Low cycle fatigue properties of CLAM steel at 823 K

China Low Activation Martensitic (CLAM) steel is considered to be the main candidate material for the first wall components of future fusion reactors in China. In this paper, the low cycle fatigue (LCF) behavior of CLAM steel is studied under fully reversed tension–compression loading at 823 K in air. Total strain amplitude was controlled from 0.14% to 1.8% with a constant strain rate of 2.4×10−3 s−1. The corresponding plastic strain amplitude ranged from 0.023% to 1.613%. The CLAM steel displayed continuous softening to failure at 823 K. The relationship between strain, stress and fatigue life was obtained using the parameters obtained from fatigue tests. The LCF properties of CLAM steel at 823 K followed Coffin–Manson relationship. Furthermore, irregular serration was observed on the stress–strain hysteresis loops of CLAM steel tested with the total strain amplitude of 0.45–1.8%, which was attributed to the dynamic strain aging (DSA) effect. During continuous cyclic deformation, the microstructure and precipitate distribution of CLAM steel changed gradually. Many tempered martensitic laths were decomposed into subgrains, and the size and number of M23C6 carbide and MX carbonitride precipitates decreased with the increase of total strain amplitude. The response cyclic stress promoted the recovery of martensitic lath, while the thermal activation mainly played an important role on the growth of precipitates in CLAM steel at 823 K. In order to have a better understanding of high-temperature LCF behavior, the potential mechanisms controlling stress–strain response, DSA phenomenon and microstructure changes have also been evaluated.

Low cycle fatigue properties of CLAM steel at room temperature

The low cycle fatigue (LCF) properties and the fracture behavior of China Low Activation Martensitic (CLAM) steel have been studied over a range of total strain amplitudes from 0.2 to 2.0%. The specimens were cycled using tension-compression loading under total strain amplitude control. The CLAM steel displayed initial hardening followed by continuous softening to failure at room temperature in air. The relationship between strain and fatigue life was predicted using the parameters obtained from fatigue test. The factors effecting on low cycle fatigue of CLAM steel consisted of initial state of matrix dislocation arrangement, magnitude of cyclic stress, magnitude of total strain amplitude and microstructure. The potential mechanisms controlling the stress response, cyclic strain resistance and low cycle fatigue life have been evaluated.

A Numerical Study of the Flow Fields in a Highly Off-Design Variable Geometry Turbine

Conventionally, radial turbines have almost exclusively used radially fibred blades. While issues of mechanical integrity are paramount, there may be opportunities for improving turbine efficiency through a 3D blade design without exceeding mechanical limits. Off-design performance and understanding of the secondary flow structures now plays a vital role in the design decisions made for automotive turbocharger turbines. Of particular interest is extracting more energy at high pressure ratios and lower rotational speeds. Operating in this region means the rotor will experience high values of positive incidence at the inlet. A CFD analysis has been carried out on a scaled automotive turbine utilizing a swing vane stator system. To date no open literature exists on the flow structures present in a standard VGT system. Investigations were carried out on a 90 mm diameter rotor with the stator vane at the maximum, minimum and 25% mass flow rate positions. In addition stator vane endwall clearance existed at the hub side. From investigation of the internal flow fields of the baseline rotor, a number of areas that could be optimized in the future with three dimensional blading were identified. The blade loading and tip leakage flow near inlet play a significant role in the flow development further downstream at all stator vane positions. It was found that tip leakage flow and flow separation at off-design conditions could be reduced by employing back swept blading and redistributing the blade loading. This could potentially reduce the extent of the secondary flow structures found in the present study.

Mental Toughness Moderates Social Loafing in Cycle Time-Trial Performance

Purpose: The purpose of this study was to determine if mental toughness moderated the occurrence of social loafing in cycle time-trial performance. Method: Twenty-seven men (Mage = 17.7 years, SD = 0.6) completed the Sport Mental Toughness Questionnaire prior to completing a 1-min cycling trial under 2 conditions: once with individual performance identified, and once in a group with individual performance not identified. Using a median split of the mental toughness index, participants were divided into high and low mental toughness groups. Cycling distance was compared using a 2 (trial) × 2 (high–low mental toughness) analysis of variance. We hypothesized that mentally tough participants would perform equally well under both conditions (i.e., no indication of social loafing) compared with low mentally tough participants, who would perform less well when their individual performance was not identifiable (i.e., demonstrating the anticipated social loafing effect). Results: The high mental toughness group demonstrated consistent performance across both conditions, while the low mental toughness group reduced their effort in the non-individually identifiable team condition. Conclusions: The results confirm that (a) clearly identifying individual effort/performance is an important situational variable that may impact team performance and (b) higher perceived mental toughness has the ability to negate the tendency to loaf.

Credit cycle identification: A Markov-switching application

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Finance from the NOVA – School of Business and Economics

Les pratiques d’enseignement de la littératie d’enseignants experts du premier cycle du primaire et la place accordée à la différenciation pédagogique

La présente recherche vise à décrire les pratiques d’enseignement de la littératie au premier cycle du primaire en contexte montréalais d’enseignants considérés experts. Plus précisément, les trois objectifs de recherche consistent à décrire les pratiques d’enseignement de la langue écrite au premier cycle du primaire en contexte montréalais privilégiées par certains enseignants considérés experts (N=6) (objectif 1); à décrire les différentes formes de différenciation pédagogique privilégiées pour l’enseignement de la lecture et de l’écriture en contexte montréalais de certains enseignants considérés experts afin de répondre aux besoins variés de tous leurs élèves (objectif 2) et à étudier les liens possibles entre les pratiques d’enseignement de la langue écrite d’enseignants considérés experts et la progression de leurs élèves (N=100) du premier cycle du primaire en contexte montréalais, au regard de leur connaissance des correspondances phonographiques et de la norme orthographique (objectif 3). Afin de répondre aux objectifs, deux entretiens ont été menés auprès des enseignantes, de même que deux observations en classe, une à l’automne et une au printemps. Pour leur part, les élèves ont été soumis à deux tâches d’écriture à deux reprises durant l’année (une tâche de production de mots et une tâche de production de texte) permettant de mesurer leur progression en cours d’année relativement à leurs connaissances des correspondances phonographiques et de la norme orthographique. Nos résultats nous ont permis de recueillir des pratiques très diversifiées et conduites avec une fréquence fort différente d’une enseignante à l’autre. La densité des contenus abordés en classe diffère également beaucoup entre les enseignantes. En lien avec le modèle du multi-agenda de Bucheton et Soulé (2009), les cinq composantes constituant la matrice de l’activité de l’enseignant se retrouvent dans toutes les classes, mais ces préoccupations n’occupent pas toutes la même place dans les pratiques des enseignantes de la recherche. Nos résultats indiquent aussi que toutes les enseignantes différencient leur enseignement, mais de façon variable. Il semble que ce soit la différenciation des processus, des contenus et des structures qui soit la plus aisée à mettre en place en classe. En lien avec notre adaptation du modèle de différenciation pédagogique de Caron (2008), il semble que ce soit la diversification et l’offre de choix qui sont mobilisées le plus fréquemment. Les mesures d’adaptation sont rarement mises en avant dans les pratiques de classe, tandis que les mesures d’individualisation n’ont pas été constatées. En ce qui a trait aux résultats des élèves aux tâches en écriture, nos résultats indiquent que deux groupes se démarquent parmi les six. En effet, c’est dans ces deux classes que la plus forte progression est constatée. Les pratiques des enseignantes de ces deux classes sont très diversifiées et elles sont les seules à mettre en avant dans leurs pratiques tous les dispositifs dont il est question en entretiens. De plus, les contenus enseignés sont denses, ce qui est réputé pour caractériser les pratiques des enseignants efficaces (Hall, 2003). De même, ces deux enseignantes offrent un étayage de grande qualité à leurs élèves et maîtrisent parfaitement le pilotage des tâches. La présente recherche peut servir à apporter un éclairage nouveau sur les pratiques de littératie des enseignants considérés experts afin de mieux comprendre leurs pratiques, de même que la place qu’ils accordent à la différenciation pédagogique.

Inexpensive footwear decreases joint loading in elderly women with knee osteoarthritis

Recent literature has highlighted that the flexibility of walking barefoot reduces overload in individuals with knee osteoarthritis (OA). As such, the aim of this study was to evaluate the effects of inexpensive, flexible, non-heeled footwear (Moleca (R)) as compared with a modern heeled shoes and walking barefoot on the knee adduction moment (KAM) during gait in elderly women with and without knee OA. The gait of 45 elderly women between 60 and 70 years of age was evaluated. Twenty-one had knee OR graded 2 or 3 according to Kellgren and Lawrence`s criteria, and 24 who had no OA comprised the control group (CG). The gait conditions were: barefoot, Moleca (R), and modern heeled shoes. Three-dimensional kinematics and ground reaction forces were measured to calculate KAM by inverse dynamics. For both groups, the Moleca (R) provided peak KAM and KAM impulse similar to barefoot walking. For the OA group, the Moleca (R) reduced KAM even more as compared to the barefoot condition during midstance. On the other hand, the modern heeled shoes increased this variable in both groups. Inexpensive, flexible, and non-heeled footwear provided loading on the knee joint similar to a barefoot gait and significant overload decreases in elderly women with and without knee OA, compared to modern heeled shoes. During midstance, the Moleca (R) also allowed greater reduction in the knee joint loads as compared to barefoot gait in elderly women with knee OA, with the further advantage of providing external foot protection during gait. (C) 2011 Elsevier B.V. All rights reserved.

ON THE NATURE OF THE PROTOTYPE LUMINOUS BLUE VARIABLE AG CARINAE. II. WITNESSING A MASSIVE STAR EVOLVING CLOSE TO THE EDDINGTON AND BISTABILITY LIMITS

We show that the significantly different effective temperatures (T(eff)) achieved by the luminous blue variable AG Carinae during the consecutive visual minima of 1985-1990 (T(eff) similar or equal to 22,800 K) and 2000-2001 (T(eff) similar or equal to 17,000 K) place the star on different sides of the bistability limit, which occurs in line-driven stellar winds around T(eff) similar to 21,000 K. Decisive evidence is provided by huge changes in the optical depth of the Lyman continuum in the inner wind as T(eff) changes during the S Dor cycle. These changes cause different Fe ionization structures in the inner wind. The bistability mechanism is also related to the different wind parameters during visual minima: the wind terminal velocity was 2-3 times higher and the mass-loss rate roughly two times smaller in 1985-1990 than in 2000-2003. We obtain a projected rotational velocity of 220 +/- 50 km s(-1) during 1985-1990 which, combined with the high luminosity (L(star) = 1.5 x 10(6) L(circle dot)), puts AG Car extremely close to the Eddington limit modified by rotation (Omega Gamma limit): for an inclination angle of 90 degrees, Gamma(Omega) greater than or similar to 1.0 for M(circle dot) less than or similar to 60. Based on evolutionary models and mass budget, we obtain an initial mass of similar to 100 M(circle dot) and a current mass of similar to 60-70 M(circle dot) for AG Car. Therefore, AG Car is close to, if not at, the Omega Gamma limit during visual minimum. Assuming M = 70 M(circle dot), we find that Gamma(Omega) decreases from 0.93 to 0.72 as AG Car expands toward visual maximum, suggesting that the star is not above the Eddington limit during maximum phases.

Factors influencing creatine loading into human skeletal muscle

This review describes several factors involved in regulating skeletal muscle creatine uptake and total creatine content. Skeletal muscle total creatine content increases with oral creatine supplementation, although the response is variable. Factors that may account for this variation are carbohydrate intake, physical activity, training status, and possibly fiber type.

Effects of creatine loading and prolonged creatine supplementation of body composition, fuel selection, sprint and endurance performance in humans

Most research on creatine has focused on short-term creatine loading and its effect on high-intensity performance capacity. Some studies have investigated the effect of prolonged creatine use during strength training. However, studies on the effects of prolonged creatine supplementation are lacking. In the present study, we have assessed the effects of both creatine loading and prolonged supplementation on muscle creatine content, body composition, muscle and whole-body oxidative capacity, substrate utilization during submaximal exercise, and on repeated supramaximal sprint, as well as endurance-type time-trial performance on a cycle ergometer. Twenty subjects ingested creatine or a placebo during a 5-day loading period (20g·day^-1) after which supplementation was continued for up to 6 weeks (2g·day^-1). Creatine loading increased muscle free creatine, creatine phosphate (CrP) and total creatine content (P<0.05). The subsequent use of a 2g·day^-1 maintenance dose, as suggested by an American College of Sports Medicine Roundtable, resulted in a decline in both the elevated CrP and total creatine content and maintenance of the free creatine concentration. Both short- and long-term creatine supplementation improved performance during repeated supramaximal sprints on a cycle ergometer. However, whole-body and muscle oxidative capacity, substrate utilization and time-trial performance were not affected. The increase in body mass following creatine loading was maintained after 6 weeks of continued supplementation and accounted for by a corresponding increase in fat-free mass. This study provides definite evidence that prolonged creatine supplementation in humans does not increase muscle or whole-body oxidative capacity and, as such, does not influence substrate utilization or performance during endurance cycling exercise. In addition, our findings suggest that prolonged creatine ingestion induces an increase in fat-free mass.

Performance of the Giant Reed (Arundo donax) in experimental wetlands receiving variable loads of industrial stormwater

Two emergent macrophytes, Arundo donax and Phragmites australis, were established in experimental subsurface flow, gravel-based constructed wetlands (CWs) and challenged by untreated stormwater collected from the hard-pan and other surfaces of a dairy processing factory in south-west Victoria, Australia. The hydraulic loading rate was tested at two levels, sequentially, 3.75 and 7.5 cm day -1. Some of the monitored variables were removed more efficiently by the planted beds in comparison to unplanted CWs (biochemical oxygen demand (BOD), total nitrogen (TN) and total phosphorus (TP); p<0.007) but there was no significant difference between the A. donax and P. australis CWs in removal of BOD, suspended solids (SS) and TN (p>0.007) at 3.75 cm day -1 or SS and TN at 7.5 cm day -1. At 3.75 cm day -1, BOD, SS, TN and TP removal in the A. donax and P. australis CWs was 71%, 61%, 78% and 75% and 65%, 60%, 73% and 41%, respectively. Nutrient removal at 7.5 cm day -1 in the A. donax and P. australis beds was 87%, 91%, 84% and 71% and 96%, 94%, 87% and 55%, respectively. As expected, the A. donax CWs produced considerably more biomass (10±1.2 kg wet weight) than the P. australis CWs (2.7±1.2 kg wet weight). This equates to approximately 107 and 36 tonnes ha -1 year -1 biomass (dry weight) for A. donax and P. australis, respectively (assuming 250 days of growing season and singlecut harvest). The performance similarity of the A. donax- and P. australis-planted CWs indicates that either may be used in HSSF wetlands treating dairy factory stormwater, although the planting of A. donax provides additional opportunities for secondary income streams through utilisation of the biomass produced.

Microstructural response of nanocrystalline Al to cyclic loading

The data is derived from an investigation into the microstructural changes of nanostructure Al (produced by cryo-rolling) in response to cyclic loading using electron microscopy and EBSD. The aim is to develop a better understanding of the deformation mechanisms in ultrafine grained/nanostructure metals under cyclic loading conditions.

In-situ white beam microdiffraction study of the deformation behavior in polycrystalline magnesium alloy during uniaxial loading

Scanning white beam X-ray microdiffraction has been used to study the heterogeneous grain deformation in a polycrystalline Mg alloy (MgAZ31). The high spatial resolution achieved on beamline 7.3.3 at the Advanced Light Source provides a unique method to measure the elastic strain and orientation of single grains as a function of applied load. To carry out in-situ measurements a light weight (~0.5kg) tensile stage, capable of providing uniaxial loads of up to 600kg, was designed to collect diffraction data on the loading and unloading cycle. In-situ observation of the deformation process provides insight about the crystallographic deformation mode via twinning and dislocation slip.

Monitoring corrosion of reinforced concrete beams in a chloride containing environment under different loading levels

Corrosion has significant adverse effects on the durability of reinforced concrete (RC) structures, especially those exposed to a marine environment and subjected to mechanical stress, such as bridges, jetties, piers and wharfs. Previous studies have been carried out to investigate the corrosion behaviour of steel rebar in various concrete structures, however, few studies have focused on the corrosion monitoring of RC structures that are subjected to both mechanical stress and environmental effects. This paper presents an exploratory study on the development of corrosion monitoring and detection techniques for RC structures under the combined effects of external loadings and corrosive media. Four RC beams were tested in 3% NaCl solutions under different levels of point loads. Corrosion processes occurring on steel bars under different loads and under alternative wetting - drying cycle conditions were monitored. Electrochemical and microscopic methods were utilised to measure corrosion potentials of steel bars; to monitor galvanic currents flowing between different steel bars in each beam; and to observe corrosion patterns, respectively. The results indicated that steel corrosion in RC beams was affected by local stress. The point load caused the increase of galvanic currents, corrosion rates and corrosion areas. Pitting corrosion was found to be the main form of corrosion on the surface of the steel bars for most of the beams, probably due to the local concentration of chloride ions. In addition, visual observation of the samples confirmed that the localities of corrosion were related to the locations of steel bars in beams. It was also demonstrated that electrochemical devices are useful for the detection of RC beam corrosion.