to register emissions under transient conditions, which are characteristic to real traffic. Secondly, it provides a means to keep the measuring conditions under control and prevents the random formation of particles of volatile origin through the built-in adjustment system of the exhaust gas sample. As a result, an abundant and reliable sample was gathered, which enabled the building of mathematical models to estimate the emission of nanometric, ultrafine, fine and total particles on volumetric, spatial and temporal bases as a function of the orographic outline of the road within a ±5.0% range. These emission estimating models lower both the experimentation costs and the required equipment's complexity, and they provided the basis for the development of a first software application version that estimates the particles emitted from diesel engines under extra-urban traffic conditions (Partículas Emitidas por Motores Diésel, PEMDI).

Clasificación de zonas en instalaciones para vehículos propulsados por GNC

El presente proyecto tiene como objetivo principal el análisis de la viabilidad de estacionamiento de vehículos propulsados por gas natural comprimido (GNC) desde el punto de vista de formación de atmosferas potencialmente explosivas en los garajes subterráneos. Además se ha realizado una breve introducción sobre el GNC explicando el origen, la composición y los diferentes usos que tiene. Se ha realizado la evaluación de riesgos asociados a la utilización de vehículos propulsados por gas natural y estimación de tasas de escape en el circuito de combustible de los vehículos propulsados por GNC. Para ello se ha aplicado la normativa UNE EN 60079-10 traspuesta en España mediante el Real Decreto del 681/2003 sobre la salud y la seguridad de los trabajadores y el Real Decreto 400/1996 sobre aparatos y sistemas de protección para su uso en atmósferas explosivas. Finalmente se han expuesto las medidas de prevención y protección necesarias para prevenir la generación de atmosferas potencialmente explosivas en los garajes subterráneos y se han detallado los procedimientos y las operaciones que han de realizarse. En las conclusiones se han explicado las acciones más importantes que deben emprenderse para mejorar la seguridad de personas e instalaciones en las áreas de riesgo por presencia de atmósferas potencialmente explosivas. ABSTRACT The main objective of this project is to analyze the viability of the parking of vehicles powered by compressed natural gas (CNG) in the underground garages from the point of view of generated of potentially explosive atmospheres in garages. A brief introduction about the CNG explaining the origin, composition and the different uses that it has is also included. An assessment of the risks associated with the use of vehicles powered by natural gas has been provided as well as an estimate of the exhaust rates on the gas circuit of CNG vehicles. In order to do that, the standard UNE EN 60079-10 transposed in Spain by the Royal Decree 681/2003 about the health and safety of workers and the Royal Decree 400/1996 about equipment and protection systems to be used in explosive atmospheres have been applied. Finally, the necessary preventive and protective measures to prevent the generation of potentially explosive atmospheres in underground garages have been presented and the procedures and operations to be performed have been detailed. In the conclusions, the most important actions to be taken in order to improve the safety of people and facilities in the areas at risk of having potentially explosive atmospheres have been described.