A simultaneous voltammetric temperature and humidity sensor

We report the simultaneous measurement of temperature and humidity by analysing square wave voltammetric responses of two ferrocene derivatives, decamethylferrocene (DmFc) and 1,2-diferrocenylethylene (bisferrocene, BisFc) in 1-(2-methoxyethyl)-1-methyl-pyrrolidinium tris(pentafluoroethyl) trifluorophosphate ([Moepyrr][FAP]). These two molecules produce three peaks in square wave voltammetry. Through study of the peak potentials of BisFc/BisFc(+) (vs. DmFc/DmFc(+)) and BisFc(+)/BisFc(2+) (vs. DmFc/DmFc(+)) over a temperature range of 298 K to 318 K and humidity range of 1% to 50% using square wave voltammetry, the temperature and humidity dependences of the relative peak potentials were investigated. A reliable method to calculate the humidity and temperature based on the voltammetric experiment is characterised and demonstrated.

Liquid densities, heat capacities, refractive index and excess quantities for {protic ionic liquids plus water} binary system

Densities, rho, of aqueous solutions of the room temperature protic ionic liquid (PIL), pyrrolidinium nitrate are determined at the atmospheric pressure over the temperature range from (283.15 to 323.15) K and within the whole composition range. The molar isobaric heat capacities, C(p), and refractive index, n(D), of {PIL + water} binary system are measured at 298.15 K. The excess molar volumes V(E), excess molar isobaric heat capacities C(p)(E), and deviation from ideality of refractive index Delta(phi)n, of pyrrolidinium nitrate aqueous solutions were deduced from the experimental results as well as apparent molar volumes V(phi), partial molar volumes (V) over bar (m,i), and thermal expansion coefficients alpha(p). The V(E) values were found to be positive over the entire composition range at all temperatures studied therein, whereas deviations from ideality were negative for refractive index Delta(phi)n. The volumetric properties of binary mixtures containing water and four other protic ionic liquids, such as pyrrolidinium hydrogen sulfate, pyrrolidinium formiate, collidinium formate, and diisopropyl-ethylammonium formate were also determined at 298.15 K. Results have been then discussed in terms of molecular interactions and molecular structures in these binary mixtures. (C) 2009 Elsevier Ltd. All rights reserved.

Dynamics of excess electronic charge in aliphatic ionic liquids containing the bis(trifluoromethylsulfonyl)amide anion

In a recent article (J. Am. Chem. Soc. 2011, 133, 20186) we investigated the initial spatial distribution of dry excess electrons in a series of room-temperature ionic liquids (RTILs). Perhaps unexpectedly, we found that in some alkylammonium-based systems the excess negative charge resided on anions and not on the positive cations. Following on these results, in the current paper we describe the time evolution of an excess electronic charge introduced in alkylammonium- and pyrrolidinium-based ionic liquids coupled with the bis(trifluoromethylsulfonyl)amide ([TfN]) anion. We find that on a 50 fs time scale an initially delocalized excess electron localizes on a single [TfN] anion which begins a fragmentation process. Low-energy transitions have a very different physical origin on the several femtoseconds time scale when compared to what occurs on the picosecond time scale. At time zero, these are intraband transitions of the excess electron. However after 40 fs when the excess electronic charge localizes on a single anion, these transitions disappear, and the spectrum is dominated by electron-transfer transitions between the fragments of the doubly charged breaking anion. © 2013 American Chemical Society.

3-Methylpiperidinium ionic liquids

A wide range of room temperature ionic liquids based on the 3-methylpiperdinium cation core were produced from 3-methylpiperidine, which is a derivative of DYTEK® A amine. First, reaction with 1-bromoalkanes or 1-bromoalkoxyalkanes generated the corresponding tertiary amines (Rmβpip, R = alkyl or alkoxyalkyl); further quaternisation reactions with the appropriate methylating agents yielded the quaternary [Rmmβpip]X salts (X(-) = I(-), [CF3CO2](-) or [OTf](-); Tf = -SO2CF3), and [Rmmβpip][NTf2] were prepared by anion metathesis from the corresponding iodides. All [NTf2](-) salts are liquids at room temperature. [Rmmβpip]X (X(-) = I(-), [CF3CO2](-) or [OTf](-)) are low-melting solids when R = alkyl, but room temperature liquids upon introduction of ether functionalities on R. Neither of the 3-methylpiperdinium ionic liquids showed any signs of crystallisation, even well below 0 °C. Some related non-C-substituted piperidinium and pyrrolidinium analogues were prepared and studied for comparison. Crystal structures of 1-hexyl-1,3-dimethylpiperidinium tetraphenylborate, 1-butyl-3-methylpiperidinium bromide, 1-(2-methoxyethyl)-1-methylpiperidinium chloride and 1-(2-methoxyethyl)-1-methylpyrrolidinium bromide are reported. Extensive structural and physical data are collected and compared to literature data, with special emphasis on the systematic study of the cation ring size and/or asymmetry effects on density, viscosity and ionic conductivity, allowing general trends to be outlined. Cyclic voltammetry shows that 3-methylpiperidinium ionic liquids, similarly to azepanium, piperidinium or pyrrolidinium counterparts, are extremely electrochemically stable; the portfolio of useful alternatives for safe and high-performing electrolytes is thus greatly extended.

Efficient and selective hydrogen peroxide-mediated oxidation of sulfides in batch and segmented and continuous flow using a peroxometalate-based polymer immobilised ionic liquid phase catalyst

The peroxometalate-based polymer immobilized ionic liquid phase catalyst [PO4{WO(O-2)(2)}(4)]@PIILP has been prepared by anion exchange of ring opening metathesis-derived pyrrolidinium-decorated norbornene/ cyclooctene copolymer and shown to be a remarkably efficient system for the selective oxidation of sulfides under mild conditions. A cartridge packed with a mixture of [PO4{WO(O-2)(2)}(4)]@PIILP and silica operated as a segmented or continuous flow process and gave good conversions and high selectivity for either sulfoxide (92% in methanol at 96% conversion for a residence time of 4 min) or sulfone (96% in acetonitrile at 96% conversion for a residence time of 15 min). The immobilized catalyst remained active for 8 h under continuous flow operation with a stable activity/selectivity profile that allowed 6.5 g of reactant to be processed (TON = 46 428) while a single catalyst cartridge could be used for the consecutive oxidation of multiple substrates giving activity-selectivity profiles that matched those obtained with fresh catalyst.

Ionic liquid solvents of perhalide type for metals for extraction radioactive metals from mineral ores.

The invention relates to a process for dissolving metals (e.g., Al, Cu, Fe, Cr, Sb, Ti, and W) in perhalide contg. ionic liqs. having the formula (I), and to the extn. of metals from mineral ores; the remediation of materials contaminated with heavy, toxic, or radioactive metals; and to the removal of heavy and toxic metals from hydrocarbon streams. In the formula (I), [X] comprises at least one perhalide anion selected from [I3]-, [BrI2]-, [Br2I]-, [ClI2]-, [ClBr2]-, [BrCl2]-, or [ICl2]-, [ClI3]-. The (Cat+) is a cationic species selected from: ammonium, azaannulenium, azathiazolium, benzimidazolium, benzofuranium, benzotriazolium, borolium, cinnolinium, diazabicyclodecenium, diazabicyclononenium, diazabicyclo- undecenium, dithiazolium, furanium, guanidinium, imidazolium, indazolium, indolinium, indolium, morpholinium, oxaborolium, oxaphospholium, oxazinium, oxazolium, iso-oxazolium, oxathiazolium, pentazolium, phospholium, phosphonium, phthalazinium, piperazinium, piperidinium, pyranium, pyrazinium, pyrazolium, pyridazinium, pyridinium, pyrimidinium, pyrrolidinium, pyrrolium, quinazolinium, quinolinium, isoquinolinium, quinoxalinium, selenozolium, sulfonium, tetrazolium, iso-thiadiazolium, thiazinium, thiazolium, thiophenium, thiuronium, triazadecenium, triazinium, triazolium, iso-triazolium, and uronium. [on SciFinder(R)]

Electrostatic layer-by-layer deposition and electrochemical characterization of thin films composed of MnO(2) nanoparticles in a room-temperature ionic liquid

Thin films of MnO(2) nanoparticles were grown using the layer-by-layer method with poly (diallyldimetylammonium) as the intercalated layer. The film growth was followed by UV-vis, electrochemical quartz crystal microbalance (EQCM), and atomic force microscopy. Linear growth due to electrostatic immobilization of layers was observed up to 30 bilayers, but electrical connectivity was maintained only for 12 MnO(2)/PPDA bilayers. The electrochemical characterization of this film in 1-butyl-2,3-dimethyl-imidazolium (BMMI) bis(trifluoromethanesulfonyl)imide (TFSI) (BMMITFSI) with and without addition of a lithium salt indicated a higher electrochemical response of the nanostructured electrode in the lithium-containing electrolyte. On the basis of EQCM experiments, it was possible to confirm that the charge compensation process is achieved mainly by the TFSI anion at short times (<2 s) and by BMMI and lithium cations at longer times. The fact that large ions like TFSI and BMMI participate in the electroneutrality is attributed to the redox reaction that occurs at the superficial sites and to the high concentration of these species compared to that of lithium cations.

The 'filler-effect' in organic ionic plastic crystals : Enhanced conductivity by the addition of nano-sized TiO2

The addition of nano-sized ceramic particles to the plastic crystal ethyl-methyl pyrrolidinium bis(trifluoromethane sulfonyl)amide (P₁₂TFSA) has been investigated by means of DSC and conductivity. The thermal behaviour of the plastic crystal as a function of filler content suggests that the filler particles decrease the onset temperature of the melting slightly at high loadings, however they do not decrease the crystallinity of the material. Furthermore, the IV → III transition decreases in intensity, indicating that the addition of filler increases the possibility for the crystal to remain in metastable rotator phases also at lower temperatures. The conductivity shows a more than one order of magnitude increase with the addition of filler, with a filler concentration dependence that levels out above ~ 10 wt.% TiO₂.

Rotational and translational mobility of a highly plastic salt : Dimethylpyrrolidinium thiocyanate

Thermal analysis, impedance spectroscopy, NMR and Raman spectroscopy have been used to investigate the plastic crystal dimethylpyrrolidinium thiocyanate in order to gain further insight into the properties of organic ionic plastic crystals. This compound has a solid–solid phase transition at 82 °C, and melts at 122 °C. A step increase in conductivity of about one order of magnitude is observed at the phase transition, followed by a decrease in activation energy for conduction. A large entropy gain occurs at the II → I transition, and ¹H NMR linewidth measurements together with second moment calculations showed that the dimethylpyrrolidinium cation goes from a static state, to full isotropic tumbling. Raman measurements confirm that the cation as well as the anion exhibit increased rotational mobility when entering phase I.

Solid state ion transport and phase behaviour in composites of N,N-methyl propylpyrrolidinium tetrafluoroborate and amorphous polyethylene oxide

The binary and ternary addition of 2 wt.% LiBF₄ and 2 wt.% amorphous polyethylene oxide (aPEO) respectively to the plastic crystal forming salt P₁₃BF₄ (where P₁₃⁺=methylpropyl pyrrolidinium cation) was investigated with specific focus on the phase behaviour and evaluation of transport characteristics. Differential scanning calorimetry (DSC), optical thermomicroscopy, solid state nuclear magnetic resonance (NMR), and AC impedance spectroscopy were used to develop an understanding of the conduction process in the pure and mixed systems. The morphology of the ternary compound appeared as hexagonal spherulites upon solidification. Multinuclear NMR Pulsed Field Gradient measurements (¹H,¹⁹F,⁷Li) to probe both cation and anion diffusion coefficients are reported. The anion is shown to be the most diffusive (at 320 K:¹⁹F=2.5×10⁻¹¹ m² s⁻¹; 1H: 1.8×10⁻¹¹ m² s⁻¹; ⁷Li: 1.1×10⁻¹¹ m² s⁻¹) in the ternary compound, with enhanced conductivity (2.7×10⁻⁵ S cm⁻¹ at 310 K) just below the melt.

Transport and phase dynamics of poly(vinyl pyrrolidone) doped plastically crystalline N-methyl-N-propylpyrrolidinium tetrafluoroborate

The plastic crystal phase forming N-methyl-N-propylpyrrolidinium tetrafluoroborate organic salt (P₁₃BF₄) was combined with 2, 5 and 10 wt.% poly(vinyl pyrrolidone) (PVP). The ternary 2 wt.% PVP/2 wt.% LiBF₄/P₁₃BF₄ was also investigated. Thermal analysis, conductivity, optical thermomicroscopy, and Nuclear Magnetic Resonance (¹¹B, ¹⁹F, ¹H, ⁷Li) were used to probe the fundamental transport processes. Both the onset of phase I and the final melting temperature were reduced with increasing additions of PVP. Conductivity in phase I was 2.6 × 10^{− 4} S cm^{− 1} 5.2 × 10^{− 4} S cm^{− 1} 1.1 × 10^{− 4} S cm^{− 1} and 3.9 × 10− 5 S cm− 1 for 0, 2, 5 and 10 wt.%PVP/P₁₃BF₄, respectively. Doping with 2 wt.% LiBF₄ increased the conductivity by up to an order of magnitude in phase II. Further additions of 2 wt.% PVP slightly reduced the conductivity, although it remained higher than for pure P₁₃BF₄.

N-methyl-N-alkylpyrrolidinium tetrafluoroborate salts : ionic solvents and solid electrolytes

A series of N-methyl-N-alkylpyrrolidinium tetrafluoroborate salts were synthesised. The spectroscopic, physical and electrochemical characteristics of this family of salts have been investigated with respect to potential usage as ionic solvents and electrolytes. The lowest melting point among the family is 64°C for the N-methyl-N-propylpyrrolidinium tetrafluoroborate (P₁₃BF₄). This is sufficiently low to enable this salt to be useful as an ionic liquid in chemical synthesis involving reactions above 70°C. Most of the compounds exhibit one or more solid–solid transitions below the melting point, this behaviour is thought to indicate the existence of plastic crystal phases.

N-methyl-N-alkylpyrrolidinium bis(perfluoroethylsulfonyl)amide ([NPf2]–) and tris(trifluoromethanesulfonyl)methide ([CTf3]–) salts : synthesis and characterization

Novel salts based the pyrrolidinium cation [C_nmpyr]⁺ (where n denote the number of carbons in the straight alkyl chain) and either the [NPf₂]^– or [CTf₃]^– anions have been synthesized and characterized to determine their thermal behaviour, stability, and conductivity. [C₁mpyr][NPf₂], [C₂mpyr][NPf₂], and [C₁mpyr][CTf₃] exhibit behaviour indicative of a plastic crystal phase. Both [C₃mpyr][NPf₂] and [C₄mpyr][NPf₂] are RTILs, while all of the [CTf₃]^– salts, have melting points above 60°C. [C₃mpyr][NPf₂] exhibited the widest electrochemical window of 5.5 V. The [NPf2]– salt exhibited similar reductive limits to the [NTf₂]^– anion, –3.2 V versus Fc⁺|Fc, while [CTf₃]^– had lower reductive stability. The [CTf₃]^– salts were more stable towards oxidation, +2.5 V versus Fc⁺|Fc, compared to the [NPf₂]^– and [NTf₂]^– salts.

Zwitterionic additives for electrochemical devices

Zwitterionic electrolytes such as N-methyl-N-(n-butanesulfonate) pyrrolidinium are added to electrolyte compositions such as polyelectrolytes, ionic liquid electrolytes and molecular solvent electrolytes (for example, lithium hexafluorophosphate) to improve conductivity of the ion species, such as lithium, in the electrolyte. This has application to lithium based energy storage devices such as batteries and supercapacitors.

Structural studies of ambient temperature plastic crystal ion conductors

A number of novel organic ionic compounds based on the pyrrolidinium cation are described which have been found to be ion conductors in their solid states around room temperature. The properties of the compounds are consistent with their exhibiting plastic crystal phases. In order to understand some of the molecular origins of the plastic crystal behaviour and the ion conductivity that it promotes, a number of related compounds based on the imidazolium and ammonium cations are also described which have structural elements in common with the pyrrolidinium cation, but which do not show the plastic behaviour. It is found therefore that the nature of the cation is quite critical to the development of this behaviour. The alkyl methyl pyrrolidinium cation is found to produce plastic crystal phases when the alkyl chains are short, thereby preserving the ability of the cation to rotate with minimal steric hindrance. The ammonium and imidazolium cations of comparable size and structure are less able to produce these plastic phases, in many cases because the low temperature phase proceeds to melt rather than forming a stable rotator phase.