Structure effects of self-assembled Prussian blue confined in highly organized mesoporous TiO(2) on the electrocatalytic properties towards H(2)O(2) detection

Here we report the derivatization of mesoporous TiO(2) thin films for the preparation of H(2)O(2) amperometric sensors. The coordination of the bifunctional ligand 1,10 phenantroline, 5,6 dione on the surface Ti(IV) ions provides open coordination sites for Fe(II) cations which are the starting point for the growth of a layer of Prussian blue polymer. The porous structure of the mesoporous TiO(2) allows the growth, ion by ion of the coordination polymer. Up to four layer of Prussian blue can be deposit without losing the porous structure of the film, which results in an enhanced response of these materials as H(2)O(2) sensors. These porous confined PB modified electrodes are robust sensors that exhibit good reproducibility, environmental stability and high sensitivity towards H(2)O(2) detection. (C) 2010 Elsevier B.V. All rights reserved.

Effects of poly(vinyl alcohol) additions on the structure of silica xerogels

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Design of hierarchical porous aluminas by using one-pot synthesis and different calcination temperatures

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dynamical scaling properties of nanoporous undoped and Sb-doped SnO2 supported thin films during tri- and bidimensional structure coarsening

The coarsening of the nanoporous structure developed in undoped and 3% Sb-doped SnO2 sol-gel dip-coated films deposited on a mica substrate was studied by time-resolved small-angle x-ray scattering (SAXS) during in situ isothermal treatments at 450 and 650 degrees C. The time dependence of the structure function derived from the experimental SAXS data is in reasonable agreement with the predictions of the statistical theory of dynamical scaling, thus suggesting that the coarsening process in the studied nanoporous structures exhibits dynamical self-similar properties. The kinetic exponents of the power time dependence of the characteristic scaling length of undoped SnO2 and 3% Sb-doped SnO2 films are similar (alpha approximate to 0.09), this value being invariant with respect to the firing temperature. In the case of undoped SnO2 films, another kinetic exponent, alpha('), corresponding to the maximum of the structure function was determined to be approximately equal to three times the value of the exponent alpha, as expected for the random tridimensional coarsening process in the dynamical scaling regime. Instead, for 3% Sb-doped SnO2 films fired at 650 degrees C, we have determined that alpha(')approximate to 2 alpha, thus suggesting a bidimensional coarsening of the porous structure. The analyses of the dynamical scaling functions and their asymptotic behavior at high q (q being the modulus of the scattering vector) provided additional evidence for the two-dimensional features of the pore structure of 3% Sb-doped SnO2 films. The presented experimental results support the hypotheses of the validity of the dynamic scaling concept to describe the coarsening process in anisotropic nanoporous systems.

Structure of SnO2 alcosols and films prepared by sol-gel dip coating

To obtain SnO2 films to be used for surface protection of fluoride glasses, a non-aqueous sol-gel route for the preparation was developed. An ethanolic SnO2 colloidal suspension was prepared by thermohydrolysis of SnCl4 solution at 70 degreesC. By using this procedure, redispersable powders with nanometer sized particles were obtained. Films were obtained by dip coating on glass and mica substrates. The structures of the ethanolic precursor suspension and films were compared to those of similar samples prepared by the classical aqueous sol-gel route. Comparative analyses performed by photon correlation spectroscopy demonstrated that the powders obtained by freeze-drying are fully redispersable either in aqueous or in alcoholic solutions at pH greater than or equal to 8. As prepared sols and redispersed colloidal suspensions have hydrodynamic radius distribution (2-14 nm) with an average size close to 7 nm. The variations in film structures with firing temperature were investigated by small-angle X-ray scattering and X-ray reflectometry. The experimental results show that the films have a two level porous structure composed of agglomerates of primary colloidal particles. The sintering of the primary particles leads to the densification of agglomerates and to the formation of inter-agglomerate spatially correlated pores. The volume fraction of intra-agglomerate pores is reduced from approximate to 50% to approximate to 30% by the precipitation of precursor salts partially hydrolyzed in ethanolic solution. (C) 2001 Elsevier B.V. B.V. All rights reserved.

Powder processing and In Vivo evaluation of a titanium porous coating implant

The processing of titanium porous coatings using powder metallurgy technique to achieve a porous structure that allows osseointegration with bone tissue was discussed. The porous microstructure exhibited micropores and interconnected macropores with size ranges that allowed bone ingrowth. The macropores in the coatings were originated from the binder evaporation while the micropore was related with the porous titanium powder and the low compaction pressure used. The in vivo evaluation indicated that osseointegration had occurred between the bone and porous material.

Development of glass-ceramics from combination of industrial wastes together with boron mining waste

The utilization of borate mineral wastes with glass-ceramic technology was first time studied and primarily not investigated combinations of wastes were incorporated into the research. These wastes consist of; soda lime silica glass, meat bone and meal ash and fly ash. In order to investigate possible and relevant application areas in ceramics, kaolin clay, an essential raw material for ceramic industry was also employed in some studied compositions. As a result, three different glass-ceramic articles obtained by using powder sintering method via individual sintering processes. Light weight micro porous glass-ceramic from borate mining waste, meat bone and meal ash and kaolin clay was developed. In some compositions in related study, soda lime silica glass waste was used as an additive providing lightweight structure with a density below 0.45 g/cm3 and a crushing strength of 1.8±0.1 MPa. In another study within the research, compositions respecting the B2O3–P2O5–SiO2 glass-ceramic ternary system were prepared from; borate wastes, meat bone and meal ash and soda lime silica glass waste and sintered up to 950ºC. Low porous, highly crystallized glass-ceramic structures with density ranging between 1.8 ± 0,7 to 2.0 ± 0,3 g/cm3 and tensile strength ranging between 8,0 ± 2 to 15,0 ± 0,5 MPa were achieved. Lastly, diopside - wollastonite (SiO2-Al2O3-CaO )glass-ceramics from borate wastes, fly ash and soda lime silica glass waste were successfully obtained with controlled rapid sintering between 950 and 1050ºC. The wollastonite and diopside crystal sizes were improved by adopting varied combinations of formulations and heating rates. The properties of the obtained materials show; the articles with a uniform pore structure could be useful for thermal and acoustic insulations and can be embedded in lightweight concrete where low porous glass-ceramics can be employed as building blocks or additive in cement and ceramic industries.

Cryptic invertebrates on subtidal rocky reefs vary with microhabitat structure and protection from fishing

The deployment of flat concrete blocks on subtidal rocky reefs can replicate natural reef microhabitats and provides a means for standardized sampling of cryptic invertebrates. The shape of the cavity beneath the block is related to reef topography and may influence the invertebrate community by affecting the amount of space for cryptic fauna to colonise and influencing the effectiveness of their predator-defence mechanisms. To determine the effect of sub-block reef structure and different levels of external predators on cryptic molluscs and echinoderms, I deployed concrete blocks at locations inside and outside the Maria Island marine reserve in eastern Tasmania, Australia. Relationships between sub-block reef structure and the cryptic invertebrate assemblage were evident between locations, whereas only a small but significant proportion of variation of assemblages between blocks within location was explained by reef surface area. No clear association with external predation pressure was evident in multivariate analyses of variation in assemblage structure. Juvenile abalone Haliotis rubra were not influenced by micro-habitat structure but were significantly less abundant at protected locations, the only species to exhibit such a response. This result follows a decline of emergent adult abalone in the marine reserve and raises the possibility of recruitment failure of abalone at some fully protected locations in the longer term.

Influence of cement properties in the reaction rate and mechanical behavior of concrete with high fl y ash content

The use of fly ash (FA) as an admixture to concrete is broadly extended for two main reasons: the reduction of costs that supposes the substitution of cement and the micro structural changes motivated by the mineral admixture. Regarding this second point, there is a consensus that considers that the ash generates a more compact concrete and a reduction in the size of the pore. However, the measure in which this contributes to the pozzolanic activity or as filler is not well defined. There is also no justification to the influence of the physical parameters, fineness of the grain and free water, in its behavior. This work studies the use of FA as a partial substitute of the cement in concretes of different workability (dry and wet) and the influence in the reactivity of the ash. The concrete of dry consistency which serves as reference uses a cement dose of 250 Kg/m 3 and the concrete of fluid consistency utilized a dose of cement of 350 Kg/m 3 . Two trademark of Portland Cement Type 1 were used. The first reached the resistant class for its fineness of grain and the second one for its composition. Moreover, three doses of FA have been used, and the water/binder ratio was constant in all the mixtures. We have studied the mechanical properties and the micro-structure of the concretes by means of compressive strength tests, mercury intrusion porosimetry (MIP) and thermal analysis (TA). The results of compressive strength tests allow us to observe that concrete mixtures with cements of the same classification and similar dosage of binder do not present the same mechanical behavior. These results show that the effective water/binder ratio has a major role in the development of the mechanical properties of concrete. The study of different dosages using TA, thermo-gravimetry and differential thermal analysis, revealed that the portlandite content is not restrictive in any of the dosages studied. Again, this proves that the rheology of the material influences the reaction rate and content of hydrated cement products. We conclude that the available free water is determinant in the efficiency of pozzolanic reaction. It is so that in accordance to the availability of free water, the ashes can react as an active admixture or simply change the porous distribution. The MIP shows concretes that do not exhibit significant changes in their mechanical behavior, but have suffered significant variation in their porous structure

Probing the pore wall structure of nanoporous carbons using adsorption

Hitherto, adsorption has been traditionally used to study only the porous structure in disordered materials, while the structure of the solid phase skeleton has been probed by crystallographic methods such as X-ray diffraction. Here we show that for carbons density functional theory, suitably adapted to consider heterogeneity of the pore walls, can be reliably used to probe features of the solid structure hitherto accessibly only approximately even by crystallographic methods. We investigate a range of carbons and determine pore wall thickness distributions using argon adsorption, with results corroborated by X-ray diffraction.

Anodic behavior of InP: film growth, porous structures and current oscillations.

We review our recent work on the anodization of InP in KOH electrolytes. The anodic oxidation processes are shown to be remarkably different in different concentrations of KOH. Anodization in 2 - 5 mol dm-3 KOH electrolytes results in the formation of porous InP layers but, under similar conditions in a 1 mol dm-3 KOH, no porous structure is evident. Rather, the InP electrode is covered with a thin, compact surface film at lower potentials and, at higher potentials, a highly porous surface film is formed which cracks on drying. Anodization of electrodes in 2 - 5 mol dm-3 KOH results in the formation of porous InP under both potential sweep and constant potential conditions. The porosity is estimated at ~65%. A thin layer (~ 30 nm) close to the surface appears to be unmodified. It is observed that this dense, near-surface layer is penetrated by a low density of pores which appear to connected it to the electrolyte. Well-defined oscillations are observed when InP is anodized in both the KOH and (NH4)2S. The charge per cycle remains constant at 0.32 C cm-2 in (NH4)2S but increases linearly with potential in KOH. Although the characteristics of the oscillations in the two systems differ, both show reproducible and well-behaved values of charge per cycle.

WATER TRANSPORT THROUGH POROUS MEDIA AND IN FLOW CHANNELS OF PROTON EXCHANGE MEMBRANE FUEL CELL

Proton exchange membrane (PEM) fuel cell has been known as a promising power source for different applications such as automotive, residential and stationary. During the operation of a PEM fuel cell, hydrogen is oxidized in anode and oxygen is reduced in the cathode to produce the intended power. Water and heat are inevitable byproducts of these reactions. The water produced in the cathode should be properly removed from inside the cell. Otherwise, it may block the path of reactants passing through the gas channels and/or gas diffusion layer (GDL). This deteriorates the performance of the cell and eventually can cease the operation of the cell. Water transport in PEM fuel cell has been the subject of this PhD study. Water transport on the surface of the GDL, through the gas flow channels, and through GDL has been studied in details. For water transport on the surface of the GDL, droplet detachment has been measured for different GDL conditions and for anode and cathode gas flow channels. Water transport through gas flow channels has been investigated by measuring the two-phase flow pressure drop along the gas flow channels. As accumulated liquid water within gas flow channels resists the gas flow, the pressure drop increases along the flow channels. The two-phase flow pressure drop can reveal useful information about the amount of liquid water accumulated within gas flow channels. Liquid water transport though GDL has also been investigated by measuring the liquid water breakthrough pressure for the region between the capillary fingering and the stable displacement on the drainage phase diagram. The breakthrough pressure has been measured for different variables such as GDL thickness, PTFE/Nafion content within the GDL, GDL compression, the inclusion of a micro-porous layer (MPL), and different water flow rates through the GDL. Prior to all these studies, GDL microstructural properties have been studied. GDL microstructural properties such as mean pore diameter, pore diameter distribution, and pore roundness distribution have been investigated by analyzing SEM images of GDL samples.

Preparação, caracterização e modificação de adsorventes para remoção de pesticidas de águas

O objectivo principal deste trabalho de mestrado consistiu em avaliar a potencial utilização de materiais adsorventes, nomeadamente, de carvões activados (AC) preparados por activação química com KOH, a partir de PET reciclado, e de materiais com estrutura mesoporosa ordenada, do tipo MCM-41 e SBA-15, na remoção de ácido 4 - cloro - 2 - metilfenoxiacético (MCPA) e de azul de metileno (MB), presentes nas águas. Nesta tese apresentam-se estudos de preparação e caracterização de materiais micro e mesoporosos e também estudos de avaliação da capacidade adsortiva em fase líquida. Prepararam-se três materiais microporosos, nomeadamente, PET-2-700, PET-2-700ox (AC oxidado) e PET-2-700red (AC reduzido), dois materiais constituídos exclusivamente por mesoporos, Si-MCM-41 e Ti-MCM-41-50 e dois materiais contendo maioritariamente mesoporos, mas que também possuem alguma microporosidade, tais corno, Si-SBA-15 e Ti-SBA-15-50. A caracterização textural dos adsorventes foi inferida por adsorção de azoto a 77K e por de difracção de raios X. Recorreu-se a três métodos de análise das isotérmicas, nomeadamente, Dubinin-Radushkevich, Brunauer-Ernrnett-Teller e alfa-s (as). A caracterização química dos AC foi realizada recorrendo-se a técnicas de análise elementar (AE) e espectroscopia de infravermelho com transformadas de Fourier (FTIR) e à determinação do ponto de carga zero. Os três carvões activados possuem valores de área superficial externa idênticos, o PET-2-700 possui o maior volume microporoso e o PET-2-700ox exibe o maior diâmetro de poros. Por outro lado, o PET-2-700ox possui um carácter fortemente ácido, o PET-2-700 exibe carácter ligeiramente ácido e o PET-2-700red apresenta propriedades ligeiramente alcalinas. Com base na AE, todas as amostras possuem percentagens de carbono elevadas, sendo que o PET-2-700red apresenta o valor mais elevado. Os resultados obtidos para a caracterização estrutural dos revelaram a obtenção de materiais mesoporosos de alta qualidade, definida pela elevada regularidade e uniformidade da estrutura porosa. A análise dos parâmetros de caracterização textura! permitiu inferir que os quatro materiais mesoporosos possuem valores de área superficial elevados, e que os materiais SBA-15 apresentam valores de volume poroso total e de tamanho de poros superiores aos manifestados pelos MCM-41. A incorporação de titânio não conduziu a uma perda significativa de qualidade dos materiais substituídos em relação às correspondentes amostras de sílica. Efectuaram-se estudos de adsorção em fase líquida de forma a avaliar a possível aplicação dos vários adsorventes na remoção de MCPA e de MB de efluentes líquidos. concluiu-se que o tempo de equilíbrio de 72 horas seria adequado e que a capacidade de adsorção dos vários AC era superior em meio ácido. Com base nas isotérmicas de adsorção do MCPA e do MB e na aplicação da representação de Langmuir e de Freundlich, foi possível concluir que o PET-2-700 possui a maior capacidade de adsorção do MCPA, 1.42 mmol/g, enquanto que o PET-2-700ox revelou a maior capacidade de adsorção do MB, 1.43 mmol/g. Na realidade, os materiais microporosos estudados apresentaram percentagens de remoção elevadas, tanto do MCPA como do MB. Relativamente aos materiais mesoporosos ordenados preparados neste trabalho, a percentagem de remoção de para os poluentes em estudo foi relativamente baixa, constatando-se que nesta fase dos estudos não constituem uma alternativa viável à utilização dos AC. No entanto, uma funcionalização criteriosa dos mesmos pode eventualmente proporcionar um aumento da capacidade adsortiva. ABSTRACT: The work presented in this master thesis, consisted of evaluating the potential use of different adsorbents materials, like activated carbon (AC) prepared by chemical activation with KOH, from recycled poly (ethylene terephthalate) (PET) and materials with ordered mesoporous structure such as MCM-41 and SBA-15, for removing acid 4-chlorine-2-metilfenoxiacétic and methylene blue from aqueous phase. We had prepared three microporous materials, PET-200-700, PET-2-700ox (AC oxidized) and PET-2-700red (reduced AC), two materials consisting exclusively of mesopores, Si-MCM-41 and Ti-MCM-41-50 and two materials containing mainly mesopores, but also having some microporosity, such as Si-SBA-15 and Ti-SBA-15-50. The textural characterization of the adsorbents was inferred by nitrogen adsorption at 77K and X-ray diffraction. Three methods were used to analyse the isotherms, namely, Dubinin-Radushkevich, Brunauer-Emmett-Teller and alpha-s (as). The chemical characterization of AC was performed using the elementary analysis, Fourier transform infrared spectroscopy (FTIR) and determination of the point of zero charge. Concerning the AC, the three present almost the same externa! surface area, PET-2-700 has a high micropore volume and PET-2-700ox shows the largest pore size diameter. On the other hand, PET-2-700ox had a strong acid character, PET-2-700 exhibits just a slightly acid character and PET-2-700red presents alkaline properties. The AE analysis allows confirming the high carbon content of theses AC, with PET-2-700red exhibiting the highest carbon proportion. The results from the structural characterization of the mesoporous materials, had disclosed the attainment of materials with high quality, defined by the raised regularity and uniformity of the porous structure. The analysis of the textural parameters allowed inferring that the four studied mesoporous materials possess high superficial area. The SBA-15 type materials present higher values of total porous volume and pores size diameter as the MCM-41. Also, the titanium incorporation did not lead to a significant loss of quality of the materials substituted in relation to the corresponding silica samples. The adsorption studies in liquid phase allow evaluating the possibility of using the different adsorbents for the MCPA and the MB removal. The kinetic studies had allowed to state the equilibrium time as 72 hours and a higher adsorption capacity was achieved in an acid medium. The influence of the pH of the medium, on the MCPA adsorption was evaluated. The MCPA and MB isotherms were analysed based on the Langmuir and Freundlich equation, the representations presented an excellent linearity, indicating the applicability of these equations to these systems. Also, it allows concluded that PET-2-700 had a higher adsorption capacity for MCPA, 1.42 mmol/g, and PET-2-700ox had a higher adsorption capacity for MB, 1.43 mmol/g. The AC used presented high removal percentages for MCPA and MB. Concerning the mesoporous materials prepared in this work, the percentage removal for the pollutants in study was relatively low, and evidencing that at the moment these mesoporous materials do not constitute a viable alternative to the AC. However, an astute funcionalisation of the same ones can, eventually provide an increase of the adsorption capacity.

Polyurethane (PU) scaffolds prepared by solvent casting/particulate leaching (SCPL) combined with centrifugation

This article reports an enhanced solvent casting/particulate (salt) leaching (SCPL) method developed for preparing three-dimensional porous polyurethane (PU) scaffolds for cardiac tissue engineering. The solvent for the preparation of the PU scaffolds was a mixture of dimethylformamide (DFM) and tetrahydrofuran (THF). The enhanced method involved the combination of a conventional SCPL method and a step of centrifugation, with the centrifugation being employed to improve the pore uniformity and the pore interconnectivity of scaffolds. Highly porous three-dimensional scaffolds with a well interconnected porous structure could be achieved at the polymer solution concentration of up to 20% by air or vacuum drying to remove the solvent. When the salt particle sizes of 212-295, 295-425, or 425-531 µm and a 15% w/v polymer solution concentration were used, the porosity of the scaffolds was between 83-92% and the compression moduli of the scaffolds were between 13 kPa and 28 kPa. Type I collagen acidic solution was introduced into the pores of a PU scaffold to coat the collagen onto the pore walls throughout the whole PU scaffold. The human aortic endothelial cells (HAECs) cultured in the collagen-coated PU scaffold for 2 weeks were observed by scanning electron microscopy (SEM). It was shown that the enhanced SCPL method and the collagen coating resulted in a spatially uniform distribution of cells throughout the collagen-coated PU scaffold.

Microstructural characterization of electron beam evaporated tungsten oxide films for gas sensing applications

Tungsten trioxide is one of the potential semiconducting materials used for sensing NH3, CO, CH4 and acetaldehyde gases. The current research aims at development, microstructural characterization and gas sensing properties of thin films of Tungsten trioxide (WO3). In this paper, we intend to present the microstructural characterization of these films as a function of post annealing heat treatment. Microstructural and elemental analysis of electron beam evaporated WO3 thin films and iron doped WO3 films (WO3:Fe) have been carried out using analytical techniques such as Transmission electron microscopy, Rutherford Backscattered Spectroscopy and XPS analysis. TEM analysis revealed that annealing at 300oC for 1 hour improves cyrstallinity of WO3 film. Both WO3 and WO3:Fe films had uniform thickness and the values corresponded to those measured during deposition. RBS results show a fairly high concentration of oxygen at the film surface as well as in the bulk for both films, which might be due to adsorption of oxygen from atmosphere or lattice oxygen vacancy inherent in WO3 structure. XPS results indicate that tungsten exists in 4d electronic state on the surface but at a depth of 10 nm, both 4d and 4f electronic states were observed. Atomic force microscopy reveals nanosize particles and porous structure of the film. This study shows e-beam evaporation technique produces nanoaparticles and porous WO3 films suitable for gas sensing applications and doping with iron decreases the porosity and particle size which can help improve the gas selectivity.