Paper re-use: Toner-print removal by laser ablation

This article explores the possibility of using a laser to remove toner-print from office paper. Removal of print would allow paper to be re-used instead of being recycled or disposed into a landfill. This might reduce climate change gas emissions per tonne of office paper by between 45% and 95%. Although there is little previous research on the area, a number of related articles on paper conservation methods using laser radiation can be found in literature. Different authors have studied the effects of laser energy on blank paper and its application for cleaning soiled paper. However, this study examines toner-print removal from paper by laser ablation. In this article a laser in the visible range is applied to a single toner-paper combination with a range of energy fluences. Results are evaluated by means of colour measurements under the L*a*b* colour space and SEM images. Analysis of the samples reveals that there are parameters under which it is possible to remove toner from paper without causing significant discolouration or damage to the substrate. This means that it is technically possible to remove toner-print for paper re-use.

Notes on the induced maturation and spawning in four-month-old Penaeus monodon Fabricius by eyestalk ablation

The ablation technique consisted of making an incision across the eyeball to allow free flow of fluids while holding the prawn under water, squeezing the eyeball contents outwards, and pinching hard the eyestalk tissue. The cut area heals completely in about a week; no application of antibiotics is necessary. Spent spawners were tagged with thin brass rings (Rodriguez, 1976) around the unablated eyestalk for a separate experiment on rematuration. Two spawning yielding approximately 277,000 eggs were obtained three weeks after ablation, followed four days later by two more spawnings with 160,000 eggs; all four spawners weighed more than 100 g. With a hatching rate of 98% and 78% for the first and second batch, respectively, the spawnings produced viable nauplii. Water temperatures as low as 23 degree C due to a delayed cold spell in March depressed molting; weakened larvae had to be discharged at the mysis stage. Although ovarian development continued, no further spawnings were obtained due mainly to the onset of bacterial and fungal disease. Infection is initiated in injured portions of the exoskeleton, sometimes penetrating right through the muscles to the ovarian tissues. The non-flowthrough conditions and mussel meat feeding led to fouling of the culture water resulting in consecutive mortalities caused by disease. Female P.monodon held in maturation pens were ablated at the age of 15 months (Santiago, et al., 1976); they averaged only 16 g body weight after four months growth in ponds. In another experiment, pond-reared P.monodon females ranging from 50 to 80 g were ablated at approximately seven months (Aquacop, 1977). The present results show a minimum age of four months from postlarve that P.monodon is capable of ovarian development and spawning upon ablation. However, maturation is probably affected by size as well as age - the four-month old females weighed an average of 100 g in contrast to the smaller animals in the earlier experiments.

Fibre laser microvia drilling and ablation of Si with tuneable pulse shapes

The dramatic increase in hole quality on single crystalline silicon with an 1 μm fiber laser has been reported recently, it redefines the processing options for Si at that wavelength. This study investigated the effects of the MOPA based pulse tuning on the changes of the machined depth and the mass removal mechanism for the generation of microvia holes. Hole depths were measured and surface morphology studied using SEM and optical interferometric profilometry. The pulse peak power was found to strongly influence the material removal mechanism with fixed pulse duration. High peak powers (>1 kW) gave vaporization dominated ablation, left a limited re solidified molten layer and clean hole formation. The pulse duration was found to strongly influence the machined depth. Longer pulse durations generated deeper holes with constant peak power (>1 kW). In comparison with the DPSS UV laser, the IR fiber laser of longer pulse durations machined deeper holes and generated less resolidifed melt beyond the hole rim at high fluencies. The comparison suggests that some applications (microvia drilling) of the DPSS UV laser can be replaced with the more flexible, low cost IR fiber laser. © KSPE and Springer 2012.

Study on pulsed laser ablation and deposition of ZnO thin films by L-MBE

ZnO, as a wide-band gap semiconductor, has recently become a new research focus in the field of ultraviolet optoelectronic semiconductors. Laser molecular beam epitaxy (L-MBE) is quite useful for the unit cell layer-by-layer epitaxial growth of zinc oxide thin films from the sintered ceramic target. The ZnO ceramic target with high purity was ablated by KrF laser pulses in an ultra high vacuum to deposit ZnO thin film during the process of L-MBE. It is found that the deposition rate of ZnO thin film by L-MBE is much lower than that by conventional pulsed laser deposition (PLD). Based on the experimental phenomena in the ZnO thin film growth process and the thermal-controlling mechanism of the nanosecond (ns) pulsed laser ablation of ZnO ceramic target, the suggested effective ablating time during the pulse duration can explain the very low deposition rate of the ZnO film by L-MBE. The unique dynamic mechanism for growing ZnO thin film is analyzed. Both the high energy of the deposition species and the low growth rate of the film are really beneficial for the L-MBE growth of the ZnO thin film with high crystallinity at low temperature.

中能Abrasion-Ablation模型的核内核子密度分布修正

将具体的核内核子 (包括中子、质子 )密度分布引入到中能Abrasion -Ab lation模型中 ,用修正后的模型计算了 30MeV/u　 4 0 Ar +natAg反应中的弹核碎裂过程 .结果表明 ,在非常周边的碰撞中 ,修正后的模型计算的碎片截面与修正前的计算相比有明显的差别 ,反映了核密度边缘弥散的影响 .与实验结果的比较验证了中能弹核碎裂碎片能量相对于束流能量的降低是由摩擦作用引起的 .