Examining the effect of exit separation on aircraft evacuation performance during 90-second certification trials using evacuation modelling techniques

This paper examines the influence of exit separation, exit availability and seating configuration on aircraft evacuation efficiency and evacuation time. The purpose of this analysis is to explore how these parameters influence the 60-foot exit separation requirement found in aircraft certification rules. The analysis makes use of the airEXODUS evacuation model and is based on a typical wide-body aircraft cabin section involving two pairs of Type-A exits located at either end of the section with a maximum permissible loading of 220 passengers located between the exits. The analysis reveals that there is a complex relationship between exit separation and evacuation efficiency. A main finding of this work is that for the cabin section examined, with a maximum passenger load of 220 and under certification conditions, exit separations up to 170ft will result in approximately constant total evacuation times and average personal evacuation times. This practical exit separation threshold is decreased to 114ft if another combination of exits is selected. While other factors must also be considered when determining maximum allowable exit separations, these results suggest it is not possible to mandate a maximum exit separation without taking into consideration exit type, exit availability and aircraft configuration.

A probabilistic methodology for distributed generation location in isolated electrical service area

Distributed generation unlike centralized electrical generation aims to generate electrical energy on small scale as near as possible to load centers, interchanging electric power with the network. This work presents a probabilistic methodology conceived to assist the electric system planning engineers in the selection of the distributed generation location, taking into account the hourly load changes or the daily load cycle. The hourly load centers, for each of the different hourly load scenarios, are calculated deterministically. These location points, properly weighted according to their load magnitude, are used to calculate the best fit probability distribution. This distribution is used to determine the maximum likelihood perimeter of the area where each source distributed generation point should preferably be located by the planning engineers. This takes into account, for example, the availability and the cost of the land lots, which are factors of special relevance in urban areas, as well as several obstacles important for the final selection of the candidates of the distributed generation points. The proposed methodology has been applied to a real case, assuming three different bivariate probability distributions: the Gaussian distribution, a bivariate version of Freund’s exponential distribution and the Weibull probability distribution. The methodology algorithm has been programmed in MATLAB. Results are presented and discussed for the application of the methodology to a realistic case and demonstrate the ability of the proposed methodology for efficiently handling the determination of the best location of the distributed generation and their corresponding distribution networks.

Improving cropping systems of semi-arid south-western Madagascar under multiple ecological and socio-economic constraints

Das Mahafaly Plateau im südwestlichen Madagaskar ist gekennzeichnet durch raue klimatische Bedingungen, vor allem regelmäßige Dürren und Trockenperioden, geringe Infrastruktur, steigende Unsicherheit, hohe Analphabetenrate und regelmäßige Zerstörung der Ernte durch Heuschreckenplagen. Da 97% der Bevölkerung von der Landwirtschaft abhängen, ist eine Steigerung der Produktivität von Anbausystemen die Grundlage für eine Verbesserung der Lebensbedingungen und Ernährungssicherheit in der Mahafaly Region. Da wenig über die Produktivität von traditionellen extensiven und neu eingeführten Anbaumethoden in diesem Gebiet bekannt ist, waren die Zielsetzungen der vorliegenden Arbeit, die limitierenden Faktoren und vielversprechende alternative Anbaumethoden zu identifizieren und diese unter Feldbedingungen zu testen. Wir untersuchten die Auswirkungen von lokalem Viehmist und Holzkohle auf die Erträge von Maniok, der Hauptanbaufrucht der Region, sowie die Beiträge von weiteren Faktoren, die im Untersuchungsgebiet ertragslimitierend sind. Darüber hinaus wurde in der Küstenregion das Potenzial für bewässerten Gemüseanbau mit Mist und Holzkohle untersucht, um zu einer Diversifizierung von Einkommen und Ernährung beizutragen. Ein weiterer Schwerpunkt dieser Arbeit war die Schätzung von Taubildung und deren Beitrag in der Jahreswasserbilanz durch Testen eines neu entworfenen Taumessgerätes. Maniok wurde über drei Jahre und in drei Versuchsfeldern in zwei Dörfern auf dem Plateau angebaut, mit applizierten Zeburindermistraten von 5 und 10 t ha-1, Holzkohleraten von 0,5 und 2 t ha-1 und Maniokpflanzdichten von 4500 Pflanzen ha-1. Maniokknollenerträge auf Kontrollflächen erreichten 1 bis 1,8 t Trockenmasse (TM) ha-1. Mist führte zu einer Knollenertragssteigerung um 30 - 40% nach drei Jahren in einem kontinuierlich bewirtschafteten Feld mit geringer Bodenfruchtbarkeit, hatte aber keinen Effekt auf den anderen Versuchsfeldern. Holzkohle hatte keinen Einfluss auf Erträge über den gesamten Testzeitraum, während die Infektion mit Cassava-Mosaikvirus zu Ertragseinbußen um bis zu 30% führte. Pflanzenbestände wurden felder-und jahresübergreifend um 4-54% des vollen Bestandes reduziert, was vermutlich auf das Auftreten von Trockenperioden und geringe Vitalität von Pflanzmaterial zurückzuführen ist. Karotten (Daucus carota L. var. Nantaise) und Zwiebeln (Allium cepa L. var. Red Créole) wurden über zwei Trockenzeiten mit lokal erhältlichem Saatgut angebaut. Wir testeten die Auswirkungen von lokalem Rindermist mit einer Rate von 40 t ha-1, Holzkohle mit einer Rate von 10 t ha-1, sowie Beschattung auf die Gemüseernteerträge. Lokale Bewässerungswasser hatte einen Salzgehalt von 7,65 mS cm-1. Karotten- und Zwiebelerträge über Behandlungen und Jahre erreichten 0,24 bis 2,56 t TM ha-1 beziehungsweise 0,30 bis 4,07 DM t ha-1. Mist und Holzkohle hatten keinen Einfluss auf die Erträge beider Kulturen. Beschattung verringerte Karottenerträge um 33% im ersten Jahr, während sich die Erträge im zweiten Jahr um 65% erhöhten. Zwiebelerträge wurden unter Beschattung um 148% und 208% im ersten und zweiten Jahr erhöht. Salines Bewässerungswasser sowie Qualität des lokal verfügbaren Saatgutes reduzierten die Keimungsraten deutlich. Taubildung im Küstendorf Efoetsy betrug 58,4 mm und repräsentierte damit 19% der Niederschlagsmenge innerhalb des gesamten Beobachtungszeitraum von 18 Monaten. Dies weist darauf hin, dass Tau in der Tat einen wichtigen Beitrag zur jährlichen Wasserbilanz darstellt. Tageshöchstwerte erreichten 0,48 mm. Die getestete Tauwaage-Vorrichtung war in der Lage, die nächtliche Taubildung auf der metallischen Kondensationsplatte zuverlässig zu bestimmen. Im abschließenden Kapitel werden die limitierenden Faktoren für eine nachhaltige Intensivierung der Landwirtschaft in der Untersuchungsregion diskutiert.

Evaluation of two hybrid metric-conceptual models, for simulating phosphorus transfer from agricultural land in the river enborne, a lowland UK catchment

Across Europe, elevated phosphorus (P) concentrations in lowland rivers have made them particularly susceptible to eutrophication. This is compounded in southern and central UK by increasing pressures on water resources, which may be further enhanced by the potential effects of climate change. The EU Water Framework Directive requires an integrated approach to water resources management at the catchment scale and highlights the need for modelling tools that can distinguish relative contributions from multiple nutrient sources and are consistent with the information content of the available data. Two such models are introduced and evaluated within a stochastic framework using daily flow and total phosphorus concentrations recorded in a clay catchment typical of many areas of the lowland UK. Both models disaggregate empirical annual load estimates, derived from land use data, as a function of surface/near surface runoff, generated using a simple conceptual rainfall-runoff model. Estimates of the daily load from agricultural land, together with those from baseflow and point sources, feed into an in-stream routing algorithm. The first model assumes constant concentrations in runoff via surface/near surface pathways and incorporates an additional P store in the river-bed sediments, depleted above a critical discharge, to explicitly simulate resuspension. The second model, which is simpler, simulates P concentrations as a function of surface/near surface runoff, thus emphasising the influence of non-point source loads during flow peaks and mixing of baseflow and point sources during low flows. The temporal consistency of parameter estimates and thus the suitability of each approach is assessed dynamically following a new approach based on Monte-Carlo analysis. (c) 2004 Elsevier B.V. All rights reserved.

Quantification of mitochondrial DNA mutation load

Mitochondrial DNA (mtDNA) mutations are an important cause of genetic disease and have been proposed to play a role in the ageing process. Quantification of total mtDNA mutation load in ageing tissues is difficult as mutational events are rare in a background of wild-type molecules, and detection of individual mutated molecules is beyond the sensitivity of most sequencing based techniques. The methods currently most commonly used to document the incidence of mtDNA point mutations in ageing include post-PCR cloning, single-molecule PCR and the random mutation capture assay. The mtDNA mutation load obtained by these different techniques varies by orders of magnitude, but direct comparison of the three techniques on the same ageing human tissue has not been performed. We assess the procedures and practicalities involved in each of these three assays and discuss the results obtained by investigation of mutation loads in colonic mucosal biopsies from ten human subjects.

Quantification of mitochondrial DNA mutation load

Mitochondrial DNA (mtDNA) mutations are an important cause of genetic disease and have been proposed to play a role in the ageing process. Quantification of total mtDNA mutation load in ageing tissues is difficult as mutational events are rare in a background of wild-type molecules, and detection of individual mutated molecules is beyond the sensitivity of most sequencing based techniques. The methods currently most commonly used to document the incidence of mtDNA point mutations in ageing include post-PCR cloning, single-molecule PCR and the random mutation capture assay. The mtDNA mutation load obtained by these different techniques varies by orders of magnitude, but direct comparison of the three techniques on the same ageing human tissue has not been performed. We assess the procedures and practicalities involved in each of these three assays and discuss the results obtained by investigation of mutation loads in colonic mucosal biopsies from ten human subjects.

A method of formulating energy load profile for domestic buildings in the UK

There are varieties of physical and behavioral factors to determine energy demand load profile. The attainment of the optimum mix of measures and renewable energy system deployment requires a simple method suitable for using at the early design stage. A simple method of formulating load profile (SMLP) for UK domestic buildings has been presented in this paper. Domestic space heating load profile for different types of houses have been produced using thermal dynamic model which has been developed using thermal resistant network method. The daily breakdown energy demand load profile of appliance, domestic hot water and space heating can be predicted using this method. The method can produce daily load profile from individual house to urban community. It is suitable to be used at Renewable energy system strategic design stage.

Evaluation and management of the impact of land use change on the nitrogen and phosphorus load delivered to surface waters: the export coefficient modelling approach

A manageable, relatively inexpensive model was constructed to predict the loss of nitrogen and phosphorus from a complex catchment to its drainage system. The model used an export coefficient approach, calculating the total nitrogen (N) and total phosphorus (P) load delivered annually to a water body as the sum of the individual loads exported from each nutrient source in its catchment. The export coefficient modelling approach permits scaling up from plot-scale experiments to the catchment scale, allowing application of findings from field experimental studies at a suitable scale for catchment management. The catchment of the River Windrush, a tributary of the River Thames, UK, was selected as the initial study site. The Windrush model predicted nitrogen and phosphorus loading within 2% of observed total nitrogen load and 0.5% of observed total phosphorus load in 1989. The export coefficient modelling approach was then validated by application in a second research basin, the catchment of Slapton Ley, south Devon, which has markedly different catchment hydrology and land use. The Slapton model was calibrated within 2% of observed total nitrogen load and 2.5% of observed total phosphorus load in 1986. Both models proved sensitive to the impact of temporal changes in land use and management on water quality in both catchments, and were therefore used to evaluate the potential impact of proposed pollution control strategies on the nutrient loading delivered to the River Windrush and Slapton Ley

Detection of recent changes in climate using meteorological data from south-eastern Bangladesh

Analysis of meteorological records from four stations (Chittagong, Cox’s Bazar, Rangamati, Sitakunda) in south-eastern Bangladesh show coherent changes in climate over the past three decades. Mean maximum daily temperatures have increased between 1980 and 2013 by ca. 0.4 to 0.6°C per decade, with changes of comparable magnitude in individual seasons. The increase in mean maximum daily temperature is associated with decreased cloud cover and wind speed, particularly in the pre- and post-monsoon seasons. During these two seasons, the correlation between changes in maximum temperature and clouds is between -0.5 and -0.7; the correlation with wind speed is weaker although similar values are obtained in some seasons. Changes in mean daily minimum (and hence mean) temperature differ between the northern and southern part of the basin: northern stations show a decrease in mean daily minimum temperature during the post-monsoon season of between 0.2 and 0.5°C per decade while southern stations show an increase of ca. 0.1 to 0.4°C per decade during the pre-monsoon and monsoon seasons. In contrast to the significant changes in temperature, there is no trend in mean or total precipitation at any station. However, there is a significant increase in the number of rain days at the northern sites during the monsoon season, with an increase per decade of 3 days in Sitakunda and 7 days at Rangamati. These climate changes could have a significant impact on the hydrology of the Halda Basin, which supplies water to Chittagong and is the major pisciculture centre in Bangladesh.

Fortified food made by the extrusion of a mixture of chickpea, corn and bovine lung controls iron-deficiency anaemia in preschool children

A fortified food that was rich in protein, vitamins and iron made of chickpea, bovine lung and corn was developed with the aim of controlling iron-deficiency anaemia in children from poorer areas. It was tested in Teresina, State of Piaui, Northeastern Brazil, on a population with high anaemia prevalence. Two local daycare units with similar characteristics were selected and the children at one of them received a 30 g pack three times a week, representing a total iron daily intake of 6.96 mg. The other daycare unit was followed as a control. The capillary haemoglobin concentration was determined for the children at both daycare units, at the beginning of the study and after a two-month intervention period. The mean haemoglobin concentration in the test group at the beginning of the intervention was 11.8 g/dL, which increased to 13.1 g/dL at the end of the intervention. In the control group these figures remained practically constant (11.6-11.8 g/dL). These represented a dramatic and significant drop in anaemia prevalence, from 61.5% to 11.5% in the test group, and an insignificant reduction (63.1-57.7%) in the control group. The acceptance of the fortified snack was excellent and no undesirable effects were observed. (C) 2007 Published by Elsevier Ltd.

Consórcio de guandu-anão com milheto: persistência e liberação de macronutrientes e silício da fitomassa

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Population parameters in Brazilian Thoroughbred

The information in this study has been provided by the Brazilian Association of Racehorse Breeders [Associação do Brasileira dos Criadores do Cavalo de Corrida (ABCCC)]. It can be found in the files on the CD-ROM developed by the ABCCC in 1999. A total of 5008 finishing time records related to 2545 winning horses that ran in the classical calendar on Brazilian hippodromes during 25 years (197498) were analysed. There were a total of 9949 horses on the relationship matrix. The variance components were estimated using the multiple-trait derivate-free restricted maximum likelihood (MTDFREML) program, for an animal model. Generation intervals were higher in the maternal side (10.91 years) than in the paternal one (10.41 years). The estimates for genetic permanent environmental and phenotypic variances and heritability were 0.291, 0.161, 3.486 and 0.08, respectively. The phenotypic standard deviation for time in races was 1.86729 s. Genetic time trend on Thoroughbred races in Brazil was small and could be accelerated if selection considered the trait time effectively. With respect to the animal's country of birth, the results show that there has been an intense participation of foreign animals in breeding Brazilian Thoroughbreds.

Effect of disinfection by microwave irradiation on the strength of intact and relined denture bases and the water sorption and solubility of denture base and reline materials

This study evaluated the influence of microwave disinfection on the strength of intact and relined denture bases. Water sorption and solubility were also evaluated. A heat-polymerized acrylic resin (Lucitone 550) was used to construct 4-mm-thick (n = 40) and 2-mm-thick (n = 160) denture bases. Denture bases (2mm) were relined with an autopolymerizing resin (Tokuso Rebase Fast, Ufi Gel Hard, Kooliner, or New Truliner). Specimens were divided into four groups (n = 10): without treatment, one or seven cycles of microwave disinfection (650 W for 6 min), and water storage at 37 degrees C for 7 days. Specimens were vertically loaded (5 mm/min) until failure. Disc-shaped specimens (50 min x 0.5 mm) were fabricated (n = 10) to evaluate water sorption and solubility. Data on maximum fracture load (N), deflection (%), and solubility (%) were analyzed by two-way analysis of variance and Student-Newman-Keuls tests (alpha = 0.05). One cycle of microwave disinfection decreased the deflection at fracture and fracture energy of Tokuso Rebase Fast and New Truliner specimens. The strength of denture bases microwaved daily for 7 days was similar to the strength of those immersed in water for 7 days. Microwave disinfection increased the water sorption of all materials and affected the solubility of the reline materials. (C) 2007 Wiley Periodicals, Inc.

Spectral analysis of the electromyograph of the erector spinae muscle before and after a dynamic manual load-lifting test

The aim of the present study was to assess the spectral behavior of the erector spinae muscle during isometric contractions performed before and after a dynamic manual load-lifting test carried out by the trunk in order to determine the capacity of muscle to perform this task. Nine healthy female students participated in the experiment. Their average age, height, and body mass (± SD) were 20 ± 1 years, 1.6 ± 0.03 m, and 53 ± 4 kg, respectively. The development of muscle fatigue was assessed by spectral analysis (median frequency) and root mean square with time. The test consisted of repeated bending movements from the trunk, starting from a 45º angle of flexion, with the application of approximately 15, 25 and 50% of maximum individual load, to the stand up position. The protocol used proved to be more reliable with loads exceeding 50% of the maximum for the identification of muscle fatigue by electromyography as a function of time. Most of the volunteers showed an increase in root mean square versus time on both the right (N = 7) and the left (N = 6) side, indicating a tendency to become fatigued. With respect to the changes in median frequency of the electromyographic signal, the loads used in this study had no significant effect on either the right or the left side of the erector spinae muscle at this frequency, suggesting that a higher amount and percentage of loads would produce more substantial results in the study of isotonic contractions.

Importantes características de chuva para a conservação do solo e da água no município de São Manuel (SP)

Os modelos matemáticos preditivos da erosão do solo, como a Equação Universal de Perda de Solo (EUPS), são de muita valia no planejamento de uso agrícola da terra. Tal equação, desenvolvida para estimar as perdas médias anuais de solo esperadas em dado local, para determinado sistema de manejo, apresenta como variáveis os fatores erosividade da chuva (R), erodibilidade do solo (K), comprimento do declive (L), grau do declive (S), cobertura e manejo (C) e práticas conservacionistas de suporte (P). Com o objetivo de contribuir para o planejamento conservacionista de uso do solo local, foi estimado, de forma simplificada, o fator erosividade da chuva (R) da EUPS para o município de São Manuel (SP), para uma série pluviométrica contínua de 49 anos de dados de chuva diária. Além disso, foram também calculados o período de retorno, a freqüência de ocorrência dos índices de erosividade anuais e as quantidades máximas diárias das chuvas necessárias para o dimensionamento mais adequado de canais de terraços agrícolas em nível. O valor calculado do fator R foi de 7.487 MJ mm ha-1 h-1 ano-1, esperado ocorrer no local, pelo menos, uma vez a cada 2,33 anos, com uma probabilidade de 42,92 %. Observou-se uma concentração de 81,48 % do valor total deste fator no semestre de outubro a março, indicando que, potencialmente, as maiores perdas anuais de solo por erosão são esperadas neste período. Os valores anuais do índice EI30, esperados para os períodos de retorno de 2, 5, 10, 20, 50 e 100 anos, foram de 7.216, 8.675, 9.641, 10.568, 11.768 e 12.667 MJ mm ha-1 h-1 ano-1, respectivamente. Com relação às quantidades máximas de chuva diária, para os mesmos períodos de retorno, os valores foram de 73, 98, 115, 131, 151 e 167 mm, respectivamente.