Characterization and application of the solid waste generated in the production of calcium carbonate precipitate as a corrective for the soil acidity

The calcium carbonate industry generates solid waste products which, because of their high alkaline content (CaO, CaCO(3) and Ca (OH)(2)), have a substantial impact on the environment. The objectives of this study are to characterize and classify the solid waste products, which are generated during the hydration process of the calcium carbonate industry, according to ABNT`s NBR 10.000 series, and to determine the potential and efficiency of using these solid residues to correct soil acidity. Initially, the studied residue was submitted to gross mass, leaching, solubility, pH. X-ray Diffractometry, Inductive Coupled Plasma - Atomic Emission Spectrometry (ICP-AES), granularity and humidity analyses. The potential and efficiency of the residue for correcting soil acidity was determined by analysis of the quality attributes for soil correctives (PN, PRNT, Ca and Mg contents, granularity). Consequently, the results show that the studied residue may be used as a soil acidity corrective, considering that a typical corrective compound is recommended for each different type of soil. Additionally, the product must be further treated (dried and ground) to suit the specific requirements of the consumer market.

Laboratory evaluation of recycled construction and demolition waste for pavements

The wide production of construction and demolition waste and its illegal deposition are serious current problems in Brazil. This research proposes to evaluate the feasibility of using aggregate from recycled construction and demolition waste (RCDW) in pavement applications. A laboratory program was conducted by geotechnical characterization, bearing capacity and repeated load triaxial tests. The results show that the composition and the compactive effort influence on the physical characteristics of the RCDW aggregate. The compaction process has promoted a partial crushing and breakage of RCDW particles, changing the grain-size distribution and increasing the percentage of cubic grains. This physical change contributes to a better densification of the RCDW aggregate and consequently an improvement in bearing capacity, resilient modulus and resistance to permanent deformation. The results have shown that the RCDW aggregate may be utilized as coarse base and sub-base layer for low-volume roads. (C) 2010 Elsevier Ltd. All rights reserved.

Chemical-mineralogical characterization of C&D waste recycled aggregates from Sao Paulo, Brazil

This study presents a methodology for the characterization of construction and demolition (C&D) waste recycled aggregates based on a combination of analytical techniques (X-ray fluorescence (XRF), soluble ions, semi-quantitative X-ray diffraction (XRD), thermogravimetric analysis (TCA-DTG) and hydrochloric acid (HCl) selective dissolution). These combined analytical techniques allow for the estimation of the amount of cement paste, its most important hydrated and carbonated phases, as well as the amount of clay and micas. Details of the methodology are presented here and the results of three representative C&D samples taken from the Sao Paulo region in Brazil are discussed. Chemical compositions of mixed C&D aggregate samples have mostly been influenced by particle size rather than the visual classification of C&D into red or grey and geographical origin. The amount of measured soluble salts in C&D aggregates (0.15-25.4 mm) is lower than the usual limits for mortar and concrete production. The content of porous cement paste in the C&D aggregates is around 19.3% (w/w). However, this content is significantly lower than the 43% detected for the C&D powders (< 0.15 min). The clay content of the powders was also high, potentially resulting from soil intermixed with the C&D waste, as well as poorly burnt red ceramic. Since only about 50% of the measured CaO is combined with CO(2), the powders have potential use as raw materials for the cement industry. (C) 2008 Elsevier Ltd. All rights reserved.

Synthesis of Cyclic Guanidine Intermediates of Anatoxin-a(s) in Both Racemic and Enantiomerically Pure Forms

The alkyl chain of anatoxin-a(s) (cyclic guanidines), which can be used as an intermediate in the total synthesis of anatoxin-a(s), was synthesized in both racemic and enantiomerically pure forms. These enantiomerically pure cyclic compounds can be used as chiral inductors in some reactions. The two racemic routes disclosed herein have the advantages of high overall yield and mild reaction conditions. Both routes proceed through an intermediate 2,3-diaminoacid - an important synthetic scaffold - with good yields. Furthermore, the N,N-dimethyl-2(tosylimino)imidazolidine-4-carboxamide might be obtained from 2-(tosylimino)imidazolidine-4-carboxylic acid followed by selective reduction of the carbonyl functionality. All synthesized compounds were analyzed by mass spectrometry and (1)H NMR and (13)C NMR spectroscopy.

Monocyte-derived dendritic cells from patients with severe forms of chromoblastomycosis induce CD4(+) T cell activation in vitro

Dendritic cells (DCs) have been described as initiators and modulators of the immune response. Recently we have shown a predominant production of interleukin-10 cytokine, low levels of interferon-gamma and inefficient T cell proliferation in patients with severe forms of chromoblastomycosis. Chromoblastomycosis starts with subcutaneous inoculation of Fonsecaea pedrosoi into tissue where DCs are the first line of defence against this microorganism. In the present study, the interaction of F. pedrosoi and DCs obtained from patients with chromoblastomycosis was investigated. Our results showed that DCs from patients exhibited an increased expression of human leucocyte antigen D-related (HLA-DR) and co-stimulatory molecules. In the presence of conidia, the expression of HLA-DR and CD86 was up-regulated by DCs from patients and controls. Finally, we demonstrate the reversal of antigen-specific anergy and a T helper type 1 response mediated by DCs incubated with F. pedrosoi conidea.

Preparation and characterization of ethanol-treated silk fibroin dense membranes for biomaterials application using waste silk fibers as raw material

The possibility of producing valued devices from low cost natural resources is a subject of broad interest. The present study explores the preparation and characterization of silk fibroin dense membranes using waste silk fibers from textile processing. Morphology, crystallinity, thermal resistance and cytotoxicity of membranes as well as the changes on the secondary structure of silk fibroin were analyzed after undergoing treatment with ethanol. Membranes presented amorphous patterns as determined via X-ray diffraction. The secondary structure of silk fibroin on dense membranes was either random coil (silk I) or p-sheet (silk II), before and after ethanol treatment, respectively. The sterilized membranes presented no cytotoxicity to endothelial cells during in vitro assays. This fact stresses the material potential to be used in the fabrication of biomaterials, as coatings of cardiovascular devices and as membranes for wound dressing or drug delivery systems. (C) 2010 Elsevier Ltd. All rights reserved.

Standing wave bed forms at Plage de la Grande Roche, le Verdelet, Pléneuf-Val-André, Cote d’Armor (France)

Coastal Photograph by Hubert Chanson This photograph of standing wave bed forms was taken at very low tide. The tidal range was 10 m. The bed forms were located on the island of Le Verdelet, in a channel between Le Grande Jaune and Le Verdelet. It is likely that these standing wave bed forms were formed during transcritical shallow water flows at the end of ebb tide. The author’s watch is in the foreground for scale. (Coastal Photograph by Hubert Chanson, Division of Civil Engineering, the University of Queensland, Brisbane, Queensland 4072, Australia.)

Two dimensional computational fluid dynamic models for waste stabilisation ponds

Traditional waste stabilisation pond (WSP) models encounter problems predicting pond performance because they cannot account for the influence of pond features, such as inlet structure or pond geometry, on fluid hydrodynamics. In this study, two dimensional (2-D) computational fluid dynamics (CFD) models were compared to experimental residence time distributions (RTD) from literature. In one of the-three geometries simulated, the 2-D CFD model successfully predicted the experimental RTD. However, flow patterns in the other two geometries were not well described due to the difficulty of representing the three dimensional (3-D) experimental inlet in the 2-D CFD model, and the sensitivity of the model results to the assumptions used to characterise the inlet. Neither a velocity similarity nor geometric similarity approach to inlet representation in 2-D gave results correlating with experimental data. However. it was shown that 2-D CFD models were not affected by changes in values of model parameters which are difficult to predict, particularly the turbulent inlet conditions. This work suggests that 2-D CFD models cannot be used a priori to give an adequate description of the hydrodynamic patterns in WSP. (C) 1998 Elsevier Science Ltd. All rights reserved.

Cost-benefit analysis of alternative forms of hedgerow intercropping in the Philippine uplands

Considerable resources have been expended promoting hedgerow intercropping with shrub legumes to farmers in the Philippine uplands. Despite the resources committed to research and extension, persistent adoption by farmers has been limited to low cost versions of the technology including natural vegetation and grass strips. In this paper, cost-benefit analysis is used to compare the economic returns from traditional open-field maize farming with returns from intercropping maize between leguminous shrub hedgerows, natural vegetation strips and grass strips. An erosion/productivity model, Soil Changes Under Agroforestry, was used to predict the effect of erosion on maize yields. Key informant surveys with experienced maize farmers were used to derive production budgets for the alternative farming methods. The economic incentives revealed by the cost-benefit analysis help to explain the adoption of maize farming methods in the Philippine uplands. Open-field farming without hedgerows has been by far the most popular method of maize production, often with two or more fields cropped in rotation. There is little persistent adoption of hedgerow intercropping with shrub legumes because sustained maize yields are not realised rapidly enough to compensate farmers for establishment and maintenance costs. Natural vegetation and grass strips are more attractive to farmers because of lower establishment costs, and provide intermediate steps to adoption. Rural finance, commodity pricing and agrarian reform policies influence the incentives for maize farmers in the Philippine uplands to adopt and maintain hedgerow intercropping.

Familial forms broaden the horizons for primary aldosteronism

The identification of familial forms of primary aldosteronism (PAL) has led to its detection in relatives of affected patients not suspected previously of having PAL. Many ave normokalemic and some ave even normotensive. This broadens the spectrum of PAL, permitting the study of its evolution and of intervention with specific therapy when hypertension develops. The genetic basis of one form involves steroid biosynthetic enzymes and the other form predisposes to hyperplasia and benign neoplasia.

Selection of a strain of Aspergillus for the production of citric acid from pineapple waste in solid-state fermentation

Aspergillus foetidus ACR I 3996 (=FRR 3558) and three strains of Aspergillus niger ACM 4992 (=ATCC 9142), ACM 4993 (=ATCC 10577), ACM 4994 (=ATCC 12846) were compared for the production of citric acid from pineapple peel in solid-state fermentation. A. niger ACM 4992 produced the highest amount of citric acid, with a yield of 19.4 g of citric acid per 100 g of dry fermented pineapple waste under optimum conditions, representing a yield of 0.74 g citric acid/g sugar consumed. Optimal conditions were 65% (w/w) initial moisture content, 3% (v/w) methanol, 30 degrees C, an unadjusted initial pH of 3.4, a particle size of 2 mm and 5 ppm Fe2+. Citric acid production was best in flasks, with lower yields being obtained in tray and rotating drum bioreactors.

Structures of free and complexed forms of Escherichia coli xanthine-guanine phosphoribosyltransferase

Structures of free, substrate-bound and product-bound forms of Escherichia coli xanthine-guanine phosphoribosyltransferase (XGPRT) have been determined by X-ray crystallography. These are compared with the previously determined structure of magnesium and sulphate-bound XPRT. The structure of free XGPRT at 2.25 Angstrom resolution confirms the flexibility of residues in and around a mobile loop identified in other PRTases and shows that the cis-peptide conformation of Arg37 at the active site is maintained in the absence of bound ligands. The structures of XGPRT complexed with the purine base substrates guanine or xanthine in combination with cPRib-PP, an analog of the second substrate PRib-PP, have been solved to 2.0 Angstrom resolution. In these two structures the disordered phosphate-binding loop of uncomplexed XGPRT becomes ordered through interactions with the 5'-phosphate group of cPRib-PP. The cyclopentane ring of cPRib-PP has the C3 exo pucker conformation, stabilised by the cPRib-PP-bound Mg2+. The purine base specificity of XGPRT appears to be due to water-mediated interactions between the 2-exocyclic groups of guanine or xanthine and side-chains of Glu136 and Asp140, as well as the main-chain oxygen atom of Ile135. Asp92, together with Lys115, could help stabilise the N7-protonated tautomer of the incoming base and could act as a general base to remove the proton from N7 .when the nucleotide product is formed. The 2.6 Angstrom resolution structure of XGPRT complexed with product GMP is similar to the substrate-bound complexes. However, the ribose ring of GMP is rotated by similar to 24 degrees compared with the equivalent ring in cPRib-PP. This rotation results in the loss of all interactions between the ribosyl group and the enzyme in the product complex. (C) 1998 Academic Press.

Availability of two forms of dissolved nitrogen to the coral Pocillopora damicornis and its symbiotic zooxanthellae

The relative contribution of dissolved nitrogen (ammonium and dissolved free amino acids DFAAs) to the nitrogen budget of the reef-building coral Pocillopora damicornis was assessed for colonies growing on control and ammonium-enriched reefs at One Tree Island (southern Great Barrier Reef) during the ENCORE (Enrichment of Nutrient on Coral Reef; 1993 to 1996) project. P. damicornis acquired ammonium at rates of between 5.1 and 91.8 nmol N cm(-2) h(-1) which were not affected by nutrient treatment except in the case of one morph. In this case, uptake rates decreased from 80.5 to 42.8 nmol cm(-2) h(-1) (P < 0.05) on exposure to elevated ammonium over 12 mo. The presence or absence of light during measurement did not influence the uptake of ammonium ions. Nitrogen budgets revealed that the uptake of ammonium from concentrations of 0.11 to 0.13 mu M could completely satisfy the demand of growing P. damicornis for new nitrogen. P. damicornis also took up DFAAs at rates ranging from 4.9 to 9.8 nmol N cm(-2) h(-1). These rates were higher in the dark than in the light (9.0 vs 5.1 nmol m(-2) h(-1), P < 0.001). Uptake rates were highest for the amino acids serine, arginine and alanine, and lowest for tyrosine. DFAA concentrations within the ENCORE microatolls that received ammonium were undetectable, whereas they ranged up to 100 nM within the control microatolls. The contribution of DFAAs to the nitrogen budget of P. damicornis constituted only a small fraction of the nitrogen potentially contributed by ammonium under field conditions. Even at the highest field concentrations measured during this study, DFAAs could contribute only similar or equal to 11.3% of the nitrogen demand of P. damicornis. This contribution, however, may be an important source of nitrogen when other sources such as ammonium are scarce or during periods when high concentrations of DFAAs become sporadically available (e.g. cell breakage during fish-grazing).

Purification,characterization and crystallization in two crystal forms of bovine cyclophilin 40

The purification and crystallization of two different crystal forms of the two-domain protein bovine cyclophilin 40 is reported. Tetragonal crystals grown in methyl pentanediol belong to space group P4(2)22 with unit-cell parameters a = 94.5, c = 118.3 Angstrom. Long thin needles grown from PEG belong to space group C2 with unit-cell parameters a = 125.71, b = 47.3, c = 74.6 Angstrom, beta = 93.90 degrees. The N-terminal 170 amino acids have significant homology with the well characterized human cyclophilin A. The C-terminal domain is largely made up of three copies of the tetratricopeptide repeat motif thought to be involved in mediating protein-protein interactions. Cyclophilins are frequently found as domains in larger multidomain proteins. To date, only X-ray structures of single-domain cyclophilins have been reported, and this work provides the first example of the purification and crystallization of a larger protein containing a cyclophilin domain.