Performance enhancement of a wideband spiral antenna using a stepped ground plane

This study presents the use of a stepped ground plane as a means to increase the gain and front-to-back ratio of an Archimedean spiral which operates in the frequency range 3–10 GHz. The backing structure is designed to optimize the antenna performance in discrete 1 GHz bands by placing each of the eight metal steps one quarter wavelength below the corresponding active regions of the spiral. Simulated and experimental results show that this type of ground plane can be designed to enhance the antenna performance over the entire 105% operating bandwidth of the spiral.

Selective High Impedance Surface Active Region Loading of Archimedean Spiral Antenna

We show that a significant increase in the gain and front-to-back ratio is obtained when different high impedance surface (HIS) sections are placed below the active regions of an Archimedean spiral antenna. The principle of operation is demonstrated at 3, 6, and 9 GHz for an antenna design that employs a ground plane composed of two dissimilar HISs. The unit cells of the HISs are collocated and resonant at the same frequency as the 3- and 6-GHz active regions of the wideband spiral. It is shown that the former HIS must also be designed to resonate at 9 GHz to avoid the generation of a boresight null that occurs because the structure is physically large enough to support higher-order modes. The improvement that is obtained at each of the three frequencies investigated is shown by comparing the predicted and measured radiation patterns for the free space and HIS-backed antenna.

Voltage Controlled Intertwined Spiral Arrays for Reconfigurable Metasurfaces

Reconfigurable bistate metasurfaces composed of interwoven spiral arrays with embedded pin diodes are proposed for single and dual polarisation operation. The switching capability is enabled by pin diodes that change the array response between transmission and reflection modes at the specified frequencies. The spiral conductors forming the metasurface also supply the dc bias for controlling pin diodes, thus avoiding the need of additional bias circuitry that can cause parasitic interference and affect the metasurface response. The simulation results show that proposed active metasurfaces exhibit good isolation between transmission and reflection states, while retaining excellent angular and polarisation stability with the large fractional bandwidth (FBW) inherent to the original passive arrays. © 2014 A. Vallecchi et al.

Reconfigurable frequency selective surfaces with interleaved spiral slots

A new type of active frequency selective surface (AFSS) is proposed to realise a voltage controlled bi-state (transparent and reflecting) response at the specified frequencies. The bi-state switching is achieved by combining a passive array of interleaved spiral slots in conducting screens and active dipole arrays with integrated pin diodes at the opposite sides of a thin dielectric substrate. Simulation results show that such active surfaces have high isolation between the transparency and reflection states, while retaining the merits of substantially sub-wavelength response of the unit cell and large fractional bandwidths (FBWs) inherent to the original passive interwoven spiral arrays. Potential applications include reconfigurable and controllable electromagnetic architecture of buildings.

Analytical model of interwoven spiral arrays

Interweaving planar spiral conductors in doubly periodic arrays enable substantially sub-wavelength resonant response along with broadening fractional bandwidth. A self-contained analytical model is proposed to accurately predict the characteristics of the intertwined quadrifilar spiral array near the fundamental resonance. The model, based upon a multiconductor transmission line (MTL) approach, provides physical insight into the unique properties of the distributed interactions between the interleaved counter-wound spiral arms extended beyond a single unit cell and elucidates the mechanisms underlying the array performance at normal and oblique incidence of TE and TM polarised waves. The developed MTL model is instrumental in the design of the artificial surfaces with the specified response.

Active singly and dual polarised interwoven spiral frequency selective surfaces

Reconfigurable bi-state interwoven spiral FSSs are explored in this work. Their switching capability is realized by pin diodes that enable the change of the electromagnetic response between transparent and reflecting modes at the specified frequencies in both singly and dual polarised unit cell configurations. The proposed topologies are single layer FSS with their elements acting also as dc current carrying conductors supplying the bias signal for switching pin diodes between the on and off states, thus avoiding the need of external bias lines that can cause parasitic resonances and affect the response at oblique incidence. The presented simulation results show that such active FSSs have potentially good isolation between the transmission and reflection states, while retaining the substantially subwavelength response of the unit cell with large fractional bandwidths (FBWs) inherent to the original passive FSSs.

Interwoven spiral arrays on ferrite-dielectric substrates for high-impedance metasurfaces

A high impedance metasurface (HIMS) composed of the arrays of intertwined planar spirals on thin (~0.1λ) ferrite-dielectric substrate is proposed. The HIMS exhibits fractional bandwidth in excess of 10% and excellent angular and polarisation stability of the circular polarised waves at oblique incidence.

Performance of Archimedean spiral antenna backed by FSS reflector

The use of a backing cavity composed of a frequency selective surface (FSS) above a metal plate as a means to suppress the back lobe radiation and increase the gain of an Archimedean spiral antenna that operates from 3 to 10 GHz is investigated. The FSS is designed to reflect signals in the upper band (7-10 GHz) with a loss of <;0.25 dB, and allow transmission in the lower band (3-6 GHz). Good impedance match and bidirectional to unidirectional beam transformation is obtained when the FSS and metal plate are inserted at a distance λ/4 below the spiral at the centre of the upper and lower bands, respectively. Simulated and measured radiation patterns are employed to show the performance enhancement, which is attributed to the FSS reflector.

Tri-Band HIS Backed Spiral Antenna for Wireless LAN Applications

This study reports the performance of an Archimedean spiral antenna, which exhibits unidirectional circularly polarized radiation patterns with a peak gain >8 dBic in the lower (2.4–2.485 GHz) and upper (5.15–5.35 and 5.725–5.875 GHz) Wireless local area network frequency bands. The required backlobe suppression and impedance match are obtained by placing a multiresonant high impedance surface (HIS) in close proximity to the radiating aperture. Simulated and measured radiation patterns are shown at the center frequency of all three channels and a comparison of the key performance metrics is made with free space and metal backed antenna arrangements to demonstrate the enhancements which are attributed to the HIS reflector.

Caught in a 'spiral': barriers to healthy eating and dietary health promotion needs from the perspective of unemployed young people and their service providers

The number of young people in Europe who are not in education, employment or training (NEET) is increasing. Given that young people from disadvantaged backgrounds tend to have diets of poor nutritional quality, this exploratory study sought to understand barriers and facilitators to healthy eating and dietary health promotion needs of unemployed young people aged 16-20 years. Three focus group discussions were held with young people (n=14). Six individual interviews and one paired interview with service providers (n=7). Data were recorded, transcribed verbatim and thematically content analysed. Themes were then fitted to social cognitive theory (SCT). Despite understanding of the principles of healthy eating, a ‘spiral’ of interrelated social, economic and associated psychological problems was perceived to render food and health of little value and low priority for the young people. The story related by the young people and corroborated by the service providers was of a lack of personal and vicarious experience with food. External, environmental factors such as the proliferation and proximity of fast food outlets and the high perceived cost of ‘healthy’ compared to ‘junk’ food rendered the young people low in self-efficacy and perceived control to make healthier food choices. Agency was instead expressed through consumption of junk food and substance abuse. Both the young people and service providers agreed that for dietary health promotion efforts to succeed, social problems needed addressed and agency encouraged through (individual and collective) active engagement of the young people themselves.

Conical Horn Antenna with Spiral Phase Plate for Difference Pattern Generation

This paper describes the performance characteristics and experimental validation of a compact conical horn antenna with a dielectric cylinder spiral phase plate attached at its aperture. This performs the function of a spatial phase imprinting device creating a helical wave-front which results in a null in the far field radiation pattern of the antenna assembly.

Split Ring FSS Reflectarray with Spiral Phase Distribution

The paper reports of a flat spiral phase plate structure based on reflectarray frequency selective surface, FSS, technology for the generation of helical far-field radiation patterns with circular polarization (CP) properties. Double split ring slot FSS is used as a means for adjusting the phase across the reflectarray. Simulations presented demonstrate generation of reflected helical beams at 10 GHz for CP wave incident on the structure. The far-field measurements are in a good agreement with the simulations and demonstrate a null of -11dB in the centre of the radiation pattern attributed to the helical wavefront.

Investigations on Metamaterial Based Spiral Inductors for Compact Microwave Devices

Division of Electronics Engineering