Mechanical, electrical and electro-mechanical properties of thermoplastic elastomer styrene–butadiene–styrene/multiwall carbon nanotubes composites

Composites of styrene–butadiene–styrene (SBS) block copolymer with multiwall carbon nanotubes were processed by solution casting to investigate the influence of filler content, the different ratios of styrene/butadiene in the copolymer and the architecture of the SBS matrix on the electrical, mechanical and electro-mechanical properties of the composites. It was found that filler content and elastomer matrix architecture influence the percolation threshold and consequently the overall composite electrical conductivity. The mechanical properties are mainly affected by the styrene and filler content. Hopping between nearest fillers is proposed as the main mechanism for the composite conduction. The variation of the electrical resistivity is linear with the deformation. This fact, together with the gauge factor values in the range of 2–18, results in appropriate composites to be used as (large) deformation sensors.

Velocidade da corrosão do aço em argamassas cimentícias modificadas com polímeros

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química

Synthesis, characterization and reactivity of new cobalt, palladium and nickel complexes bearing α-diimines and P, O ligands

This work describes the synthesis and characterization of a series of new α-diimine and P,O, β-keto and acetamide phosphines ligands, and their complexation to Ni(II), Co(II),Co(III) and Pd(II) to obtain a series of new compounds aiming to study their structural characteristics and to test their catalytic activity. All the compounds synthesized were characterized by the usual spectroscopic and spectrometric techniques: Elemental Analysis, MALDI-TOF-MS spectrometry, IR, UV-vis, 1H, 13C and 31P NMR spectroscopies. Some of the paramagnetic compounds were also characterized by EPR. For the majority of the compounds it was possible to solve their solid state structure by single crystal X-ray diffraction. Tests for olefin polymerization were performed in order to determine the catalytic activity of the Co(II) complexes. Chapter I presents a brief introduction to homogenous catalysis, highlighting the reactions catalyzed by the type of compounds described in this thesis, namely olefin polymerization and oligomerization and reactions catalyzed by the complexes bearing α-diimines and P,O type ligands. Chapter II is dedicated to the description of the synthesis of new α-diimines cobalt (II) complexes, of general formula [CoX2(α-diimine)], where X = Cl or I and the α-diimines are bis(aryl)acenaphthenequinonediimine) (Ar-BIAN) and 1,4-diaryl-2,3-dimethyl-1,4-diaza-1,3-butadiene (Ar-DAB). Structures solved by single crystal X-ray diffraction were obtained for all the described complexes. For some of the compounds, X-band EPR measurements were performed on polycrystalline samples, showing a high-spin Co(II) (S = 3/2) ion, in a distorted axial environment. EPR single crystal experiments on two of the compounds allowed us to determine the g tensor orientation in the molecular structure. In Chapter III we continue with the synthesis and characterization of more cobalt (II)complexes bearing α-diimines of general formula [CoX2(α-diimine)], with X = Cl or I and α-diimines are bis(aryl)acenaphthenequinonediimine) (Ar-BIAN) and 1,4-diaryl-2,3-dimethyl- 1,4-diaza-1,3-butadiene (Ar-DAB). The structures of three of the new compounds synthesized were determined by single crystal X-ray diffraction. A NMR paramagnetic characterization of all the compounds described is presented. Ethylene polymerization tests were done to determine the catalytic activity of several of the Co(II) complexes described in Chapter II and III and their results are shown. In Chapter IV a new rigid bidentate ligand, bis(1-naphthylimino)acenaphthene, and its complexes with Zn(II) and Pd(II), were synthesized. Both the ligand and its complexes show syn and anti isomers. Structures of the ligand and the anti isomer of the Pd(II) complex were solved by single crystal X-ray diffraction. All the compounds were characterized by elemental analysis, MALDI-TOF-MS spectrometry, and by IR, UV-vis, 1H, 13C, 1H-1H COSY, 1H-13C HSQC, 1H-13C HSQC-TOCSY and 1H-1H NOESY NMR when necessary. DFT studies showed that both conformers of [PdCl2(BIAN)] are isoenergetics and can be obtain experimentally. However, we can predict that the isomerization process is not available in square-planar complex, but is possible for the free ligand. The molecular geometry is very similar in both isomers, and only different orientations for naphthyl groups can be expected. Chapter V describes the synthesis of new P, O type ligands, β-keto phosphine, R2PCH2C(O)Ph, and acetamide phosphine R2PNHC(O)Me, as well as a series of new cobalt(III) complexes namely [(η5-C5H5)CoI2{Ph2PCH2C(O)Ph}], and [(η5- C5H5)CoI2{Ph2PNHC(O)Me}]. Treating these Co(III) compounds with an excess of Et3N, resulted in complexes η2-phosphinoenolate [(η5-C5H5)CoI{Ph2PCH…C(…O)Ph}] and η2- acetamide phosphine [(η5-C5H5)CoI{Ph2PN…C(…O)Me}]. Nickel (II) complexes were also obtained: cis-[Ni(Ph2PN…C(…O)Me)2] and cis-[Ni((i-Pr)2PN…C(…O)Me)2]. Their geometry and isomerism were discussed. Seven structures of the compounds described in this chapter were determined by single crystal X-ray diffraction. The general conclusions of this work can be found in Chapter VI.

Uma abordagem à incorporação de lenhinosulfonatos e materiais reciclados em misturas de SBR para produção sustentável de solas

Mestrado em Engenharia Química - Ramo Otimização Energética na Indústria Química

Effect of incorporating different waste materials in bitumen

The increasing environmental concern about waste materials and the necessity of improving the performance of asphalt mixtures prompted the study of incorporating different waste materials in conventional bitumen. The reuse of waste materials can present benefits at an environmental and economic level, and some wastes can be used to improve the pavement performance. Thus, the purpose of this study is to evaluate the incorporation of different waste materials in bitumen, namely waste motor oil and different polymers. In order to accomplish this goal, 10% of waste motor oil and 5% of polymers (high density polyethylene, crumb rubber and styrene-butadiene-styrene) were added to a conventional bitumen and the resulting modified bitumens were characterized through basic and rheological tests. From this work, it can be concluded that the incorporation of different waste materials improve some important properties of the conventional bitumen. Such improvements might indicate a good behaviour at medium/high temperatures and an increase of fatigue and rutting resistance. Therefore, these modified bitumens with waste materials can contribute to a sustainable development of road paving industry due to their performance and environmental advantages.

Grafting of adipic anhydride to carbon nanotubes through a Diels-Alder cycloaddition/oxidation cascade reaction

Accepted Manuscript

Synthesis of iminosugars through diastereo/enantioselective diels-alder cycloaddition

Tese de Doutoramento em Ciências (Especialidade em Química)

Síntese de tetrahidroquinolinas a partir da D-eritrose

Dissertação de mestrado em Química Medicinal

Full Exploration of the Diels–Alder Cycloaddition on Metallofullerenes M3N@C80 (M=Sc, Lu, Gd): The D5h versus Ih Isomer and the Influence of the Metal Cluster

In this work a detailed investigation of the exohedral reactivity of the most important and abundant endohedral metallofullerene (EMF) is provided, that is, Sc3N@Ih-C80 and its D5h counterpart Sc3N@D5h-C80, and the (bio)chemically relevant lutetium- and gadolinium-based M3N@Ih/D5h-C80 EMFs (M=Sc, Lu, Gd). In particular, we analyze the thermodynamics and kinetics of the Diels–Alder cycloaddition of s-cis-1,3-butadiene on all the different bonds of the Ih-C80 and D5h-C80 cages and their endohedral derivatives. First, we discuss the thermodynamic and kinetic aspects of the cycloaddition reaction on the hollow fullerenes and the two isomers of Sc3N@C80. Afterwards, the effect of the nature of the metal nitride is analyzed in detail. In general, our BP86/TZP//BP86/DZP calculations indicate that [5,6] bonds are more reactive than [6,6] bonds for the two isomers. The [5,6] bond D5h-b, which is the most similar to the unique [5,6] bond type in the icosahedral cage, Ih-a, is the most reactive bond in M3N@D5h-C80 regardless of M. Sc3N@C80 and Lu3N@C80 give similar results; the regioselectivity is, however, significantly reduced for the larger and more electropositive M=Gd, as previously found in similar metallofullerenes. Calculations also show that the D5h isomer is more reactive from the kinetic point of view than the Ih one in all cases which is in good agreement with experiments

Beneficial Effects of Selected Additives on Asphalt Cement Mixes, HR-278, 1987

Effects of polyolefins, neoprene, styrene-butadiene-styrene (SBS) block copolymers, styrene-butadiene rubber (SBR) latex, and hydrated lime on two asphalt cements were evaluated. Physical and chemical tests were performed on a total of 16 binder blends. Asphalt concrete mixes were prepared and tested with these modified binders and two aggregates (crushed limestone and gravel), each at three asphalt content levels. Properties evaluated on the modified binders (original and thin-film oven aged) included: viscosity at 25 deg C, 60 deg C and 135 deg C with capillary tube and cone-plate viscometer, penetration at 5 deg C and 25 deg C, softening point, force ductility, and elastic recovery at 10 deg C, dropping ball test, tensile strength, and toughness and tenacity tests at 25 deg C. From these the penetration index, the viscosity-temperature susceptibility, the penetration-viscosity number, the critical low-temperature, long loading-time stiffness, and the cracking temperature were calculated. In addition, the binders were studied with x-ray diffraction, reflected fluorescence microscopy, and high-performance liquid chromatography techniques. Engineering properties evaluated on the 72 asphalt concrete mixes containing additives included: Marshall stability and flow, Marshall stiffness, voids properties, resilient modulus, indirect tensile strength, permanent deformation (creep), and effects of moisture by vacuum-saturation and Lottman treatments. Pavement sections of varied asphalt concrete thicknesses and containing different additives were compared to control mixes in terms of structural responses and pavement lives for different subgrades. Although all of the additives tested improved at least one aspect of the binder/mixture properties, no additive was found to improve all the relevant binder/mixture properties at the same time. On the basis of overall considerations, the optimum beneficial effects can be expected when the additives are used in conjunction with softer grade asphalts.

Development of Bio-Based Polymers for Use in Asphalt, TR-639, 2014

Asphalt binder is typically modified with poly type (styrene-butadiene-styrene or SBS) polymers to improve its rheological properties and performance grade. The elastic and principal component of SBS polymers is butadiene. For the last decade, butadiene prices have fluctuated and significantly increased, leading state highway agencies to search for economically viable alternatives to butadiene based materials. This project reports the recent advances in polymerization techniques that have enabled the synthesis of elastomeric, thermoplastic, block-copolymers (BCPs) comprised of styrene and soybean oil, where the “B” block in SBS polymers is replaced with polymerized triglycerides derived from soybean oil. These new breeds of biopolymers have elastomeric properties comparable to well-established butadiene-based styrenic BCPs. In this report, two types of biopolymer formulations are evaluated for their ability to modify asphalt binder. Laboratory blends of asphalt modified with the biopolymers are tested for their rheological properties and performance grade. Blends of asphalt modified with the biopolymers are compared to blends of asphalt modified with two commonly used commercial polymers. The viscoelastic properties of the blends show that biopolymers improve the performance grade of the asphalt to a similar and even greater extent as the commercial SBS polymers. Results shown in this report indicate there is an excellent potential for the future of these biopolymers as economically and environmentally favorable alternatives to their petrochemically-derived analogs.

Toxicity assessment of refill liquids for electronic cigarettes.

We analyzed 42 models from 14 brands of refill liquids for e-cigarettes for the presence of micro-organisms, diethylene glycol, ethylene glycol, hydrocarbons, ethanol, aldehydes, tobacco-specific nitrosamines, and solvents. All the liquids under scrutiny complied with norms for the absence of yeast, mold, aerobic microbes, Staphylococcus aureus, and Pseudomonas aeruginosa. Diethylene glycol, ethylene glycol and ethanol were detected, but remained within limits authorized for food and pharmaceutical products. Terpenic compounds and aldehydes were found in the products, in particular formaldehyde and acrolein. No sample contained nitrosamines at levels above the limit of detection (1 μg/g). Residual solvents such as 1,3-butadiene, cyclohexane and acetone, to name a few, were found in some products. None of the products under scrutiny were totally exempt of potentially toxic compounds. However, for products other than nicotine, the oral acute toxicity of the e-liquids tested seems to be of minor concern. However, a minority of liquids, especially those with flavorings, showed particularly high ranges of chemicals, causing concerns about their potential toxicity in case of chronic oral exposure.

SB-lateksitehtaan päästöjen minimointi

Diplomityön tavoitteena oli löytää soveltuvimmat parhaaseen käytettävissä olevaan tekniikkaan perustuvat menetelmät SB-lateksitehtaan päästöjen käsittelemiseksi. Kirjallisuuslähteinä käytettiin Euroopan komission julkaisemia toimialakohtaisia BAT-julkaisuja. Lisäksi hyödynnettiin kemianteollisuudessa jo käytössä olevien menetelmien kokemusperäistä tietoa. Kokeellinen osan pohjaksi kartoitettiin merkittävät päästölähteet: kiinteät, nestemäiset ja kaasumaiset päästöt. Päästömittaukset olivat kvantitatiivisia, mutta mittauksissa kerättiin myös kvalitatiivista tietoa. Kirjallisen ja kokemusperäisen tiedon sekä päästöjen mittaustulosten perusteella valittiin soveltuvimmat päästöjenkäsittelyvaihtoehdot. Kiinteiden päästöjen määrään vaikuttaa eniten lateksin suodatusmenetelmän valinta. Nestemäisten päästöjen uudelleenkäyttö on tehokkain tapa minimoida päästöjä. Tehokkain tapa käsitellä orgaanisia jätevesiä on kolonnistrippaus. Lateksipitoisille jätevesille soveltuvin menetelmä on membraanitekniikka. Kaasuseospäästöille soveltuvin käsittelymenetelmä on terminen kammiopoltto. Yhden kemikaalin kaasupäästöjen käsittelyssä menetelmät perustuvat kondensointiin, paikallisiin suodattimiin ja kaasujen takaisinkierrätykseen riippuen kemikaalin ominaisuuksista.

STYREENI-BUTADIEENILATEKSIN VALMISTUS EMULSIOPOLYMEROIN-NILLA JA LATEKSIN VISKOSITEETTIIN VAIKUTTAVAT TEKIJÄT.

Työn tavoitteina oli kirjallisuusosassa selvittää emulsiopolymeroinnin perusperiaatteet ja lateksien viskositeettiin vaikuttavat tekijät. Kokeellisessa osassa selvitettiin eräiden kaupallisten lateksien viskositeettiin vaikuttavia tekijöitä. Tutkittujen kaupallisten lateksien viskositeettien riippuvuudelle kuiva-ainepitoisuudesta saatiin tulokset, jotka ovat melko hyvin yhtäpitäviä kirjallisuudesta saatujen tulosten kanssa. Tutkitut lateksit erosivat lähinnä maksimaalisen polymeeripartikkelin tilavuusosuuden kohdalla kirjallisuudesta saaduista arvoista. Tämän todettiin johtuvan sähköisen kaksoiskerroksen ja partikkelin pintaan kiinnittyneiden ryhmien vaikutuksesta. Tämä tulos varmentui elektrolyyttipitoisuuden vaikutusta selvitettäessä. Elektrolyyttilisäys laski lateksien viskositeetteja ja pienensi lateksien välisiä viskositeettieroja. Lateksin pH:n nostolla oli selvästi viskositeettia kasvattava vaikutus. Tämä johtuu osaltaan myös sähköisen kaksoiskerroksen kasvamisesta happoryhmien ionisoituessa. Latekseja toisiinsa verrattaessa havaittiin selkeästi karboksyylihapon ja initiaattorista peräisin olevien happoryhmien määrän vaikutus lateksin viskositeetin muutokselle. Paljon karboksyylihappoa ja initiaattoria sisältävien lateksien viskositeetti muuttui selvästi voimakkaammin pH:n muuttuessa. Latekseissa havaittiin myös ero heikkojen karboksyylihapporyhmien ja vahvojen initiaattorista peräisin olevien happoryhmien ionisoitumisen välillä. Vahvat happoryhmät ionisoituivat matalammassa pH:ssa kuin vahvat ja nostavat näin myös viskositeettia matalammassa pH:ssa kuin karboksyylihapporyhmät. Anionisen emulgaattorin lisäyksellä ei havaittu olevan kovinkaan suurta vaikutusta viskositeettiin. Partikkelikoon vaikutusta voitiin tutkia ainoastaan prosessista saadun mittausaineiston avulla. Partikkelikoon vaikutukset peittyivät suurelta osin muiden tekijöiden alle. Ainoastaan yhdelle lateksityypille saatiin selkeä riippuvuus partikkelikoon ja viskositeetin välille. Riippuvuus noudattaa kirjallisuudesta saatuja tietoja eli partikkelikoon kasvaessa viskositeetti laskee. Myös lateksin viskositeetin riippuvuus käytetystä leikkaus-nopeudesta noudattaa hyvin kirjallisuudesta saatuja tuloksia. Lateksin viskositeetti laskee leikkausnopeuden kasvaessa.

Síntese de catalisadores Ziegler-Natta: algumas rotas e suas dificuldades

The Ziegler-Natta catalyst and the polymerization thereof are systems which require careful handling and special treatment of chemicals. In spite of the use of inert atmosphere and dry chemicals, some Ziegler-Natta systems may present low activities or even may deactivate because of unsuitable handling. Some features of the TiCl3 synthesis and its characterization when related to the presence of impurities are described. Evidences of poor handling of chemicals and/or laboratory devices while in synthesis of the catalyst are emphasized. The problems arising from butadiene polymerization and some relevant details in propylene polymerization are also presented with teaching objectives.