Physical properties of different sea ice types at ArcticNet, CFL and CASES ice stations, eastern Beaufort Sea

A study of the polarimetric backscattering response of newly formed sea ice types under a large assortment of surface coverage was conducted using a ship-based C-band polarimetric radar system. Polarimetric backscattering results and physical data for 40 stations during the fall freeze-up of 2003, 2006, and 2007 are presented. Analysis of the copolarized correlation coefficient showed its sensitivity to both sea ice thickness and surface coverage and resulted in a statistically significant separation of ice thickness into two regimes: ice less than 6 cm thick and ice greater than 8 cm thick. A case study quantified the backscatter of a layer of snow infiltrated frost flowers on new sea ice, showing that the presence of the old frost flowers can enhance the backscatter by more than 6 dB. Finally, a statistical analysis of a series of temporal-spatial measurements over a visually homogeneous frost-flower-covered ice floe identified temperature as a significant, but not exclusive, factor in the backscattering measurements.

Defect chaos and bursts: Hexagonal rotating convection and the complex Ginzburg-Landau equation

We employ numerical computations of the full Navier-Stokes equations to investigate non-Boussinesq convection in a rotating system using water as the working fluid. We identify two regimes. For weak non- Boussinesq effects the Hopf bifurcation from steady to oscillating (whirling) hexagons is supercritical and typical states exhibit defect chaos that is systematically described by the cubic complex Ginzburg-Landau equation. For stronger non-Boussinesq effects the Hopf bifurcation becomes subcritical and the oscil- lations exhibit localized chaotic bursting, which is modeled by a quintic complex Ginzburg-Landau equation.

Analysis of mode competition in a monolithic master- oscillator power‐amplifier emitting at 1.5 μm

The optical and radio-frequency spectra of a monolithic master-oscillator power-amplifier emitting at 1.5 ?m have been analyzed in a wide range of steady-state injection conditions. The analysis of the spectral maps reveals that, under low injection current of the master oscillator, the device operates in two essentially different operation modes depending on the current injected into the amplifier section. The regular operation mode with predominance of the master oscillator alternates with lasing of the compound cavity modes allowed by the residual reflectance of the amplifier front facet. The quasi-periodic occurrence of these two regimes as a function of the amplifier current has been consistently interpreted in terms of a thermally tuned competition between the modes of the master oscillator and the compound cavity modes.

Building intuition of iron evolution during solar cell processing through analysis of different process models

An important aspect of Process Simulators for photovoltaics is prediction of defect evolution during device fabrication. Over the last twenty years, these tools have accelerated process optimization, and several Process Simulators for iron, a ubiquitous and deleterious impurity in silicon, have been developed. The diversity of these tools can make it difficult to build intuition about the physics governing iron behavior during processing. Thus, in one unified software environment and using self-consistent terminology, we combine and describe three of these Simulators. We vary structural defect distribution and iron precipitation equations to create eight distinct Models, which we then use to simulate different stages of processing. We find that the structural defect distribution influences the final interstitial iron concentration ([Fe-i]) more strongly than the iron precipitation equations. We identify two regimes of iron behavior: (1) diffusivity-limited, in which iron evolution is kinetically limited and bulk [Fe-i] predictions can vary by an order of magnitude or more, and (2) solubility-limited, in which iron evolution is near thermodynamic equilibrium and the Models yield similar results. This rigorous analysis provides new intuition that can inform Process Simulation, material, and process development, and it enables scientists and engineers to choose an appropriate level of Model complexity based on wafer type and quality, processing conditions, and available computation time.

The elasticity and failure of fluid-filled cellular solids: Theory and experiment

We extend and apply theories of filled foam elasticity and failure to recently available data on foods. The predictions of elastic modulus and failure mode dependence on internal pressure and on wall integrity are borne out by photographic evidence of distortion and failure under compressive loading and under the localized stress applied by a knife blade, and by mechanical data on vegetables differing only in their turgor pressure. We calculate the dry modulus of plate-like cellular solids and the cross over between dry-like and fully fluid-filled elastic response. The bulk elastic properties of limp and aging cellular solids are calculated for model systems and compared with our mechanical data, which also show two regimes of response. The mechanics of an aged, limp beam is calculated, thus offering a practical procedure for comparing experiment and theory. This investigation also thereby offers explanations of the connection between turgor pressure and crispness and limpness of cellular materials.

Generalized flows, intrinsic stochasticity, and turbulent transport

The study of passive scalar transport in a turbulent velocity field leads naturally to the notion of generalized flows, which are families of probability distributions on the space of solutions to the associated ordinary differential equations which no longer satisfy the uniqueness theorem for ordinary differential equations. Two most natural regularizations of this problem, namely the regularization via adding small molecular diffusion and the regularization via smoothing out the velocity field, are considered. White-in-time random velocity fields are used as an example to examine the variety of phenomena that take place when the velocity field is not spatially regular. Three different regimes, characterized by their degrees of compressibility, are isolated in the parameter space. In the regime of intermediate compressibility, the two different regularizations give rise to two different scaling behaviors for the structure functions of the passive scalar. Physically, this means that the scaling depends on Prandtl number. In the other two regimes, the two different regularizations give rise to the same generalized flows even though the sense of convergence can be very different. The “one force, one solution” principle is established for the scalar field in the weakly compressible regime, and for the difference of the scalar in the strongly compressible regime, which is the regime of inverse cascade. Existence and uniqueness of an invariant measure are also proved in these regimes when the transport equation is suitably forced. Finally incomplete self similarity in the sense of Barenblatt and Chorin is established.

THE KYOTO PROTOCOL AND THE WTO: INSTITUTIONAL EVOLUTION AND ADAPTATION. CEPS Policy Brief No. 28/December

Overview. Questions about the interface between the multilateral climate regime embodied in the Kyoto Protocol and the multilateral trade regime embodied in the World Trade Organisation (WTO) have become especially timely since the fall of 2001. At that time, ministerial-level meetings in Marrakech and Doha agreed to advance the agendas, respectively, for the implementation of the Kyoto Protocol and for negotiations on further agreements at the WTO. There have been concerns that each of these multilateral arrangements could constrain the effectiveness of the other, and these concerns will become more salient with the entry into force of the Kyoto Protocol. There are questions about whether and how the rights and obligations of the members of the WTO and the parties to the Protocol may conflict. Of particular concern is whether provisions in the Protocol, as well as government policies and business activities undertaken in keeping with those provisions, may conflict with the WTO non-discrimination principles of national treatment and most-favoured nation treatment. The WTO agreements that are potentially relevant to climate change issues include many of the individual Uruguay Round agreements and subsequent agreements as well. The principal elements of the Kyoto Protocol that are particularly relevant are its provisions concerning emissions trading, the Clean Development Mechanism, Joint Implementation, enforcement, and parties’ policies and measures. In combination, therefore, there are numerous potential points of intersection between the elements of the Kyoto Protocol and the WTO agreements. Previous studies have clarified many issues, as they have focused on particular aspects of the regimes’ relationships. Yet, some analyses suggest that the two regimes are largely compatible and even mutually reinforcing, while others suggest that there are significant conflicts between them. Those and other studies are referenced in the ‘suggestions for further reading’ section at the end of the paper.1 The present paper seeks to expand on those studies by providing additional breadth and depth to understanding of the issues. The analysis gives special attention to key issues on the agenda – i.e. issues that are particularly problematic because of the likelihood of occurrence of specific conflicts and the significance of their economic and/or political consequences. The paper adopts a modified ‘triage’ approach, which classifies points of intersection as (a) highly problematic and clearly in need of further attention, (b) perhaps problematic but less urgent, and (c) apparently not problematic, at least at this point in time. The principal conclusions are that: · The missions and objectives of the two regimes are largely compatible, and their operations are potentially mutually reinforcing in several respects. · Some provisions of the multilateral agreements that may superficially seem at odds are not likely to become particularly problematic in practice. · ‘Domestic policies and measures’ that governments may undertake in the context of the Protocol could pose difficult issues in the context of WTO dispute cases. · Recent WTO agreements and dispute cases acknowledge the legitimacy of the ‘precautionary principle’ and are thus consistent with the environmental protection objectives of the Protocol. · The relative newness of the climate regime creates opportunities for institutional adaptation, as compared with the constraints of tradition in the trade-investment regime. · The prospect of largely independent evolutionary paths for the two regimes poses a series of issues about future international regime design and management, which may require new institutional arrangements. In sum, the present paper thus finds that although there are some areas of interaction that are problematic, the two regimes may nevertheless co-exist in relative harmony in other respects –more like ‘neighbours’ than either ‘friends’ or ‘foes’, as Krist (2001) has suggested.

Flowback of solids through distribution plates of gas fluidized beds and associated phenomena

This work is concerned with a study of certain phenomena related to the performance and design of distributors in gas fluidized beds with particular regard to flowback of solid particles. The work to be described is divided into two parts. I. In Part one, a review of published material pertaining to distribution plates, including details from the patent specifications, has been prepared. After a chapter on the determination of the incipient fluidizing velocity, the following aspects of multi-orifice distributor plates in gas fluidized beds have been studied: (i) The effect of the distributor on bubble formation related to the way in which even distribution of bubbles on the top surface of the fluidized bed is obtained, e.g. the desirable pressure drop ratio ?PD/?PB for the even distribution of gas across the bed. Ratios of distributor pressure drop ?PD to bed pressure drop at which stable fluidization occurs show reasonable agreement with industrial practice. There is evidence that larger diameter beds tend to be less stable than smaller diameter beds when these are operated with shallow beds. Experiments show that in the presence of the bed the distributor pressure drop is reduced relative to the pressure drop without the bed, and this pressure drop in the former condition is regarded as the appropriate parameter for the design of the distributor. (ii) Experimental measurements of bubble distribution at the surface has been used to indicate maldistribution within the bed. Maldistribution is more likely at low gas flow rates and with distributors having large fractional free area characteristics (i.e. with distributors having low pressure drops). Bubble sizes obtained from this study, as well as those of others, have been successfully correlated. The correlation produced implies the existence of a bubble at the surface of an orifice and its growth by the addition of excess gas from the fluidized bed. (iii) For a given solid system, the amount of defluidized particles stagnating on the distributor plate is influenced by the orifice spacing, bed diameter and gas flow rate, but independent of the initial bed height and the way the orifices are arranged on the distributor plate. II. In Part two, solids flowback through single and multi-orifice distributors in two-dimensional and cylindrical beds of solids fluidized with air has been investigated. Distributors equipped with long cylindrical nozzles have also been included in the study. An equation for the prediction of free flowback of solids through multi-orifice distributors has been derived. Under fluidized conditions two regimes of flowback have been differentiated, namely Jumping and weeping. Data in the weeping regime have been successfully correlated. The limiting gas velocity through the distributor orifices at which flowback is completely excluded is found to be indepnndent of bed height, but a function of distributor design and physical properties of gas and solid used. A criterion for the prediction of this velocity has been established. The decisive advantage of increasing the distributor thickness or using nozzles to minimize solids flowback in fluidized beds has been observed and the opportunity taken to explore this poorly studied subject area. It has been noted, probably for the first time, that with long nozzles, there exists a critical nozzle length above which uncontrollable downflow of solids occurs. A theoretical model for predicting the critical length of a bundle of nozzles in terms of gas velocity through the nozzles has been set up. Theoretical calculations compared favourably with experiments.

Ambulatory EEG monitoring in the diagnosis and treatment of epilepsy and related disorders

Ambulatory EEG recording enables patients with epilepsy and related disorders to be monitored in an unrestricted environment for prolonged periods. Attacks can therefore be recorded and EEG changes at the time can aid diagnosis. The relevant Iiterature is reviewed and a study made of' 250 clinical investigations. A study was also made of the artefacts,encountered during ambulatory recording. Three quarters of referrals were for distinguishing between epileptic and non-epileptic attacks. Over 60% of patients showed no abnormality during attacks. In comparison with the basic EEG the ambulatory EEG provided about ten times as much information. A preliminary follow-up study showed that results, of ambulatory monitoring agreed with the final diagnosis in 8 of 12 patients studied. Of 10 patients referred, for monitoring the occurrence of absence seizures, 8 showed abnormality during the baslcJ EEG .and 10 during the ambulatory EEG. Other patients. were referred: for sleep recording and to clarify the seizure type. An investigation into once daily (OD) versus twice daily administration of sodium valproate in patients with absence seizures showed that an OD regime was equally as effective as a BD regime. Circadian variations in spike and wave activity in patients on and off treatment were also examined. There was significant agreement between subjects on the time of occurrence of abnormality during sleep only, This pattern was not ,affected with treatment nor was there any difference in the daily pattern of occurrence of abnormality between the two regimes. Overall findings suggested that ambulatory monitoring was a valuable tool in the diagnosis and treatment of epilepsy which with careful planning and patient selection could be used in any EEG department and would benefit a:wide range of patients.

The effect of dissolved magnesium on diffusion creep in calcite

We experimentally tested a series of synthetic calcite marbles with varying amounts of dissolved magnesium in a standard triaxial deformation machine at 300 MPa confining pressure, temperatures between 700 and 850°C, stresses between 2 and 100 MPa, and strain rates between 10−7 and 10−3 s−1. The samples were fabricated by hot isostatic pressing of a mixture of calcite and dolomite at 850°C and 300 MPa. The fabrication protocol resulted in a homogeneous, fine-grained high-magnesian calcite aggregate with minimal porosity and with magnesium contents between 0.07 and 0.17 mol% MgCO3. At stresses below 40 MPa the samples deformed with linear viscosity that depended inversely on grain size to the 3.26±0.51 power, suggesting that the mechanisms of deformation were some combination of grain boundary diffusion and grain boundary sliding. Because small grain sizes tended to occur in the high-magnesium calcite, the strength also appeared to vary inversely with magnesium content. However, the strength at constant grain size does not depend on the amount of dissolved magnesium, and thus, the impurity effect seems to be indirect. At stresses higher than 40 MPa, the aggregates become non-linearly viscous, a regime we interpret to be dislocation creep. The transition between the two regimes depends on grain size, as expected. The activation energy for diffusion creep is 200±30 kJ/mol and is quite similar to previous measurements in natural and synthetic marbles deformed at similar conditions with no added magnesium.

Effect of fertilization and type of pruning on quality of fresh and dehydrated Stevia rebaudiana

Mestrado em Engenharia Alimentar - Instituto Superior de Agronomia - UL

Fingerprints of a size-dependent crossover in the dimensionality of electronic conduction in Au-seeded Ge nanowires

We studied the electrical transport properties of Au-seeded germanium nanowires with radii ranging from 11 to 80 nm at ambient conditions. We found a non-trivial dependence of the electrical conductivity, mobility and carrier density on the radius size. In particular, two regimes were identified for large (lightly doped) and small (stronger doped) nanowires in which the charge-carrier drift is dominated by electron-phonon and ionized-impurity scattering, respectively. This goes in hand with the finding that the electrostatic properties for radii below ca. 37 nm have quasi one-dimensional character as reflected by the extracted screening lengths.

Spectral properties of resonant Bose-Fermi mixtures

The object of study of the present work are Bose-Fermi mixtures in three dimensions at zero temperature. The system is characterized by a great tunability of physical parameters that is achieved by means of a Fano-Feshbach resonance. As a result, there are mainly two regimes: we move from a situation in which bosons and fermions are weakly interacting to a context in which bosons are coupled to fermions so as to form molecules that are composite fermions, as the coupling between the two types of particles is increased. In the former case, we can describe the mixture as a weakly attractive Bose-Fermi one, while in the latter the same is described in terms of molecules and excess atoms or particles which are unpaired. The main aim of the thesis is to analyze the spectral weight functions which represent the single-particle excitation spectra of the system and are relevant to recent radio-frequency spectroscopy experiments of the system. In order to pursue this objective, diagrammatic methods are used. The formalism is developed within the T-matrix approach: it consists of an approximate calculation whichselects exclusively the class of Feynman’s diagrams that collects all possible repeated boson-fermion interaction.

Safety and Effectiveness of two treatment regimes with tranexamic acid to minimize inflammatory response in elective cardiopulmonary bypass patients: a randomized double-blind, dose-dependent, phase IV clinical trial

Background. In cardiopulmonary bypass (CPB) patients, fibrinolysis may enhance postoperative inflammatory response. We aimed to determine whether an additional postoperative dose of antifibrinolytic tranexamic acid (TA) reduced CPB-mediated inflammatory response (IR). Methods. We performed a randomized, double-blind, dose-dependent, parallel-groups study of elective CPB patients receiving TA. Patients were randomly assigned to either the single-dose group (40 mg/Kg TA before CPB and placebo after CPB) or the double-dose group (40 mg/Kg TA before and after CPB). Results. 160 patients were included, 80 in each group. The incident rate of IR was significantly lower in the double-dose-group TA2 (7.5% vs. 18.8% in the single-dose group TA1; P = 0.030). After adjusting for hypertension, total protamine dose and temperature after CPB, TA2 showed a lower risk of IR compared with TA1 [OR: 0.29 (95% CI: 0.10-0.83), (P = 0.013)]. Relative risk for IR was 2.5 for TA1 (95% CI: 1.02 to 6.12). The double-dose group had significantly lower chest tube bleeding at 24 hours [671 (95% CI 549-793 vs. 826 (95% CI 704-949) mL; P = 0.01 corrected-P significant] and lower D-dimer levels at 24 hours [489 (95% CI 437-540) vs. 621(95% CI: 563-679) ng/mL; P = 0.01 corrected-P significant]. TA2 required lower levels of norepinephrine at 24 h [0.06 (95% CI: 0.03-0.09) vs. 0.20(95 CI: 0.05-0.35) after adjusting for dobutamine [F = 6.6; P = 0.014 corrected-P significant]. We found a significant direct relationship between IL-6 and temperature (rho = 0.26; P < 0.01), D-dimer (rho = 0.24; P < 0.01), norepinephrine (rho = 0.33; P < 0.01), troponin I (rho = 0.37; P < 0.01), Creatine-Kinase (rho = 0.37; P < 0.01), Creatine Kinase-MB (rho = 0.33; P < 0.01) and lactic acid (rho = 0.46; P < 0.01) at ICU arrival. Two patients (1.3%) had seizure, 3 patients (1.9%) had stroke, 14 (8.8%) had acute kidney failure, 7 (4.4%) needed dialysis, 3 (1.9%) suffered myocardial infarction and 9 (5.6%) patients died. We found no significant differences between groups regarding these events. Conclusions. Prolonged inhibition of fibrinolysis, using an additional postoperative dose of tranexamic acid reduces inflammatory response and postoperative bleeding (but not transfusion requirements) in CPB patients. A question which remains unanswered is whether the dose used was ideal in terms of safety, but not in terms of effectiveness.

Heliotropic responses of soybean cultivars at three phenological stages and under two water regimes

The objectives of this work were to determine the heliotropic movements of the upper trifoliates for two soybean cultivars, BR 16 and Embrapa 48, during a daily cycle, in three phenological stages and two water regimes, and to estimate the impact of irrigation and daily leaflet movements on agronomic characteristics and grain yield. Heliotropic movements were studied in three phenological stages: V4-V6, V7-V10, and R5 in irrigated and non-irrigated plots. For each stage, the leaflet elevation and azimuth were measured hourly. Under a low (V4-V6 stage) and mid (V7-V10 stage) leaf area index (LAI) the diaheliotropism was slightly more frequent and intensive in non-irrigated than in irrigated plants, only at early morning and late afternoon hours. At R5 stage (high LAI) the paraheliotropism of superior trifoliates was predominant and more intensive in non-irrigated plants. The heliotropic movements are correlated to carbon gain, but not to environment (light intensity or temperature), for measurements at 11h. 'Embrapa 48' expresses greater paraheliotropism than 'BR 16' at high LAI, while 'BR 16' displays lower heliotropic plasticity under irrigation. In spite of significant heliotropic differences, genotype and water availability treatments did not influence the final grain yield.