The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

Repair of segmental bone defects with fiber-reinforced composite: a study of material development and an animal model on rabbits

The Repair of segmental defects in load-bearing long bones is a challenging task because of the diversity of the load affecting the area; axial, bending, shearing and torsional forces all come together to test the stability/integrity of the bone. The natural biomechanical requirements for bone restorative materials include strength to withstand heavy loads, and adaptivity to conform into a biological environment without disturbing or damaging it. Fiber-reinforced composite (FRC) materials have shown promise, as metals and ceramics have been too rigid, and polymers alone are lacking in strength which is needed for restoration. The versatility of the fiber-reinforced composites also allows tailoring of the composite to meet the multitude of bone properties in the skeleton. The attachment and incorporation of a bone substitute to bone has been advanced by different surface modification methods. Most often this is achieved by the creation of surface texture, which allows bone growth, onto the substitute, creating a mechanical interlocking. Another method is to alter the chemical properties of the surface to create bonding with the bone – for example with a hydroxyapatite (HA) or a bioactive glass (BG) coating. A novel fiber-reinforced composite implant material with a porous surface was developed for bone substitution purposes in load-bearing applications. The material’s biomechanical properties were tailored with unidirectional fiber reinforcement to match the strength of cortical bone. To advance bone growth onto the material, an optimal surface porosity was created by a dissolution process, and an addition of bioactive glass to the material was explored. The effects of dissolution and orientation of the fiber reinforcement were also evaluated for bone-bonding purposes. The Biological response to the implant material was evaluated in a cell culture study to assure the safety of the materials combined. To test the material’s properties in a clinical setting, an animal model was used. A critical-size bone defect in a rabbit’s tibia was used to test the material in a load-bearing application, with short- and long-term follow-up, and a histological evaluation of the incorporation to the host bone. The biomechanical results of the study showed that the material is durable and the tailoring of the properties can be reproduced reliably. The Biological response - ex vivo - to the created surface structure favours the attachment and growth of bone cells, with the additional benefit of bioactive glass appearing on the surface. No toxic reactions to possible agents leaching from the material could be detected in the cell culture study when compared to a nontoxic control material. The mechanical interlocking was enhanced - as expected - with the porosity, whereas the reinforcing fibers protruding from the surface of the implant gave additional strength when tested in a bone-bonding model. Animal experiments verified that the material is capable of withstanding load-bearing conditions in prolonged use without breaking of the material or creating stress shielding effects to the host bone. A Histological examination verified the enhanced incorporation to host bone with an abundance of bone growth onto and over the material. This was achieved with minimal tissue reactions to a foreign body. An FRC implant with surface porosity displays potential in the field of reconstructive surgery, especially regarding large bone defects with high demands on strength and shape retention in load-bearing areas or flat bones such as facial / cranial bones. The benefits of modifying the strength of the material and adjusting the surface properties with fiber reinforcement and bone-bonding additives to meet the requirements of different bone qualities are still to be fully discovered.

Characterization and Investigation on Material Compatibilities of Building Integrated Photovoltaic Module Components

Building Integrated Photovoltaics (BIPV) are considered as the future of photovoltaic (PV) technology. The advantage of BIPV system is its multi-functionality; they fulfil the functions of a building envelope with the added benefit of generating power by replacing the traditional roofing and façade materials with PV that generate power. In this thesis, different types of PV cells and modules have been described in detail with their efficiencies and usage trends in the last decade. The different BIPV products for roof and façade are discussed in detail giving several examples. The electricity generation potential of BIPV in selected countries is compared with their actual electricity consumption. Further, the avoided greenhouse gas (GHG) emissions associated with electricity generation from traditional sources and transportation and distribution (T&D) losses are calculated. The results illustrate huge savings in GHGs. In BIPV different types of façade and backsheets are used. In this thesis, selected backsheets and façade were characterized in terms of their surface structure identification using infrared spectroscopy (FTIR-ATR), scanning electron microscopy with energy dispersive X-ray (SEM-EDX) and physical characterization using surface energy measurements. By using FTIR-ATR, surface polymeric materials were identified and with SEM-EDX, identification of the surface elements was possible. Surface energy measurements were useful in finding the adhesives and knowing the surface energies of the various backsheets and façade. The strength of adhesion between the facade and backsheets was studied using peel test. Four different types of adhesives were used to study the fracture pattern and peel tests values to identify the most suitable adhesive. It was found out that pretreatment increased the adhesive strength significantly.

Perception de la vitesse : les bases psychophysiques et neuronales

David Katz a fait l’observation que le mouvement entre la peau et l’objet est aussi important pour le sens du toucher que la lumière l’est pour la vision. Un stimulus tactile déplacé sur la peau active toutes les afférences cutanées. Les signaux résultants sont très complexes, covariant avec différents facteurs dont la vitesse, mais aussi la texture, la forme et la force. Cette thèse explore la capacité des humains à estimer la vitesse et la rugosité de surfaces en mouvements. Les bases neuronales de la vitesse tactile sont aussi étudiées en effectuant des enregistrements unitaires dans le cortex somatosensoriel primaire (S1) du singe éveillé. Dans la première expérience, nous avons montré que les sujets peuvent estimer la vitesse tactile (gamme de vitesses, 30 à 105 mm/s) de surfaces déplacées sous le doigt, et ceci sans indice de durée. Mais la structure des surfaces était essentielle (difficulté à estimer la vitesse d’une surface lisse). Les caractéristiques physiques des surfaces avaient une influence sur l’intensité subjective de la vitesse. La surface plus rugueuse (8 mm d’espacement entre les points en relief) semblait se déplacer 15% plus lentement que les surfaces moins rugueuses (de 2 et 3 mm d’espacement), pour les surfaces périodiques et non périodiques (rangées de points vs disposition aléatoire). L’effet de la texture sur la vitesse peut être réduit en un continuum monotonique quand les estimés sont normalisés avec l’espacement et présentés en fonction de la fréquence temporelle (vitesse/espacement). L'absence de changement des estimés de vitesse entre les surfaces périodiques et non périodiques suggère que les estimés de rugosité devraient aussi être indépendants de la disposition des points. Dans la deuxième expérience, et tel que prévu, une équivalence perceptuelle entre les deux séries de surfaces est obtenue quand les estimés de la rugosité sont exprimés en fonction de l'espacement moyen entre les points en relief, dans le sens de l'exploration. La troisième expérience consistait à rechercher des neurones du S1 qui pourraient expliquer l’intensité subjective de la vitesse tactile. L’hypothèse est que les neurones impliqués devraient être sensibles à la vitesse tactile (40 à 105 mm/s) et à l’espacement des points (2 à 8 mm) mais être indépendants de leur disposition (périodique vs non périodique). De plus, il est attendu que la fonction neurométrique (fréquence de décharge/espacement en fonction de la fréquence temporelle) montre une augmentation monotonique. Une grande proportion des cellules était sensible à la vitesse (76/119), et 82% d’entres elles étaient aussi sensibles à la texture. La sensibilité à la vitesse a été observée dans les trois aires du S1 (3b, 1 et 2). La grande majorité de cellules sensibles à la vitesse, 94%, avait une relation monotonique entre leur décharge et la fréquence temporelle, tel qu’attendu, et ce surtout dans les aires 1 et 2. Ces neurones pourraient donc expliquer la capacité des sujets à estimer la vitesse tactile de surfaces texturées.

Zur Erfassung von form- und materialbedingten Oberflächenstrukturen mit Mikro-Deflexions-Ellipsometrie

Die vorliegende Arbeit berichtet über ein neuartiges, kombiniertes Messverfahren zur gleichzeitigen Erfassung von Form und Material einer glänzenden Probenoberfläche. Die Materialerkennung erfolgt über die polarisationsoptische Brechzahlbestimmung im Messpunkt mit Mikroellipsometrie. Die Mikroellipsometrie ist ein fokussierendes Ellipsometer, das aus der Polarisationsänderung, bedingt durch die Wechselwirkung Licht – Materie, die materialcharakteristische komplexe Brechzahl eines reflektierenden Materials ermitteln kann. Bei der fokussierenden Ellipsometrie ist die Anordnung der fokussierenden Optiken von Bedeutung. Die hier vorgestellte ellipsometerexterne Fokussierung vermeidet Messfehler durch optische Anisotropien und ermöglicht die multispektrale ellipsometrische Messung. Für die ellipsometrische Brechzahlbestimmung ist zwingend die Kenntnis des Einfallswinkels des Messstrahls und die räumliche Orientierung der Oberflächenneigung zum Koordinatensystem des Ellipsometers notwendig. Die Oberflächenneigung wird mit einem Deflektometer ermittelt, das speziell für den Einsatz in Kombination mit der Ellipsometrie entwickelt wurde. Aus der lokalen Oberflächenneigung kann die Topographie einer Probe rekonstruiert werden. Der Einfallswinkel ist ebenfalls aus den Oberflächenneigungen ableitbar. Die Arbeit stellt die Systemtheorie der beiden kombinierten Messverfahren vor, außerdem werden Beiträge zu Messunsicherheiten diskutiert. Der experimentelle Teil der Arbeit beinhaltet die separate Untersuchung zur Leistungsfähigkeit der beiden zu kombinierenden Messverfahren. Die experimentellen Ergebnisse erlauben die Schlussfolgerung, dass ein Mikro-Deflexions-Ellipsometer erfolgreich realisierbar ist.

Biofilmbildung bei Pflanzen-assoziierten Bakterien der Gattung Methylobacterium und molekulargenetisch-physiologische Charakterisierung eines neuen Marchantia-Isolats (Mtb. sp. JT1)

Bakterien existieren bevorzugt in Biofilmen. Das Zusammenleben in diesen Gemeinschaften bietet den einzelnen Mikroben einen wirksamen Schutz und ermöglicht die Ausbildung langfristiger, synergistischer Wechselwirkungen, die mit multizellulären Systemen verglichen werden können. Biofilme bestehen aus Mikrooganismen-Populationen, die sich an Grenzflächen ansammeln und typischerweise von einer Matrix aus extrazellulären polymeren Substanzen umgeben sind. Auch auf Pflanzen-Oberflächen bilden viele Bakterien Biofilme, um ihre Überlebenswahrscheinlichkeit zu erhöhen. In dieser Arbeit wurde die Biofilmbildung bei Pflanzen-assoziierten Bakterien der Gattung Methylobacterium (Mtb.) untersucht, wobei molekular- und mikrobiologische sowie mikroskopische Techniken eingesetzt wurden. Es zeigte sich, dass alle untersuchten Vertreter der Gattung Methylobacterium in unterschiedlichem Ausmaß Biofilme bilden. Die Ausprägung ist dabei Taxon (bzw. Isolat)-spezifisch und vor allem von der Stickstoff-Verfügbarkeit abhängig. Jedoch spielen auch andere Umweltfaktoren, wie die Versorgung der Zellen mit Phosphat und die Zelldichte, bei der Ausbildung der überzellulären Einheiten eine wichtige Rolle. Die Matrix der Biofilme wird meist durch ein fibrilläres Netzwerk gebildet. Dabei handelt es sich um Heteropolysaccharide, die von den Bakterien synthetisiert und sezerniert werden. Einige Isolate bilden zusätzlich zahlreiche Fimbrien (Auswüchse), durch die sie an andere Zellen oder Oberflächen binden können. Im zweiten Teil dieser Arbeit wurden mehrere neue Methylobacterium-Isolate physiologisch und molekulargenetisch charakterisiert (Nährstoffverwertung, DNA-Sequenzen verschiedener Gene, phylogenetische Analysen usw.). Im Vordergrund stand hierbei der von einer urtümlichen Landpflanze, dem Lebermoos (Marchantia polymorpha), isolierte Stamm Mtb. sp. JT1. Dabei zeigten sich deutliche Unterschiede in der Morphologie und Physiologie des Bakterienstamms JT1 und dem nahe verwandten Stamm 5b.2.20 zu den bereits beschriebenen Taxa der Gattung, so dass eine Spezies-Neubeschreibung erforderlich war. Als Artname wurde aufgrund der außergewöhnlichen Oberflächenstrukturen Mtb. fimbriae sp. nov. eingeführt. Auch andere Methylobakterien (unter anderem Isolat Mtb. sp. F3.2, isoliert vom Laubmoos Funaria hygrometrica) stellen wahrscheinlich Vertreter einer neue Spezies dar (Artname Mtb. funariae sp. nov.). Jedoch zeigen Mtb. fimbriae und Mtb. funariae nur geringe physiologische und morphologische Unterschiede und konnten auf Grundlage umfassender DNA-DNA-Hybridisierungs-Studien nicht eindeutig voneinander abgegrenzt werden.

Bestimmung der magnetischen Streufeldstärke von künstlichen magnetischen Domänen austauschverschobener Dünnschichtsysteme und deren Einfluss auf die Selbstassemblierung organischer Moleküle

Die lokale Anlagerung molekularer Substanzen auf Oberflächen ist technologisch von großem Interesse. Die Beeinflussung selbstassemblierender Materialien bietet dabei große Vorteile, da sie kostengünstig und großflächig angewendet werden kann. Untersuchungen einer solchen Beeinflussung mithilfe von magnetischen Feldern wurden bisher jedoch noch nicht durchgeführt. Ursache hierfür ist das, insbesondere bei der Verwendung von diamagnetischen Substanzen, geringe induzierte magnetische Moment und die daraus resultierenden geringen magnetischen Kräfte. In der vorliegenden Arbeit wurde untersucht, ob es möglich ist, die lokale Anlagerung von selbstassemblierenden, diamagnetischen Substanzen durch die Verwendung von magnetischen Streufeldern zu beeinflussen und somit ein Schichtwachstum bevorzugt in gewünschten Bereichen eines Substrats zu erreichen. Es wurde ein austauschverschobenes Dünnschichtsystem über das Verfahren der ionenbeschuss-induzierten magnetischen Strukturierung mit einem künstlichen Domänenmuster in streifenförmiger Anordnung im Mikrometermaßstab erzeugt. Über experimentelle Untersuchungen wurden die aus diesem Schichtsystem austretenden magnetischen Streufelder erstmals quantifiziert. Die experimentell unvermeidbaren Mittelungen und technischen Limitierungen wurden mithilfe eines theoretischen Modells herausgerechnet, sodass letztlich die resultierende Magnetfeldlandschaft in allen drei Dimensionen über der Probenoberfläche erhalten wurde. Durch die Bestimmung der magnetischen Suszeptibilitäten der hier verwendeten thioethersubstituierten Subphthalocyanin-Derivate konnte somit die Berechnung der induzierten magnetischen Kräfte erfolgen, deren Vergleich mit Literaturwerten eine erfolgreiche Beeinflussung der Anlagerung dieser Substanzen erhoffen ließ. Aufgrund der Kombination diverser, anspruchsvoller Nachweisverfahren konnte der experimentelle Beweis für die erfolgreiche Positionierung der molekularen Substanzen durch die magnetischen Streufelder des Dünnschichtsystems erbracht werden. Zunächst wurde nachgewiesen, dass sich die Subphthalocyanin-Derivate auf der Probenoberfläche befinden und in einer mit der Periode der magnetischen Domänenstruktur korrelierenden Geometrie anlagern. Über Untersuchungen an Synchrotronstrahlungsquellen konnte die magnetische Streifenstruktur mit der Struktur der angelagerten Moleküle überlagert werden, sodass bekannt wurde, dass sich die Moleküle bevorzugt in den magnetisch begünstigten Bereichen anlagern. Um mögliche Einflüsse einer eventuell durch den magnetischen Strukturierungsprozess lokal modifizierten Substratoberfläche als Ursache für die lokale Molekülanlagerung ausschließen zu können, wurden zusätzliche Referenzmessungen durchgeführt. Alle Untersuchungen zeigen, dass die Molekülpositionierung auf der Wechselwirkung der diamagnetischen Substanzen mit den Streufeldern des Substrats zurückzuführen ist. Der im Rahmen dieser Arbeit entwickelte Mechanismus der magnetischen Beeinflussung der lokalen Molekülanlagerung besagt dabei, dass insbesondere die Oberflächendiffusion der selbstassemblierenden Substanz durch die in-plane-Magnetfeldkomponente beeinflusst wird und vermutlich die Nukleationsphase der Selbstassemblierung entscheidend für die lokale Materialabscheidung ist. Es konnte in dieser Arbeit somit gezeigt werden, dass eine Beeinflussung der Selbstassemblierung von diamagnetischen Subphthalocyanin-Derivaten und somit eine lokal bevorzugte Anlagerung dieser Substanzen durch magnetische Streufelder von magnetisch strukturierten austauschverschobenen Dünnschichtsystemen erreicht werden kann. Es resultiert somit eine neue Möglichkeit die technologisch wichtigen Selbstassemblierungsprozesse nun auch über magnetische Streufelder beeinflussen und kontrollieren zu können. Durch die hohe Flexibilität bei den Strukturierungsmöglichkeiten der magnetischen Domänengeometrien der hier verwendeten austauschverschobenen Dünnschichtsysteme resultieren aus den hier gezeigten Ergebnissen vielfältige Anwendungsmöglichkeiten im Bereich der Beschichtungstechnik.

Comprehension of wh-questions and declarative sentences in agrammatic aphasia: the set partition hypothesis

Problematic trace-antecedent relations between deep and surface structure have been a dominant theme in sentence comprehension in agrammatism. We challenge this view and propose that the comprehension in agrammatism in declarative sentences and wh-questions stems from impaired processing in logical form. We present new data from wh-questions and declarative sentences and advance a new hypothesis which we call the set partition hypothesis. We argue that elements that signal set partition operations influence sentence comprehension while trace-antecedent relations remain intact. (C) 2007 Elsevier Ltd. All rights reserved.

Highly proton-ordered water structures on oxygen precovered Ru{0001}

We present helium scattering measurements of a water ad-layer grown on a O(2 1)/Ru(0001) surface. The adsorbed water layer results in a well ordered helium diffraction pattern with systematic extinctions of diffraction spots due to glide line symmetries. The data reflects a well-defined surface structure that maintains proton order even at surprisingly high temperatures of 140 K. The diffraction data we measure is consistent with a structure recently derived from STM measurements performed at 6 K. Comparison with recent DFT calculation is in partial agreement, suggesting that these calculations might be underestimating the contribution of relative water molecule orientations to the binding energy.

Assessing the microbial oxidative stress mechanism of ozone treatment through the responses of Escherichia coli mutants

Aims: To investigate the effect of the oxidative stress of ozone on the microbial inactivation, cell membrane integrity and permeability and morphology changes of Escherichia coli. Methods and Results: Escherichia coli BW 25113 and its isogenic mutants in soxR, soxS, oxyR, rpoS and dnaK genes were treated with ozone at a concentration of 6 lg ml)1 for a period up to 240 s. A significant effect of ozone exposure on microbial inactivation was observed. After ozonation, minor effects on the cell membrane integrity and permeability were observed, while scanning electron microscopy analysis showed slightly altered cell surface structure. Conclusions: The results of this study suggest that cell lysis was not the major mechanism of microbial inactivation. The deletion of oxidative stress–related genes resulted in increased susceptibility of E. coli cells to ozone treatment, implying that they play an important role for protection against the radicals produced by ozone. However, DnaK that has previously been shown to protect against oxidative stress did not protect against ozone treatment in this study. Furthermore, RpoS was important for the survival against ozone. Significance and Impact of the Study: This study provides important information about the role of oxidative stress in the responses of E. coli during ozonation.

Late-Holocene changes in character and behaviour of land-terminating glaciers on James Ross Island, Antarctica

Virtually no information is available on the response of land-terminating Antarctic Peninsula glaciers to climate change on a centennial timescale. This paper analyses the topography, geomorphology and sedimentology of prominent moraines on James Ross Island, Antarctica, to determine geometric changes and to interpret glacier behaviour. The moraines are very likely due to a late-Holocene phase of advance and featured (1) shearing and thrusting within the snout, (2) shearing and deformation of basal sediment, (3) more supraglacial debris than at present and (4) short distances of sediment transport. Retreat of ∼100 m and thinning of 15–20 m has produced a loss of 0.1 km3 of ice. The pattern of surface lowering is asymmetric. These geometrical changes are suggested most simply to be due to a net negative mass balance caused by a drier climate. Comparisons of the moraines with the current glaciological surface structure of the glaciers permits speculation of a transition from a polythermal to a cold-based thermal regime. Small land-terminating glaciers in the northern Antarctic Peninsula region could be cooling despite a warming climate.

Processing of zero-derived words in English: an fMRI investigation

Derivational morphological processes allow us to create new words (e.g. punish (V) to noun (N) punishment) from base forms. The number of steps from the basic units to derived words often varies (e.g., nationalitysurface form. It is therefore unclear whether the effects reported are attributable to underlying morphological complexity or to the processing of multiple surface morphemes. Here we report the first study to investigate morphological processing where derivational steps are not overtly marked (e.g., bridge-N>bridge-V) i.e., zero-derivation ( Aronoff, 1980). We compared the processing of one-step (soakingsurface derived -ing forms can be contextually participles, gerunds, or even nouns, they are all derived from verbs since the suffix -ing can only be attached to verb roots. Crucially, the verb root is the basic form for the one-step words, whereas for the two-step words the verb root is zero derived from a basic noun. Significantly increased brain activity was observed for complex (one-step and two-step) versus simple (zero-step) forms in regions involved in morphological processing, such as the left inferior frontal gyrus (LIFG). Critically, activation was also more pronounced for two-step compared to one-step forms. Since both types of derived words have the same surface structure, our findings suggest that morphological processing is based on underlying morphological complexity, independent of overt affixation. This study is the first to provide evidence for the processing of zero derivation, and demonstrates that morphological processing cannot be reduced to surface form-based segmentation.

Scale architecture of the palmar and plantar epidermis of Polychrus acutirostris Spix, 1825 (Iguania, Polychrotidae) and its relationship to arboreal locomotion

In tetrapod squamates, the diversity of micro-ornamentations of the epidermis of the contact areas of hands and feet is generally associated with constraints and modalities related to locomotion. Polychrus acutirostris is a medium-sized lizard that occurs in open heterogeneous habitats in South America, such as the cerrados, caatingas, and fallow lands. It progresses slowly on branches of various diameters in its arboreal environment. It can also move more rapidly on the ground. The hands and feet are prehensile and may be considered an adaptation for grasping and climbing. Epidermal surfaces from the palmar and plantar areas of the hands and feet of P. acutirostris were prepared for SEM examination, and studied at various magnifications. They show three major levels of complexity: (1) scale types, organized in gradients of size and imbrication, (2) scalar ornamentations, organized by increasing complexity and polarity, and (3) presence of Oberhautchen showing typically iguanian honeycomb micro-ornamentations. The shape and surface structure of the scales with their pattern of micro-ornamental peaks, which improve grip, and the grasping hands and feet indicate that P. acutirostris is morpho-functionally specialized for arboreality. (C) 2009 Elsevier GmbH. All rights reserved.

Chemical bonding and composition of silicon nitride films prepared by inductively coupled plasma chemical vapor deposition

Thin silicon nitride films were prepared at 350 degrees C by inductively coupled plasma chemical vapor deposition on Si(100) substrates under different NH(3)/SiH(4) or N(2)/SiH(4) gas mixture. The chemical composition and bonding structure of the deposited films were investigated as a function of the process parameters, such as the gas flow ratio NH(3)/SiH(4) or N(2)/SiH(4) and the RF power, using X-ray photoelectron spectroscopy (XPS). The gas flow ratio was 1.4, 4.3, 7.2 or 9.5 and the RF power, 50 or 100 W. Decomposition results of Si 2p XPS spectra indicated the presence of bulk Si, under-stoichiometric nitride, stoichiometric nitride Si(3)N(4), oxynitride SiN(x)O(y), and stoichiometric oxide SiO(2), and the amounts of these compounds were strongly influenced by the two process parameters. These results were consistent with those obtained from N 1s XPS spectra. The chemical composition ratio N/Si in the film increased with increasing the gas flow ratio until the gas flow ratio reached 4.3, reflecting the high reactivity of nitrogen, and stayed almost constant for further increase in gas flow ratio, the excess nitrogen being rejected from the growing film. A considerable and unexpected incorporation of contaminant oxygen and carbon into the depositing film was observed and attributed to their high chemical reactivity. (C) 2010 Elsevier B.V. All rights reserved.

Nitrate reduction on Pt single crystals with Pd multilayer

Nitrate reduction on palladium multilayers deposited on platinum single crystal electrodes was studied by cyclic voltammetry and FTIR spectroscopy in acid and alkaline media. The results are compared with those obtained with bulk palladium single crystals. The reaction is sensitive to the electrode surface structure, the reactivity depending on the solution pH. In acid solution nitrate was reduced at potentials below the potential of zero total charge (pztc), when the electrode is negatively charged. Competition between nitrate, hydrogen and anion adsorption and NO formation and accumulation at the surface are proposed as the main reasons for the slow reaction rate. On the bulk palladium single crystal electrodes, NO formation leads to a fast blockage of the surface resulting in a very low activity for nitrate reduction. In alkaline solution, nitrate is reduced at more positive potentials with significantly higher current being measured on the Pd multilayer on Pt(100) electrode. (C) 2008 Elsevier Ltd. All rights reserved.