A '3-body' abrasion wear study of bioceramics for total hip joint replacements

The current study focuses on the effect of the material type and the lubricant on the abrasive wear behaviour of two important commercially available ceramic on ceramic prosthetic systems, namely, Biolox(R) forte and Bioloxl(R) delta (CeramTec AG, Germany). A standard microabrasion wear apparatus was used to produce '3-body' abrasive wear scars with three different lubricants: ultrapure water, 25 vol% new-born calf serum solution and 1 wt% carboxymethyl cellulose sodium salt (CMC-Na) solution. 1 mu m alumina particles were used as the abrasive. The morphology of the wear scar was examined in detail using Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM). Subsurface damage accumulation was investigated by Focused Ion Beam (FIB) cross-sectional milling and Transmission Electron Microscopy (TEM). The effect of the lubricant on the '3-body' abrasive wear mechanisms is discussed and the effect of material properties compared. (C) 2009 Elsevier B.V. All rights reserved.

Micro-abrasion-corrosion of cast CoCrMo-Effects of micron and sub-micron sized abrasives

The abrasion damage on retrieved CoCrMo based hip joints is reported to be influenced by the entrainment of micron and sub-micron sized debris/hard particles. This paper represents the first attempt to look into the effects of relatively soft abrasives with micron and sub-micron dimensions on the abrasion mechanisms and the abrasion-corrosion performance of the cast CoCrMo in simulated hip joint environments. A modified micro-abrasion tester incorporating a liquid tank and a three-electrode electrochemical cell was used. Al O (300 nm and 1 μm) and sub-micron sized BaSO abrasives were chosen as being comparable in the size and hardness to the wear particles found in vivo. Results show that the specific wear rates of cast CoCrMo are dependent on the abrasive particle size, hardness and volume concentration. Larger particle size, higher hardness and greater abrasive volume fractions gave greater wear rates. The wear-induced corrosion current generally increases with increasing wear rates, and the presence of proteins seems to suppress the wear-induced corrosion current especially when abrasive volume fractions were high. This study shows that the nature of abrasives and the test solutions are both important in determining the wear mechanisms and the abrasion-corrosion response of cast CoCrMo. These findings provide new and important insights into the in vivo wear mechanisms of CoCrMo. © 2009 Elsevier B.V. All rights reserved.

Micro-scale abrasion behaviour of electroless Ni-P-SiC coating on aluminium alloy

Electroless nickel (EN) and electroless nickel composite (ENC) coatings were deposited on aluminium alloy substrate, LM24. The micro abrasion test was conducted to study the wear behaviour of the coatings with the effect of SiC concentration. Microhardness of the coatings was tested also. The wear scars were analysed using optical microscope and scanning electron microscope (SEM). The wear resistance was found to be improved in composite coating that has higher microhardness as compared to particles free and the bare aluminium substrate. In as-deposited condition for the composite coating, the wear volume increases on increase in SiC percentage in the coating but is found to be minimum for lower SiC percentage. The increase in hardness on heat treatment at 400°C is due to the hardening or grain coarsening with the formation Ni3P.

Role of abrasive material on micro-abrasion wear tests

Micro-abrasion wear tests with ball-cratering configuration are widely used. Sources of variability are already studied by different authors and conditions for testing are parameterized by BS EN 1071-6: 2007 standard which refers silicon carbide as abrasive. However, the use of other abrasives is possible and allowed. In this work, ball-cratering wear tests were performed using four different abrasive particles of three dissimilar materials: diamond, alumina and silicon carbide. Tests were carried out under the same conditions on a steel plate provided with TiB2 hard coating. For each abrasive, five different test durations were used allowing understanding the initial wear phenomena. Composition and shape of abrasive particles were investigated by SEM and EDS. Scar areas were observed by optical and electronic microscopy in order to understand the wear effects caused by each of them. Scar geometry and grooves were analyzed and compared. Wear coefficient was calculated for each situation. It was observed that diamond particles produce well-defined and circular wear scars. Different silicon carbide particles presented dissimilar results as consequence of distinct particle shape and size distribution.

Influence of the abrasive particles size in the micro-abrasion wear tests of TiAlSiN thin coatings

Ball rotating micro-abrasion tribometers are commonly used to carry out wear tests on thin hard coatings. In these tests, different kinds of abrasives were used, as alumina (Al2O3), silicon carbide (SiC) or diamond. In each kind of abrasive, several particle sizes can be used. Some studies were developed in order to evaluate the influence of the abrasive particle shape in the micro-abrasion process. Nevertheless, the particle size was not well correlated with the material removed amount and wear mechanisms. In this work, slurry of SiC abrasive in distilled water was used, with three different particles size. Initial surface topography was accessed by atomic force microscopy (AFM). Coating hardness measurements were performed with a micro-hardness tester. In order to evaluate the wear behaviour, a TiAlSiN thin hard film was used. The micro-abrasion tests were carried out with some different durations. The abrasive effect of the SiC particles was observed by scanning electron microscopy (SEM) both in the films (hard material) as in the substrate (soft material), after coating perforation. Wear grooves and removed material rate were compared and discussed.

Micro-abrasion wear behaviour of TiAlCrSiN nanostructured coatings

The injection process of glass fibres reinforced plastics promotes the moulds surface degradation by erosion. In order to improve its wear resistance, several kinds of PVD thin hard coatings were used. It is well-known that nanostructures present a better compromise between hardness and toughness. Indeed, when the coating is constituted by a large number of ultra-thin different layers, cracks and interface troubles tend to decrease. However, it is not clear that these nanostructures present a better wear behaviour in erosion processes. In order to study its wear behaviour, a sputtered PVD nanostructured TiAlCrSiN coating was used. The substrate and film surfaces topography were analyzed by profilometry and atomic force microscopy techniques. Film adhesion to the substrate was evaluated by scratch tests. The surface hardness was measured with a Vickers micro-hardness tester. The wear resistance was evaluated by micro-abrasion with a rotating ball tribometer tests. Slurry of SiC particles in distilled water was used in order to provoke the surface abrasion. Different duration tests were performed in order to analyze the wear evolution. After these tests, the wear mechanisms developed were analyzed by scanning electron microscopy. Wear craters were measured and the wear rate was calculated and discussed. With the same purpose, coated inserts were mounted in an injection mould working with a 30% glass fibres reinforced polypropylene. After 45 000 cycles no relevant wear was registered.

Abrasion, transport and distribution of sediment in selected streams of Southern Ontario and Western New York /

The rate of decrease in mean sediment size and weight per square metre along a 54 km reach of the Credit River was found to depend on variations in the channel geometry. The distribution of a specific sediment size consist of: (1) a transport zone; (2) an accumulation zone; and (3) a depletion zone. These zones shift downstream in response to downcurrent decreases in stream competence. Along a .285 km man-made pond, within the Credit River study area, the sediment is also characterized by downstream shifting accumulation zones for each finer clast size. The discharge required to initiate movement of 8 cm and 6 cm blocks in Cazenovia Creek is closely approximated by Baker and Ritter's equation. Incipient motion of blocks in Twenty Mile Creek is best predicted by Yalin's relation which is more efficient in deeper flows. The transport distance of blocks in both streams depends on channel roughness and geometry. Natural abrasion and distribution of clasts may depend on the size of the surrounding sediment and variations in flow competence. The cumulative percent weight loss with distance of laboratory abraded dolostone is defined by a power function. The decrease in weight of dolostone follows a negative exponential. In the abrasion mill, chipping causes the high initial weight loss of dolostone; crushing and grinding produce most of the subsequent weight loss. Clast size was found to have little effect on the abrasion of dolostone within the diameter range considered. Increasing the speed of the mill increased the initial amount of weight loss but decreased the rate of abrasion. The abrasion mill was found to produce more weight loss than stream action. The maximum percent weight loss determined from laboratory and field abrasion data is approximately 40 percent of the weight loss observed along the Credit River. Selective sorting of sediment explains the remaining percentage, not accounted for by abrasion.

Abrasion control on dune colour: Muleshoe Dunes, SW USA

The Muleshoe Dunes, an east-west trending dunefield on the border separating Texas and New Mexico, consist of two distinct components: a white (carbonate rich) component and an overlying pink (quartz rich) component. The pink component exhibits significant spatial variation in redness. The reddest sands, in the western part of the dunefield, decrease in redness towards the east. This gradient is thought to result from abrasion of all iron-rich, red clay coating as the sediments were transported eastward by Late Quaternary aeolian processes. The effects of aeolian abrasion on the spectral signature and surface texture of the sediments were examined using laboratory abrasion experiments. Changes in spectral reflectance of abrasion samples from the laboratory were compared to field samples that were abraded naturally because of sediment transport. The changes resulting from increased time of abrasion are similar to those observed with increased distance downwind in the dunefield. These results suggest that downwind abrasion can explain the pattern of dune colour in the Muleshoe Dunes, although this does not preclude other possible causes. (C) 2008 Elsevier B.V. All rights reserved.

Dust production and the release of iron oxides resulting from the aeolian abrasion of natural dune sands

Global dust trajectories indicate that significant quantities of aeolian-transported iron oxides originate in contemporary dryland areas. One potential source is the iron-rich clay coatings that characterize many sand-sized particles in desert dunefields. This paper uses laboratory experiments to determine the rate at which these coatings can be removed from dune sands by aeolian abrasion. The coatings impart a red colour to the grains to which previous researchers have assigned variable geomorphological significance. The quantities or iron removed during a 120 hour abrasion experiment are small (99 mg kg(-1)) and difficult to detect by eye; however, high resolution spectroscopy clearly indicates that ferric oxides are released during abrasion and the reflectance of the particles alters. One of the products of aeolian abrasion is fine particles (<10 mum diameter) with the potential for long distance transport. Copyright (C) 2004 John Wiley Sons, Ltd.

Abrasion control on dune colour: Muleshoe Dunes, SW USA

The Muleshoe Dunes, an east-west trending dunefield on the border separating Texas and New Mexico, consist of two distinct components: a white (carbonate rich) component and an overlying pink (quartz rich) component. The pink component exhibits significant spatial variation in redness. The reddest sands, in the western part of the dunefield, decrease in redness towards the east. This gradient is thought to result from abrasion of all iron-rich, red clay coating as the sediments were transported eastward by Late Quaternary aeolian processes. The effects of aeolian abrasion on the spectral signature and surface texture of the sediments were examined using laboratory abrasion experiments. Changes in spectral reflectance of abrasion samples from the laboratory were compared to field samples that were abraded naturally because of sediment transport. The changes resulting from increased time of abrasion are similar to those observed with increased distance downwind in the dunefield. These results suggest that downwind abrasion can explain the pattern of dune colour in the Muleshoe Dunes, although this does not preclude other possible causes. (C) 2008 Elsevier B.V. All rights reserved.

Assessing the frictional and abrasion-resisting properties of hooves and claws

Hoof abrasion and slips on floors are known to have negative effects on animal health and welfare. This paper describes a new design of test rig for use in a universal materials test machine. The rig enables the frictional and abrasion-resisting properties of hoof horn to be investigated under controlled conditions, in vitro. To assess the performance of the rig, pilot experiments were carried out which indicated both test surface roughness and specimen hydration interact to alter frictional coefficient and mechanical work done to lose a unit volume of hoof material by abrasive wear.

Artefacts between disciplines: the toothbrush and the axe

This paper takes the form of a dialogue between an archaeologist and a sociologist. In recent years, interdisciplinary working has become increasingly fashionable within academia. The aim of our exchange was to establish exactly what implications this way of working has for understandings of material culture. Our methodology was simple, involving the ‘archaeological’ and ‘sociological’ analysis of two different objects. In undertaking this work, we hoped to bring about new or different understandings of the objects under scrutiny. The process was indeed successful, but not necessarily in the ways we had expected. Ultimately, it revealed a complex set of questions about how the materials of culture are conceptualized and understood, and led us to a renewed appreciation of the theoretical and methodological qualities of what we do within our respective disciplines

Micro-abrasion of flint artefacts by mobile sediments: a taphonomic approach

Fluvial redeposition of stone artifacts is a major complicating factor in the interpretation of Lower Palaeolithic open-air archaeological sites. However, the microscopic examination of lithic surfaces may provide valuable background information on the transport history of artifacts, particularly in low energy settings. Replica flint artifacts were therefore abraded in an annular flume and examined with a scanning electron microscope. Results showed that abrasion time, sediment size, and artifact transport mode were very sensitive predictors of microscopic surface abrasion, ridge width, and edge damage (p < 0.000). These results suggest that patterns of micro-abrasion of stone artifacts may enhance understanding of archaeological assemblage formation in fluvial contexts

In vitro and clinical evaluation of specific dentifrices for complete denture hygiene

To study the physical properties of two experimental dentifrices for complete denture hygiene, their effect on denture biofilm removal and antimicrobial properties by means of a clinical trial. The experimental dentifrices comprised two compositions. One was based on the addition of 1% chloramine T (D1) and the other on the presence of 0.01% fluorosurfactant (D2). Measurements of density, pH, consistency, rheological features and abrasiveness were conducted. Sixty complete denture wearers were randomly assigned to three groups and were instructed to brush their dentures with a specific toothbrush: (1) Water (control); (2) D1; or (3) D2. Each method was used for 21 days. Denture biofilm was disclosed by a 1% neutral red solution and quantified by means of digital photos taken from the internal surface. Microbiological assessment was conducted to quantify Candida sp. and mutans streptococci. Data were evaluated by one-way anova and Tukey HSD, or Kruskal-Wallis (alpha = 0.05). Both dentifrices decreased biofilm coverage when compared with the control group. D1 was the most efficacious treatment to reduce mutans streptococci, whereas D2 showed an intermediate outcome (anova, p < 0.040). No treatment influenced Candida albicans or non-albicans species (Kruskal-Wallis, p = 0.163 and 0.746, respectively). It can be concluded that brushing complete dentures with the experimental dentifrices tested could be effective for the removal of denture biofilm.

Evaluation of toothbrush bristles' deterioration used by preschool children

The toothbrush is an effective instrument for oral diseases prevention. The flexibility and status of bristles, as well as the size of the handle are fundamental for an effective toothbrushing. Thus, the assessment of physical characteristics of toothbrushes is important. This study evaluated the deterioration and wear of bristles of toothbrushes used by preschool children. For the sample selection, five elementary schools were assorted from a city of the São Paulo State northwest region, one from each city area. All toothbrushes used by preschool children who aged between 5 and 6 years old and who attended the assorted schools were visually analysed by two calibrated examiners, according to the criteria proposed by Rawls HR, Mkwayi-Tulloch NJ, Casella R, Cosgrove R (J Dent Res 1989; 12: 1781): 0 - it is impossible to state if the toothbrush was used or not; 1 - the bristles seem to be separated within some tufts; 2 - most tufts are separated, many cover other tufts and present a large number of curved and inclined bristles; 3 - most tufts are covered by others and bristles are folded and tipped. In total, 333 toothbrushes were evaluated. The data obtained revealed that 57.96% of the toothbrushes presented adequate condition for utilization (scores 0 and 1), whereas 42.04% presented inadequate bristles for their function (scores 2 and 3). It was concluded that a great number of toothbrushes presented deterioration of the bristles. Thus, there is the need to guide and promote awareness among teachers, parents and children as well as the need to replace toothbrushes.