Eletrólise de resíduos poluidores: I - Efluente de uma indústria liofilizadora de condimentos

Wastewater from a seasoning freeze-drying industry was electrolysed to increase its biodegradability. Stainless-steel electrodes were used at 9.09 A/m², for up to 80 min. Conductivity, pH, biochemical (BOD) and chemical (COD) oxygen demands, Daphnia similis acute toxicity bioassays, and bacteria counting through the plate count agar method were determined after different times of electrolysis. The results (e.g. higher BOD and lower COD) showed that the biodegradability of the wastewater was significantly increased; furthermore, Fe2+ ions liberated by the electrodes cause microorganisms to die and, when oxidised to Fe3+, contribute for the flocculation and sedimentation of solid residues.

Porta-amostras polimérico para espectroscopia infravermelha de sistemas líquidos aquosos ou orgânicos

Infrared spectroscopy laboratories works under permanent care with respect to water contamination, mainly in liquid samples. In this case crystal plates destruction or damage are frequent, increasing the operational expenses. On the other hand, the laboratory which produces such samples must be very careful in drying liquid samples. In this work we develop a simple and inexpensive way to operate in such conditions using polypropylene and HDPE films which were thermally soldered resulting little containers or sample holders. The spectra of sample/sample holder is achieved having the sample holder as background.

Laitepuhdistamon ylijäämäliete ja sen kuiva-ainepitoisuuden nostaminen

Työssä tutkittiin pienpuhdistamon ylijäämälietteen ominaisuuksia ja käyttäytymistä pienpuhdistamon ylijäämälietteen tiivistys- tai kuivausmenetelmän kehittämisen teoriapohjaksi. Työ sisältää myös lietteiden tiivistysmenetelmien kustannustarkastelua. Kokeellisessa osuudessa käytettiin työn teettäjän Oy KWH Pipe Ab:n valmistamien pienpuhdistamojen ylijäämälietettä. Tutkittava ylijäämäliete oli peräisin asukasvastineluvultaan 5–95 pienistä aktiivilietelaitepuhdistamoista. Tiivistys- tai kuivausmenetelmän kehittämisen tarkoituksena on saavuttaa kustannussäästöjä pienpuhdistamon ylijäämälietteen kuljetusmatkojen vähentämisen kautta. Soveltuvia vertailtavia sovelluksia ovat staattiseen laskeuttamiseen perustuvat menetelmät, mekaaniset ruuvi- ja linkokuivaimet, kuivauslava ja flotaatio. Tarkasteltavien menetelmien tuli olla käytöltä ja huollolta sekä käyttökuluiltaan edullisia ja yksinkertaisia. Ylijäämälietteiden ominaisuuksia ja käyttäytymistä tutkittiin kirjallisuuslähteistä ja käytännön kokein. Kokeissa tarkasteltiin ylijäämälietteen laskeutumis- ja nousuominaisuuksia, redox-potentiaalin vaihtelua seisovassa näytteessä ja flotaation onnistumista testattavalle lietteelle. Kokeet tehtiin kullakin kerralla eri ajankohtana otetuille lietenäytteille, käytettyjä puhdistamoja oli useita ja mitoitus, kuormitus sekä jäteveden laatu vaihteli paljon.

Produção de dióxido de manganês eletrolítico para uso em baterias de lítio

The e phase of electrolytic manganese dioxide (EMD) is the structural form most easily converted in the LiMn2O4 spinel used as cathode in lithium batteries. Thus, employing titanium as anode, a study of electrolysis parameters was carried out in order to determine the best conditions to produce an e-EMD suitable for that spinel preparation. The influence of solution temperature (65oC and 90oC) and current density (between 1 mA/cm2 and 17.5 mA/cm2) on the anode potential and the EMD properties was investigated using an aqueous 2.0 mol/L MnSO4 + 0.30 mol/L H2SO4 solution. In any of the electrolysis conditions tested only the e-EMD structure was obtained, but its specific surface area varied with the applied current density and temperature. Drying the e-EMD at temperatures between 60oC and 120oC did not cause any phase changes. To produce a suitable EMD at the highest current density possible without passivation of the titanium anode, the best electrolysis parameters were determined to be 90oC and 15 mA/cm2. The e-EMD thus obtained had a specific surface area (BET) of ca. 65 m2/g.

Kuusiviilun esikuivaus puristamalla

Tutkimuksen lähtökohtana oli selvittää, voidaanko viilun valmistusprosessiin liittää uusi työvaihe, viilun esikuivaus. Esikuivauksen tarkoituksena on poistaa kosteutta viiluista ennen varsinaista kuivausta ja lisätä näin kuivauskapasiteettia. Tehdyissä tutkimuksissa viilut esikuivattiin nipuissa puristamalla. Muuttujina esikuivauksessa toimivat puristusaika ja -paine. Niiden määrittelyn lähtökohtana pidettiin sitä, etteivät viilun ominaisuudet saa merkittävästi heikentyä esikuivauksen aikana ja samalla viiluista on saatava mahdollisimman paljon kosteutta pois. Aikaisempien tutkimusten avulla selvitettiin vanerin valmistuksen, viilun kuivauksen sekä viilun esikuivauksen teoriaa. Lisäksi selvitettiin puun ominaisuuksien antamia mahdollisuuksia ja rajoitteita esikuivaukseen liittyen. Tutkimus koostui kahdesta osasta: laboratorio- ja tehdastutkimuksista. Laboratoriotutkimuksen tarkoituksena oli toimia tehdastutkimuksen esitutkimuksena. Laboratoriotutkimuksessa tutkittiin ainoastaan esikuivauksen vaikutusta märille viiluille. Tehdastutkimusosiossa esikuivatuista viiluista valmistettiin normaalin vanerinvalmistusprosessin kautta levyjä, joiden ominaisuuksia verrattiin normaaleista viiluista valmistettuihin vanereihin. Viilujen esikuivauksen todettiin pienentävän kuusiviilujen kosteuspitoisuutta. Tämän lisäksi kosteuspitoisuuden muutokset esikuivauksen aikana tapahtuivat tasaisesti niin yksittäisen viilun kuin viilunipunkin sisällä. Esikuivatuista viiluista valmistetut vanerilevyt täyttivät kaikki standardien sekä vanerin laadunvalvontasopimuksen asettamat vaatimukset. Esikuivauksen haitaksi tutkimuksissa todettiin viilun paksuuden pienentymä. Ennen esikuivauksen soveltamista teolliseen käyttöön nähtiin tarvetta lisätutkimukselle, jossa tulisi selvittää suurempien viilunippukokojen esikuivaamista sekä niiden varsinaista kuivaamista heti esikuivauksen jälkeen.

Avaliacão de programas de aquecimento para espectrometria de absorção atômica com atomizacão eletrotérmica em filamento de tungstênio

A tungsten coil atomizer was used to investigate the effect of heating programs with constant or variable drying temperatures on the atomization of Al, Cd, Cr and Pb. The variation of the surface temperature in the tungsten coil furnace can occur during each heating step due to the design of the power supply, that may apply constant voltages during a programmed time. For volatile elements (Cd), losses in sensitivity were observed when the program with a variable temperature was used. On the other hand, these effects are negligible for less volatile elements (Al and Cr) and any tested program, in different acidic media, could be used without appreciable changes in sensitivities. The results allow the establishment of proper heating programs for elements with different thermochemical behavior in the tungsten coil atomizer.

Dióxido de titânio sol-gel: propriedades e comportamento eletrocrômico

Titanium dioxide was prepared by hydrolysis and polycondensation of titanium tetraisopropoxide. TiO2 films were obtained by spin coating of the precursor solution on ITO substractes (glass covered with indium doped tin oxide). Films were prepared using different temperatures and hydrochloric acid contents. The effect of the drying temperature of the films (100 or 400ºC) was also investigated. TiO2 films were characterized by cyclic voltammetry, chronoamperometry, ultraviolete-visible spectroscopy, scanning electron microscopy and X-ray diffractrometry.

Esfoliação e hidratação da caulinita após intercalação com uréia

Well-ordered Georgia kaolinite (Kga-1b) obtained from the source Clay Repository of the Clay Minerals Society (USA) was intercalated with urea using grinding procedures. To achieve complete intercalation 20% of urea (in weight) was used, producing Al2Si2O5(OH)4 (N2H4CO)0,86 with an interplanar basal spacing of 1,08nm. After washing with water under ultrasound stirring at 363K, urea was completely removed and kaolinite was partially exfoliated. After drying under air, the material was converted to hydrated kaolinite with the composition Al2Si2O5(OH)4 (H2O)0,64 and an interplanar basal spacing of 0,84nm. In this compound, water molecules positioned between the layers of the silicate can be removed after calcination at 573K, regenerating structurally disordered kaolinite.

Síntese de membranas cerâmicas via método sol-gel utilizando TEOS e N,N-dimetilformamida

In this work we obtained microporous and mesoporous silica membranes by sol-gel processing. Tetraethylortosilicate (TEOS) was used as precursor. Nitric acid was used as catalyst. In order to study the affect of N,N-dimethylformamide (NDF) as drying additive, we used a molar ratio TEOS/NDF of 1/3. The performance of N,N-dimethylformamide was evaluated through monolithicity measurements. The structural evolutions occurring during the sol-gel transition and in the interconnected network of the membranes during thermal treatment were monitored by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyses and nitrogen sorption. We noted that in the presence of N,N-dimethylformamide, polymerization goes through a temporary stabilization of oligomers. The Si-O(H) bonds are stronger and belong to a more cross-linked structure for the N,N-dimethylformamide containing sol. The membranes obtained in the presence of N,N-dimethylformamide have larger surface area and its pore structure is in the range of mesoporous. The membranes obtained without additive have pore structure in the range of microporous.

Comportamento térmico da caulinita hidratada

Well-ordered kaolinite from the Brazilian Amazon Region (State of Pará) was initially reacted at 60 °C with a water dimethylsulfoxide mixture. After washing and characterisation, the resulting material was washed several times with methanol and in the final step with water. The water molecules displace the previously dimethylsulfoxide intercalated molecules and two different hydrated kaolinites were obtained. An unstable phase characterized by an interplanar basal distance of 0,996 nm that after drying collapse to the stable 0,844 nm hydrated kaolinite. The dehydration of the sample to disordered kaolinite was accompanied by Powder X-ray Diffractometry, thermal analysis (simultaneous TG and DSC) and FTIR spectroscopy.

Desenvolvimento de um sistema automatizado para a fabricação de filmes automontados

In this technical note, we describe the construction of a low-cost computer controlled device for layer-by-layer film fabrication. The software allows to control multiple material deposition, washing and drying steps and the time for each operation. To test the device, we produced and characterized self-assembled films of conductive polymers by alternating poly(o-methoxyaniline) (POMA) and poly(3-thiophene acetic acid) (PTAA) via the layer-by-layer technique.

Experimentos didáticos envolvendo radiação microondas

Theoretical and practical aspects of the use of microwave-assisted strategies in chemistry are introduced for students using simple and safe experiments employing a domestic oven. Three procedures are proposed for evaluating the distribution of microwave radiation inside the microwave oven cavity: (1) variation of the volume of marshmallows; (2) drying of filter paper wetted with Co(II) solution, and (3) variation of water temperature, after microwave-assisted heating. These experiments establish the position with the highest incidence of microwave radiation in the oven cavity, which was chosen for the synthesis of salicylic acid acetate. This synthesis was performed in 5 min of heating and the yield was around 85%. All experiments can be carried out in a 4 h lab-session using low-cost instrumentation.

Preparação de amostra de fígado bovino e estudo de micro homogeneidade para a determinação de Cd E Pb por espectrometria de absorção atômica com atomização eletrotérmica e amostragem direta de sólido

This work describes a systematic study for bovine liver sample preparation for Cd and Pb determination by solid sampling electrothermal atomic absorption spectrometry. Samples were prepared using different procedures: (1) drying in a household microwave oven followed by drying in a stove at 60 ºC until constant mass, and (2) freeze-drying. Ball and cryogenic mills were used for grinding. Particle size, sample size and micro sample homogeneity were investigated. All prepared samples showed good homogeneity (He < 10) even for low sample mass, but samples dried in a microwave oven/stove and ground in a ball mill presented the best homogeneity.

A convenient method for the determination of moisture in aromatic plants

A method is proposed for the determination of the moisture content of aromatic plants. This method is based on the co-distillation of the starting material in a modified Clevenger apparatus with four organic solvents (toluene, cyclohexane, dichloromethane and carbon tetrachloride). The results were compared with those obtained by oven drying at 105 ºC and steam distillation of the essential oil. The efficiencies of the methods were shown to be equivalent. The solvent distillation method was more practical, especially with respect to operating time (2 h).

Optimization of a heatset dryer

The objective of the thesis was to examine the possibilities in designing better performing nozzles for the heatset drying oven in Forest Pilot Center. To achieve the objective, two predesigned nozzle types along with the replicas of the current nozzles in the heatset drying oven were tested on a pilot-scale dryer. During the runnability trials, the pilot dryer was installed between the last printing unit and the drying oven. The two sets of predesigned nozzles were consecutively installed in the dryer. Four web tension values and four different impingement air velocities were used and the web behavior during the trial points was evaluated and recorded. The runnability in all trial conditions was adequate or even good. During the heat transfer trials, each nozzle type was tested on at least two different nozzle-to-surface distances and four different impingement air velocities. In a test situation, an aluminum plate fitted with thermocouples was set below a nozzle and the temperature measurement of each block was logged. From the measurements, a heat transfer coefficient profile for the nozzle was calculated. The performance of each nozzle type in tested conditions could now be rated and compared. The results verified that the predesigned simpler nozzles were better than the replicas. For runnability reasons, there were rows of inclined orifices on the leading and trailing edges of the current nozzles. They were believed to deteriorate the overall performance of the nozzle, and trials were conducted to test this hypothesis. The perpendicular orifices and inclined orifices of a replica nozzle were consecutively taped shut and the performance of the modified nozzles was measured as before, and then compared to the performance of the whole nozzle. It was found out, that after a certain nozzle-to-surface distance the jets from the two nozzles would collide, which deteriorates the heat transfer.