Produção de amilases de Rhizopus microsporus var. oligosporus e hidrólise enzimática do bagaço de mandioca visando a produção de etanol por Saccharomyces cerevisiae

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Production and characterization of poly-(3-hydroxybutyrate) from recombinant Escherichia coli grown on cheap renewable carbon substrates

Although the biopolymer poly-(3-hydroxybutyrate), P[3HB], presents physicochemical properties that make it an alternative material to conventional plastics, its biotechnological production is quite expensive. As carbon substrates contribute greatly to P[3HB] production cost, the utilization of a cheaper carbon substrate and less demanding micro-organisms should decrease its cost. In the present study a 23 factorial experimental design was applied, aiming to evaluate the effects of using hydrolysed corn starch (HCS) and soybean oil (SBO) as carbon substrates, and cheese whey (CW) supplementation in the mineral medium (MM) on the responses, cell dried weigh (DCW), percentage P[3HB] and mass P[3HB] by recombinant Escherichia coli strains JM101 and DH10B, containing the P[3HB] synthase genes from Cupriavidus necator (ex-Ralstonia eutropha). The analysis of effects indicated that the substrates and the supplement and their interactions had positive effect on CDW. Statistically generated equations showed that, at the highest concentrations of HCS, SO and CW, theoretically it should be possible to produce about 2 g L(1) DCW, accumulating 50% P[3HB], in both strains. To complement this study, the strain that presented the best results was cultivated in MM added to HCS, SBO and CW ( in best composition observed) and complex medium (CM) to compare the obtained P[3HB] in terms of physicochemical parameters. The obtained results showed that the P[3HB] production in MM (1.29 g L(-1)) was approximately 20% lower than in CM (1.63 g L(-1)); however, this difference can be compensated by the lower cost of the MM achieved by the use of cheap renewable carbon sources. Moreover, using differential scanning calorimetry and thermogravimetry analyses, it was observed that the polymer produced in MM was the one which presented physicochemical properties (Tg and Tf) that were more similar to those found in the literature for P[3HB].

Photosynthetic efficiency and rate of CO2 assimilation by Arthrospira (Spirulina) platensis continuously cultivated in a tubular photobioreactor

Similar to other photosynthetic microorganisms, the cyanobacterium Arthrospira platensis can be used to produce pigments, single cell proteins, fatty acids (which can be used for bioenergy), food and feed supplements, and biofixation of CO2. Cultivation in a specifically designed tubular photobioreactor is suitable for photosynthetic biomass production, because the cultivation area can be reduced by distributing the microbial cells vertically, thus avoiding loss of ammonia and CO2. The aim of this study was to investigate the influence of light intensity and dilution rate on the photosynthetic efficiency and CO2 assimilation efficiency of A. platensis cultured in a tubular photobioreactor in a continuous process. Urea was used as a nitrogen source and CO2 as carbon source and for pH control. Steady-state conditions were achieved in most of the runs, indicating that continuous cultivation of this cyanobacterium in a tubular photobioreactor could be an interesting alternative for the large-scale fixation of CO2 to mitigate the greenhouse effect while producing high protein content biomass.

Oxygen supply in Bacillus thuringiensis fermentations: bringing new insights on their impact on sporulation and delta-endotoxin production

The growth kinetics, sporulation, and toxicity of Bacillus thuringiensis var. israelensis were evaluated through the analysis of batch cultures with different dissolved oxygen (DO) profiles. Firstly, DO was maintained constant at 5%, 20%, or 50% throughout fermentation in order to identify the most suitable one to improve the main process parameters. Higher biomass concentration, cell productivity, and cell yield based on glucose were obtained with 50% DO. The higher aeration level also resulted in higher spore counts and markedly improved the toxic activity of the fermentation broth, which was 9-fold greater than that obtained with 5% DO (LC50 of 39 and 329 mg/L, respectively). Subsequently, using a two-stage oxygen supply strategy, DO was kept at 50% during the vegetative and transition phases until the maximum cell concentration was achieved. Then, DO was changed to 0%, 5%, 20%, or 100% throughout sporulation and cell lysis phases. The interruption of oxygen supply strongly reduced the spore production and thoroughly repressed the toxin synthesis. On the contrary, when DO was raised to 100% of saturation, toxic activity increased approximately four times (LC50 of 8.2 mg/L) in comparison with the mean values reached with lower DO levels, even though spore counts were lower than that from the 50% DO assay. When pure oxygen was used instead of normal air, it was possible to obtain 70% of the total biomass concentration achieved in the air assays; however, cultures did not sporulate and the toxin synthesis was consequently suppressed.

Switching the mode of sucrose utilization by Saccharomyces cerevisiae

Abstract Background Overflow metabolism is an undesirable characteristic of aerobic cultures of Saccharomyces cerevisiae during biomass-directed processes. It results from elevated sugar consumption rates that cause a high substrate conversion to ethanol and other bi-products, severely affecting cell physiology, bioprocess performance, and biomass yields. Fed-batch culture, where sucrose consumption rates are controlled by the external addition of sugar aiming at its low concentrations in the fermentor, is the classical bioprocessing alternative to prevent sugar fermentation by yeasts. However, fed-batch fermentations present drawbacks that could be overcome by simpler batch cultures at relatively high (e.g. 20 g/L) initial sugar concentrations. In this study, a S. cerevisiae strain lacking invertase activity was engineered to transport sucrose into the cells through a low-affinity and low-capacity sucrose-H+ symport activity, and the growth kinetics and biomass yields on sucrose analyzed using simple batch cultures. Results We have deleted from the genome of a S. cerevisiae strain lacking invertase the high-affinity sucrose-H+ symporter encoded by the AGT1 gene. This strain could still grow efficiently on sucrose due to a low-affinity and low-capacity sucrose-H+ symport activity mediated by the MALx1 maltose permeases, and its further intracellular hydrolysis by cytoplasmic maltases. Although sucrose consumption by this engineered yeast strain was slower than with the parental yeast strain, the cells grew efficiently on sucrose due to an increased respiration of the carbon source. Consequently, this engineered yeast strain produced less ethanol and 1.5 to 2 times more biomass when cultivated in simple batch mode using 20 g/L sucrose as the carbon source. Conclusion Higher cell densities during batch cultures on 20 g/L sucrose were achieved by using a S. cerevisiae strain engineered in the sucrose uptake system. Such result was accomplished by effectively reducing sucrose uptake by the yeast cells, avoiding overflow metabolism, with the concomitant reduction in ethanol production. The use of this modified yeast strain in simpler batch culture mode can be a viable option to more complicated traditional sucrose-limited fed-batch cultures for biomass-directed processes of S. cerevisiae.

Proceedings of the Fifteenth Annual biochemical Engineering Symposium

This work represents the proceedings of the fifteenth symposium which convened at Colorado State University on May 24, 1985. The two day meeting was scheduled one month later than usual, i.e., after the spring semester, so that travelers from the Midwest (Iowa State University, Kansas State University and University of Missouri) could enjoy the unique mountain setting provided at Pingree Park. The background of the photograph on the cover depicts the beauty of the area. ContentsGreg Sinton and S.M. Leo, KSU. Models for the Biodegration of 2.4-D and Related Xenobiotic Compounds. V. Bringi, CSU. Intrinsic Kinetics from a Novel Immobilized Cell CSTR. Steve Birdsell, CU. Novel Microbial Separation Techniques. Mark Smith, MU. Kinetic Characterization of Growth of E. coli on Glucose. Michael M. Meagher, ISU. Kinetic Parameters of Di- and Trisaccharaide Hydrolysis by Glucoamylase II. G.T. Jones and A.K. Ghosh Hajra, KSU. Modeling and Simulation of Legume Modules with Reactive Cores and Inert Shells. S.A. Patel and C.H. Lee, KSU. Energetic Analysis and Liquid Circulation in an Airlift Fermenter. Rod R. Fisher, ISU. The Effects of Mixing during Acid Addition of Fractionally Precipitated Protein. Mark M. Paige, CSU. Fed-batch Fermentations of Clostridium acetobutylicum. Michael K. Dowd, ISU. A Nonequilibirium Thermodynamic Description of the Variation of Contractile Velocity and Energy Use in Muscle. David D. Drury, CSU. Analysis of Hollow Fiber Bioreactor Performance for MAmmalian Cells by On-Line MMR. H.Y. Lee, KSU. Process Analysis of Photosynthetic Continuous Culture Systems. C.J. Wang, MU. Kinetic Consideration in Fermentation of Cheese Whey to Ethanol.

Proceedings of the Twenty-First Annual Biochemical Engineering Symposium

The 21st Annual Biochemical Engineering Symposium was held at Colorado State University on April 20, 1991. The primary goals of this symposium series are to provide an opportunity for students to present and publish their research work and to promote informal discussions on biochemical engineering research. Contents High Density Fed-Batch Cultivation and Energy Metabolism of Bacillus thuringtensis; W.-M. Liu, V. Bihari, M. Starzak, and R.K. Bajpai Influences of Medium Composition and Cultivation Conditions on Recombinant Protein Production by Bacillus subtilis; K. Park, P.M. Linzmaier, and K.F. Reardon Characterization of a Foreign Gene Expression in a Recombinant T7 Expression System Infected with λ Phages; F. Miao and D.S. Kompala Simulation of an Enzymatic Membrane System with Forced Periodic Supply of Substrate; N. Nakaiwa, M. Yashima, L.T. Fan, and T. Ohmori Batch Extraction of Dilut Acids in a Hollow Fiber Module; D.G. O'Brien and C.E. Glatz Evaluation of a New Electrophoretic Device for Protein Purification; M.-J. Juang and R.G. Harrison Crossflow Microfiltration and Membrane Fouling for Yeast Cell Suspension; S. Redkar and R. Davis Interaction of MBP-β-Galactosidase Fusion Protein with Starch; L. Taladriz and Z. Nikolov Predicting the Solubility of Recombinant Proteins in Escherichia coli; D.L. Wilkinson and R.G. Harrison Evolution of a Phase-Separated, Gravity-Independent Bioractor; P.E. Villeneuve and E.H. Dunlop A Strategy for the Decontamination of Soils Containing Elevated Levels of PCP; S. Ghoshal, S. K. Banelji, and RK. Bajpai Practical Considerations for Implementation of a Field Scale In-Situ Bioremediation Project; J.P. McDonald, CA Baldwin, and L.E. Erickson Parametric Sensitivity Studies of Rhizopus oligosporus Solid Substrate Fermentation; J. Sargantanis, M.N. Karim, and V.G. Murphy, and RP. Tengerdy Production of Acetyl-Xylan Esterase from Aspergillus niger; M.R Samara and J.C. Linden Biological and Latex Particle Partitioning in Aqueous Two-Phase Systems; D.T.L. Hawker, RH. Davis, P.W. Todd, and R Lawson Novel Bioreactor /Separator for Microbial Desulfurization of Coal; H. Gecol, RH. Davis, and J .R Mattoon Effect of Plants and Trees on the Fate, Transport and Biodegradation of Contaminants in the Soil and Ground Water; W. Huang, E. Lee, J.F. Shimp, L.C. Davis, L.E. Erickson, and J.C. Tracy Sound Production by Interfacial Effects in Airlift Reactors; J. Hua, T.-Y. Yiin, LA Glasgow, and L.E. Erickson Soy Yogurt Fermentation of Rapid Hydration Hydrothermal Cooked Soy Milk; P. Tuitemwong, L.E. Erickson, and D.Y.C. Fung Influence of Carbon Source on Pentachlorophenol Degradation by Phanerochaete chrysosportum in Soil; C.-Y.M. Hsieh, RK. Bajpai, and S.K. Banerji Cellular Responses of Insect Cells Spodopiera frugiperda -9 to Hydrodynamic Stresses; P.L.-H. Yeh and RK. Bajpa1 A Mathematical Model for Ripening of Cheddar Cheese; J. Kim, M. Starzak, G.W. Preckshoi, and R.K. Bajpai

Produção de biohidrogênio a partir de soro de leite em AnSBBR com recirculação da fase líquida

O presente estudo investigou a aplicação de dois tipos de AnSBBR (reatores anaeróbio com biofilme e operados em batelada e batelada alimentada sequenciais: com recirculação da fase líquida e com agitação) para produção de biohidrogênio tratando água residuária sintética (a base de soro de leite e lactose, respectivamente). O AnSBBR com recirculação da fase líquida, que foi o estudo principal do presente trabalho, apresentou problemas na produção de hidrogênio utilizando soro de leite como substrato. Algumas alternativas, como adaptação da biomassa com substratos puros de degradação mais fácil, controle do pH em valores muito baixos e diferentes formas de inoculação foram testadas, entretanto, sem obtenção de sucesso. A solução do problema foi obtida ao refrigerar o meio de alimentação a 4ºC para evitar a fermentação no frasco de armazenamento, retirar a ureia e a suplementação de nutrientes, e realizar lavagens periódicas do material suporte para retirada de parte da biomassa. Dessa forma eliminaram-se indícios de produção de H2S por possível ação de bactérias redutoras de sulfato (BRS) e atingiu-se uma produção estável de hidrogênio sem, entretanto, eliminar completamento o metano, que foi produzido em baixas concentrações. Depois de atingida a estabilidade, investigou-se a influência da concentração afluente de substrato, do tempo de enchimento e da temperatura na produção de biohidrogênio no AnSBBR com recirculação da fase líquida tratando soro de leite. O estudo da concentração afluente apresentou um ponto ótimo para a concentração de 5400 mgDQO.L-1, atingindo valores de 0,80 mol H2.mol-1 lactose e de 660 mL H2.L-1.d-1. O estudo do tempo de enchimento apresentou resultados similares para as condições analisadas. Com relação à temperatura, os melhores resultados foram obtidos com a temperatura mais baixa testada de 15ºC (1,12 mol H2.mol lactose-1 e 1080 mL H2.L-1.d-1), sendo que na temperatura mais alta testada (45°C) não ocorreu produção de hidrogênio. Para o AnSBBR com agitação mecânica, que foi um estudado complementar realizado pelo fato da lactose ser o principal complemento do soro de leite, o desempenho do biorreator foi avaliado de acordo com influência conjunta do tempo de ciclo (tC – 2, 3 e 4 h), da concentração afluente (CSTA – 3600-5400 mgDQO.L-1) e da carga orgânica volumétrica aplicada (COAV – 9,3, 12,3, 13,9, 18,5 e 27,8 mgDQO.L-1.d-1). Foram obtidos excelentes resultados: consumos de carboidratos (lactose), com valores médios sempre acima de 90% e uma produção estável de biohidrogênio em todas as condições estudadas, com metano em baixas concentrações apenas na condição de maior COAV. A diminuição do tC apresentou tendência clara de melhora sobre o RMCRC,n (rendimento molar entre hidrogênio produzido e carboidrato removido) apenas para as condições com menor concentração CSTA, havendo uma relação direta entre CSTA, e RMCRC,n em todos os valores de tC, exceto para o tempo de ciclo de 3 h, exatamente onde ocorreu produção de metano. O melhor valor de RMCRC,n obtido na operação com lactose (1,65 mol H2.mol Carboidrato-1) foi superior aos obtidos em outros trabalhos utilizando a mesma configuração de reator e sacarose como substrato. As análises filogenéticas mostraram que a maioria dos clones analisados foi semelhante à Clostridium. Além destes, clones filogeneticamente semelhantes com a Família Lactobacilaceae, especificamente Lactobacillus rhamnosus foram observados em menor porcentagem no reator, assim como clones com sequências semelhantes a Acetobacter indonesiensis.

Growth, viral production and metabolism of a Helicoverpa zea cell line in serum-free culture

Insect cell cultures have been extensively utilised for means of production for heterologous proteins and biopesticides. Spodoptera frugiperda (Sf9) and Trichoplusia ni (High Five(TM)) cell lines have been widely used for the production of recombinant proteins, thus metabolism of these cell lines have been investigated thoroughly over recent years. The Helicoverpa zea cell line has potential use for the production of a biopesticide, specifically the Helicoverpa armigera single-nucleocapsid nucleopolyhedrovirus (HaSNPV). The growth, virus production, nutrient consumption and waste production of this cell line was investigated under serum-free culture conditions, using SF900II and a low cost medium prototype (LCM). The cell growth ( growth rates and population doubling time) was comparable in SF900II and LCM, however, lower biomass and cell specific virus yields were obtained in LCM. H. zea cells showed a preference for asparagine over glutamine, similar to the High Five(TM) cells. Ammonia was accumulated to significantly high levels (16 mM) in SF900II, which is an asparagine and glutamine rich medium. However, given the absence of asparagine and glutamine in the medium ( LCM), H. zea cells adapted and grew well in the absence of these substrates and no accumulation of ammonia was observed. The adverse effect of ammonia on H. zea cells is unknown since good production of biologically active HaSNPV was achieved in the presence of high ammonia levels. H. zea cells showed a preference for maltose even given an abundance supply of free glucose. Accumulation of lactate was observed in H. zea cell cultures.

Bioreaction and separation in preparative batch chromatographic columns : the hydrology of lactose to yield glucose,galactose and oligosaccharides

The initial aim of this project was to improve the performance of a chromatographic bioreactor-separator (CBRS). In such a system, a dilute enzyme solution is pumped continuously through a preparative chromatographic column, while pulses of substrate are periodically injected on to the column. Enzymic reaction and separation are therefore performed in a single unit operation. The chromatographic columns used were jacketed glass columns ranging from 1 to 2 metres long with an internal diameter of 1.5 cm. Linking these columns allowed 1, 2, 3 and 4 metre long CBRS systems to be constructed. The hydrolysis of lactose in the presence of β~galactosidase was the reaction of study. From previous work at Aston University, there appeared to be no difficulties in achieving complete lactose hydrolysis in a CBRS. There did, however, appear to be scope for improving the separative performance, so this was adopted as an initial goal. Reducing the particle size of the stationary phase was identified as a way of achieving this improvement. A cation exchange resin was selected which had an average particle size of around half that previously used when studying this reaction. A CBRS system was developed which overcame the operational problems (such as high pressure drop development) associated with use of such a particle size. A significant improvement in separative power was achieved. This was shown by an increase in the number of theoretical plates (N) from about 500 to about 3000 for a 2 metre long CBRS, coupled with higher resolution. A simple experiment with the 1 metre column showed that combined bioreaction and separation was achievable in this system. Having improved the separative performance of the system, the factors affecting enzymic reaction in a CBRS were investigated; including pulse volume and the degree of mixing between enzyme and substrate. The progress of reaction in a CBRS was then studied. This information was related to the interaction of reaction and separation over the reaction zone. The effect of injecting a pulse over a length of time as in CBRS operation was simulated by fed batch experiments. These experiments were performed in parallel with normal batch experiments where the substrate is mixed almost instantly with the enzyme. The batch experiments enabled samples to be taken every minute and revealed that reaction is very rapid. The hydrodynamic characteristics of the two injector configurations used in CBRS construction were studied using Magnetic Resonance Imaging, combined with hydrodynamic calculations. During the optimisation studies, galactooligosaccharides (GOS) were detected as intermediates in the hydrolysis process. GOS are valuable products with potential and existing applications in food manufacture (as nutraceuticals), medicine and drug targeting. The focus of the research was therefore turned to GOS production. A means of controlling reaction to arrest break down of GOS was required. Raising temperature was identified as a possible means of achieving this within a CBRS. Studies were undertaken to optimise the yield of oligosaccharides, culminating in the design, construction and evaluation of a Dithermal Chromatographic Bioreactor-separator.

Characterisation of a harvesting step for monoclonal antibodies from mammalian cell culture

The focus of this research was defined by a poorly characterised filtration train employed to clarify culture broth containing monoclonal antibodies secreted by GS-NSO cells: the filtration train blinded unpredictably and the ability of the positively charged filters to adsorb DNA from process material was unknown. To direct the development of an assay to quantify the ability of depth filters to adsorb DNA, the molecular weight of DNA from a large-scale, fed-batch, mammalian cell culture vessel was evaluated as process material passed through the initial stages of the purification scheme. High molecular weight DNA was substantially cleared from the broth after passage through a disc stack centrifuge and the remaining low molecular weight DNA was largely unaffected by passage through a series of depth filters and a sterilising grade membrane. Removal of high molecular weight DNA was shown to be coupled with clarification of the process stream. The DNA from cell culture supernatant showed a pattern of internucleosomal cleavage of chromatin when fractionated by electrophoresis but the presence of both necrotic and apoptotic cells throughout the fermentation meant that the origin of the fragmented DNA could not be unequivocally determined. An intercalating fluorochrome, PicoGreen, was elected for development of a suitable DNA assay because of its ability to respond to low molecular weight DNA. It was assessed for its ability to determine the concentration of DNA in clarified mammalian cell culture broths containing pertinent monoclonal antibodies. Fluorescent signal suppression was ameliorated by sample dilution or by performing the assay above the pI of secreted IgG. The source of fluorescence in clarified culture broth was validated by incubation with RNase A and DNase I. At least 89.0 % of fluorescence was attributable to nucleic acid and pre-digestion with RNase A was shown to be a requirement for successful quantification of DNA in such samples. Application of the fluorescence based assay resulted in characterisation of the physical parameters governing adsorption of DNA by various positively charged depth filters and membranes in test solutions and the DNA adsorption profile of the manufacturing scale filtration train. Buffers that reduced or neutralised the depth filter or membrane charge, and those that impeded hydrophobic interactions were shown to affect their operational capacity, demonstrating that DNA was adsorbed by a combination of electrostatic and hydrophobic interactions. Production-scale centrifugation of harvest broth containing therapeutic protein resulted in the reduction of total DNA in the process stream from 79.8 μg m1-1 to 9.3 μg m1-1 whereas the concentration of DNA in the supernatant of pre-and post-filtration samples had only marginally reduced DNA content: from 6.3 to 6.0 μg m1-1 respectively. Hence the filtration train was shown to ineffective in DNA removal. Historically, blinding of the depth filters had been unpredictable with data such as numbers of viable cells, non-viable cells, product titre, or process shape (batch, fed-batch, or draw and fill) failing to inform on the durability of depth filters in the harvest step. To investigate this, key fouling contaminants were identified by challenging depth filters with the same mass of one of the following: viable healthy cells, cells that had died by the process of apoptosis, and cells that had died through the process of necrosis. The pressure increase across a Cuno Zeta Plus 10SP depth filter was 2.8 and 16.5 times more sensitive to debris from apoptotic and necrotic cells respectively, when compared to viable cells. The condition of DNA released into the culture broth was assessed. Necrotic cells released predominantly high molecular weight DNA in contrast to apoptotic cells which released chiefly low molecular weight DNA. The blinding of the filters was found to be largely unaffected by variations in the particle size distribution of material in, and viscosity of, solutions with which they were challenged. The exceptional response of the depth filters to necrotic cells may suggest the cause of previously noted unpredictable filter blinding whereby a number of necrotic cells have a more significant impact on the life of a depth filter than a similar number of viable or apoptotic cells. In a final set of experiments the pressure drop caused by non-viable necrotic culture broths which had been treated with DNase I or benzonase was found to be smaller when compared to untreated broths: the abilities of the enzyme treated cultures to foul the depth filter were reduced by 70.4% and 75.4% respectively indicating the importance of DNA in the blinding of the depth filter studied.

Panossyöttökasvatusprosessin automatisointi

Tutkimuskäyttöön tarkoitettujen rekombinanttiproteiinien tuottaminen fermentoimalla on yleinen menetelmä bioteollisuudessa. Mikrobit kasvatetaan fermentorissa, joka tarjoaa kontrolloidun kasvuympäristön ja sopivat tuotto-olosuhteet halutulle tuotteelle. Eräs fermentointimuodoista on korkeatuottoinen ja pitkäkestoinen panossyöttökasvatus, jossa saavutetaan panoskavatusta merkittävästi korkeampi solutiheys jatkamalla panosvaiheen jälkeen kasvua rajoittavan substraatin syöttöä. Laboratoriomittakaavassa fermentorikasvatusten tilavuudet vaihtelevat litrasta kymmeniin ja niissä kasvatusta seurataan sekä ohjataan joko fermentorista tai tietokoneesta. Tyypillisessä fermentointiprosessissa operaattori tarkkailee muun muassa vaahdonkorkeutta sekä käynnistää pumppuja olosuhteiden muuttuessa. Tällaiset tehtävät ovat teollisen mittakaavan laitteistoissa usein automatisoituja. Diplomityön tarkoituksena oli päivittää kahden Turun yliopiston biotekniikan laboratoriossa sijaitsevan BioFlo® -sarjan pöytäfermentorin MS-DOS -pohjainen tietokoneohjausohjelma nykyaikaiseksi ja lisätä siihen etäseuranta ja -ohjaus. Ohjelmaan oli tarkoitus liittää erillinen optinen solutiheysanturi, jonka lukemien häiriötä haluttiin myös vähentää signaalinkäsittelyllä. Lisäksi vaahdonestoaineen ja indusorin lisäykset haluttiin automatisoida panossyöttökasvatuksessa. Vaahdonkorkeuden havaitsemisen mahdollisuutta konenäön menetelmin haluttiin selvittää, jotta vaahdonestoaineen automaattiset lisäykset voitaisiin toteuttaa nettikameran syötteen perusteella. Koekasvatuksilla osoitettiin päivitetyn ohjausohjelman toimivan panos- ja panossyöttömuodoilla. Uuden käyttöliittymän avulla pystyttiin automatisoimaan panoskasvatuksen lisäykset ja syöttönopeuden muutokset sekä tunnistamaan kasvatusliuosten vaahdonkorkeutta vaahdonestoaineen lisäykseen riittävällä kahden senttimetrin tarkkuudella. Lisäksi käyttöliittymä mahdollisti kasvatuksen ohjauksen ja seurauksen myös etänä. Työssä kehitetty ohjausohjelma julkaistiin avoimena ohjelmana ilman etä- ja nettikameratoimintoja. Ohjelma toimii hyvin BioFlo® -sarjan fermentorien käyttöliittymänä, mutta avoimen lähdekoodin ansiosta kuka tahansa voi hyödyntää ohjelmaa pohjana myös uusissa projekteissa tai muissa fermentorimalleissa.

High-level expression of Rhodotorula gracilis d-amino acid oxidase in Pichia pastoris

By combining gene design and heterologous over-expression of Rhodotorula gracilis D-amino acid oxidase (RgDAO) in Pichia pastoris, enzyme production was enhanced by one order of magnitude compared to literature benchmarks, giving 350 kUnits/l of fed-batch bioreactor culture with a productivity of 3.1 kUnits/l h. P. pastoris cells permeabilized by freeze-drying and incubation in 2-propanol (10% v/v) produce a highly active (1.6 kUnits/g dry matter) and stable oxidase preparation. Critical bottlenecks in the development of an RgDAO catalyst for industrial applications have been eliminated.

Stepwise engineering of a Pichia pastoris D-amino acid oxidase whole cell catalyst

Trigonopsis variabilis D-amino acid oxidase (TvDAO) is a well characterized enzyme used for cephalosporin C conversion on industrial scale. However, the demands on the enzyme with respect to activity, operational stability and costs also vary with the field of application. Processes that use the soluble enzyme suffer from fast inactivation of TvDAO while immobilized oxidase preparations raise issues related to expensive carriers and catalyst efficiency. Therefore, oxidase preparations that are more robust and active than those currently available would enable a much broader range of economically viable applications of this enzyme in fine chemical syntheses. A multi-step engineering approach was chosen here to develop a robust and highly active Pichia pastoris TvDAO whole-cell biocatalyst. As compared to the native T. variabilis host, a more than seven-fold enhancement of the intracellular level of oxidase activity was achieved in P. pastoris through expression optimization by codon redesign as well as efficient subcellular targeting of the enzyme to peroxisomes. Multi copy integration further doubled expression and the specific activity of the whole cell catalyst. From a multicopy production strain, about 1.3 x 103 U/g wet cell weight (wcw) were derived by standard induction conditions feeding pure methanol. A fed-batch cultivation protocol using a mixture of methanol and glycerol in the induction phase attenuated the apparent toxicity of the recombinant oxidase to yield final biomass concentrations in the bioreactor of >or= 200 g/L compared to only 117 g/L using the standard methanol feed. Permeabilization of P. pastoris using 10% isopropanol yielded a whole-cell enzyme preparation that showed 49% of the total available intracellular oxidase activity and was notably stabilized (by three times compared to a widely used TvDAO expressing Escherichia coli strain) under conditions of D-methionine conversion using vigorous aeration. Stepwise optimization using a multi-level engineering approach has delivered a new P. pastoris whole cell TvDAO biocatalyst showing substantially enhanced specific activity and stability under operational conditions as compared to previously reported preparations of the enzyme. The production of the oxidase through fed-batch bioreactor culture and subsequent cell permeabilization is high-yielding and efficient. Therefore this P. pastoris catalyst has been evaluated for industrial purposes.

Model-based analysis and optimization of bioreactor for hematopoietic stem cell cultivation

One of the problems to be solved in attaining the full potentials of hematopoietic stem cell (HSC) applications is the limited availability of the cells. Growing HSCs in a bioreactor offers an alternative solution to this problem. Besides, it also offers the advantages of eliminating labour intensive process as well as the possible contamination involved in the periodic nutrient replenishments in the traditional T-flask stem cell cultivation. In spite of this, the optimization of HSC cultivation in a bioreactor has been barely explored. This manuscript discusses the development of a mathematical model to describe the dynamics in nutrient distribution and cell concentration of an ex vivo HSC cultivation in a microchannel perfusion bioreactor. The model was further used to optimize the cultivation by proposing three alternative feeding strategies in order to prevent the occurrence of nutrient limitation in the bioreactor. The evaluation of these strategies, the periodic step change increase in the inlet oxygen concentration, the periodic step change increase in the media inflow, and the feedback control of media inflow, shows that these strategies can successfully improve the cell yield of the bioreactor. In general, the developed model is useful for the design and optimization of bioreactor operation.