Preparation and characterization of mesoporous Ni/Zr-laponite for the catalytic deoxygenation of vegetable oils into liquid hydrocarbons

The deoxygenation of vegetable oils was studied over a Ni/Zr-laponite catalyst in various nickel loading composition. Stearic acid has been used as a model compounds. The liquid and gas products were analyzed using gas chromatograph equipped with thermal conductivity detector and flame ionization detector. From product distribution it was determined the effect of catalyst composition on reaction conditions

Upgrading fast pyrolysis liquids:blends of biodiesel and pyrolysis oil

Fast pyrolysis liquid or bio-oil has been used in engines with limited success. It requires a pilot fuel and/or an additive for successful combustion and there are problems with materials and liquid properties. It is immiscible with all conventional hydrocarbon fuels. Biodiesel, a product of esterification of vegetable oil with an alcohol, is widely used as a renewable liquid fuel as an additive to diesel at up to 20%. There are however limits to its use in conventional engines due to poor low temperature performance and variability in quality from a variety of vegetable oil qualities and variety of esterification processes. Within the European Project Bioliquids-CHP - a joint project between the European Commission and Russia - a study was undertaken to develop small scale CHP units based on engines and microturbines fuelled with bioliquids from fast pyrolysis and methyl esters of vegetable oil. Blends of bio-oil and biodiesel were evaluated and tested to overcome some of the disadvantages of using either fuel by itself. An alcohol was used as the co-solvent in the form of ethanol, 1-butanol or 2-propanol. Visual inspection of the blend homogeneity after 48 h was used as an indicator of the product stability and the results were plotted in a three phase chart for each alcohol used. An accelerated stability test was performed on selected samples in order to predict its long term stability. We concluded that the type and quantity of alcohol is critical for the blend formation and stability. Using 1-butanol gave the widest selection of stable blends, followed by blends with 2-propanol and finally ethanol, thus 1-butanol blends accepted the largest proportion of bio-oil in the mixture. © 2013 Elsevier Ltd. All rights reserved.

Production of Polyhydroxyalkanoates by Pseudomonas mendocina using vegetable oils and their characterisation

Synthesis of Polyhydroxyalkanoates (PHAs) by Pseudomonas mendocina, using different vegetable oils such as, coconut oil, groundnut oil, corn oil and olive oil, as the sole carbon source was investigated for the first time. The PHA yield obtained was compared with that obtained during the production of PHAs using sodium octanoate as the sole carbon source. The fermentation profiles at shaken flask and bioreactor levels revealed that vegetable oils supported the growth of Pseudomonas mendocina and PHA accumulation in this organism. Moreover, when vegetable oil (coconut oil) was used as the sole carbon source, fermentation profiles showed better growth and polymer production as compared to conditions when sodium octanoate was used as the carbon source. In addition, comparison of PHA accumulation at shaken flask and fermenter level confirmed the higher PHA yield at shaken flask level production. The highest cell mass found using sodium octanoate was 1.8 g/L, whereas cell mass as high as 5.1 g/L was observed when coconut oil was used as the feedstock at flask level production. Moreover, the maximum PHA yield of 60.5% dry cell weight (dcw) was achieved at shaken flask level using coconut oil as compared to the PHA yield of 35.1% dcw obtained using sodium octanoate as the sole carbon source. Characterisations of the chemical, physical, mechanical, surface and biocompatibility properties of the polymers produced have been carried out by performing different analyses as described in the second chapter of this study. Chemical analysis using GC and FTIR investigations showed medium chain length (MCL) PHA production in all conditions. GC-MS analysis revealed a unique terpolymer production, containing 3-hydroxyoctanoic acid, 3-hydroxydecanoic acid and 3-hydroxydodecanoic acid when coconut oil, groundnut oil, olive oil, and corn oil were used as the carbon source. Whereas production of the homopolymer containing 3-hydroxyoctanoic acid was observed when sodium octanoate was used as the carbon source. MCL-PHAs produced in this study using sodium octanoate, coconut oil, and olive oil exhibited melting transitions, indicating that each of the PHA was crystalline or semi-crystalline polymer. In contrast, the thermal properties of PHAs produced from groundnut and corn oils showed no melting transition, indicating that they were completely amorphous or semi-crystalline, which was also confirmed by the X-Ray Diffraction (XRD) results obtained in this study. Mechanical analysis of the polymers produced showed higher stiffness of the polymer produced from coconut oil than the polymer from sodium octanoate. Surface characterisation of the polymers using Scanning Electron Microscopy (SEM) revealed a rough surface topography and surface contact angle measurement revealed their hydrophobic nature. Moreover, to investigate the potential applicability of the produced polymers as the scaffold materials for dental pulp regeneration, multipotent human Mesenchymal stem cells (hMSCs) were cultured onto the polymer films. Results indicated that these polymers are not cytotoxic towards the hMSCs and could support their attachment and proliferation. Highest cell growth was observed on the polymer samples produced from corn oil, followed by the polymer produced using coconut oil. In conclusion, this work established, for the first time, that vegetable oils are a good economical source of carbon for production of MCL-PHA copolymers effectively by Pseudomonas mendocina. Moreover, biocompatibility studies suggest that the produced polymers may have potential for dental tissue engineering application.

Estimation of biodiesel properties from chemical composition – An artificial neural network (ANN) approach

Biodiesel, produced from renewable feedstock represents a more sustainable source of energy and will therefore play a significant role in providing the energy requirements for transportation in the near future. Chemically, all biodiesels are fatty acid methyl esters (FAME), produced from raw vegetable oil and animal fat. However, clear differences in chemical structure are apparent from one feedstock to the next in terms of chain length, degree of unsaturation, number of double bonds and double bond configuration-which all determine the fuel properties of biodiesel. In this study, prediction models were developed to estimate kinematic viscosity of biodiesel using an Artificial Neural Network (ANN) modelling technique. While developing the model, 27 parameters based on chemical composition commonly found in biodiesel were used as the input variables and kinematic viscosity of biodiesel was used as output variable. Necessary data to develop and simulate the network were collected from more than 120 published peer reviewed papers. The Neural Networks Toolbox of MatLab R2012a software was used to train, validate and simulate the ANN model on a personal computer. The network architecture and learning algorithm were optimised following a trial and error method to obtain the best prediction of the kinematic viscosity. The predictive performance of the model was determined by calculating the coefficient of determination (R2), root mean squared (RMS) and maximum average error percentage (MAEP) between predicted and experimental results. This study found high predictive accuracy of the ANN in predicting fuel properties of biodiesel and has demonstrated the ability of the ANN model to find a meaningful relationship between biodiesel chemical composition and fuel properties. Therefore the model developed in this study can be a useful tool to accurately predict biodiesel fuel properties instead of undertaking costly and time consuming experimental tests.

Management of mould mite Tyrophagus putrescentiae (Schrank) (Acarina: Acaridae): A case study in stored animal feed

An integrated pest management (IPM) strategy was developed to manage infestations of mould mite Tyrophagus putrescentiae (Schrank) in stored animal feed, due to the increasing importance of these mites as pests of feed processing and storage facilities in Australia. This strategy involved several aspects such as limiting the moisture content of the processed feed to 12%, admixing vegetable oil to some feed (2% w/w), strict hygiene practice in and around the processing and storage facility, and rejection of infested grain at the receiving point. Additionally, seven contact insecticides and the fumigant phosphine were evaluated for their effectiveness against the mould mite to assess their potential integration into the IPM strategy. Among them, pyrethrin synergised with piperonyl butoxide, the insect growth regulator s-methoprene and a newly developed bacterium-based material spinosad controlled the mites. Moreover, the fumigant phosphine at 1 mg/litre over a six days exposure period also controlled these mites. So far, the IPM strategy, without any involvement of insecticides or fumigant has resulted in a complete eradication of the mite population in this particular case of stored animal feed.

Physio-chemical assessment of beauty leaf (Calophyllum inophyllum) as second-generation biodiesel feedstock

Recently, second-generation (non-vegetable oil) feedstocks for biodiesel production are receiving significant attention due to the cost and social effects connected with utilising food products for the production of energy products. The Beauty leaf tree (Calophyllum inophyllum) is a potential source of non-edible oil for producing second-generation biodiesel because of its suitability for production in an extensive variety of atmospheric condition, easy cultivation, high fruit production rate, and the high oil content in the seed. In this study, oil was extracted from Beauty leaf tree seeds through three different oil extraction methods. The important physical and chemical properties of these extracted Beauty leaf oils were experimentally analysed and compared with other commercially available vegetable oils. Biodiesel was produced using a two-stage esterification process combining of an acid catalysed pre-esterification process and an alkali catalysed transesterification process. Fatty acid methyl ester (FAME) profiles and important physicochemical properties were experimentally measured and estimated using equations based on the FAME analysis. The quality of Beauty leaf biodiesels was assessed and compared with commercially available biodiesels through multivariate data analysis using PROMETHEE-GAIA software. The results show that mechanical extraction using a screw press produces oil at a low cost, however, results in low oil yields compared with chemical oil extraction. High pressure and temperature in the extraction process increase oil extraction performance. On the contrary, this process increases the free fatty acid content in the oil. A clear difference was found in the physical properties of Beauty leaf oils, which eventually affected the oil to biodiesel conversion process. However, Beauty leaf oils methyl esters (biodiesel) were very consistent physicochemical properties and able to meet almost all indicators of biodiesel standards. Overall this study found that Beauty leaf is a suitable feedstock for producing second-generation biodiesel in commercial scale. Therefore, the findings of this study are expected to serve as the basis for further development of Beauty leaf as a feedstock for industrial scale second-generation biodiesel production.

Bioavailability aspects of hydrophobic contaminant degradation in soils

This thesis concentrates on bioavailability of organic soil contaminants in the context of bioremediation of soil contaminated with volatile or non-volatile hydrophobic pollutants. Bioavailability and biodegradation was studied from four viewpoints: (i) Improvement of bioavailability and biodegradation of volatile hydrocarbons in contained bioremediation systems at laboratory - and pilot-scale. (ii) Improvement of bioavailability of non-volatile, hydrophobic compounds in such systems. (iii) Biodegradation of a non-volatile hydrophobic compound in soil organic matter in microcosms. (iiii) Bioavailability of nitrogen in an open, full-scale bioremediation system. It was demonstrated that volatility of organic compounds can be controlled by amending the soil with adsorbents. The sorbed hydrocarbons were shown to be available to soil microbiota. As the result, biodegradation of the volatile hydrocarbons was greatly favored at the expense of volatilization. PAH compounds were shown to be mobilized and their bioavailability improved by a hydrophobic, non-toxic additive, vegetable oil. Bioavailability of the PAHs was recorded as an increased toxicity of the soil. In spite of the increased bioavailability, biodegradation of the PAHs decreased. In microcosms simulating boreal forest organic surface soil, PAH-compound (pyrene) was shown to be removed from soil biologically. Therefore hydrophobicity of the substrate does not necessarily mean low availability and biodegradation in organic soil. Finally, in this thesis it was demonstrated that an unsuitable source of nitrogen or its overdose resulted in wasteful spending of this nutrient and even harmful effects on soil microbes. Such events may inhibit rather than promote the bioremediation process in soil.

Experimental Studies on High-Pressure Spray Structure of Biofuels

The high-pressure spray characteristics of biofuels, specifically, Pongamia oil and its blends with diesel are studied for various gas pressures. Two single-hole solenoid injectors with nozzle diameters of 200 and 260 mu m are used along with a high-pressure common-rail direct-injection system to inject fuel into a high-pressure spray visualization chamber. The spray structure is characterized using a high-speed laser-based shadowgraphy technique. The spray structure of Pongamia oil revealed the presence of an intact liquid core at low gas pressure. At high gas pressures, the spray atomization of the Pongamia oil showed marked improvement. The spray tip penetration of Pongamia oil and its blends with diesel is higher compared to that of diesel for all test conditions. The spray cone angle of Pongamia oil and 50% Pongamia oil blend with diesel is lower as compared to that of diesel. Both these observations are attributed to the presence of large droplets carrying higher momentum in oil and blend. The droplet size is measured at an injection pressure of 1000 bar and gas pressure of 30 bar at 25 mm below the nozzle tip using the particle/droplet image.analysis (PDIA) method. The droplet size measurements have shown that the Sauter mean diameter (SMD) in the spray core of Pongamia oil is more than twice that of diesel. The spray tip penetration of the 20% blend of Pongamia with diesel (P20) is similar to that of diesel but the SMD is 50% higher. Based on experimental data, appropriate spray tip penetration correlation is proposed for the vegetable oil fuels such as Pongamia.

Control of insect infestation in smoked West African sardines Sardinella maderensis 'Sawa' using actellic 50 EC solution

Fish which has been cured or are in the process of being cured by traditional methods are usually infested by insects, posing a real problem to traders and processors, especially in Nigeria. The effects of 0.03% actellic 50 EC solution and vegetable oil on insect infestion were studied using West African sardines, Sardinella maderensis. Actellic solution was more effective in combating insect infestation than vegetable oil. Appearance and perceived smoked fish flavour of fish treated with Actellic and vegetable oil differed (P<0.05), while taste was unaffected by treatment. Actellic 50 EC solution though effective, could be subject to abuse

Síntese e caracterização de biodiesel obtido via catálises homogênea e heterogênea de óleo extraído de sementes de Helianthus annuus

O biodiesel é definido como um mono alquil éster de ácidos graxos de cadeia longa derivado de fontes renováveis tais como óleos vegetais e gorduras animais. Sua importância esta associada ao uso como um combustível alternativo para motores do ciclo Diesel podendo ser utilizado puro ou em misturas com o diesel representando economia de petróleo e menor poluição ambiental. Em geral é obtido por meio da reação de transesterificação na qual os triacilgliceróis, principais constituintes dos óleos e gorduras reagem com álcool, em presença de um catalisador ácido ou básico, produzindo ésteres de ácidos graxos e glicerol. A transesterificação pode ser conduzida por catálise homogênea ou heterogênea. O grande desafio da indústria é otimizar o processo a fim de alcançar um produto e uma rota de produção tecnologicamente eficiente e ambientalmente correta. O objetivo desta pesquisa foi estudar a síntese do biodiesel utilizando o processo de transesterificação do óleo de girassol por catálises homogênea e heterogênea. Foram realizadas reações de transesterificação via rotas metílica e etílica, empregando como catalisador homogêneo alcóxido de potássio e como catalisador heterogêneo a resina comercial de troca iônica Amberlyst 26

Avaliação da acidez de bio-óleos obtidos pela pirólise de óleos vegetais pós-consumo

O descarte irregular do óleo vegetal pós-consumo diretamente na rede de esgoto vem causando grandes problemas para o meio ambiente. Atualmente, essa problemática tem se intensificado devido ao aumento de produção e consumo destes óleos, o que por conseqüência aumenta o despejo desordenado. No presente estudo foi realizada a obtenção do bio-óleo a partir da pirólise térmica em atmosfera de nitrogênio, a 400C, por 20 minutos, do óleo vegetal pós-consumo, provenientes das seguintes oleoginosas: soja, milho, girassol e canola. As pirólises não-catalíticas apresentaram uma geração média entre 40 e 50% de um bio-óleo, de elevado índice de acidez, 81,8 mg NaOH/g. Na pirólise catalítica, a argila ácida K10 foi o catalisador que apresentou melhor eficácia para geração de um bio-óleo de menor índice de acidez. A concentração ótima do catalisador foi de 5%(m/m), gerando 482 % de um bio-óleo com índice de acidez de 43,8 mg NaOH/g. A caracterização dos líquidos pirolíticos obtidos foi realizada através da técnica de espectrofotometria na região do infravermelho (FTIR) e cromatografia em fase gasosa acoplada a espectrômetro de massas (CG/EM) que monstraram que a trioleína, o triglicerídeo do ácido oléico, foi craqueado, gerando o hexadecanoato de octadecila e o oleato de eicosila, ésteres do respectivo ácido graxo

Canning of edible oyster

Edible oyster, Crassostrea cucullata, was canned in different filling media viz, its own nector, brine and double refined vegetable oil, to study the effect of each, on the flavour and general quality characteristics of the final product. A method was worked out to produce a canned product, of appealing flavour form oysters after light smoking. The paper reports the results of these studies.

Selective Hydrogenation of Acetylene over Pd-Boron Catalysts: A Density Functional Theory Study

Boron-modified Pd catalysts have shown excellent performance for the selective hydrogenation of alkynes experimentally. In the current work, we investigated the hydrogenation of acetylene on boron-modified Pd(111) and Pd(211) surfaces, utilizing density functional theory calculations. The activity of acetylene hydrogenation has been studied by estimating the effective barrier of the whole process. The selectivity of ethylene formation is investigated from a comparison between the desorption and the hydrogenation of ethylene as well as comparison between the ethylene and the 1,3-butadiene formation. Formation of subsurface carbon and hydrogen on both boron-modified Pd(111) and Pd(211) surfaces has also been evaluated, since these have been reported to affect both the activity and the selectivity of acetylene hydrogenation to produce ethylene on Pd surfaces. Our results provide some important insights into the Pd B catalysts for selective hydrogenation of acetylene and also for more complex hydrogenation systems, such as stereoselective hydrogenation of longer chain alkynes and selective hydrogenation of vegetable oil.

Generating Data Augmented Spectroscopic Data For Performance Enhancement

The application of chemometrics in food science has revolutionized the field by allowing the creation of models able to automate a broad range of applications such as food authenticity and food fraud detection. In order to create effective and general models able to address the complexity of real life problems, a vast amount of varied training samples are required. Training dataset has to cover all possible types of sample and instrument variability. However, acquiring a varied amount of samples is a time consuming and costly process, in which collecting samples representative of the real world variation is not always possible, specially in some application fields. To address this problem, a novel framework for the application of data augmentation techniques to spectroscopic data has been designed and implemented. This is a carefully designed pipeline of four complementary and independent blocks which can be finely tuned depending on the desired variance for enhancing model's robustness: a) blending spectra, b) changing baseline, c) shifting along x axis, and d) adding random noise.
This novel data augmentation solution has been tested in order to obtain highly efficient generalised classification model based on spectroscopic data. Fourier transform mid-infrared (FT-IR) spectroscopic data of eleven pure vegetable oils (106 admixtures) for the rapid identification of vegetable oil species in mixtures of oils have been used as a case study to demonstrate the influence of this pioneering approach in chemometrics, obtaining a 10% improvement in classification which is crucial in some applications of food adulteration.

Chromatographic analysis and comparison of chemical composition of the samples between olive oils in Europe and some chinese oils

Dissertação de mest., Qualidade em Análises, Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2013