Control of Ship Roll Motion

The undesirable effects of roll motion of ships (rocking about the longitudinal axis) became noticeable in the mid-nineteenth century when significant changes were introduced to the design of ships as a result of sails being replaced by steam engines and the arrangement being changed from broad to narrow hulls. The combination of these changes led to lower transverse stability (lower restoring moment for a given angle of roll) with the consequence of larger roll motion. The increase in roll motion and its effect on cargo and human performance lead to the development several control devices that aimed at reducing and controlling roll motion. The control devices most commonly used today are fin stabilizers, rudder, anti-roll tanks, and gyrostabilizers. The use of different types of actuators for control of ship roll motion has been amply demonstrated for over 100 years. Performance, however, can still fall short of expectations because of difficulties associated with control system design, which have proven to be far from trivial due to fundamental performance limitations and large variations of the spectral characteristics of wave-induced roll motion. This short article provides an overview of the fundamentals of control design for ship roll motion reduction. The overview is limited to the most common control devices.

Vermicular graphite cast iron current state of the art

Vermicular graphite cast iron is a new addition to the family of cast irons. Various methods for producing vermicular graphite cast iron are briefly discussed in this paper. The mechanical and physical properties of cast irons with vermicular graphite have been found to be intermediate between those of gray and ductile irons. Other properties such as casting characteristics, scaling resistance, damping capacity and machinability have been compared with those of gray and ductile irons. Probable applications of vermicular graphite cast irons are suggested.

Gustaf III inför sina undersåtar : Konsten att härska och politikens kulturhistoria

The dissertation analyses the political culture of Sweden during the reign of King Gustav III (1771-1792). This period commonly referred to as the Gustavian era followed the so-called Age of Liberty ending half a century of strong parliamentary rule in Sweden. The question at the heart of this study engages with the practice of monarchical rule under Gustav III, its ideological origins and power-political objectives as well as its symbolic expression. The study thereby addresses the very nature of kingship. In concrete terms, why did Gustav III, his court, and his civil service vigorously pursue projects that contemporaneous political opponents and, in particular, subsequent historiography have variously pictured as irrelevant, superficial, or as products of pure vanity? The answer, the study argues, is to be found in patterns of political practice as developed and exercised by Gustav III and his administration, which formed a significant part of the political culture of Gustavian Sweden. The dissertation is divided into three parts. The first traces the use and development of royal graces chivalric orders, medals, titles, privileges, and other gifts issued by the king. The practice of royal reward is illustrated through two case studies: the 1772 coup d état that established Gustav III s rule, and the birth and baptism of the crown prince, Gustav Adolf, in 1778. The second part deals with the establishment of the Court of Appeal in Vasa in 1776. The formation of the Appeals Court was accompanied by a host of ceremonial, rhetorical, emblematic, and architectural features solidifying its importance as one of Gustav III s most symbolic administrative reform projects and hence portraying the king as an enlightened monarch par excellence. The third and final part of the thesis engages with war as a cultural phenomenon and focuses on the Russo-Swedish War of 1788-1790. In this study, the war against Russia is primarily seen as an arena for the king and other players to stage, create and re-create as well as articulate themselves through scenes and roles adhering to a particular cultural idiom. Its codes and symbolic forms, then, were communicated by means of theatre, literature, art, history, and classical mythology. The dissertation makes use of a host of sources: protocols, speeches, letters, diaries, newspapers, poetry, art, medals, architecture, inscriptions and registers. Traditional political source material and literary and art sources are studied as totalities, not as separate entities. Also it is argued that political and non-fictional sources cannot be understood properly without acknowledging the context of genre, literary conventions, and artistic modes. The study critically views the futile, but nonetheless almost habitual juxtaposition of the reality of images, ideas, and metaphors, and the reality of supposedly factual historical events. Significantly, the thesis presumes the symbolic dimension to be a constitutive element of reality, not its cooked up misrepresentation. This presumption is reflected in a discussion of the concept of role , which should not be anachronistically understood as roles in which the king cast himself at different times and in different situations. Neither Gustav III nor other European sovereigns of this period played the roles as rulers or majesties. Rather, they were monarchs both in their own eyes and in the eyes of their contemporaries as well as in all relations and contexts. Key words: Eighteenth-Century, Gustav III, Cultural History, Monarchs, Royal Graces, the Vasa Court of Appeal, the Russo-Swedish War 1788–1790.

Does a twin pregnancy have a greater impact on physical and emotional well-being than a singleton pregnancy?

A prospective, population-based study was conducted to assess the impact of twin pregnancy on a woman's physical and emotional well-being. It compared women's reports of their general health, experience of a range of specific symptoms, and emotional well-being during pregnancy using the Edinburgh Postnatal Depression Scale. The subjects were 147 women expecting twins and 11,061 women expecting a single child who completed questionnaires at both 20 and 32 weeks’gestation as part of the Avon Longitudinal Study of Pregnancy and Childhood. Results suggested that women expecting twins experienced poorer physical well-being but not poorer emotional well-being than those expecting a single child, even though a significant association between poor health and emotional well-being was found for the population as a whole. It was suggested that the transitory nature of a twin pregnancy, the “special’ status of a twin pregnancy, greater social support, and modified expectations about health may buffer the effects of poor physical health on emotional well-being in a twin pregnancy. The findings should alert those who care for women expecting twins to the greater physical stress these women may feel.

Twin roller quenching technique and preparation of glasses of high melting ionic solids

A rapid quenching technique with a quenching rate of roughly 106°C/sec has been developed to prepare glassy samples of ABO3 type materials. Glasses of potassium lithium niobate have been prepared by this technique. These glasses have been characterized by x-ray diffraction, electron diffraction and differential scanning calorimetry techniques to assess the quality of the obtained glasses.

Role of free volume in strain softening of as-cast and annealed bulk metallic glass

Plasticity in amorphous alloys is associated with strain softening, induced by the creation of additional free volume during deformation. In this paper, the role of free volume, which was a priori in the material, on work softening was investigated. For this, an as-cast Zr-based bulk metallic glass (BMG) was systematically annealed below its glass transition temperature, so as to reduce the free volume content. The bonded-interface indentation technique is used to generate extensively deformed and well defined plastic zones. Nanoindentation was utilized to estimate the hardness of the deformed as well as undeformed regions. The results show that the structural relaxation annealing enhances the hardness and that both the subsurface shear band number density and the plastic zone size decrease with annealing time. The serrations in the nanoindentation load-displacement curves become smoother with structural relaxation. Regardless of the annealing condition, the nanohardness of the deformed regions is similar to 12-15% lower, implying that the prior free volume only changes the yield stress (or hardness) but not the relative flow stress (or the extent of strain softening). Statistical distributions of the nanohardness obtained from deformed and undeformed regions have no overlap, suggesting that shear band number density has no influence on the plastic characteristics of the deformed region.

Growth and carcass characteristics of cast-for-age Merino ewes fed sorghum-based feedlot diets

Grain feeding low bodyweight, cast-for-age (CFA) sheep from pastoral areas of eastern Australia at the end of the growing season can enable critical carcass weight grades to be achieved and thus yield better economic returns. The aim of this work was to compare growth and carcass characteristics for CFA Merino ewes consuming either simple diets based on whole sorghum grain or commercial feed pellets. The experiment also compared various sources of additional nitrogen (N) for inclusion in sorghum diets and evaluated several introductory regimes. Seventeen ewes were killed initially to provide baseline carcass data and the remaining 301 ewes were gradually introduced to the concentrate diets over 14 days before being fed concentrates and wheaten hay ad libitum for 33 or 68 days. Concentrate treatments were: (i) commercial feed pellets, (ii) sorghum mix (SM; whole sorghum grain, limestone, salt and molasses) + urea and ammonium sulfate (SMU), (iii) SMU + whole cottonseed at 286 g/kg of concentrate dry matter (DM), (iv) SM + cottonseed meal at 139 g/kg of concentrate DM, (v) SMU + virginiamycin (20 mg/kg of concentrate) for the first 21 days of feeding, and (vi) whole cottonseed gradually replaced by SMU over the first 14 days of feeding. The target carcass weight of 18 kg was achieved after only 33 days on feed for the pellets and the SM + cottonseed meal diet. All other whole grain sorghum diets required between 33 and 68 days on feed to achieve the target carcass weight. Concentrates based on whole sorghum grain generally produced significantly (P < 0.05) lower carcass weight and fat score than pellets and this may have been linked to the significantly (P < 0.05) higher faecal starch concentrations for ewes consuming sorghum-based diets (270 v. 72 g/kg DM on day 51 of feeding for sorghum-based diets and pellets, respectively). Source of N in whole grain sorghum rations and special introductory regimes had no significant (P > 0.05) effects on carcass weight or fat score of ewes with the exception of carcass weight for SMU + whole cottonseed being significantly lower than SM + cottonseed meal at day 33. Ewes finished on all diets produced acceptable carcasses although muscle pH was high in all ewe carcasses (average 5.8 and 5.7 at 33 and 68 days, respectively). There were no significant (P > 0.05) differences between diets in concentrate DM intake, rumen fluid pH, meat colour score, fat colour score, eye muscle area, meat pH or meat temperature.

Toughness of as-cast and partially crystallized composites of a bulk metallic glass

The deformation and fracture response of a bulk metallic glass (BMG) post-annealing above the glass transition temperature is examined. The toughness of the glass-matrix composite exhibits a sharp transition beyond a critical volume fraction of crystallization to values as low as that of brittle silicate glass. Instrumented indentation tests supplemented by impact tests were used to study this ductile to brittle transition exhibited by the partially crystallized samples. Indentation on the anneal-embrittled specimens shows lateral cracks in addition to cracks along the corners. The applicability of the Poisson's ratio-toughness correlation with respect to partially crystallized samples is also investigated.

The machinability of a cast aluminium alloy-graphite particle composite

The microstructure of a cast Al---Si alloy-graphite particle composite is examined using optical and analytical scanning electron microscopy. Specimens containing different percentages of graphite were machined by orthogonal planning with 25° and 45° rake angle tools at both 6.5 and 13.2 m min−1. The machining forces are reported and the chip-rake-face friction coefficients and shear flow stresses are calculated. It is shown that the reduction in machining forces with increasing graphite content is due mostly to a decrease in the shear flow stress rather than to lower chip-rake-face friction. Both the polished and the machined surfaces of the composite are rougher than those of the simple alloy, apparently owing to the greater porosity, the tearing out of graphite particles, or the opening of cracks at the graphite particles in the wake of the tool.

Implications of co-twin dependence for twins' social interactions, mental health and alcohol use : A follow-up study of Finnish twins from adolescence to early adulthood

Objective: The aim of the present study was to examine co-twin dependence and its impact on twins' social contacts, leisure-time activities and psycho-emotional well-being. The role of co-twin dependence was also examined as a moderator of genetic and environmental influences on alcohol use in adolescence and in early adulthood. Methods: The present report is based on the Finnish Twin Cohort Study (FinnTwin16), a population-based study of five consecutive birth cohorts of Finnish twins born in the years 1975-1979. Baseline assessments were collected through mailed questionnaires, within two months of the twins' sixteenth birthday yielding replies from 5563 twin individuals. All respondent twins were sent follow-up questionnaires at ages of 17, 18½, and in early adulthood, when twins were 22-27 years old. Measures: The questionnaires included a survey of health habits and attitudes, a symptom checklist and questions about twins' relationships with parents, peers and co-twin. Measures used were twins' self-reports of their own dependence and their co-twin's dependence at age 16, reports of twins' leisure-time activities and social contacts, alcohol use, psychological distress and somatic symptoms both in adolescence and in early adulthood. Results: In the present study 25.6% of twins reported dependence on their co-twin. There were gender and zygosity differences in dependence, females and MZ twins were more likely to report dependence than males and DZ twins. Co-twin dependence can be viewed on one hand as an individual characteristic, but on the other hand as a pattern of dyadic interaction that is mutually regulated and reciprocal. Most of the twins (80.7%) were either concordantly co-twin dependent or concordantly co-twin independent. The associations of co-twin dependence with twins' social interactions and psycho-emotional characteristics were relatively consistent both in adolescence and in early adulthood. Dependence was related to higher contact frequency and a higher proportion of shared leisure-time activities between twin siblings at the baseline and the follow-up. Additionally co-twin dependence was associated with elevated levels of psycho-emotional distress and somatic complaints, especially in adolescence. In the framework of gene-environment interaction, these results suggest that the genetic contribution to individual differences in drinking patterns is dependent on the nature of the pair-wise relationship of twin siblings. Conclusions: The results of this study indicate that co-twin dependence is a genuine feature of the co-twin relationship and shows the importance of studying the impact of various features of co-twin relationships on individual twins' social and psycho-emotional life and well-being. Our study also offers evidence that differences in inter-personal relationships contribute to the effects of genetic propensities.