Design of Piles for Integral Abutment Bridges, HR-252, 1984

More and more, integral abutment bridges are being used in place of the more traditional bridge designs with expansion releases. In this study, states which use integral abutment bridges were surveyed to determine their current practice in the design of these structures. To study piles in integral abutment bridges, a finite element program for the soil-pile system was developed (1) with materially and geometrically nonlinear, two and three dimensional beam elements and (2) with a nonlinear, Winkler soil model with vertical, horizontal, and pile tip springs. The model was verified by comparison to several analytical and experimental examples. A simplified design model for analyzing piles in integral abutment bridges is also presented. This model grew from previous analytical models and observations of pile behavior. The design model correctly describes the essential behavioral characteristics of the pile and conservatively predicts the vertical load-carrying capacity. Analytical examples are presented to illustrate the effects of lateral displacements on the ultimate load capacity of a pile. These examples include friction and end-bearing piles; steel, concrete, and timber piles; and bending about the weak, strong, and 45° axes for H piles. The effects of cyclic loading are shown for skewed and nonskewed bridges. The results show that the capacity of friction piles is not significantly affected by lateral displacements, but the capacity of end-bearing piles is reduced. Further results show that the longitudinal expansion of the bridge can introduce a vertical preload on the pile.

Case Study of Seasonal Variation in the Subgrade and Subbase Layers of Highway US 20, TR-516, 2008

Seasonal variations in ground temperature and moisture content influence the load carrying capacity of pavement subgrade layers. To improve pavement performance, pavement design guidelines require knowledge of environmental factors and subgrade stiffness relationships. As part of this study, in-ground instrumentation was installed in the pavement foundation layers of a newly constructed section along US Highway 20 near Fort Dodge, Iowa, to monitor the seasonal variations in temperature, frost depth, groundwater levels, and moisture regime. Dynamic cone penetrometer (DCP), nuclear gauge, and Clegg hammer tests were performed at 64 test points in a 6-ft x 6-ft grid pattern to characterize the subgrade stiffness properties (i.e., resilient modulus) prior to paving. The purpose of this paper is to present the field instrumentation results and the observed changes in soil properties due to seasonal environmental effects.

Investigation of Steel-Stringer Bridges: Superstructures and Substructures, Volume I, TR-522, 2007

There are hundreds of structurally deficient or functionally obsolete bridges in the state of Iowa. With the majority of these bridges located on rural county roads where there is limited funding available to replace the bridges, diagnostic load testing can be utilized to determine the actual load carrying capacity of the bridge. One particular family or fleet of bridges that has been determined to be desirable for load testing consists of single-span bridges with non-composite, cast-in-place concrete decks, steel stringers, and timber substructures. Six bridges with poor performing superstructure and substructure from the aforementioned family of bridges were selected to be load tested. The six bridges were located on rural roads in five different counties in Iowa: Boone, Carroll, Humboldt, Mahaska, and Marshall. Volume I of this report focuses on evaluating the superstructure for this family of bridges. This volume discusses the behavior characteristics that influence the load carrying capacity of this fleet of bridges. In particular, the live load distribution, partial composite action, and bearing restraint were investigated as potential factors that could influence the bridge ratings. Implementing fleet management practices, the bridges were analyzed to determine if the load test results could be predicted to better analyze previously untested bridges. For this family of bridges it was found that the ratings increased as a result of the load testing demonstrating a greater capacity than determined analytically. Volume II of this report focuses on evaluating the timber substructure for this family of bridges. In this volume, procedures for detecting pile internal decay using nondestructive ultrasonic stress wave techniques, correlating nondestructive ultrasonic stress wave techniques to axial compression tests to estimate deteriorated pile residual strength, and evaluating load distribution through poor performing timber substructure elements by instrumenting and load testing the abutments of the six selected bridges are discussed. Also, in this volume pile repair methods for restoring axial and bending capacities of pile are developed and evaluated.

Fibre-reinforced composites as root canal posts

Fibre-reinforced composite (FRC) root canal posts are suggested to have biomechanical benefits over traditional metallic posts, but they lack good adhesion to resin composites. The aim of this series of studies was to evaluate the adhesion of individually formed fibre-reinforced composite material to composite resin and dentin, as well as some mechanical properties. Flexural properties were evaluated and compared between individually formed FRC post material and different prefabricated posts. The depth of polymerization of the individually formed FRC post material was evaluated with IR spectrophotometry and microhardness measurements, and compared to that of resin without fibres. Bonding properties of the individually formed FRC post to resin cements and dentin were tested using Pull-out- and Push-out-force tests, evaluated with scanning electron microscopy, and compared to those of prefabricated FRC and metal posts. Load-bearing capacity and microstrain were evaluated and failure mode assessment was made on incisors restored with individually formed FRC posts of different structures and prefabricated posts. The results of these studies show that the individually polymerized and formed FRC post material had higher flexural properties compared to the commercial prefabricated FRC posts. The individually polymerized FRC material showed almost the same degree of conversion after light polymerization as monomer resin without fibres. Moreover, it was found that the individually formed FRC post material with a semiinterpenetrating polymer network (IPN) polymer matrix bonded better to composite resin luting cement, than did the prefabricated posts with a cross-linked polymer matrix. Furthermore, it was found that, contrary to the other posts, there were no adhesive failures between the individually formed FRC posts and composite resin luting cement. This suggests better interfacial adhesion of cements to these posts. Although no differences in load-bearing capacity or microstrain could be seen, the incisors restored with individually formed FRC posts with a hollow structure showed more favourable failures compared to other prefabricated posts. These studies suggest that it is possible to use individually formed FRC material with semi-IPN polymer matrix as root canal post material. They also indicate that there are benefits especially regarding the bonding properties to composite resin and dentin with this material compared to prefabricated FRC post material with a cross-linked matrix. Furthermore, clinically more repairable failures were found with this material compared to those of prefabricated posts.

Viilukuivurin suunnittelu kuivaustehon ja -laadun parantamiseksi

Työn tarkoitus tutkia viilukuivurin ilmankiertoa. Tietojen pohjalta suunnitellaan alustava 6-kerroskuivuri. Lisäksi diplomityössä tutkitaan erilaisten kuivausparametrien vaikutusta kuivaustapahtumaan. Viilunkuivauksessa on tärkeää tasainen kuivaustulos. Kuivaustapahtumaan vaikuttavat monet parametrit, joista yksi tärkeimmistä on kuivausilman nopeus suuttimissa. Kun viilukuivurin kuivausilman kierto on tasapainossa, saadaan kuivurin jokaisen kerroksen suutinnopeus yhtäläiseksi. Työ tarkastelee kuivurin kennon eri osien: puhaltimen, patterin, kanavien ja suutinlaatikoiden vaikutusta kuivausilman virtaamiin. Tietojen perusteella on tarkoitus optimoida kuivausolosuhteet kennon eri osissa. Teorian lisäksi työssä on tarkasteltu erilaisten virtausmallien avulla kuivausilman kiertoa kennossa. Eri kuivausparametrien vaikutusta on tutkittu viilun kuivumista simuloivalla ohjelmalla. Kuivurin konstruktion kuormituskestävyyttä on arvioitu FEM-malleilla. Lopputuloksena on saatu alustava malli VTS6x6200 kuivurille.

Teräspalkkirakenteiden palomitoitus hiilivetypalossa

Työn tavoitteena oli kehittää teräspalkkirakenteiden palosuunnittelua ja palosuojauksen toteutusta öljynjalostamolla käytettävien kantavien teräspalkkirakenteiden osalta. Lisäksi tavoitteena oli luoda suunnitteluohjeen runko palomitoituksen toteuttamiseksi Neste Engineering Oy:ssä. Ongelmakohtia työssä olivat rakenteiden kapasiteettien tarkka määritys, toimivien toteutusratkaisujen etsiminen, sekä öljynjalostamolla mitoituspalona käytettävän hiilivetypalon SFS-ENV-1992-1-2 käyttö yleisemmin mitoituspalona käytettävän standardipalo ISO-834 sijaan. Työssä perehdyttiin kirjallisuuden perusteella eri palosuojausmenetelmiin. Tarkemman jatkotutkimuksen kohteeksi otettiin jo käytössä hyväksi havaittu teräsputkipalkkien sisäpuoleinen betonitäyttö. Menetelmässä teräsputkipalkin oletetaan kantavan kuormat normaalitilassa ja sisällä olevan raudoitetun betonin palossa. Palkkirakenteiden kapasiteettimitoitus määritettiin laskennallisesti poikkileikkauksille. Mitoitus perustuu palkissa tapahtuvien sisäisten venymien ja puristumien tarkasteluun, sekä poikkileikkauksen tarkan lämpötilajakauman huomioimiseen. Raudoitustankojen ankkurointia palkki-pilari-liitoksessa kehitettiin valmistuksen kannalta yksioikoisemmaksi ja helpommin toteutettavaksi. Palkkien raudoituksiin suunniteltiin kierremuhvijatkoksella toteutettava ankkurointimenetelmä, jolla palkkien raudoitustangot saadaan ankkuroitua täydestä kapasiteetistaan tapauskohtaisesti pilarin vastakkaisella puolella olevaan palkkiin tai ankkurointikappaleella pilariin. Teräsputkipilarin betonivalun vaihtoehtoisiin menetelmiin tutustuttiin. Pilarin alapäähän asennettavan venttiilin läpi tapahtuva täyttö helpottaa betonointityövaihetta. Tutkimuksen tuloksena luotiin suunnitteluohjeen runko, jonka pohjalta voidaan tehdä lopullinen ohje. Myös työn tuloksena saatu laskentaohjelma palkkien momentti-kapasiteetin ja pilarin nurjahduskuorman laskemiseksi helpottaa suunnittelua. Raudoituksen ankkurointiin ja betonointiin esitettyjen menetelmien toimivuus on syytä kokeilla käytännössä ja tehdä jatkokehitys näistä saatavien kokemusten pohjalta.

The Influence of Certain Processing Factors on the Durability of Yttrium Stabilized Zirconia Used As Dental Biomaterial

In dentistry, yttrium partially stabilized zirconia (ZrO2) has become one of the most attractive ceramic materials for prosthetic applications. The aim of this series of studies was to evaluate whether certain treatments used in the manufacturing process, such as sintering time, color shading or heat treatment of zirconia affect the material properties. Another aim was to evaluate the load-bearing capacity and marginal fit of manually copy-milled custom-made versus prefabricated commercially available zirconia implant abutments. Mechanical properties such as flexural strength and surface microhardness were determined for green-stage milled and sintered yttrium partially stabilized zirconia after different sintering time, coloring process and heat treatments. Scanning electron microscope (SEM) was used for analyzing the possible changes in surface structure of zirconia material after reduced sintering time, coloring and heat treatments. Possible phase change from the tetragonal to the monoclinic phase was evaluated by X-ray diffraction analysis (XRD). The load-bearing capacity of different implant abutments was measured and the fit between abutment and implant replica was examined with SEM. The results of these studies showed that the shorter sintering time or the thermocycling did not affect the strength or surface microhardness of zirconia. Coloring of zirconia decreased strength compared to un-colored control zirconia, and some of the colored zirconia specimens also showed a decrease in surface microhardness. Coloring also affected the dimensions of zirconia. Significantly decreased shrinkage was found for colored zirconia specimens during sintering. Heat treatment of zirconia did not seem to affect materials’ mechanical properties but when a thin coating of wash and glaze porcelain was fired on the tensile side of the disc the flexural strength decreased significantly. Furthermore, it was found that thermocycling increased the monoclinic phase on the surface of the zirconia. Color shading or heat treatment did not seem to affect phase transformation but small monoclinic peaks were detected on the surface of the heat treated specimens with a thin coating of wash and glaze porcelain on the opposite side. Custom-made zirconia abutments showed comparable load-bearing capacity to the prefabricated commercially available zirconia abutments. However, the fit of the custom-made abutments was less satisfactory than that of the commercially available abutments. These studies suggest that zirconia is a durable material and other treatments than color shading used in the manufacturing process of zirconia bulk material does not affect the material’s strength. The decrease in strength and dimensional changes after color shading needs to be taken into account when fabricating zirconia substructures for fixed dental prostheses. Manually copy-milled custom-made abutments have acceptable load-bearing capacity but the marginal accuracy has to be evaluated carefully.

Lujasta rakenneteräksestä tehdyn rakenteen vikasietoisuuden määritys

Tässä työssä tutkittiin Ruukin valmistamista lujista Optim 700 MC Plus sekä Optim 700 QL teräksistä tehtyjen hitsattujen palkkirakenteiden vikasietoisuutta sekä murtumiskäyttäytymistä laboratoriossa suoritettujen täyden mittakaavan kokeiden avulla. Koerakenteet suunniteltiin siten, että rakenteen kylmämuovauksen sekä hitsauksen vaikutukset yhdessä rakenteen geometrian vaikutuksen kanssa heikentävät rakenteen murtumissitkeyttä rakenteeseen tehdyn teräväkärkisen alkusärön tasossa. Suunnitellussa koesarjassa varioidaan testauslämpötilan lisäksi hitsauksen lämmöntuontia sekä koerakenteeseen tehtävän alkusärön kokoa. Tässä työssä tavoitteena oli yleisesti esittää menettely hitsatun säröllisen teräsrakenteen kestävyyden arviointia varten. Optim 700 MC Plus teräksestä tehdyn koerakenteen käyttäytymistä tutkittiin laskennallisesti murtumismekaniikan avulla. Laadittujen FEM - mallien avulla laskettiin rakenteen murtumisparametrien arvot kummallekin tutkittavalle teräkselle. Optim 700 MC Plus materiaalista valmistetuille koerakenteen säröalueen rakennedetaljia vastaavalle koekappaleille suoritettiin murtumissitkeyskokeita. Murtumissitkeyskokeista saatujen tulosten avulla pystyttiin kuvaamaan täyden mittakaavan koerakenteessa olevan särön murtumiskäyttäytymistä mitoitusmenetelmissä. Koerakenteelle laskettiin tässä työssä kriittisen särökoon ja sitä vastaavan kuorman arvot perustuen rakenteen oletettuun hauraaseen, epästabiiliin sitkeään sekä plastiseen murtumiskäyttäytymiseen. Tässä työssä testattiin molemmista tutkittavista materiaaleista valmistetut täyden mittakaavan koerakenteet -40 °C lämpötilassa. Molemmat testatut rakenteet käyttäytyvät mitattujen siirtymätulosten perusteella melko hauraasti. Optim 700 MC Plus materiaalille saatujen laskentatulosten voidaan todeta testatun koekappaleen perusteella soveltuvan hauraasti käyttäytyvän rakenteen mitoitukseen.

Unidirectional fiber-reinforced composite as an oral implant abutment material: Experimental studies of E-glass fiber/BisGMA-TEGDMA polymer in vitro

Fiber-reinforced composites (FRCs) are a new group of non-metallic biomaterials showing a growing popularity in many dental and medical applications. As an oral implant material, FRC is biocompatible in bone tissue environment. Soft tissue integration to FRC polymer material is unclear. This series of in vitro studies aimed at evaluating unidirectional E-glass FRC polymer in terms of mechanical, chemical, and biological properties in an attempt to develop a new non-metallic oral implant abutment alternative. Two different types of substrates were investigated: (a) Plain polymer (BisGMA 50%–TEGDMA 50%) and (b) Unidirectional FRC. The mechanical behavior of high fiber-density FRCs was assessed using a three-point bending test. Surface characterization was performed using scanning electron and spinning disk confocal microscopes. The surface wettability/energy was determined using sessile drop method. The blood response, including blood-clotting ability and platelet morphology was evaluated. Human gingival fibroblast cell responses - adhesion kinetics, adhesion strength, and proliferation activity - were studied in cell culture environment using routine test conditions. A novel tissue culture method was developed and used to evaluate porcine gingival tissue graft attachment and growth on the experimental composite implants. The analysis of the mechanical properties showed that there is a direct proportionality in the relationship between E-glass fiber volume fraction and toughness, modulus of elasticity, and load bearing capacity; however, flexural strength did not show significant improvement when high fiber-density FRC is used. FRCs showed moderate hydrophilic properties owing to the presence of exposed glass fibers on the polymer surface. Blood-clotting time was shorter on FRC substrates than on plain polymer. The FRC substrates also showed higher platelet activation state than plain polymer substrates. Fibroblast cell adhesion strength and proliferation rate were highly pronounced on FRCs. A tissue culture study revealed that gingival epithelium and connective tissue established an immediate close contact with both plain polymer and FRC implants. However, FRC seemed to guide epithelial migration outwards from the tissue/implant interface. Due to the anisotropic and hydrophilic nature of FRC, it can be concluded that this material enhances biological events related with soft tissue integration on oral implant surface.

Lujasta teräksestä valmistetun palkin poikkileikkauksen optimointi

Parin viime vuosikymmenen aikana on kehitetty huomattavasti entistä lujempia teräslaatuja, joiden käyttö ei kuitenkaan ole yleistynyt läheskään samaan tahtiin. Korkeamman hinnan lisäksi yksi merkittävä syy tähän on, että suunnittelijoilla ei usein ole riittäviä tietoja siitä, millaisissa tilanteissa lujemman teräslaadun käytöstä on merkittävää hyötyä. Tilannetta ei myöskään helpota se, että käytössä olevat standardit eivät tarjoa lainkaan ohjeistusta kaikkein lujimpien, myötörajaltaan yli 700MPa terästen käyttöön ja mitoitukseen. Tässä työssä pyritään tarjoamaan suunnittelijalle ohjeita ja nyrkkisääntöjä sopivan lujuusluokan ja profiilin valintaan sekä yleisesti lujempien teräslaatujen käyttöön. Lujemman teräslaadun käytöllä voidaan keventää suunniteltavaa rakennetta ja saada aikaan huomattavia painonsäästöjä. Usein ongelmaksi nousevat kuitenkin stabiiliuskriteerit, sillä teräksen lommahduskestävyys määräytyy suuresti sen lujuusluokasta siten, että mitä lujempaa teräs on, sitä helpommin se lommahtaa. Kun tämä yhdistetään siihen, että lujempaa terästä käytettäessä rakenteesta tulee optimoituna muutenkin pienempi ja kevyempi, kasvaa näiden kahden asian yhteisvaikutuksena kantokyvyn mukaan mitoitetun rakenteen taipuma korkeampiin lujuusluokkiin edetessä hyvin nopeasti sallittujen rajojen yli. Työssä etsitään siksi keinoja sopivan kompromissin löytämiseksi lujuuden ja jäykkyyden välille. Koska muotoilulla ja poikkileikkauksella on suuri merkitys sekä taipuman että stabiliteetin kannalta, tutkitaan erilaisia poikkileikkausvaihtoehtoja ja etsitään optimaalista poikkileikkausta taivutuspalkille matemaattisen optimointimallin avulla. Kun eri poikkileikkausvaihtoehdot on käsitelty ja optimoitu taivutuksen suhteen, tutkitaan poikkileikkauksia myös muissa kuormitustapauksissa. Huomattavan raskaan laskentatyön takia apuna käytetään Matlab-ohjelmistoa itse optimointiin ja Femap-ohjelmaa muiden kuormitustapausten tutkimiseen ja tulosten verifioitiin.

Reconstruction of cranial bone defects with fiber-reinforced composite–bioactive glass implants

A cranial bone defect may result after an operative treatment of trauma, infection, vascular insult, or tumor. New biomaterials for cranial bone defect reconstructions are needed for example to mimic the biomechanical properties and structure of cranial bone. A novel glass fiber-reinforced composite implant with bioactive glass particulates (FRC–BG, fiber-reinforced composite–bioactive glass) has osteointegrative potential in a preclinical setting. The aim of the first and second study was to investigate the functionality of a FRC–BG implant in the reconstruction of cranial bone defects. During the years 2007–2014, a prospective clinical trial was conducted in two tertiary level academic institutions (Turku University Hospital and Oulu University Hospital) to evaluate the treatment outcome in 35 patients that underwent a FRC–BG cranioplasty. The treatment outcome was good both in adult and pediatric patients. A number of conventional complications related to cranioplasty were observed. In the third study, a retrospective outcome evaluation of 100 cranioplasty procedures performed in Turku University Hospital between years 2002–2012 was conducted. The experimental fourth study was conducted to test the load-bearing capacity and fracture behavior of FRC–BG implants under static loading. The interconnective bars in the implant structure markedly increased the load-bearing capacity of the implant. A loading test did not demonstrate any protrusions of glass fibers or fiber cut. The fracture type was buckling and delamination. In this study, a postoperative complication requiring a reoperation or removal of the cranioplasty material was observed in one out of five cranioplasty patients. The treatment outcomes of cranioplasty performed with different synthetic materials did not show significant difference when compared with autograft. The FRC–BG implant was demonstrated to be safe and biocompatible biomaterial for large cranial bone defect reconstructions in adult and pediatric patients.

Recyclable Short Fibre Reinforced Plastics PP/Nylon and HDPE/Nylon composites

The study shows that standard plastics like polypropylene and high density polyethylene can be reinforced by adding nylon short fibres. Compared to the conventional glass reinforced thermoplastics this novel class of reinforced thermoplastics has the major advantage of recyclability. Hence such composites represent a new spectrum of recyclable polymer composites. The fibre length and fibre diameter used for reinforcement are critical parameters While there is a critical fibre length below which no effective reinforcement takes place, the reinforcement improves when the fibre diameter decreases due to increased surface area.While the fibres alone give moderate reinforcement, chemical modification of the matrix can further improve the strength and modulus of the composites. Maleic anhydride grafting in presence of styrene was found to be the most efficient chemical modification. While the fibre addition enhances the viscosity of the melt at lower shear rates, the enhancement at higher shear rate is only marginal. This shows that processing of the composite can be done in a similar way to that of the matrix polymer in high shear operations such as injection moulding. Another significant observation is the decrease in melt viscosity of the composite upon grafting. Thus chemical modification of matrix makes processing of the composite easier in addition to improving the mechanical load bearing capacity.For the development of a useful short fibre composite, selection of proper materials, optimum design with regard to the particular product and choosing proper processing parameters are most essential. Since there is a co-influence of many parameters, analytical solutions are difficult. Hence for selecting proper processing parameters 'rnold flow' software was utilized. The orientation of the fibres, mechanical properties, temperature profile, shrinkage, fill time etc. were determined using the software.Another interesting feature of the nylon fibre/PP and nylon fibre/HDPE composites is their thermal behaviour. Both nylon and PP degrade at the same temperature in single steps and hence the thermal degradation behaviour of the composites is also being predictable. It is observed that the thermal behaviour of the matrix or reinforcement does not affect each other. Almost similar behaviour is observed in the case of nylon fibre/HDPE composites. Another equally significant factor is the nucleating effect of nylon fibre when the composite melt cools down. In the presence of the fibre the onset of crystallization occurs at slightly higher temperature.When the matrix is modified by grafting, the onset of crystallization occurs at still higher temperature. Hence it may be calculated that one reason for the improvement in mechanical behaviour of the composite is the difference in crystallization behaviour of the matrix in presence of the fibre.As mentioned earlier, a major advantage of these composites is their recyclability. Two basic approaches may be employed for recycling namely, low temperature recycling and high temperature recycling. In the low temperature recycling, the recycling is done at a temperature above the melting point of the matrix, but below that of the fibres while in the high temperature route. the recycling is done at a temperature above the melting points of both matrix and fibre. The former is particularly interesting in that the recycled material has equal or even better mechanical properties compared to the initial product. This is possible because the orientation of the fibre can improve with successive recycling. Hence such recycled composites can be used for the same applications for which the original composite was developed. In high temperature recycling, the composite is converted into a blend and hence the properties will be inferior to that of the original composite, but will be higher than that of the matrix material alone.

Studies on the fracture behaviour of polymer blends with special reference to PP/HDPE and PS/HIPS blends

Investigations on the fracture behaviour of polymer blends is the topic of this thesis. The blends selected are PP/HDPE and PS/HIPS. PP/HDPE blend is chosen due to its commercial importance and PS/HIPS blend is selected to study the transition from brittle fracture to ductile fracture.PP/HDPE blends were prepared at different compositions by melt blending at 180°C and fracture failure process was investigated by conducting notch sensitivity test and tensile test at different strain rates. The effects of two types of modifiers (particulate and elastomer) on the fracture behaviour and notch sensitivity of PP/HDPE blends were studied. The modifiers used are calcium carbonate, a hard particulate filler commonly used in plastics and Ethylene Propylene Diene Monomer (EPDM). They were added in 2%, 4% and 6% by weight of the blends.The study shows that the mechanical properties of PP/HDPE blends can be optimized by selecting proper blend compositions. The selected modifiers are found to alter and improve the fracture behaviour and notch sensitivity of the blends. Particulate fillers like calcium carbonate can be used for making the mechanical behaviour more stable at the various blend compositions. The resistance to notch sensitivity of the blends is found to be marginally lower in the presence of calcium carbonate. The elastomeric modifier EPDM produces a better stability of the mechanical behaviour. A low concentration of EPDM is sufficient to effect such a change. EPDM significantly improves the resistance to notch sensitivity of the blends. The study shows that judicious selection of modifiers can improve the fracture behaviour and notch sensitivity of PP/HDPE blends and help these materials to be used for critical applications.For investigating the transition in fracture behaviour and failure modes, PS/HIPS blends were selected. The blends were prepared by melt mixing followed by injection moulding to prepare the specimens for conducting tensile, impact and flexure tests. These tests were used to simulate the various conditions which promote failure.The tensile behaviour of unnotched and notched PS/HIPS blend samples were evaluated at slow speeds. Tensile strengths and moduli were found to increase at the higher testing speed for all the blend combinations whereas maximum strain at break was found to decrease. For a particular speed of testing, the tensile strength and modulus show only a very slight decrease as HIPS content is increased up to about 40%. However, there is a drastic decrease on increasing the HIPS content thereafter.The maximum strain at break shows only a very slight change up to about 40% HIPS content and thereafter shows a remarkable increase. The notched specimens also follow a comparable trend even though the notch sensitivity is seen high for PS rich blends containing up to 40% HIPS. The notch sensitivity marginally decreases with increase in HIPS content. At the same time, it is found to increase with the increase in strain rate. It is observed that blends containing more than 40% HIPS fail in ductile mode.The impact characteristics of PSIHIPS blends studied were impact strength, the energy absorbed by the test specimen and impact toughness. Remarkable increase in impact strength is observed as HIPS content in the blend exceeds 40%. The energy absorbed by the test specimens and the impact toughness also show a comparable trend.Flexural testing which helps to characterize the load bearing capacity was conducted on PS/HIPS blend samples at the two different testing speeds of 5mmlmin and 10 mm/min. The flexural strength increases with increase in testing speed for all the blend compositions. At both the speeds, remarkable reduction in flexural strength is observed as HIPS content in the blend exceeds 40%. The flexural strain and flexural energy absorbed by the specimens are found to increase with increase in HIPS content. At both the testing speeds, brittle fracture is observed for PS rich blends whereas HIPS rich blends show ductile mode of failure.Photoelastic investigations were conducted on PS/HIPS blend samples to analyze their failure modes. A plane polariscope with a broad source of light was utilized for the study. The coloured isochromatic fringes formed indicate the presence of residual stress concentration in the blend samples. The coverage made by the fringes on the test specimens varies with the blend composition and it shows a reducing trend with the increase in HIPS content. This indicates that the presence of residual stress is a contributing factor leading to brittle fracture in PS rich blends and this tendency gradually falls with increase in HIPS content and leads to their ductile mode of failure.

Verbesserung der seismischen Kapazität von Mauerwerkswänden durch Verwendung von Elastomerlagern

Ein großer Teil der Schäden wie auch der Verluste an Gesundheit und Leben im Erdbebenfall hat mit dem frühzeitigen Versagen von Mauerwerksbauten zu tun. Unbewehrtes Mauerwerk, wie es in vielen Ländern üblich ist, weist naturgemäß einen begrenzten Erdbebenwiderstand auf, da Zugspannungen und Zugkräfte nicht wie bei Stahlbeton- oder Stahlbauten aufgenommen werden können. Aus diesem Grund wurde bereits mit verschiedenen Methoden versucht, die Tragfähigkeit von Mauerwerk im Erdbebenfall zu verbessern. Modernes Mauerwerk kann auch als bewehrtes oder eingefasstes Mauerwerk hergestellt werden. Bei bewehrtem Mauerwerk kann durch die Bewehrung der Widerstand bei Beanspruchung als Scheibe wie als Platte verbessert werden, während durch Einfassung mit Stahlbetonelementen in erster Linie die Scheibentragfähigkeit sowie die Verbindung zu angrenzenden Bauteilen verbessert wird. Eine andere interessante Möglichkeit ist das Aufbringen textiler Mauerwerksverstärkungen oder von hochfesten Lamellen. In dieser Arbeit wird ein ganz anderer Weg beschritten, indem weiche Fugen Spannungsspitzen reduzieren sowie eine höhere Verformbarkeit gewährleiten. Dies ist im Erdbebenfall sehr hilfreich, da die Widerstandfähigkeit eines Bauwerks oder Bauteils letztlich von der Energieaufnahmefähigkeit, also dem Produkt aus Tragfähigkeit und Verformbarkeit bestimmt wird. Wenn also gleichzeitig durch die weichen Fugen keine Schwächung oder sogar eine Tragfähigkeitserhöhung stattfindet, kann der Erdbebenwiderstand gesteigert werden. Im Kern der Dissertation steht die Entwicklung der Baukonstruktion einer Mauerwerkstruktur mit einer neuartigen Ausbildung der Mauerwerksfugen, nämlich Elastomerlager und Epoxydharzkleber anstatt üblichem Dünnbettmörtel. Das Elastomerlager wird zwischen die Steinschichten einer Mauerwerkswand eingefügt und damit verklebt. Die Auswirkung dieses Ansatzes auf das Verhalten der Mauerwerkstruktur wird unter dynamischer und quasi-statischer Last numerisch und experimentell untersucht und dargestellt.

Zum Querkrafttragverhalten von UHPC-Balken mit kombinierter Bewehrung aus Stahlfasern und Stabstahl

Ultrahochfester Beton besitzt aufgrund seiner Zusammensetzung eine sehr hohe Druckfestigkeit von 150 bis über 200 N/mm² und eine außergewöhnlich hohe Dichtigkeit. Damit werden Anwendungen in stark belasteten Bereichen und mit hohen Anforderungen an die Dauerhaftigkeit des Materials ermöglicht. Gleichzeitig zeigt ultrahochfester Beton bei Erreichen seiner Festigkeit ein sehr sprödes Verhalten. Zur Verhinderung eines explosionsartigen Versagens werden einer UHPC-Mischung Fasern zugegeben oder wird eine Umschnürung mit Stahlrohren ausgebildet. Die Zugabe von Fasern zur Betonmatrix beeinflusst neben der Verformungsfähigkeit auch die Tragfähigkeit des UHPC. Das Versagen der Fasern ist abhängig von Fasergeometrie, Fasergehalt, Verbundverhalten sowie Zugfestigkeit der Faser und gekennzeichnet durch Faserauszug oder Faserreißen. Zur Sicherstellung der Tragfähigkeit kann daher auf konventionelle Bewehrung außer bei sehr dünnen Bauteilen nicht verzichtet werden. Im Rahmen des Schwerpunktprogramms SPP 1182 der Deutschen Forschungsgemeinschaft (DFG) wurden in dem dieser Arbeit zugrunde liegenden Forschungsprojekt die Fragen nach der Beschreibung des Querkrafttragverhaltens von UHPC-Bauteilen mit kombinierter Querkraftbewehrung und der Übertragbarkeit bestehender Querkraftmodelle auf UHPC untersucht. Neben einer umfassenden Darstellung vorhandener Querkraftmodelle für Stahlbetonbauteile ohne Querkraftbewehrung und mit verschiedenen Querkraftbewehrungsarten bilden experimentelle Untersuchungen zum Querkrafttragverhalten an UHPC-Balken mit verschiedener Querkraftbewehrung den Ausgangspunkt der vorliegenden Arbeit. Die experimentellen Untersuchungen beinhalteten zehn Querkraftversuche an UHPC-Balken. Diese Balken waren in Abmessungen und Biegezugbewehrung identisch. Sie unterschieden sich nur in der Art der Querkraftbewehrung. Die Querkraftbewehrungsarten umfassten eine Querkraftbewehrung aus Stahlfasern oder Vertikalstäben, eine kombinierte Querkraftbewehrung aus Stahlfasern und Vertikalstäben und einen Balken ohne Querkraftbewehrung. Obwohl für die in diesem Projekt untersuchten Balken Fasergehalte gewählt wurden, die zu einem entfestigenden Nachrissverhalten des Faserbetons führten, zeigten die Balkenversuche, dass die Zugabe von Stahlfasern die Querkrafttragfähigkeit steigerte. Durch die gewählte Querkraftbewehrungskonfiguration bei ansonsten identischen Balken konnte außerdem eine quantitative Abschätzung der einzelnen Traganteile aus den Versuchen abgeleitet werden. Der profilierte Querschnitt ließ einen großen Einfluss auf das Querkrafttragverhalten im Nachbruchbereich erkennen. Ein relativ stabiles Lastniveau nach Erreichen der Höchstlast konnte einer Vierendeelwirkung zugeordnet werden. Auf Basis dieser Versuchsergebnisse und analytischer Überlegungen zu vorhandenen Querkraftmodellen wurde ein additiver Modellansatz zur Beschreibung des Querkrafttragverhaltens von UHPCBalken mit einer kombinierten Querkraftbewehrung aus Stahlfasern und Vertikalstäben formuliert. Für die Formulierung der Traganteile des Betonquerschnitts und der konventionellen Querkraftbewehrung wurden bekannte Ansätze verwendet. Für die Ermittlung des Fasertraganteils wurde die Faserwirksamkeit zugrunde gelegt. Das Lastniveau im Nachbruchbereich aus Viendeelwirkung ergibt sich aus geometrischen Überlegungen.