Friction of sliding surfaces carrying adsorbed lubricant layers

In concentrated contacts the behaviour of lubricants is much modified by the high local pressures: changes can arise both from molecular ordering within the very thin film lubricant layers present at the interface as well as from the deposition on the component surfaces of more solid-like polymeric boundary layers. These 'third bodies' separating the solid surfaces may have rheological or mechanical properties very different from those observed in the bulk. Classical elasto-hydrodynamic theory considers the entrapped lubricant to exhibit a piezo-viscous behaviour while the conventional picture of more solid boundary lubricant layers views their shear strength r as being linearly dependent on local pressure p, so that T = TO + ap where TO and a are constants. If TO is relatively small, then the coefficient of friction \i = T Ip ~ a and so Amonton's laws are recovered. However, the properties of adsorbed or deposited surface films, or indeed other third bodies such as debris layers, may be more complex than this. A preliminary study has looked quantitatively at the influence of the pressure dependence of the shear strength of any surface layer on the overall friction coefficient of a contact which is made up of an array of asperities whose height varies in a Gaussian manner. Individual contact points may be elastic or plastic. The analysis results in plots of coefficient of friction versus the service or load parameter PIH&NRa where P is the nominal pressure on the contact, HS the hardness of the deforming surface, N the asperity density, R the mean radius of curvature of the asperities, and a is the standard deviation of their height distribution. In principle, any variation oft withp can be incorporated into the model; however, in this initial study we have used data on colloidal suspensions from the group at the Ecole Centrale de Lyon as well as examining the effect of functional relationships of somewhat greater complexity than a simple linear form. Results of the analysis indicate that variations in fj. are possible as the load is varied which depend on the statistical spread of behaviour at individual asperity contacts. The value of this analysis is that it attempts to combine the behaviour of films on the molecular scale with the topography of real engineering surfaces and so give an indication of the effects at the full-size or macro-scale that can be achieved by chemical or molecular surface engineering.

Movement of deposited water on turbomachinery rotor blade surfaces

A theoretical approach for calculating the movement of liquid water following deposition onto a turbomachine rotor blade is described. Such a situation can occur during operation of an aero-engine in rain. The equation of motion of the deposited water is developed on an arbitrarily oriented plane triangular surface facet. By dividing the blade surface into a large number of facets and calculating the water trajectory over each one crossed in turn, the overall trajectory can be constructed. Apart from the centrifugal and Coriolis inertia effects, the forces acting on the water arise from the blade surface friction, and the aerodynamic shear and pressure gradient. Non- dimensionalisation of the equations of motion provides considerable insight and a detailed study of water flow on a flat rotating plate set at different stagger angles demonstrates the paramount importance of blade surface friction. The extreme cases of low and high blade friction are examined and it is concluded that the latter (which allows considerable mathematical generalisation) is the most likely in practice. It is also shown that the aerodynamic shear force, but not the pressure force, may influence the water motion. Calculations of water movement on a low-speed compressor blade and the fan blade of a high bypass ratio aero-engine suggest that in low rotational speed situations most of the deposited water is centrifuged rapidly to the blade tip region. Copyright © 2006 by ASME.

Ink-jet printing for patterning engineering surfaces

This work explored the use of industrial drop-on-demand inkjet printing for masking steel surfaces on engineering components, followed by chemical etching, to produce patterned surfaces. A solvent-based ink was printed on to mild steel samples and the influences of substrate topography and substrate temperature were investigated. Contact angle measurements were used to assess wettability. Regular patterns of circular spots (∼60 /on diameter) and more complex mask patterns were printed. Variation of the substrate temperature had negligible effect on the final size of the printed drops or on the resolution achieved. Colored optical interference fringes were observed on the dried ink deposits and correlated with film thickness measurements by whitelight interferometry.

Characterisation and simulation of asphalt road surfaces

Accurate simulation of rolling-tyre vibrations, and the associated noise, requires knowledge of road-surface topology. Full scans of the surface types in common use are, however, not widely available, and are likely to remain so. Ways of producing simulated surfaces from incomplete starting information are thus needed. In this paper, a simulation methodology based solely on line measurements is developed, and validated against a full two-dimensional height map of a real asphalt surface. First the tribological characteristics-asperity height, curvature and nearest-neighbour distributions-of the real surface are analysed. It is then shown that a standard simulation technique, which matches the (isotropic) spectrum and the probability distribution of the height measurements, is unable to reproduce these characteristics satisfactorily. A modification, whereby the inherent granularity of the surface is enforced at the initialisation stage, is introduced, and found to produce simulations whose tribological characteristics are in excellent agreement with the measurements. This method will thus make high-fidelity tyre-vibration calculations feasible for researchers with access to line-scan data only. In addition, the approach to surface tribological characterisation set out here provides a template for efficient cataloguing of road textures, as long as the resulting information can subsequently be used to produce sample realisations. A third simulation algorithm, which successfully addresses this requirement, is therefore also presented. © 2011 Elsevier B.V.

Experimental evidence of flutter and divergence instabilities induced by dry friction

Flutter and divergence instabilities have been advocated to be possible in elastic structures with Coulomb friction, but no direct experimental evidence has ever been provided. Moreover, the same types of instability can be induced by tangential follower forces, but these are commonly thought to be of extremely difficult, if not impossible, practical realization. Therefore, a clear experimental basis for flutter and divergence induced by friction or follower-loading is still lacking. This is provided for the first time in the present article, showing how a follower force of tangential type can be realized via Coulomb friction and how this, in full agreement with the theory, can induce a blowing-up vibrational motion of increasing amplitude (flutter) or an exponentially growing motion (divergence). In addition, our results show the limits of a treatment based on the linearized equations, so that nonlinearities yield the initial blowing-up vibration of flutter to reach eventually a steady state. The presented results give full evidence to potential problems in the design of mechanical systems subject to friction, open a new perspective in the realization of follower-loading systems and of innovative structures exhibiting 'unusual' dynamical behaviors. © 2011 Elsevier Ltd.

Seismic behaviour of anchored quay walls with dry backfill

The seismic behaviour of anchored sheet pile walls is a complex soil-structure interaction problem. Damaged sheet pile walls are very expensive to repair and their seismic behaviour needs to be investigated in order to understand their possible mechanisms of failure. The research described in this paper involves both centrifuge testing and Finite Element (FE) analyses aimed at investigating the seismic behaviour of an anchored sheet pile wall in dry sand. The model wall is tied to the backfill with two tie rods connected to an anchor beam. The accelerations of the sheet pile wall, the anchor beam and the soil around the wall were measured using miniature piezoelectric accelerometers. The displacement at the tip of the wall was also measured. Stain gauges at five different locations on the wall were used to measure the bending moments induced in the the wall. The anchor forces in the tie rods were also measured using load cells. The results from the centrifuge tests were compared with 2-D, plane strain FE analyses conducted using DIANA-SWANDYNE II and the observed seismic behaviour was explained in the light of these findings. © 2011 Taylor & Francis.

The characteristics of distribution and change of the seawater temperature and salinity of Cai river estuary and Northern Part of Nha Trang bay in the dry and rainy season

In this paper, some results of analyzing the hydrographic characteristics of the seawater temperature and salinity are presented. The received results showed that: in dry season, the influence of the Cai river water has is limited in Cai river estuary with the approximate transferable distance from the river mouth to the open sea of about 1 km. The isohaline 32%o could be defined as the separate boundary of the Cai river water; In rainy season, due to the river water discharges are high, the influence of Cai river water could be transferred to the open sea and island areas. The immerge of the Cai river water in the open sea areas in rainy season has changed the vertical structure of salinity and temperature in the northern part of Nhatrang bay. In both seasons, the Cai river water have influenced in the surface water layers 0 - 2m and the water layers deeper than 2m are influenced by the sea waters with the salinity of higher than 32%o.

Designing of a single pack wash primer for aluminium surfaces in a marine environment

Design aspects and comparative performances of different laboratory formulations of wash primers were studied under laboratory and field conditions with reference to scratch hardness, flexibility, stability, resistance to corrosion and adhesiveness. The different formulations of single pack wash primers tested have shown superiority of the formulation prepared out of “mowital” and that it is comparable in performance to double pack wash primer.

Studies on thermal deffusivity [i.e. diffusivity] and conductivity of fresh and dry fish

Thermal diffusivity (α) and conductivity (K) of fresh and dry cured fish at different moisture levels were investigated by a calorimeter (regular regime) method and transient line source technique. Thermal conductivity has a linear correlation with packing density and percentage water content. K values calculated from formula method and line source technique are comparable.

Removal of fungus and prevention of fungal reinfestation in stored dry salted fish

A simple and effective method is described for converting dry fish products infested with fungus and red halophilic bacteria to acceptable ones. Washing, drying and then smearing with a mixture of 3% sodium propionate in dry, refined salt in a ratio of 1 part mixture: 10 parts dry fish resulted in the fish having a shelf life of 5 months.

Antioxidant effect of betel leaf extract on dry-cured fish

The effect of betel leaf (Piper betle Linn.) extract on control of autoxidation of fat in dry fish has been studied. Oil sardine has been selected for experiments since it contains very high amount of fat. The treatments were given with 5% (w/v) betel leaf extract in water at different stages of salt curing. FFA, PV and TVN values of the samples were determined periodically to assess the keeping quality and autoxidation. The sample, prepared by dipping the fish in the extract immediately after salting and then drying as usual, was found to have better keeping qualities.

Comparative efficiency of different surfaces for drying fish

The efficiency of four different drying surfaces, namely, cement platform, palmyrah leaf mat, aluminum tray and stretched net for drying fish were studied using sciaenids, mullet and perch. All the drying surfaces were found to be equally efficient. The cheaper and locally available palmyrah leaf mat or stretched net can replace costly cement platform and aluminium tray for efficient drying of fish.

Quality of dry fish from markets in Andhra Pradesh

Dry fish samples were procured from different fish markets and subjected to biochemical and bacteriological evaluation for assessing quality. The quality of market samples was compared with the samples dried in laboratory and in the mechanical drier [sic]. Most of the market samples had high moisture and sand contents. TVN values of market samples were high showing poor quality of the finished product.