K-Ar ages of biotite and muscovite from Pangong metamorphic complex, Shyok suture zone, India: Implications for the youngest post-collision metamorphic event in Ladakh Himalaya

The garnet-kyanite-staurolite and garnet-biotite-staurolite gneisses were collected from a locality within Lukung area that belongs to the Pangong metamorphic complex in Shyok valley, Ladakh Himalaya. The kyanite-free samples have garnet and staurolite in equilibrium, where garnets show euhedral texture and have flat compositional profile. On the other hand, the kyanite-bearing sample shows equilibrium assemblage of garnet-kyanite-staurolite along with muscovite and biotite. In this case, garnet has an inclusion rich core with a distinct grain boundary, which was later overgrown by inclusion free euhedral garnet. Garnet cores are rich in Mn and Ca, while the rims are poor in Mn and rich in Fe and Mg, suggesting two distinct generations of growth. However, the compositional profiles and textural signature of garnets suggests the same stage of P -T evolution for the formation of the inclusion free euhedral garnets in the kyanite-free gneisses and the inclusion free euhedral garnet rims in the kyanite-bearing gneiss. Muscovites from the four samples have consistent K-Ar ages, suggesting the cooling age (∼ 10 Ma) of the gneisses. These ages make a constraint on the timing of the youngest post-collision metamorphic event that may be closely related to an activation of the Karakoram fault in Pangong metamorphic complex.

Planning neighbourhoods for all ages and abilities: A multi-generational perspective

Taking a more integrated approach to planning our neighbourhoods for the continuum of inhabitants’ ages and abilities makes sense given our current and future population composition. Seldom are the built environment requirements of diverse groups (e.g. children, seniors, and people with disability) synthesised, resulting in often unfriendly and exclusionary neighbourhoods. This often means people experience barriers or restriction on their freedom to move about and interact within their neighbourhood. Applying universal design to neighbourhoods may provide a bridging link. By presenting two cases from South-East Queensland (SEQ), Australia, through the lenses of different ages and abilities - older children with physical disabilities and their families (Stafford 2013, 2014) and seniors (Baldwin et al. 2012), we intend to increase recognition of users' needs and stimulate the translation of knowledge to the practice of planning inclusive neighbourhoods.

Self-interrupted regenerative metal cutting in turning

A new approach is used to study the global dynamics of regenerative metal cutting in turning. The cut surface is modeled using a partial differential equation (PDE) coupled, via boundary conditions, to an ordinary differential equation (ODE) modeling the dynamics of the cutting tool. This approach automatically incorporates the multiple-regenerative effects accompanying self-interrupted cutting. Taylor's 3/4 power law model for the cutting force is adopted. Lower dimensional ODE approximations are obtained for the combined tool–workpiece model using Galerkin projections, and a bifurcation diagram computed. The unstable solution branch off the subcritical Hopf bifurcation meets the stable branch involving self-interrupted dynamics in a turning point bifurcation. The tool displacement at that turning point is estimated, which helps identify cutting parameter ranges where loss of stability leads to much larger self-interrupted motions than in some other ranges. Numerical bounds are also obtained on the parameter values which guarantee global stability of steady-state cutting, i.e., parameter values for which there exist neither unstable periodic motions nor self-interrupted motions about the stable equilibrium.

Determinants of institutional care at older ages in Finland

Väitöskirjassa selvitettiin ikäihmisten laitoshoitoon siirtymisen todennäköisyyttä ja sen taustoja kansainvälisesti ainutlaatuisen rekisteriaineiston avulla. Selvitettäviä asioita olivat eri sairauksien, sosioekonomisten tekijöiden, puolison olemassaolon ja leskeksi jäämisen yhteys laitoshoitoon siirtymiseen yli 65-vuotiailla suomalaisilla. Tutkimuksessa havaittiin, että dementia, Parkinsonin tauti, aivohalvaus, masennusoireet ja muut mielenterveysongelmat, lonkkamurtuma sekä diabetes lisäsivät ikäihmisten todennäköisyyttä siirtyä laitoshoitoon yli 50 prosentilla, kun muut sairaudet ja sosiodemografiset tekijät oli otettu huomioon. Korkeat tulot vähensivät laitoshoidon todennäköisyyttä, kun taas puutteellinen asuminen (ilman peseytymistiloja tai keskus- tai sähkölämmitystä) sekä erittäin puutteellinen asuminen (ilman lämmintä vettä, vesijohtoa, viemäriä tai vesivessaa) lisäsivät todennäkösyyttä, kun muut sosiodemografiset tekijät, sairaudet ja asuinalue oli huomioitu. Kerrostalon hissittömyys ei ollut yhteydessä laitoshoidon todennäköisyyteen. Todennäköisyys siirtyä laitoshoitoon oli jostain syystä korkeampaa niillä ikäihmisillä, jotka asuivat vuokralla ja matalampaa omakotitalossa asuvilla ja niillä, joilla oli auto. Puolison olemassaolo vähensi ja leskeksi jääminen lisäsi laitoshoidon todennäköisyyttä huomattavasti. Todennäköisyys oli erityisen suuri, yli kolminkertainen, kun puolison kuolemasta oli kulunut enintään kuukausi verrattuna niihin, joiden puoliso oli elossa. Todennäköisyys laski, kun puolison kuolemasta kului aikaa. Miesten ja naisten tulokset olivat samansuuntaisia. Korkeat tulot tai koulutus eivät suojanneet riskiltä joutua laitoshoitoon puolison kuoltua. Puolison kuolema näyttää lisäävän hoidon tarvetta, kun kotona ei ole enää puolisoa tukemassa ja huolehtimassa kodin askareista. Laitoshoidon tarve vähenee, jos ja kun lesket ajan kuluessa oppivat elämään yksin. Toisaalta tutkimustulokset saattavat viitata myös siihen, että kaikkein huonokuntoisimmat lesket, jotka eivät pärjää yksin asuessaan, siirtyvät laitoshoitoon hyvin nopeasti puolison kuoltua. Tutkimuksessa oli mukana yhteensä yli 280 000 yli 65-vuotiasta henkilöä, joiden pitkäaikaiseen laitoshoitoon siirtymistä seurattiin tammikuusta 1998 syyskuuhun 2003. Laitoshoidoksi määriteltiin terveyskeskuksissa, sairaaloissa ja vanhainkodeissa tai vastaavissa yksiköissä tapahtuva pitkäaikainen hoito, joka kesti yli 90 vuorokautta tai oli vahvistettu pitkäaikaishoidon päätöksellä. Tutkimuksessa käytetty aineisto koottiin väestörekistereistä, sosiaali- ja terveydenhuollon rekistereistä ja lääkerekistereistä.

Experimental estimation of friction force in lubricated cutting of steel

Friction force generated in lubricated cutting of steel is experimentally estimated by recording the tangential force experienced by the spherical face of a pin rubbing against a freshly cut surface. The pin and the cutting tool are both submerged in the lubricant and the pin is situated on the cut-track to record the force. The recording shows an instantaneous achievement of a peak in the force curve followed by a decline in time to a steady state value. The peak and not the steady state friction was found to be sensitive to the structure of the hydrocarbon and addition of additive to the oil. The configuration was designed and tested to demonstrate the influence of a reaction film which develops during cutting, on cutting tool friction. Given the strong correlation between the peak friction and the existence of a tribofilm in the cutting zone, the configuration is used to determine the lower limit of a cutting speed regime, which marks the initiation of lubricant starvation, in cutting of steel using an emulsion as a cutting fluid. (C) 2010 Elsevier B.V. All rights reserved.

Estimation of cutting volume with three inventory methods for harvest planning in Canadian boreal forests.

Two methods of pre-harvest inventory were designed and tested on three cutting sites containing a total of 197 500 m3 of wood. These sites were located on flat-ground boreal forests located in northwestern Quebec. Both methods studied involved scaling of trees harvested to clear the road path one year (or more) prior to harvest of adjacent cut-blocks. The first method (ROAD) considers the total road right-of-way volume divided by the total road area cleared. The resulting volume per hectare is then multiplied by the total cut-block area scheduled for harvest during the following year to obtain the total estimated cutting volume. The second method (STRATIFIED) also involves scaling of trees cleared from the road. However, in STRATIFIED, log scaling data are stratified by forest stand location. A volume per hectare is calculated for each stretch of road that crosses a single forest stand. This volume per hectare is then multiplied by the remaining area of the same forest stand scheduled for harvest one year later. The sum of all resulting estimated volumes per stand gives the total estimated cutting-volume for all cut-blocks adjacent to the studied road. A third method (MNR) was also used to estimate cut-volumes of the sites studied. This method represents the actual existing technique for estimating cutting volume in the province of Quebec. It involves summing the cut volume for all forest stands. The cut volume is estimated by multiplying the area of each stand by its estimated volume per hectare obtained from standard stock tables provided by the governement. The resulting total estimated volume per cut-block for all three methods was then compared with the actual measured cut-block volume (MEASURED). This analysis revealed a significant difference between MEASURED and MNR methods with the MNR volume estimate being 30 % higher than MEASURED. However, no significant difference from MEASURED was observed for volume estimates for the ROAD and STRATIFIED methods which respectively had estimated cutting volumes 19 % and 5 % lower than MEASURED. Thus the ROAD and STRATIFIED methods are good ways to estimate cut-block volumes after road right-of-way harvest for conditions similar to those examined in this study.

Infinite dimensional slow modulations in a well known delayed model for cutting tool vibrations

We apply the method of multiple scales (MMS) to a well-known model of regenerative cutting vibrations in the large delay regime. By ``large'' we mean the delay is much larger than the timescale of typical cutting tool oscillations. The MMS up to second order, recently developed for such systems, is applied here to study tool dynamics in the large delay regime. The second order analysis is found to be much more accurate than the first order analysis. Numerical integration of the MMS slow flow is much faster than for the original equation, yet shows excellent accuracy in that plotted solutions of moderate amplitudes are visually near-indistinguishable. The advantages of the present analysis are that infinite dimensional dynamics is retained in the slow flow, while the more usual center manifold reduction gives a planar phase space; lower-dimensional dynamical features, such as Hopf bifurcations and families of periodic solutions, are also captured by the MMS; the strong sensitivity of the slow modulation dynamics to small changes in parameter values, peculiar to such systems with large delays, is seen clearly; and though certain parameters are treated as small (or, reciprocally, large), the analysis is not restricted to infinitesimal distances from the Hopf bifurcation.

Comparison of CVD and MOCVD-grown Al2O3 coatings in the performance of cemented carbide cutting tool inserts

Low-pressure MOCVD, with tris(2,4 pentanedionato)aluminum(III) as the precursor, was used in the present investigation to coat alumina on to cemented carbide cutting tools. To evaluate the MOCVD process, the efficiency in cutting operations of MOCVD-coated tools was compared with that of tools coated using the industry-standard CVD process.Three multilayer cemented carbide cutting tool inserts, viz., TiN/TiC/WC, CVD-coated Al2O3 on TiN/TiC/WC, and MOCVD-coated Al2O3 on TiN/TiC/WC, were compared in the dry turning of mild steel. Turning tests were conducted for cutting speeds ranging from 14 to 47 m/min, for a depth of cut from 0.25 to 1 mm, at the constant feed rate of 0.2 mm/min. The axial, tangential, and radial forces were measured using a lathe tool dynamometer for different cutting parameters, and the machined work pieces were tested for surface roughness. The results indicate that, in most of the cases examined, the MOCVD-coated inserts produced a smoother surface finish, while requiring lower cutting forces, indicating that MOCVD produces the best-performing insert, followed by the CVD-coated one. The superior performance of MOCVD-alumina is attributed to the co-deposition of carbon with the oxide, due to the very nature of the precursor used, leading to enhanced mechanical properties for cutting applications in harsh environment.

Lubricity of an oil in water emulsion in metal cutting: The effect of hydrophilic/lypophilic balance of emulsifiers

A steel disc is cut using a single point tool. The coefficient of friction of the nascent cut surface is measured by a spherical steel pin situated in close proximity of the point of cutting. The tool, disc and the friction pin are immersed in an oil in water emulsion bath during the experiment. The purpose of the experiments conducted here is to record the effect of hydrophilic/lypophilic balance (HLB) of the emulsifier on the lubricity experienced in the cutting operation. The more lypophilic emulsifiers were found to give greater lubricity than what is recorded when the emulsifier is more hydrophilic. XPS and FTIR spectroscopy are used to explore the tribofilm generated on the nascent cut surface to indicate a possible rationale for the effect. (C) 2011 Elsevier B.V. All rights reserved.