Design, Calibration, and Evaluation of Depth-of-Interaction-Capable PET Detector Modules

High-resolution, small-bore PET systems suffer from a tradeoff between system sensitivity, and image quality degradation. In these systems long crystals allow mispositioning of the line of response due to parallax error and this mispositioning causes resolution blurring, but long crystals are necessary for high system sensitivity. One means to allow long crystals without introducing parallax errors is to determine the depth of interaction (DOI) of the gamma ray interaction within the detector module. While DOI has been investigated previously, newly available solid state photomultipliers (SSPMs) well-suited to PET applications and allow new modules for investigation. Depth of interaction in full modules is a relatively new field, and so even if high performance DOI capable modules were available, the appropriate means to characterize and calibrate the modules are not. This work presents an investigation of DOI capable arrays and techniques for characterizing and calibrating those modules. The methods introduced here accurately and reliably characterize and calibrate energy, timing, and event interaction positioning. Additionally presented is a characterization of the spatial resolution of DOI capable modules and a measurement of DOI effects for different angles between detector modules. These arrays have been built into a prototype PET system that delivers better than 2.0 mm resolution with a single-sided-stopping-power in excess of 95% for 511 keV g's. The noise properties of SSPMs scale with the active area of the detector face, and so the best signal-to-noise ratio is possible with parallel readout of each SSPM photodetector pixel rather than multiplexing signals together. This work additionally investigates several algorithms for improving timing performance using timing information from multiple SSPM pixels when light is distributed among several photodetectors.

CHARACTERIZATION OF THE COUNT RATE PERFORMANCE AND EVALUATION OF THE EFFECTS OF HIGH COUNT RATES ON MODERN GAMMA CAMERAS

CHARACTERIZATION OF THE COUNT RATE PERFORMANCE AND EVALUATION OF THE EFFECTS OF HIGH COUNT RATES ON MODERN GAMMA CAMERAS Michael Stephen Silosky, B.S. Supervisory Professor: S. Cheenu Kappadath, Ph.D. Evaluation of count rate performance (CRP) is an integral component of gamma camera quality assurance and measurement of system dead time (τ) is important for quantitative SPECT. The CRP of three modern gamma cameras was characterized using established methods (Decay and Dual Source) under a variety of experimental conditions. For the Decay method, input count rate was plotted against observed count rate and fit to the paralyzable detector model (PDM) to estimate τ (Rates method). A novel expression for observed counts as a function of measurement time interval was derived and the observed counts were fit to this expression to estimate τ (Counts method). Correlation and Bland-Altman analysis were performed to assess agreement in estimates of τ between methods. The dependencies of τ on energy window definition and incident energy spectrum were characterized. The Dual Source method was also used to estimate τ and its agreement with the Decay method under identical conditions and the effects of total activity and the ratio of source activities were investigated. Additionally, the effects of count rate on several performance metrics were evaluated. The CRP curves for each system agreed with the PDM at low count rates but deviated substantially at high count rates. Estimates of τ for the paralyzable portion of the CRP curves using the Rates and Counts methods were highly correlated (r=0.999) but with a small (~6%) difference. No significant difference was observed between the highly correlated estimates of τ using the Decay or Dual Source methods under identical experimental conditions (r=0.996). Estimates of τ increased as a power-law function with decreasing ratio of counts in the photopeak to the total counts and linearly with decreasing spectral effective energy. Dual Source method estimates of τ varied as a quadratic with the ratio of the single source to combined source activities and linearly with total activity used across a large range. Image uniformity, spatial resolution, and energy resolution degraded linearly with count rate and image distorting effects were observed. Guidelines for CRP testing and a possible method for the correction of count rate losses for clinical images have been proposed.

Organizational perspectives on the management and evaluation of large -scale multicenter controlled clinical trials: An exploratory study of participation in the beta -blocker heart attack trial

A review of literature related to appointment-keeping served as the basis for the development of an organizational paradigm for the study of appointment-keeping in the Beta-blocker Heart Attack Trial (BHAT). Features of the organizational environment, demographic characteristics of BHAT enrollees, organizational structure and processes and previous organizational performance variables were measured so as to provide exploratory information relating to the appointment-keeping behavior of 3,837 participants enrolled at thirty-two Clinical Centers. Results suggest that the social context of individual behavior is an important consideration for the understanding of patient compliance. In particular, the degree to which previous organizational performance--as measured by obtaining recruitment goals--and the ability to utilize resources had particularly strong bivariate associations with appointment-keeping. Implications for future theory development, research and practical implications were provided as was a suggestion for the development of multidisciplinary research efforts conducted within the context of Centers for the study and application of adherence behaviors. ^

Identification and evaluation of candidate genes for inherited retinal -degenerative diseases

Although more than 100 genes associated with inherited retinal disease have been mapped to chromosomal locations, less than half of these genes have been cloned. This text includes identification and evaluation of candidate genes for three autosomal dominant forms of inherited retinal degeneration: atypical vitelliform macular dystrophy (VMD1), cone-rod dystrophy (CORD), and retinitis pigmentosa (RP). ^ VMD1 is a disorder characterized by complete penetrance but extremely variable expressivity, and includes macular or peripheral retinal lesions and peripappilary abnormalitites. In 1984, linkage was reported between VMD1 and soluble glutamate-pyruvate transaminase GPT); however, placement of GPT to 8q24 on linkage maps had been debated, and VMD1 did not show linkage to microsatellite markers in that region. This study excluded linkage between the loci by cloning GPT, identifying the nucleotide substitution associated with the GPT sozymes, and by assaying VMD1 family samples with an RFLP designed to detect the substitution. In addition, linkage of VMD1 to the known dominant macular degeneration loci was excluded. ^ CORD is characterized by early onset of color-vision deficiency, and decreased visual acuity, However, this retinal degeneration progresses to no light perception, severe macular lesion, and “bone-spicule” accumulations in the peripheral retina. In this study, the disorder in a large Texan family was mapped to the CORD2 locus of 19q13, and a mutation in the retina/pineal-specific cone-rod homeobox gene (CRX) was identified as the disease cause. In addition, mutations in CRX were associated with significantly different retinal disease phenotypes, including retinitis pigmentosa and Leber congenital amaurosis. ^ Many of the mutations leading to inherited retinal disorders have been identified in genes like CRX, which are expressed predominantly in the retina and pineal gland. Therefore, a combination of database analysis and laboratory investigation was used to identify 26 novel retina/pineal-specific expressed sequence tag (EST) clusters as candidate genes for inherited retinal disorders. Eight of these genes were mapped into the candidate regions of inherited retinal degeneration loci. ^ Two of the eight clusters mapped into the retinitis pigmentosa RP13 candidate region of 17p13, and were both determined to represent a single gene that is highly expressed in photoreceptors. This gene, the Ah receptor-interacting like protein-1 (AIPL1), was cloned, characterized, and screened for mutations in RP13 patient DNA samples. ^

OJS Implementation and development of the Scientific Journals Site of the School of Humanities and Education Sciences at the Universidad Nacional de La Plata

Este trabajo tiene como objetivo describir la experiencia de implementación y desarrollo del Portal de revistas de la Facultad de Humanidades y Ciencias de Educación de la Universidad Nacional de La Plata a fin de que pueda ser aprovechada por todos aquellos que emprendan iniciativas de características similares. Para ello, se realiza en primer lugar un repaso por la trayectoria de la Facultad respecto a la edición de revistas científicas y la labor bibliotecaria para contribuir a su visualización. En segundo orden, se exponen las tareas llevadas adelante por la Prosecretaría de Gestión Editorial y Difusión (PGEyD) de la Facultad para concretar la puesta en marcha del portal. Se hace especial referencia a la personalización del software, a la metodología utilizada para la carga masiva de información en el sistema (usuarios y números retrospectivos) y a los procedimientos que permiten la inclusión en repositorio institucional y en el catálogo web de todos los contenidos del portal de manera semi-automática. Luego, se hace alusión al trabajo que se está realizando en relación al soporte y a la capacitación de los editores. Se exponen, después, los resultados conseguidos hasta el momento en un año de trabajo: creación de 10 revistas, migración de 4 títulos completos e inclusión del 25de las contribuciones publicadas en las revistas editadas por la FaHCE. A modo de cierre se enuncian una serie de desafíos que la Prosecretaría se ha propuesto para mejorar el Portal y optimizar los flujos de trabajo intra e interinstitucionales

OJS Implementation and development of the Scientific Journals Site of the School of Humanities and Education Sciences at the Universidad Nacional de La Plata

Este trabajo tiene como objetivo describir la experiencia de implementación y desarrollo del Portal de revistas de la Facultad de Humanidades y Ciencias de Educación de la Universidad Nacional de La Plata a fin de que pueda ser aprovechada por todos aquellos que emprendan iniciativas de características similares. Para ello, se realiza en primer lugar un repaso por la trayectoria de la Facultad respecto a la edición de revistas científicas y la labor bibliotecaria para contribuir a su visualización. En segundo orden, se exponen las tareas llevadas adelante por la Prosecretaría de Gestión Editorial y Difusión (PGEyD) de la Facultad para concretar la puesta en marcha del portal. Se hace especial referencia a la personalización del software, a la metodología utilizada para la carga masiva de información en el sistema (usuarios y números retrospectivos) y a los procedimientos que permiten la inclusión en repositorio institucional y en el catálogo web de todos los contenidos del portal de manera semi-automática. Luego, se hace alusión al trabajo que se está realizando en relación al soporte y a la capacitación de los editores. Se exponen, después, los resultados conseguidos hasta el momento en un año de trabajo: creación de 10 revistas, migración de 4 títulos completos e inclusión del 25de las contribuciones publicadas en las revistas editadas por la FaHCE. A modo de cierre se enuncian una serie de desafíos que la Prosecretaría se ha propuesto para mejorar el Portal y optimizar los flujos de trabajo intra e interinstitucionales

OJS Implementation and development of the Scientific Journals Site of the School of Humanities and Education Sciences at the Universidad Nacional de La Plata

Este trabajo tiene como objetivo describir la experiencia de implementación y desarrollo del Portal de revistas de la Facultad de Humanidades y Ciencias de Educación de la Universidad Nacional de La Plata a fin de que pueda ser aprovechada por todos aquellos que emprendan iniciativas de características similares. Para ello, se realiza en primer lugar un repaso por la trayectoria de la Facultad respecto a la edición de revistas científicas y la labor bibliotecaria para contribuir a su visualización. En segundo orden, se exponen las tareas llevadas adelante por la Prosecretaría de Gestión Editorial y Difusión (PGEyD) de la Facultad para concretar la puesta en marcha del portal. Se hace especial referencia a la personalización del software, a la metodología utilizada para la carga masiva de información en el sistema (usuarios y números retrospectivos) y a los procedimientos que permiten la inclusión en repositorio institucional y en el catálogo web de todos los contenidos del portal de manera semi-automática. Luego, se hace alusión al trabajo que se está realizando en relación al soporte y a la capacitación de los editores. Se exponen, después, los resultados conseguidos hasta el momento en un año de trabajo: creación de 10 revistas, migración de 4 títulos completos e inclusión del 25de las contribuciones publicadas en las revistas editadas por la FaHCE. A modo de cierre se enuncian una serie de desafíos que la Prosecretaría se ha propuesto para mejorar el Portal y optimizar los flujos de trabajo intra e interinstitucionales

The Regional Development Policy of Thailand and Its Economic Cooperation with Neighboring Countries

Thailand has recently strengthened its economic policy toward its neighboring countries in coordination with domestic regional development. It is widely recognized that economic cooperation with neighboring countries is essential in preventing the inflow of illegal labor and effectively utilizing labor and resources through the relocation of production bases. This direction is strengthened by elaborating the GMS-EC and the ECS (Economic Cooperation Strategy). In addition, economic dependency of the neighboring countries on Thailand is generally high. In this report, firstly, Thai regional development policy will be made clear in relation to its economic policy toward neighboring countries as well as the status quo of the industrial estates. Secondly, Thai policy toward the neighboring countries is examined referring to the concept of wide-ranging economic zones, regional economic cooperation and special border economic zones. Thirdly, the paper will discuss how closely the economies between Thailand and the neighboring countries are related through trade and investment. Lastly, some implications on Japan's economic cooperation will also be explored.

Analytical study and evaluation results of power optimizers for distributed power conditioning in PV arrays

The use of modular or ‘micro’ maximum power point tracking (MPPT) converters at module level in series association, commercially known as “power optimizers”, allows the individual adaptation of each panel to the load, solving part of the problems related to partial shadows and different tilt and/or orientation angles of the photovoltaic (PV) modules. This is particularly relevant in building integrated PV systems. This paper presents useful behavioural analytical studies of cascade MPPT converters and evaluation test results of a prototype developed under a Spanish national research project. On the one hand, this work focuses on the development of new useful expressions which can be used to identify the behaviour of individual MPPT converters applied to each module and connected in series, in a typical grid-connected PV system. On the other hand, a novel characterization method of MPPT converters is developed, and experimental results of the prototype are obtained: when individual partial shading is applied, and they are connected in a typical grid connected PV array

Sharing Human-Generated Observations by Integrating HMI and the Semantic Sensor Web

Current “Internet of Things” concepts point to a future where connected objects gather meaningful information about their environment and share it with other objects and people. In particular, objects embedding Human Machine Interaction (HMI), such as mobile devices and, increasingly, connected vehicles, home appliances, urban interactive infrastructures, etc., may not only be conceived as sources of sensor information, but, through interaction with their users, they can also produce highly valuable context-aware human-generated observations. We believe that the great promise offered by combining and sharing all of the different sources of information available can be realized through the integration of HMI and Semantic Sensor Web technologies. This paper presents a technological framework that harmonizes two of the most influential HMI and Sensor Web initiatives: the W3C’s Multimodal Architecture and Interfaces (MMI) and the Open Geospatial Consortium (OGC) Sensor Web Enablement (SWE) with its semantic extension, respectively. Although the proposed framework is general enough to be applied in a variety of connected objects integrating HMI, a particular development is presented for a connected car scenario where drivers’ observations about the traffic or their environment are shared across the Semantic Sensor Web. For implementation and evaluation purposes an on-board OSGi (Open Services Gateway Initiative) architecture was built, integrating several available HMI, Sensor Web and Semantic Web technologies. A technical performance test and a conceptual validation of the scenario with potential users are reported, with results suggesting the approach is sound

Design and evaluation of acceleration strategies for speeding up the development of dialog applications

In this paper, we describe a complete development platform that features different innovative acceleration strategies, not included in any other current platform, that simplify and speed up the definition of the different elements required to design a spoken dialog service. The proposed accelerations are mainly based on using the information from the backend database schema and contents, as well as cumulative information produced throughout the different steps in the design. Thanks to these accelerations, the interaction between the designer and the platform is improved, and in most cases the design is reduced to simple confirmations of the “proposals” that the platform dynamically provides at each step. In addition, the platform provides several other accelerations such as configurable templates that can be used to define the different tasks in the service or the dialogs to obtain or show information to the user, automatic proposals for the best way to request slot contents from the user (i.e. using mixed-initiative forms or directed forms), an assistant that offers the set of more probable actions required to complete the definition of the different tasks in the application, or another assistant for solving specific modality details such as confirmations of user answers or how to present them the lists of retrieved results after querying the backend database. Additionally, the platform also allows the creation of speech grammars and prompts, database access functions, and the possibility of using mixed initiative and over-answering dialogs. In the paper we also describe in detail each assistant in the platform, emphasizing the different kind of methodologies followed to facilitate the design process at each one. Finally, we describe the results obtained in both a subjective and an objective evaluation with different designers that confirm the viability, usefulness, and functionality of the proposed accelerations. Thanks to the accelerations, the design time is reduced in more than 56% and the number of keystrokes by 84%.

Clean Coal Technologies Scenario and Evaluation of Present CO2 Dwindling Initiatives to Approach Zero Emission Power Stations By Coal Combustion. Deployment Situation and Evaluation Study

In the present uncertain global context of reaching an equal social stability and steady thriving economy, power demand expected to grow and global electricity generation could nearly double from 2005 to 2030. Fossil fuels will remain a significant contribution on this energy mix up to 2050, with an expected part of around 70% of global and ca. 60% of European electricity generation. Coal will remain a key player. Hence, a direct effect on the considered CO2 emissions business-as-usual scenario is expected, forecasting three times the present CO2 concentration values up to 1,200ppm by the end of this century. Kyoto protocol was the first approach to take global responsibility onto CO2 emissions monitoring and cap targets by 2012 with reference to 1990. Some of principal CO2emitters did not ratify the reduction targets. Although USA and China spur are taking its own actions and parallel reduction measures. More efficient combustion processes comprising less fuel consuming, a significant contribution from the electricity generation sector to a CO2 dwindling concentration levels, might not be sufficient. Carbon Capture and Storage (CCS) technologies have started to gain more importance from the beginning of the decade, with research and funds coming out to drive its come in useful. After first researching projects and initial scale testing, three principal capture processes came out available today with first figures showing up to 90% CO2 removal by its standard applications in coal fired power stations. Regarding last part of CO2 reduction chain, two options could be considered worthy, reusing (EOR & EGR) and storage. The study evaluates the state of the CO2 capture technology development, availability and investment cost of the different technologies, with few operation cost analysis possible at the time. Main findings and the abatement potential for coal applications are presented. DOE, NETL, MIT, European universities and research institutions, key technology enterprises and utilities, and key technology suppliers are the main sources of this study. A vision of the technology deployment is presented.