Evaluating Bucknell's Waste Stream

This thesis examines three questions regarding the content of Bucknell University‟s waste stream and the contributors to campus recycling and solid waste disposal. The first asks, “What does Bucknell‟s waste stream consist of?” To answer this question, I designed a campus-wide waste audit procedure that sampled one dumpster from each of the eleven „activity‟ types on campus in order to better understand Bucknell‟s waste composition. The audit was implemented during the Fall semester of the 2011-2012 school year. The waste from each dumpster was sorted into several recyclable and non-recyclable categories and then weighed individually. Results showed the Bison and Carpenter Shop dumpsters to contain the highest percentage of divertible materials (through recycling and/or composting). When extrapolated, results also showed the Dining Services buildings and Facilities buildings to be the most waste dense in terms of pounds of waste generated per square foot. The Bison also generated the most overall waste by weight. The average composition of all dumpsters revealed that organic waste composed 24% of all waste, 23% was non-recyclable paper, and 20% was non-recyclable plastic. It will be important to move forward using these results to help create effective waste programs that target the appropriate areas of concern. My second question asks, “What influences waste behavior to contribute to this „picture‟ of the waste stream?” To answer this question, I created a survey that was sent out to randomly selected sub-group of the university‟s three constituencies: students, faculty, and staff. The survey sought responses regarding each constituency‟s solid waste disposal and recycling behavior, attitudes toward recycling, and motivating factors for solid waste disposal behaviors across different sectors of the university. Using regression analysis, I found three statistically significant motivating factors that influence solid waste disposal behavior: knowledge and awareness, moral value, and social norms. I further examined how a person‟s characteristics associate to these motivating factors and found that one‟s position on campus proved a significant association. Consistently, faculty and staff were strongly influenced by the aforementioned motivating factors, while students‟ behavior was less influenced by them. This suggests that new waste programs should target students to help increase the influence of these motivators to improve the recycling rate and lower overall solid waste disposal on campus. After making overall conclusions regarding the waste audit and survey, I ask my third question, which inquires, “What actions can Bucknell take to increase recycling rates and decrease solid waste generation?” Bucknell currently features several recycling and waste minimization programs on campus. However, using results from the waste audit and campus survey, we can better understand what are the issues of the waste stream, how do we go about addressing these issues, and who needs to be addressed. I propose several suggestions for projects that future students may take on for summer or thesis research. Suggestions include targeting the appropriate categories of waste that occur most frequently in the waste stream, as well as the building types that have the highest waste density and potential recovery rates. Additionally, certain groups on campus should be targeted more directly than others, namely the student body, which demonstrates the lowest influence by motivators of recycling and waste behavior. Several variables were identified as significant motivators of waste and recycling behavior, and could be used as program tactics to encourage more effective behavior.

Legal Aspects which Implement Good Practice Measures in the Management of Construction and Demolition Waste

The construction industry, one of the most important ones in the development of a country, generates unavoidable impacts on the environment. The social demand towards greater respect for the environment is a high and general outcry. Therefore, the construction industry needs to reduce the impact it produces. Proper waste management is not enough; we must take a further step in environmental management, where new measures need to be introduced for the prevention at source, such as good practices to promote recycling. Following the amendment of the legal frame applicable to Construction and Demolition Waste (C&D waste), important developments have been incorporated in European and International laws, aiming to promote the culture of reusing and recycling. This change of mindset, that is progressively taking place in society, is allowing for the consideration of C&D waste no longer as an unusable waste, but as a reusable material. The main objective of the work presented in this paper is to enhance C&D waste management systems through the development of preventive measures during the construction process. These measures concern all the agents intervening in the construction process as only the personal implication of all of them can ensure an efficient management of the C&D waste generated. Finally, a model based on preventive measures achieves organizational cohesion between the different stages of the construction process, as well as promoting the conservation of raw materials through the use and waste minimization. All of these in order to achieve a C&D waste management system, whose primary goal is zero waste generation

Plaster reinforcement with fibers by mineral wool obtained from the recycle of construction and demolition waste

The use of mineral wool is becoming more widespread due to increased acoustic and thermal demands of Spanish Technical Building Code. This increase affects both in rehabilitation and new construction projects. Therefore, waste generation of this type of insulating material is having more importance. The main objective of this research is to study the possibility of recycling fiber obtained from mineral wool of the C&DW as an alternative material to chopped glass fibers that are currently used as reinforcing elements in the prefabricated plaster. To achieve this objective, series are made of plaster E-35 additived with rock wool residue and glass wool residue at different rates of addition. These series are repeated by changing the additive by E fiberglass (length of 25mm) to make a comparative analysis with respect to the series additived with mineral wool waste. All the series are subjected to the test to determine Shore C surface hardness and mechanical testing to determine the compressive and flexural strength. From the results it can be concluded that: with rock wool residue, increases Shore C hardness up to 15% with respect to the glass fiber and 9% with respect to the glass wool, with a percentage of addition 2%. With rock wool residue, weight is decreased by 5% with respect to the glass fiber and 4% with respect to the glass wool waste, with an addition percentage of 4%. For an addition rate of 4%, results in the flexural strength test with fiberglass are 85% higher than those obtained with glass wool residue. However, for a percentage of 1% addition, the results obtained with glass wool residue are 35% higher than those obtained with fiberglass. For an addition rate of 3% results in the compressive strength test with fiberglass are 54% lower than those obtained with rock wool waste and 70% lower than those obtained with glass wool waste. Comparing the two mineral wools, it can be concluded that up to 3% of the addition, the glass wool series results obtained are 10% higher than those additived with rock wool. However, higher percentages of addition show that the results obtained with rock wool are 35% higher than those obtained with glass wool. The general conclusion is that the series additived with mineral wool from C&DW show better results in tests than the ones used nowadays as plaster reinforcement.

Yield, nutrient utilization and soil properties in a melon crop amended with wine-distillery waste

In Spain, large quantities of wine are produced every year (3,339,700 tonnes in 2011) (FAO, 2011) with the consequent waste generation. During the winemaking process, solid residues like grape stalks are generated, as well as grape marc and wine lees as by-products. According to the Council Regulation (EC) 1493/1999 on the common organization of the wine market, by-products coming from the winery industry must be sent to alcohol-distilleries to generate exhausted grape marc and vinasses. With an adequate composting treatment, these wastes can be applied to soils as a source of nutrients and organic matter. A three-year field experiment (2011, 2012 and 2013) was carried out in Ciudad Real (central Spain) to study the effects of wine-distillery waste compost application in a melon crop (Cucumis melo L.). Melon crop has been traditionally cultivated in this area with high inputs of water and fertilizers, but no antecedents of application of winery wastes are known. In a randomized complete block design, four treatments were compared: three compost doses consisted of 6.7 (D1), 13.3 (D2) and 20 t compost ha-1 (D3), and a control treatment without compost addition (D0). The soil was a shallow sandy-loam (Petrocalcic Palexeralfs) with a depth of 0.60 m and a discontinuous petrocalcic horizon between 0.60 and 0.70 m, slightly basic (pH 8.4), poor in organic matter (0.24%), rich in potassium (410 ppm) and with a medium level of phosphorus (22.1 ppm). During each growing period four harvests were carried out and total and marketable yield (fruits weighting <1 kg or visually rotten were not considered), fruit average weight and fruit number per plant were determined. At the end of the crop cycle, four plants per treatment were sampled and the nutrient content (N, P and K) was determined. Soil samplings (0-30 cm depth) were carried before the application of compost and at the end of each growing season and available N and P, as well as exchangeable K content were analyzed. With this information, an integrated analysis was carried out with the aim to evaluate the suitability of this compost as organic amendment.

Effects of biochar prepared from organic waste on soil properties

Biochar is a carbon-rich solid obtained by the thermal decomposition of organic matter under a limited supply of oxygen and at relatively low temperatures. Biochar can be prepared from the pyrolysis of different organic feed- stocks, such as wood and biomass crops, agricultural by-products, different types of waste or paper industry waste materials . The pyrolysis procedure of waste, i.e. sewage sludge, has mainly two advantages, firstly, it removes pathogens from waste and, secondly, biochar can reduce the leaching of heavy metals present in raw sewage sludge. This trend of the use of waste material as feedstocks to the preparation of biochar is increasing in the last years due to industrial development and economic growth imply an increase in waste generation. The application of biochar may have positive effects on soil physical properties as water holding capacity and structure or on soil biological activity and soil quality. Also, biochar can be used to remove water pollutants and can be used in multiple ways in soil remediation due to its adsorption of pesticides or metals. Also, biochar contribute to carbon sequestration due to carbon stability of biochar materials. The objective of this presentation is to review the positive effects of the biochar prepared from organic waste on soil properties.

Estimation of computer waste quantities using forecasting techniques

Technology changes rapidly over years providing continuously more options for computer alternatives and making life easier for economic, intra-relation or any other transactions. However, the introduction of new technology “pushes” old Information and Communication Technology (ICT) products to non-use. E-waste is defined as the quantities of ICT products which are not in use and is bivariate function of the sold quantities, and the probability that specific computers quantity will be regarded as obsolete. In this paper, an e-waste generation model is presented, which is applied to the following regions: Western and Eastern Europe, Asia/Pacific, Japan/Australia/New Zealand, North and South America. Furthermore, cumulative computer sales were retrieved for selected countries of the regions so as to compute obsolete computer quantities. In order to provide robust results for the forecasted quantities, a selection of forecasting models, namely (i) Bass, (ii) Gompertz, (iii) Logistic, (iv) Trend model, (v) Level model, (vi) AutoRegressive Moving Average (ARMA), and (vii) Exponential Smoothing were applied, depicting for each country that model which would provide better results in terms of minimum error indices (Mean Absolute Error and Mean Square Error) for the in-sample estimation. As new technology does not diffuse in all the regions of the world with the same speed due to different socio-economic factors, the lifespan distribution, which provides the probability of a certain quantity of computers to be considered as obsolete, is not adequately modeled in the literature. The time horizon for the forecasted quantities is 2014-2030, while the results show a very sharp increase in the USA and United Kingdom, due to the fact of decreasing computer lifespan and increasing sales.

A globálisan növekvő hulladékmennyiség és a kezelésére irányuló nemzetközi törekvések (International efforts to cope with globally increasing waste amounts)

Sokoldalú nemzetközi megállapodások és programok foglalkoznak a hulladékok keletkezésének és az országhatárokon átterjedő hatásainak problémájával, a nemzetközi együttműködést szükségessé tevő megoldásokkal. A leginkább átfogó megközelítést a probléma hajtóerőinek szentelt globális programok tartalmazzák, de a fenntarthatóság alapelveire támaszkodó termelési eljárásokra és fogyasztási szokásokra, a zöld gazdaságra való áttérést szorgalmazó dokumentumok nem tartalmaznak számon kérhető kötelezettségeket. A konkrétabb hulladékkeletkezési és hatásterjedési ügyekben – mindenekelőtt a veszélyes hulladékok és a nemzeti fennhatóság alá nem tartozó területekre eljutó vagy ott keletkező hulladékok esetében – jóval konkrétabb nemzetközi megállapodások és programok léteznek. Ezek szabályozási, szakpolitikai, technológiai célokat, feladatokat határoznak meg az országok és az érintett ágazati szereplők szintjén is. Egyes problémák kapcsán és egyes térségekben a hulladékgazdálkodás jelentős eredményeket tud felmutatni, de általában véve a nemzetközi megállapodások hatékony végrehajtásával komoly gondok vannak. Továbbá a meglévő nemzetközi eszközök összességükben még teljes körű végrehajtásuk esetén sem lennének képesek ellensúlyozni a hulladékprobléma globális szintű növekedését. Következésképpen további erőfeszítésekre van szükség – minden kormány, érintett nem-kormányzati szervezet és az ágazatok részéről – különösen a megelőzés vonatkozásában. ____ Various multilateral agreements and programmes deal with the problems of waste generation and its transboundary impacts, and those solutions, which necessitate international co-operation. Those global programmes include the most comprehensive approach, which are dedicated to the drivers of these problems, however, these documents promoting the transition to sustainable production and consumption, or to the green economy do not consist of binding commitments. In case of more concrete issues of waste generation and transboundary impacts there are much more concrete international agreements and programmes, especially, for the hazardous waste streams and the waste transmitted to and/or generated in areas outside national jurisdiction. These determine regulatory, policy, technological goals and tasks for the participating countries and the relevant sectors. Significant progress is demonstrated for some specific problems and in certain regions, but in general, there are serious concerns about the efficient implementation of the international agreements in their entirety. Moreover, even if those were fully accomplished, the existing set of the international instruments would be unable to counterweigh the global increase of the waste problem. Consequently, further efforts are needed by all countries, the relevant non-governmental organisations and sectors, primarily in order to prevent the further global escalation of the problem.

Dissolution of a spatially variable DNAPL (dense non aqueous phase liquid) source

Dissolution of non-aqueous phase liquids (NAPLs) or gases into groundwater is a key process, both for contamination problems originating from organic liquid sources, and for dissolution trapping in geological storage of CO2. Dissolution in natural systems typically will involve both high and low NAPL saturations and a wide range of pore water flow velocities within the same source zone for dissolution to groundwater. To correctly predict dissolution in such complex systems and as the NAPL saturations change over time, models must be capable of predicting dissolution under a range of saturations and flow conditions. To provide data to test and validate such models, an experiment was conducted in a two-dimensional sand tank, where the dissolution of a spatially variable, 5x5 cm**2 DNAPL tetrachloroethene source was carefully measured using x-ray attenuation techniques at a resolution of 0.2x0.2 cm**2. By continuously measuring the NAPL saturations, the temporal evolution of DNAPL mass loss by dissolution to groundwater could be measured at each pixel. Next, a general dissolution and solute transport code was written and several published rate-limited (RL) dissolution models and a local equilibrium (LE) approach were tested against the experimental data. It was found that none of the models could adequately predict the observed dissolution pattern, particularly in the zones of higher NAPL saturation. Combining these models with a model for NAPL pool dissolution produced qualitatively better agreement with experimental data, but the total matching error was not significantly improved. A sensitivity study of commonly used fitting parameters further showed that several combinations of these parameters could produce equally good fits to the experimental observations. The results indicate that common empirical model formulations for RL dissolution may be inadequate in complex, variable saturation NAPL source zones, and that further model developments and testing is desirable.

An assessment of timber dwellings typical of the Queenslander era, and constraints associated with their relocation, component and adaptive reuse when considering 'regeneration'

This paper presents an explanation of why the reuse of building components after demolition or deconstruction is critical to the future of the construction industry. An examination of the historical cause and response to climate change sets the scene as to why governance is becoming increasingly focused on the built environment as a mechanism to controlling waste generation associated with the process of demolition, construction and operation. Through an annotated description to the evolving design and construction methodology of a range of timber dwellings (typically 'Queenslanders' during the eras of 1880-1900, 1900-1920 & 1920-1940) the paper offers an evaluation to the variety of materials, which can be used advantageously by those wishing to 'regenerate' a Queenslander. This analysis of 'regeneration' details the constraints when considering relocation and/ or reuse by adaption including deconstruction of building components against the legislative framework requirements of the Queensland Building Act 1975 and the Queensland Sustainable Planning Act 2009, with a specific examination to those of the Building Codes of Australia. The paper concludes with a discussion of these constraints, their impacts on 'regeneration' and the need for further research to seek greater understanding of the practicalities and drivers of relocation, adaptive and building components suitability for reuse after deconstruction.

Regeneration

This presentation relates to a paper presenting an explanation of why the reuse of building components after demolition or deconstruction is critical to the future of the construction industry. An examination of the historical cause and response to climate change sets the scene as to why governance is becoming increasingly focused on the built environment as a mechanism to controlling waste generation associated with the process of demolition, construction and operation. Through an annotated description to the evolving design and construction methodology of a range of timber dwellings (typically 'Queenslanders' during the eras of 1880-1900, 1900-1920 & 1920-1940) the paper offers an evaluation to the variety of materials, which can be used advantageously by those wishing to 'regenerate' a Queenslander. This analysis of 'regeneration' details the constraints when considering relocation and/ or reuse by adaption including deconstruction of building components against the legislative framework requirements of the Queensland Building Act 1975 and the Queensland Sustainable Planning Act 2009, with a specific examination to those of the Building Codes of Australia. The paper concludes with a discussion of these constraints, their impacts on 'regeneration' and the need for further research to seek greater understanding of the practicalities and drivers of relocation, adaptive and building components suitability for reuse after deconstruction.

Delphi study for improving sustainable construction project management in universities

As sustainability becomes an important principle guiding various human activities around the globe, the higher education sector is being asked to take an active part in educating and promoting sustainability due to its moral responsibility, social obligation and its own needs to adapt to new circumstances. There is a global trend of higher education institutions embarking on responses to the sustainability challenge. On-campus building performance is one of the most important indicators for “sustainable universities”, because buildings carry substantially environmental burden such as considerable consumption of raw materials and energy as well as huge amount of waste generation and greenhouse gas emission. Plus, much research proves that building performance can impact on students and staff’s awareness about and behaviours related to sustainability. The past studies rarely discussed about sustainable construction projects in universities’ unique context. Universities are labeled with distinct characteristics such as complex governance, multiple cultures and juggling missions and so on. It is necessary and meaningful to examine the project management system in terms of universities’ organizational environment. Thus, this research project applies Delphi study to identify primary barriers to green technology application in on-campus buildings, critical factors for sustainable project success, key actions in project phases and strategies for project improvement. Through three rounds of questionnaires among panel experts, the authors obtain a profound understanding of project delivery system in universities. The research results are expected to provide sustainability practitioners with holistic understanding and generic information about sustainable construction project performance on campus as an assistance tool.

Improving ecological performance of industrialized building systems in Malaysia

For construction stakeholders to fully embrace sustainability, its long-term benefits and associated risks need to be identified through holistic approaches. Consensus among key stakeholders is very important to the improvement of the ecological performance of industrialized building systems (IBS), a building construction method gaining momentum in Malaysia. A questionnaire survey examines the relative significance of 16 potentially important sustainability factors for IBS applications. To present possible solutions,semi-structured interviews solicit views from experienced IBS practitioners, representing the professions involved. Three most critical factors agreed by key stakeholders are material consumption, waste generation and waste disposal. Using SWOT analysis, the positive and negative aspects of these factors are investigated, with action plans formulated for IBS design practitioners. The SWOT analysis based guidelines have the potential to become part of IBS design briefing documents against which sustainability solutions are contemplated, selected and implemented. Existing knowledge on ecological performance issues is extended by considering the unique characteristics of IBS and identifying not only the benefits, but also the potential risks and challenges of pursuing sustainability. This is largely missing in previous research efforts. Findings to date focus on providing much-needed assistance to IBS designers, who are at the forefront of decision-making with a significant level of project influence. Ongoing work will be directed towards other project development phases and consider the inherent linkage between design decisions and subsequent sustainability deliverables in the project life cycle.

Coleta Seletiva Solidária de resíduos recicláveis dirigida à rede estadual de ensino do Rio de Janeiro - estudo de caso.

O aumento da demanda de água, energia, bem como a mudança na composição e na quantidade dos resíduos, associados aos impactos socioambientais que eles provocam, tornaram-se um dos grandes desafios atuais para a sociedade e, em particular, para as escolas públicas. Nesse contexto, o governo do estado do Rio de Janeiro, dentro de seu Plano Estadual de Gerenciamento Integrado de Resíduos Sólidos, criou o Programa Coleta Seletiva Solidária (PCSS), em outubro de 2009, realizado em parceria entre o Instituto Estadual do Ambiente (INEA), a Universidade do Estado do Rio de Janeiro (UERJ) e a Secretaria de Estado de Educação (SEEDUC). Este Programa assessora a implantação da Coleta Seletiva Solidária (CSS) de materiais recicláveis nos municípios do estado. O eixo-escolas, uma das suas linhas de ações, assessora a implantação da CSS na rede estadual, conforme determina o Decreto Estadual 40.645/07. Considerando os problemas relacionados aos resíduos e a exigência legal, boa parte das escolas estaduais não implantaram ainda a Coleta Seletiva Solidária, por diversos fatores. O objetivo da pesquisa é estudar o modelo de Coleta Seletiva proposto pelo PCSS nas escolas da rede estadual de ensino do Rio de Janeiro. Como estudo de caso, esse modelo foi aplicado no Colégio Estadual Souza Aguiar (CESA). Utilizou-se da pesquisa-ação como abordagem metodológica e o instrumento de coleta de dados foi o questionário dirigido aos participantes das oficinas de capacitação na UERJ. No CESA foram aplicados questionários aos alunos e acompanhado o processo de implantação da CSS através da observação participante. Conclui-se que os resultados da pesquisa não podem ser generalizados para toda a rede estadual de ensino do Rio de Janeiro. Contudo, ele possibilitou identificar questões importantes e sugerir recomendações para o aperfeiçoamento do modelo estudado. Destaca-se a importância de formalizar o compromisso institucional dos dirigentes das escolas com a implantação da CSS, contribuindo com a formação de cidadãos comprometidos com a sustentabilidade socioambiental do estado do Rio de Janeiro.

Sistema de Gerenciamento Integrado de resíduos perigosos: modelagem e validação nos laboratórios da Universidade do Estado do Rio de Janeiro

Apesar dos impactos ambientais ocasionados pela poluição e acidentes químicos, constata-se que algumas organizações ainda investem pouco na prevenção, redução ou eliminação de seus resíduos. Em algumas Instituições de Ensino e Pesquisa (IES) do Brasil, não é incomum o manejo inadequado dos resíduos perigosos gerados em laboratórios de ensino e pesquisa, aumentando tais riscos. Para minimizar ou eliminar tais riscos, há que se realizarem investimentos em processos tecnológicos de tratamento e na seleção de métodos adequados ao gerenciamento. O objetivo desta pesquisa foi modelar um Sistema de Gerenciamento Integrado de Resíduos Perigosos e validá-lo através de sua aplicação em estudo piloto nos laboratórios dos Institutos de Química e Biologia da Universidade do Estado do Rio de Janeiro. A pesquisa empírica e exploratória foi realizada através de revisão bibliográfica e coleta de dados sobre o estado da arte no gerenciamento de resíduos em algumas IES nacionais e internacionais, seguido da seleção do sistema adequado a ser modelado e aplicado nestes contextos. O trabalho de campo consistiu na coleta de dados através de observação direta e aplicação de questionário junto aos responsáveis pelos laboratórios. As etapas do estudo foram: levantamento das instalações dos laboratórios; observação do manejo e geração dos resíduos; elaboração do banco de dados; análise qualitativa e quantitativa dos dados; modelagem do Sistema de Gerenciamento Integrado de Resíduos Perigosos SIGIRPE; implantação do modelo; apresentação e avaliação dos resultados; elaboração do manual para uso do sistema. O monitoramento quantitativo de resíduos foi feito através de ferramentas do sistema para a sua análise temporal. Os resultados da pesquisa permitiram conhecer a dinâmica e os problemas existentes nos laboratórios, bem como verificar a potencialidade do modelo. Conclui-se que o SIGIRPE pode ser aplicado a outros contextos desde que seja adequado para tal fim. É imprescindível ter uma estrutura institucional que elabore o Plano de Gerenciamento Integrado de Resíduos e viabilize sua implementação. A universidade, enquanto formadora dos futuros profissionais, é um lócus privilegiado na construção e disseminação do conhecimento, tendo o dever de realizar boas práticas no trato das questões ambientais, em particular, com relação aos resíduos. Assim, elas devem estabelecer entre suas estratégias de ação, a inclusão de políticas ambientais em seus campi, onde a Educação Ambiental deve ser permanente. Espera-se que este trabalho contribua com o planejamento e o gerenciamento dos resíduos perigosos gerados em laboratórios e com as mudanças necessárias rumo à sustentabilidade ambiental. O SIGIRPE foi elaborado e testado, mas não foi possível verificar sua aplicação por outros usuários. É o que se espera com a continuidade desta pesquisa e no desenvolvimento de futuros trabalhos, tais como: teste do sistema em hospitais, laboratórios, clínicas; estudar outras aplicações na área de segurança química de laboratórios através da inclusão de roteiro de transporte interno de resíduos, rotas de fuga, mapas de risco, localização de equipamentos de proteção individual e coletiva; demonstrar a potencialidade de uso do sistema e sensibilizar os segmentos envolvidos através de palestras, mini-cursos e outras estratégias de informação em revistas científicas especializadas.

Proposta de construção de um indicador global para sustentabilidade ambiental do processo industrial numa empresa petroquímica instalada no estado do Rio de Janeiro

No presente trabalho foi realizada uma na pesquisa bibliográfica sobre indicadores globais para avaliação da eficiência de um sistema de gestão ambiental (SGA) e sobre o conceito de sustentabilidade ambiental, com o objetivo de estudar o SGA de uma empresa petroquímica, instalada no Rio de Janeiro, certificada pela ISO 9001, ISO 14001 e OSHA 18001. Procurou-se, assim, identificar, a partir da análise dos indicadores de avaliação do desempenho ambiental, a possibilidade de implantar um indicador único para avaliação da eficiência do SGA estudado, de forma a mostrar aos observadores externos e internos, o efetivo engajamento da empresa na preservação dos recursos naturais e na minimização das emissões atmosféricas e de gases de efeito estufa, dentro da ótica de sustentabilidade ambiental focando-se um processo produtivo industrial. Por meio da pesquisa, verificou-se que, apesar de a empresa utilizar indicadores relacionados com o consumo de água, de emissões fugitivas e de geração de resíduos, dentre outros, ela não monitora, de forma objetiva, as emissões em termos de CO2 equivalente e todas as ações ligadas à sustentabilidade ambiental. Assim, foi proposto um indicador global de sustentabilidade ambiental para ser utilizado como referência do processo produtivo, visando fornecer ao responsável pelo SGA os subsídios necessários para tratar da gestão do processo sob a ótica da sustentabilidade ambiental