Single phase a-plane MgZnO epilayers for UV optoelectronics: substitutional behaviour of Mg at large contents

High quality 1 μm thick a-plane MgxZn1−xO layers were produced by molecular beam epitaxy with Mg contents higher than 50%. Resonant Rutherford backscattering spectrometry combined with ion channeling revealed a uniform growth in both composition and atomic order. The lattice-site location of Mg, Zn and O elements was determined independently, proving the substitutional behaviour of Mg in Zn-sites of the wurtzite lattice. X-Ray diffraction pole figure analysis also confirms the absence of phase separation. Optical properties at such high Mg contents were studied in Schottky photodiodes.

Current Mode with RMS Voltage and Offset Control Loops for a Single-Phase Aircraft Inverter Suitable for Parallel and 3-Phase Operation Modes

Rms voltage regulation may be an attractive possibility for controlling power inverters. Combined with a Hall Effect sensor for current control, it keeps its parallel operation capability while increasing its noise immunity, which may lead to a reduction of the Total Harmonic Distortion (THD). Besides, as voltage regulation is designed in DC, a simple PI regulator can provide accurate voltage tracking. Nevertheless, this approach does not lack drawbacks. Its narrow voltage bandwidth makes transients last longer and it increases the voltage THD when feeding non-linear loads, such as rectifying stages. On the other hand, the implementation can fall into offset voltage error. Furthermore, the information of the output voltage phase is hidden for the control as well, making the synchronization of a 3-phase setup not trivial. This paper explains the concept, design and implementation of the whole control scheme, in an on board inverter able to run in parallel and within a 3-phase setup. Special attention is paid to solve the problems foreseen at implementation level: a third analog loop accounts for the offset level is added and a digital algorithm guarantees 3-phase voltage synchronization.

Three phase system for statewide evaluation of occupational education programs : team leader handbook.

Cover title.

Operator's, organizational, direct support and general support maintenance manual : air conditioner, horizontal, compact, 9,000 Btu/hr, 115 volt, single phase 50/60 hertz, model A9KH-115P, NSN 4120-01-136-2214.

"31 October 1986."

Organizational maintenance repair parts and special tools list : air conditioning units, electric motor driven, 9,000 Btu/hr, vertical compact, 115 volt, single phase, 50/60 cycle (Therm-Air Manufacturing Co. model CV-9-1-15-60) FSN 4120-935-1609; 9,000 Btu/hr, vertical compact, 230 volt, three phase, 50/60 cycle ....

"February 1970."

Organizational maintenance repair parts and special tools list : air conditioner, vertical, compact, self-contained, air cooled, electric motor driven, 115 volts, A.C. 50/60 hertz, single phase, 9,000 Btu/hr cooling, 6,000 Btu/hr heating (Harvey W. Hottel model CV-9-5/6-15), FSN 4120-935-1609.

"September 1974."

Operators, organizational, direct support, and general support maintenance manual : water purification unit, 420 gallons per hour, electric driven, 115V, single phase, 60 hertz 1/20 to 1 1/4 hp (Litton Systems, Inc. model LPU 420-1), FSN 4610-012-5490.

"1 October 1969"--P. i.

Operator's manual : grinding kit, valve seat, electric 35 degree angle type concentric drive, 1/4 horsepower, AC/DC, single phase, 115-volt, 14000 RPM rated no load speed (K.O. Lee Company model P300BB) (4910-060-9983) and (K.O. Lee Company model P300BB-M2) (4910-473-6437).

"February 1965."

Operator and organizational maintenance manual (including repair parts and special tool lists) : tester, engine distributor, bench type, 6, 12, and 24-volt distributors, single-phase, 60-cycle, 115-volt (Heyer Products Company Inc., model 168) (4910-392-2939).

"30 September 1963."

Operator's, manual : milling machine, ram type, swivel head, plain table, power feed, 1 1/2 horsepower, 110-volt, 60-cycle, single-phase (Van Norman Machine Company models IR-3-22 and IRQ-3-22) (3417-624-4254).

"March 1967."

Organizational maintenance manual (including repair parts and special tools lists) : milling-grinding-drilling-slotting attachment, 115/230-volt, 60-cycle, single-phase, 1/3 horsepower (Dumore Company model 827401) ...

"January 1965."

Organizational maintenance manual : lathe, engine, bench mounted, solid bed type, 10 inch swing, no. 2 Morse taper center, 1-3/8 spindle hole, 110-volts, 60 cycle, single phase 3/4-horsepower, w/Army dwg. no. 7550151 bench (standard-modern tool series 2,000 model, 11 inch) (3416-517-0955).

"November 1965."

Operator's manual : boring machine, engine cylinder, portable, 3 1/2 to 7 1/2 bore diameter, 18 inch depth of bore, 110-volt, 60-cycle, single-phase (Cedar Rapids Engineering Company model FL) (4910-223-9734).

"November 1965."

Operator's manual : grinding machine, machine tool attachment, internal and external grinding, 5" maximum external diameter wheel, 1/4" minimum internal diameter wheel, 4,600 to 42,400 rpm spindle speed, 1/2 hp, AC/DC, 115 V, 60-C, single phase (Dumore series 5) ...

"October 1967."

Operator's manual : grinding machine, valve face, bench mounting, 9/32 inch to 11/16 inch chuck, 0 to 45 degree valve, face angle adjustment, 115-volt, AC/DC, 60-cycle, single phase (Cedar Rapids model "KWIK-WAY" KK) (4910-540-4679).

"6 October 1967."