Spray drift of pesticides arising from aerial application in cotton

This paper presents results from field studies carried out during the 1993-1998 Australian cotton (Gossypium hirsutum L.) seasons to monitor off-target droplet movement of endosulfan (6,7,8,9,10,10-hexachloro-1,5,5a,6,9,9a-hexahydro-6,9-methano-2,4,3-benzodioxathiepin 3-oxide) insecticide applied to a commercial cotton crop. Averaged over a wide range of conditions, off-target deposition 500 m downwind of the field boundary was approximately 2% of the field-applied rate with oil-based applications and 1% with water-based applications. Mean airborne drift values recorded 100 m downwind of a single flight line were a third as much with water-based application compared with oil-based application. Calculations using a Gaussian diffusion model and the U.S. Spray Drift Task Force AgDRIFT model produced downwind drift profiles that compared favorably with experimental data. Both models and data indicate that by adopting large droplet placement (LDP) application methods and incorporating crop buffer distances, spray drift can be effectively managed.

Augmentation of the assassin bug Pristhesancus plagipennis (Walker) (Hemiptera : Reduviidae) as a biological control agent for Helicoverpa spp. in cotton

Third-instar nymphs of the Australian assassin bug, Pristhesancus plagipennis (Walker), were released into cotton plots at two release densities and two crop growth stages to test their biological control potential. Release rates of 2 and 5 nymphs per metre row resulted in field populations of 0.51 and 1.38 nymphs per metre row, respectively, indicating that over 70% of nymphs died or emigrated within two weeks of release. Effective release rates of 1.38 nymphs per metre row reduced the number of Helicoverpa spp. larvae in the plots for a 7-week period. Crop yields were significantly greater in the plots to which P. plagipennis nymphs were released, with the effective release rate of 1.38 nymphs per metre row providing equivalent yields as insecticide treated plots. The data suggest that P. plagipennis has the capacity to reduce Helicoverpa spp. larvae densities in cotton crops when augmented through inundative release.

Factors affecting the establishment and dispersal of nymphs of Pristhesancus plagipennis Walker (Hemiptera : Reduviidae) when released onto soybean, cotton and sunflower crops

A problem with augmenting predatory bugs through mass release is the logistical difficulty of delivering nymphs onto the foliage of field crops. In this paper we examine postrelease establishment and dispersal of the nymphs of the predatory bug Pristhesancus plagipennis on soybean, cotton and sunflower in an effort to devise an appropriate strategy for field release. The effects of predator stadia and release rates on field establishment and within-crop-canopy dispersal after hand release were recorded in soybean, cotton and sunflower. Field establishment improved with the release of more-developed nymphs, with third instars providing the most appropriate compromise between field hardiness and rearing cost. Increased nymphal density at the point of release had little effect on nymphal dispersal throughout the crop canopy. The patterns of nymphal dispersal observed on the three crops suggest that crop-canopy architecture may have an effect on the ability of nymphs to spread out postrelease, as nymphs dispersed poorly in cotton and sunflower compared to soybean. To overcome poor dispersal of nymphs after release, a mechanical release method, where nymphs were mixed with vermiculite and delivered onto a target crop through a spinning disk fertiliser spreader, was tested, and provided similar nymph establishment rates and dispersal patterns as releasing nymphs individually by hand. The implications of nymph dispersal and field hardiness in regard to inundative field release techniques are discussed.

Linking physiological and architectural models of cotton

Despite the strong influence of plant architecture on crop yield, most crop models either ignore it or deal with it in a very rudimentary way. This paper demonstrates the feasibility of linking a model that simulates the morphogenesis and resultant architecture of individual cotton plants with a crop model that simulates the effects of environmental factors on critical physiological processes and resulting yield in cotton. First the varietal parameters of the models were made concordant. Then routines were developed to allocate the flower buds produced each day by the crop model amongst the potential positions generated by the architectural model. This allocation is done according to a set of heuristic rules. The final weight of individual bolls and the shedding of buds and fruit caused by water, N, and C stresses are processed in a similar manner. Observations of the positions of harvestable fruits, both within and between plants, made under a variety of agronomic conditions that had resulted in a broad range of plant architectures were compared to those predicted by the model with the same environmental inputs. As illustrated by comparisons of plant maps, the linked models performed reasonably well, though performance of the fruiting point allocation and shedding algorithms could probably be improved by further analysis of the spatial relationships of retained fruit. (C) 2002 Elsevier Science Ltd. All rights reserved.

Termo de coopera????o para a constru????o do marco anal??tico de avalia????o do projeto Cotton 4

O termo de coopera????o assinado entre a Escola Nacional de Administra????o P??blica (ENAP) e a Ag??ncia Brasileira de Coopera????o (ABC) tem como objetivo elaborar termo de refer??ncia, o qual especificar?? o perfil de um avaliador externo a ser posteriormente contratado para avaliar o projeto ???Apoio ao Desenvolvimento do Setor Algodoeiro dos Pa??ses do Cotton-4???. Esse projeto busca aumentar a produtividade, gerar diversidade gen??tica e aprimorar a qualidade do algod??o cultivado em Benin, Burkina Faso, Chade e Mali, de forma a contribuir para o desenvolvimento e o fortalecimento econ??mico

Nota informativa ACI/2014/001: constru????o de um marco anal??tico de avalia????o do projeto de coopera????o t??cnica internacional ???apoio ao desenvolvimento do setor algodoeiro do Cotton-4??? - ENAP/ABC

O texto possui quatro partes. A parte 1, Antecedentes, traz um hist??rico dos trabalhos conjuntos entre ENAP e ABC que justicam a solicita????o de apoio da ENAP para os desenvolvimentos sobre o projeto Cotton-4; a parte 2, A demanda da ABC a ENAP, contextualiza o projeto Cotton 4 e detalha a solicita????o original da ABC; a parte 3, Oportunidades para a ENAP, exp??e como a proposta foi complementada para potencializar outros trabalhos em curso da Escola. Finalmente, a parte 4, Implementa????o de a????es e seus principais resultados, resume os prop??sitos e a estrat??gia de execu????o do termo de coopera????o firmado entre ENAP e ABC

Herbicidal activity of volatiles from coriander, winter savory, cotton lavender, and thyme isolated by hydrodistillation and supercritical fluid extraction

The volatiles from Coriandrum sativum L., Satureja montana L., Santolina chamaecyparissus L., and Thymus vulgaris L. were isolated by hydrodistillation (essential oil) and supercritical fluid extraction (volatile oil). Their effect on seed germination and root and shoot growth of the surviving seedlings of four crops (Zea mays L., Triticum durum L., Pisum sativum L., and Lactuca sativa L.) and two weeds (Portulaca oleracea L. and Vicia sativa L.) was investigated and compared with those of two synthetic herbicides, Agrocide and Prowl. The volatile oils of thyme and cotton lavender seemed to be promising alternatives to the synthetic herbicides because they were the least injurious to the crop species. The essential oil of winter savory, on the other hand, affected both crop and weeds and can be appropriate for uncultivated fields.

Fracture toughness determination of adhesive and co-cured joints in natural fibre composites

Adhesive bonding has become more efficient in the last few decades due to the adhesives developments, granting higher strength and ductility. On the other hand, natural fibre composites have recently gained interest due to the low cost and density. It is therefore essential to predict the fracture behavior of joints between these materials, to assess the feasibility of joining or repairing with adhesives. In this work, the tensile fracture toughness (Gc n) of adhesive joints between natural fibre composites is studied, by bonding with a ductile adhesive and co-curing. Conventional methods to obtain Gc n are used for the co-cured specimens, while for the adhesive within the bonded joint, the J-integral is considered. For the J-integral calculation, an optical measurement method is developed for the evaluation of the crack tip opening and adherends rotation at the crack tip during the test, supported by a Matlab sub-routine for the automated extraction of these quantities. As output of this work, an optical method that allows an easier and quicker extraction of the parameters to obtain Gc n than the available methods is proposed (by the J-integral technique), and the fracture behaviour in tension of bonded and co-cured joints in jute-reinforced natural fibre composites is also provided for the subsequent strength prediction. Additionally, for the adhesively- bonded joints, the tensile cohesive law of the adhesive is derived by the direct method.

Sustainable waste recycling solution for the glass fibre reinforced polymer composite materials industry

In this paper the adequacy and the benefit of incorporating glass fibre reinforced polymer (GFRP) waste materials into polyester based mortars, as sand aggregates and filler replacements, are assessed. Different weight contents of mechanically recycled GFRP wastes with two particle size grades are included in the formulation of new materials. In all formulations, a polyester resin matrix was modified with a silane coupling agent in order to improve binder-aggregates interfaces. The added value of the recycling solution was assessed by means of both flexural and compressive strengths of GFRP admixed mortars with regard to those of the unmodified polymer mortars. Planning of experiments and data treatment were performed by means of full factorial design and through appropriate statistical tools based on analyses of variance (ANOVA). Results show that the partial replacement of sand aggregates by either type of GFRP recyclates improves the mechanical performance of resultant polymer mortars. In the case of trial formulations modified with the coarser waste mix, the best results are achieved with 8% waste weight content, while for fine waste based polymer mortars, 4% in weight of waste content leads to the higher increases on mechanical strengths. This study clearly identifies a promising waste management solution for GFRP waste materials by developing a cost-effective end-use application for the recyclates, thus contributing to a more sustainable fibre-reinforced polymer composites industry.

Processing of continuous fibre reinforced thermoplastics

Towpregs based on different fibres and thermoplastic matrices were processed for highly demanding and more commercial applications by different composite processing technologies. In the technologies used, compression moulding and pultrusion, the final composite pr ocessing parameters were studied in order to obtain composites with adequate properties at industrial compatible production rates. The produced towpregs were tested to verify its polymer content and degree of impregnation. The obtained results have shown t hat the coating line enabled to produce, with efficiency and industrial scale speed rates, thermoplastic matrix towpregs that may be used to manufacture composites for advanced and larger volume commercial markets.

Drilling of fibre reinforced plastic laminates

The use of fibre reinforced plastics – FRP’s – in structures is under a considerable increase. Advantages of their use are related with their low weight, high strength and stiffness. The improvement of the dynamic characteristics has been profitable for aeronautics, automobile, railway, naval and sporting goods industries. Drilling is a widely used machining technique as it is needed to assemble parts in a structure. This is a unique machining process, characterized by the existence of two different mechanisms: extrusion by the drill chisel edge and cutting by the rotating cutting lips. Drilling raises particular problems that can reduce mechanical and fatigue strength of the parts. In this work, quasi-isotropic hybrid laminates with 25% of carbon fibre reinforced plies and 4 mm thickness are produced, tested and drilled. Three different drill geometries are compared. Results considered are the interlaminar fracture toughness in Mode I – GIc –, thrust force during drilling and delamination extent after drilling. A bearing test is performed to evaluate tool influence on the load carrying capacity of the plate. Results consider the influence of drill geometry on delamination. A correlation linking plate damage to bearing test results is presented.

Delamination analysis of carbon fibre reinforced laminates: evaluation of a special step drill

Drilling of carbon fibre/epoxy laminates is usually carried out using standard drills. However, it is necessary to adapt the processes and/or tooling as the risk of delamination, or other damages, is high. These problems can affect mechanical properties of produced parts, therefore, lower reliability. In this paper, four different drills – three commercial and a special step (prototype) – are compared in terms of thrust force during drilling and delamination. In order to evaluate damage, enhanced radiography is applied. The resulting images were then computational processed using a previously developed image processing and analysis platform. Results show that the prototype drill had encouraging results in terms of maximum thrust force and delamination reduction. Furthermore, it is possible to state that a correct choice of drill geometry, particularly the use of a pilot hole, a conservative cutting speed – 53 m/min – and a low feed rate – 0.025 mm/rev – can help to prevent delamination.

Evaluation of tools and cutting conditions on carbon fibre reinforced laminates

The distinctive characteristics of carbon fibre reinforced plastics, like low weight or high specific strength, had broadened their use to new fields. Due to the need of assembly to structures, machining operations like drilling are frequent. In result of composites inhomogeneity, this operation can lead to different damages that reduce mechanical strength of the parts in the connection area. From these damages, delamination is the most severe. A proper choice of tool and cutting parameters can reduce delamination substantially. In this work the results obtained with five different tool geometries are compared. Conclusions show that the choice of an adequate drill can reduce thrust forces, thus delamination damage.