Crystallographic tilt in GaN layers grown by epitaxial lateral overgrowth

The crystallographic tilt in GaN layers grown by epitaxial lateral overgrowth (ELO) on sapphire (0001) substrates was investigated by using double crystal X-ray diffraction (DC-XRD). It was found that ELO GaN stripes bent towards the SiNx mask in the direction perpendicular to seeding lines. Each side of GaN (0002) peak in DC-XRD rocking curves was a broad peak related with the crystallographic tilt. This broad peak split into two peaks (denoted as A and B), and peak B disappeared gradually when the mask began to be removed by selective etching. Only narrow peak A remained when the SiNx mask was removed completely. A model based on these results has been developed to show that there are two factors responsible for the crystallographic tilt: One is the non-uniformity elastic deformation caused by the interphase force between the ELO GaN layer and the SiNx mask. The other is the plastic deformation, which is attributed to the change of the threading dislocations (TDs)-from vertical in the window regions to the lateral in the regions over the mask.

The structure and current-voltage characteristics of multi-sheet InGaN quantum dots grown by a new multi-step method

Multi-sheet InGaN/GaN quantum dots (QDs) were grown successfully by surface passivation processing and low-temperature growth in metalorganic chemical vapor deposition. This method based on the principle of increasing the energy barrier of adatom hopping by surface passivation and low-temperature growth, is quite different from present methods. The InGaN quantum dots in the first layer of about 40-nm-wide and 15-nm-high grown by this method were revealed by atomic force microscopy. The InGaN QDs in upper layer grew bigger. To our knowledge, the current-voltage characteristics of multi-sheet InGaN/GaN QDs were measured for the fist time. Two kinds of resonance-tunneling-current features were observed which were attributed to the low-dimensional localization effect. Some current peaks only appeared in positive voltage for sample due to the non-uniformity of the QDs in the structure. (C) 2002 Elsevier Science B.V. All rights reserved.

Investigation on the origin of crystallographic tilt in lateral epitaxial overgrown GaN using selective etching

The crystallographic tilt of the lateral epitaxial overgrown (LEO) GaN on sapphire Substrate with SiNx mask is investiaated by double crystal X-ray diffraction. Two wing peaks beside the GaN 0002 peak can be observed for the as-grown LEO GaN. During the selective etching of SiNx mask, each wing peak splits into two peaks, one of which disappears as the mask is removed, while the other remains unchanged. This indicates that the crystallographic tilt of the overgrown region is caused not only by the plastic deformation resulted from the bending of threading dislocations, but by the non-uniformity elastic deformation related with the GaN, SiNx interfacial forces. The widths of these two peaks are also studied in this paper. (C) 2002 Elsevier Science B.V. All rights reserved.

Chaotic behavior of pulsating heat pipes

Chaotic behavior of closed loop pulsating heat pipes (PHPs) was studied. The PHPs were fabricated by capillary tubes with outer and inner diameters of 2.0 and 1.20 mm. FC-72 and deionized water were used as the working fluids. Experiments cover the following data ranges: number of turns of 4, 6, and 9, inclination angles from 5 degrees (near horizontal) to 90, (vertical), charge ratios from 50% to 80%, heating powers from 7.5 to 60.0 W. The nonlinear analysis is based on the recorded time series of temperatures on the evaporation, adiabatic, and condensation sections. The present study confirms that PHPs are deterministic chaotic systems. Autocorrelation functions (ACF) are decreased versus time, indicating prediction ability of the system is finite. Three typical attractor patterns are identified. Hurst exponents are very high, i.e., from 0.85 to 0.95, indicating very strong persistent properties of PHPs. Curves of correlation integral versus radius of hypersphere indicate two linear sections for water PHPs, corresponding to both high frequency, low amplitude, and low frequency, large amplitude oscillations. At small inclination angles near horizontal, correlation dimensions are not uniform at different turns of PHPs. The non-uniformity of correlation dimensions is significantly improved with increases in inclination angles. Effect of inclination angles on the chaotic parameters is complex for FC-72 PHPs, but it is certain that correlation dimensions and Kolmogorov entropies are increased with increases in inclination angles. The optimal charge ratios are about 60-70%, at which correlation dimensions and Kolmogorov entropies are high. The higher the heating power, the larger the correlation dimensions and Kolmogorov entropies are. For most runs, large correlation dimensions and Kolmogorov entropies correspond to small thermal resistances, i.e., better thermal performance, except for FC-72 PHPs at small inclination angles of theta < 15 degrees.

黄土高原降雨空间分布的不均匀性研究

根据黄土高原13条流域的降雨资料，分三种雨型即局地强对流条件引起的小范围、短历时、高强度的局地性暴雨（A型暴雨），峰面型降雨夹有局地雷暴性质的较大范围、中历时、中强度暴雨（B型暴雨），峰面型降雨引起的大面积、长历时、低强度暴雨（C型暴雨）；选用流域面雨量离差系数Cv、流域降雨不均匀系数η和流域最大点与最小点降雨量比值系数α三种指标，分析了次降雨空间分布的不均匀性。

基于LBL声信标的AUV快速精确定位

长基线声学定位系统是水下机器人广泛应用的外部导航设备。以对"CR-02"6000m自治水下机器人(简称AUV)技术的深入开发为背景,提出在原有长基线(LBL)定位系统的基础上增加导航功能的方案。由于海水介质非均匀性与复杂的时空变化特性,给基于测距的位置计算带来很大困难。采用平均声速法计算耗时小而误差大,波阵面定位法误差小而耗时大。为解决这个矛盾,根据AUV深度传感器给出的深度信息,采用本征声线快速计算方法解算AUV的水平面位置。与波阵面法、平均声速法进行了综合比较。仿真实验表明该方法具有优良的性能,满足AUV导航需要。

电离层胶片频高图数字化转换与分析研究

The ionogram acquired with the ionospheric vertical sounding method is the oldest data in the history of ionospheric research. Using of modern microelectronics and computer technology to digitalize, analyse and preserve the huge amount of historical film ionogram has become more and more important and urgent. This paper introduced the progress of the film ionogram digitalization by using digital image processing technologies to correct and repair film ionogram and convert them in an exchangeable format. An analysis and conversion software, basing on this method, has been developed for the film ionogram analysis, and then it introduces the application of this software by combining the SAO Explorer program for Wuhan film ionogram and pseudo-color ionogram in Yamagawa in Japan. It shows that our method is reliable，and the developed software is used friendly and provides a positive solution in digitalization and analysis of huge amount of historical film ionogram. Firstly, we briefly introduce the film ionogram and the process of its digitalization. By observing a amount of film ionogram, we obtain some common characteristics of the digitalized film ionogram following as: (1) the image rotation are caused by scanning; (2) the vertical axis of a large number of film ionogram exist more or less tilt and bending ; (3) coordinates of the film ionogram appear the non-uniformity phenomena result from the instability of driving motor rotation and the error of altitudinal cursor orientation. Moreover, based on the characteristics of the film ionogram and the SAO Explorer software which is widely used for the digital ionogram analysis in the world, a new method has been developed for film ionogram procession. The method contains the image geometric correction and film ionogram format conversion. The image geometric correction includes such as image rotation correction, vertical correction and coordinates scale correction. After geometric correction, the BMP file format images will be converted to the SBF file format images. Then, we also discuss the data format converting methods, which include two methods of the image data mapping basing on the normalization and logarithm, and the method of the preprocessing of the noise filtering and the threshold setting. Combining with SAO Explorer software, we successfully obtain ionospheric parameters and electron profile from the converted SBF file format digital ionograms. Based on the above method, we developed the software for the film ionogram to realize its correction analysis and conversion of the image format, and then give a introduction for its function and operation. Subsequently, the software are applied into the Wuhan film ionogram which separately observed in the high solar activity year and the low in 1980s last century. The results reveal the converted SBF digital ionogram almost preserve the all echo information of the film ionogram. Furthermore, we expressly discuss the application to the Wuhan film ionogram in 1958 in order to validate the applicability and credibility of the software. And it is showed that the important information of the film ionogram are maintained into the SBF digital ionogram. It is represented that there is credibility for conversion of the software when it applied in the older film ionogram. In sum, this software could apply to the digitalization and analysis of huge amount of historical film ionogram. Last, we extended the function of the software by bring some new conversion method and used it to apply to the pseudo-color ionogram of yamagawa in Japan. The results show that the converted ionogram information basically maintain the importantly ionogram information and the error of scaling of converted SBF file format image is almost acceptable, though there is no preprocessing for the original ionogram. Hence, we could extend the applicable range of the software and apply it to all kinds of simulative ionogram imaging by improving the method and software.

油气流线模拟方法研究与系统研制

The modeling of petroleum flow path (petroleum charging) and the detail of corresponding software development are presented in this paper, containing principle of petroleum charging, quantitative method, and practical modeling in two oil fields. The Modeling of Petroleum Flow Path is based on the result of basin modeling, according to the principle of petroleum migrating along the shortest path from the source to trap, Petroleum System Dynamics (Prof. Wu Chonglong, 1998), the concept of Petroleum Migration and Dynamic Accumulation (Zhou Donyan, Li Honhui, 2002), etc. The simulation is done combing with all parameters of basin, and considering the flow potential, non-uniformity of source and porous layer. It's the extending of basin modeling, but not belong to it. It is a powerful simulating tool of petroleum system, and can express quantitatively every kind of geology elements of a petroleum basin, and can recuperate dynamically the geology processes with 3D graphics. At result, we can give a result that the petroleum flow shows itself the phenomena of main path, and without using the special theory such as deflection flow in fractures(Tian Kaiming, 1989, 1994, Zhang Fawang, Hou Xingwei, 1998), and flow potential(England, 1987). The contour map of petroleum flow quantitative show clearly where the coteau - dividing slot is, and which convergence region are the main flow path of petroleum, and where is the favorable play of petroleum. The farsighted trap can be determined if there are enough information about structural diagram and can be evaluated, such as the entrapment extent, spill point, area, oil column thickness, etc. Making full use of the result of basin modeling with this new tool, the critical moment and scheme of the petroleum generation and expulsion can be showed clearly. It's powerful analysis tool for geologist.

Sandstone response to salt weathering following simulated fire damage: a comparison of furnace heating and fire.

Fire has long been recognized as an agent of rock weathering. Our understanding of the impact of fire on stone comes either from early anecdotal evidence, or from more recent laboratory simulation studies, using furnaces to simulate the effects of fire. This paper suggests that knowledge derived from simulated heating experiments is based on the preconceptions of the experiment designer – when using a furnace to simulate fire, the operator decides on the maximum temperature and the duration of the experiment. These are key factors in determining the response of the stone to fire, and if these are removed from realworld observations then knowledge based on these simulations must be questioned. To explore the differences between heating sandstone in a furnace and a real fire, sample blocks of Peakmoor Sandstone were subjected to different stress histories in combination (lime rendering and removal, furnace heating or fire, frost and salt weathering). Block response to furnace heating and fire is discussed, with emphasis placed on the non-uniformity of the fire and of block response to fire in contrast to the uniform response to surface heating in a furnace. Subsequent response to salt weathering (by a 10% solution of sodium chloride and magnesium sulphate) was then monitored by weight loss. Blocks that had experienced fire showed a more unpredictable response to salt weathering than those that had undergone furnace heating – spalling of corners and rapid catastrophic weight loss were evidenced in blocks that had been subjected to fire, after periods of relative quiescence. An important physical side-effect of the fire was soot accumulation, which created a waxy, relatively impermeable layer on some blocks. This layer repelled water and hindered salt ingress, but eventually detached when salt, able to enter the substrate through more permeable areas, concentrated and crystallized behind it, resulting in rapid weight loss and accelerated decay. Copyright ©2007 John Wiley & Sons, Ltd.

Design of a thick-walled screen for flow equalization in microstructured reactors

A systematic computational fluid dynamics (CFD) approach has been applied to design the geometry of the channels of a three-dimensional (thick-walled) screen comprising upstream and downstream sets of elongated channels positioned at an angle of 90 degrees with respect to each other. Such a geometry of the thick-wall screen can effectively drop the ratio of the maximum flow velocity to mean flow velocity below 1.005 in a downstream microstructured reactor at low Reynolds numbers. In this approach the problem of flow equalization reduces to that of flow equalization in the first and second downstream channels of the thick-walled screen. In turn, this requires flow equalization in the corresponding cross-sections of the upstream channels. The validity of the proposed design method was assessed through a case study. The effect of different design parameters on the flow non-uniformity in the downstream channels has been established. The design equation is proposed to calculate the optimum values of the screen parameters. The CFD results on flow distribution were experimentally validated by Laser Doppler Anemometry measurements in the range of Reynolds numbers from 6 to 113. The measured flow non-uniformity in the separate reactor channels was below 2%.

Optimization of heat transfer characteristics, flow distribution, and reaction processing for a microstructured reactor/heat-exchanger for optimal performance in platinum catalyzed ammonia oxidation

The present work is focused on the demonstration of the advantages of miniaturized reactor systems which are essential for processes where potential for considerable heat transfer intensification exists as well as for kinetic studies of highly exothermic reactions at near-isothermal conditions. The heat transfer characteristics of four different cross-flow designs of a microstructured reactor/heat-exchanger (MRHE) were studied by CFD simulation using ammonia oxidation on a platinum catalyst as a model reaction. An appropriate distribution of the nitrogen flow used as a coolant can decrease drastically the axial temperature gradient in the reaction channels. In case of a microreactor made of a highly conductive material, the temperature non-uniformity in the reactor is strongly dependent on the distance between the reaction and cooling channels. Appropriate design of a single periodic reactor/heat-exchanger unit, combined with a non-uniform inlet coolant distribution, reduces the temperature gradients in the complete reactor to less than 4degreesC, even at conditions corresponding to an adiabatic temperature rise of about 1400degreesC, which are generally not accessible in conventional reactors because of the danger of runaway reactions. To obtain the required coolant flow distribution, an optimization study was performed to acquire the particular geometry of the inlet and outlet chambers in the microreactor/heat-exchanger. The predicted temperature profiles are in good agreement with experimental data from temperature sensors located along the reactant and coolant flows. The results demonstrate the clear potential of microstructured devices as reliable instruments for kinetic research as well as for proper heat management in the case of highly exothermic reactions. (C) 2002 Elsevier Science B.V. All rights reserved.

Development of the kinetic model of platinum catalyzed ammonia oxidation in a microreactor

The ammonia oxidation reaction on supported polycrystalline platinum catalyst was investigated in an aluminum-based microreactor. An extensive set of reactions was included in the chemical reactor modeling to facilitate the construction of a kinetic model capable of satisfactory predictions for a wide range of conditions (NH3 partial pressure, 0.01-0.12 atm; O-2 partial pressure, 0.10-0.88 atm; temperature, 523-673 K; contact time, 0.3-0.7 ms). The elementary surface reactions used in developing the mechanism were chosen based on the literature data concerning ammonia oxidation on a Pt catalyst. Parameter estimates for the kinetic model were obtained using multi-response least squares regression analysis using the isothermal plug-flow reactor approximation. To evaluate the model, the behavior of a microstructured reactor was simulated by means of a complete Navier-Stokes model accounting for the reactions on the catalyst surface and the effect of temperature on the physico-chemical properties of the reacting mixture. In this way, the effect of the catalytic wall temperature non-uniformity and the effect of a boundary layer on the ammonia conversion and selectivity were examined. After further optimization of appropriate kinetic parameters, the calculated selectivities and product yields agree very well with the values actually measured in the microreactor. (C) 2002 Elsevier Science B.V. All rights reserved.

A kinetic study of ammonia oxidation on a Pt catalyst in the explosive region in a microstructured reactor/heat-exchanger

The application of an aluminum-based microstructured reactor/heat-exchanger for measuring reaction kinetics in the explosive region is presented. Platinum-catalyzed ammonia oxidation was chosen as a test reaction to demonstrate the feasibility of the method. The reaction kinetics was investigated in a wide range of conditions [NH3 partial pressure: 0.03-0.20 atm, O-2 partial pressure: 0.10-0.88atm; reactant flow 2000-3000 cm(3) min(-1) (STP); temperature 240-360degreesC] over a supported Pt/Al2O3 catalyst (mass of Al2O3 layer in the reactor, 1.95 mg; Pt/Al molar ratio, 0.71; Pt dispersion, 20%). The maximum temperature non-uniformity in the microstructured reactor was ca. 5degreesC, even at conditions corresponding to an adiabatic temperature rise of 1400degreesC. Based on the data obtained, a previous kinetic model for ammonia oxidation was extended. The modified 13-step model describes the data in a considerably wider range of conditions including those with high ammonia loadings and high reaction temperatures. The results indicate the large potential of microstructured devices as reliable tools for kinetic research of highly exothermic reactions.

Numbered-up gas-liquid micro/milli channels reactor with modular flow distributor

Gas-liquid processing in microreactors remains mostly restricted to the laboratory scale due to the complexity and expenditure needed for an adequate numbering-up with a uniform flow distribution. Here, the numbering-up is presented for multi-phase (gas-liquid) flow in microreactor suitable for a production capacity of kg/h. Based on the barrier channels concept, the barrier-based micro/milli reactor (BMMR) is designed and fabricated to deliver flow non-uniformity of less than 10%. The BMMR consists of eight parallel channels all operated in the Taylor flow regime and with a liquid flow rate up to 150. mL/min. The quality of the flow distribution is reported by studying two aspects. The first aspect is the influence of different viscosities, surface tensions and flow rates. The second aspect is the influence of modularity by testing three different reaction channels type: (1) square channels fabricated in a stainless steel plate, (2) square channels fabricated in a glass plate, and (3) circular channels (capillaries) made of stainless steel. Additionally, the BMMR is compared to that of a single channel regard the slug and bubble lengths and bubble generation frequency. The results pave the ground for bringing multi-phase flow in microreactor one step closer for large scale production via numbering-up. © 2012 Elsevier B.V.

Design of a radio frequency heated isothermal micro-trickle bed reactor

A near-isothermal micro-trickle bed reactor operated under radio frequency heating was developed. The reactor bed was packed with nickel ferrite micro-particles of 110. μm diameter, generating heat by the application of RF field at 180. kHz. Hydrodynamics in a co-current configuration was analysed and heat transfer rates were determined at temperature ranging from 55 to 100. °C. A multi-zone reactor bed of several heating and catalytic zones was proposed in order to achieve near-isothermal operations. Exact positioning, number of the heating zones and length of the heating zones composed of a mixture of nickel ferrite and a catalyst were determined by solving a one dimensional model of heat transfer by conduction and convection. The conductive losses contributed up to 30% in the total thermal losses from the reactor. Three heating zones were required to obtain an isothermal length of 50. mm with a temperature non-uniformity of 2. K. A good agreement between the modelling and experimental results was obtained for temperature profiles of the reactor. © 2013 Elsevier B.V.