Bonding of aluminum alloy by hot-dipping tin coating

This paper presents bonding technology of aluminum alloy by hot-dipping tin. The dissolution curve of copper in molten tin liquid was obtained in the experiment of hot-dipping Sn. Optimal hot-dipping parameter which was suitable for soldering was designed. To elucidate characteristics of interfacial evolution, the microstructure of the coatings, soldered joint were analyzed using optical microscopy, SEM and EDX. The shear strength of soldered joints was tested as high as 39.9Mpa, which is high enough to achieve the requirement of electronic industry.

Organic photovoltaics using thin gold film as an alternative anode to indium tin oxide

Indium Tin Oxide (ITO) is the most commonly used anode as a transparent electrode and more recently as an anode for organic photovoltaics (OPVs). However, there are significant drawbacks in using ITO which include high material costs, mechanical instability including brittleness and poor electrical properties which limit its use in low-cost flexible devices. We present initial results of poly(3-hexylthiophene): phenyl-C61-butyric acid methyl ester OPVs showing that an efficiency of 1.9% (short-circuit current 7.01 mA/cm2, open-circuit voltage 0.55 V, fill factor 0.49) can be attained using an ultra thin film of gold coated glass as the device anode. The initial I-V characteristics demonstrate that using high work function metals when the thin film is kept ultra thin can be used as a replacement to ITO due to their greater stability and better morphological control.

Development of thermoelectric gas sensors for volatile organic compounds

This paper describes the design and development of a thermoelectric gas sensor suitable for the detection of Volatile Organic Compounds (VOCs). In order to enhance the seebeck coefficient of the sensor, we have deposited chromium metal films on a limited area of the glass substrate. Tin oxide thin film was deposited on top of these metal films. The resulting metal/semiconductor film exhibits a high seebeck coefficient of 400 mu V/ degrees C. Platinum catalyst film deposited on the oxide film to create the necessary temperature gradient resulted in further enhancement in the sensitivity of the sensor to target gases. The sensor shows high sensitivity to ppm-change in the concentration of target hydrocarbons at a relatively low temperature of 120 degrees C.

Effect of TiN particulate reinforcement on corrosive behaviour of aluminium 6061 composites in chloride medium

In the present investigation, the corrosive behaviour of Al 6061-TiN particulate composites prepared by liquid metallurgy has been studied in chloride medium using electroanalytical techniques such as Tafel, cyclic polarization and electrochemical impedance spectroscopy (EIS). Surface morphology of the sample electrodes was examined using scanning electron micrography and energy dispersive X-ray methods. X-ray diffraction technique was used to confirm inclusion of TiN particulates in the matrix alloy and identify the alloying elements and intermetallic compounds in the Al 6061 composites. Polarization studies indicate an increase in the corrosion resistance in composites compared to the matrix alloy. EIS study reveals that the polarization resistance (R (p)) increases with increase in TiN content in composites, thus confirming improved corrosion resistance in composites. The observed decrease in corrosion rate in the case of composites is due to decoupling between TiN particles and Al 6061 alloy. It is understood that after the initiation of corrosion, interfacial corrosion products may have decoupled the conducting ceramic TiN from Al 6061 matrix alloy thus eliminating the galvanic effect between them.

Molecular mechanics calculations of tin-bis (triphenylphosphine oxide) complexes

The capability of molecular mechanics for modeling the wide distribution of bond angles and bond lengths characteristic of coordination complexes was investigatecl. This was the preliminary step for future modeling of solvent extraction. Several tin-phosphine oxide COrnI)le:){es were selected as the test groUl) for t.he d,esired range of geometry they eX!libi ted as \-vell as the ligands they cOD.tained r Wllich were c\f interest in connection with solvation. A variety of adjustments were made to Allinger's M:M2 force·-field ill order to inl.prove its performance in the treatment of these systems. A set of u,nique force constants was introduced for' those terms representing the metal ligand bond lengths, bond angles, and, torsion angles. These were significantly smaller than trad.itionallY used. with organic compounds. The ~1orse poteIlt.ial energ'Y function was incorporated for the M-X l')ond lE~ngths and the cosine harmonic potential erlerg-y function was invoked for the MOP bond angle. These functions were found to accomodate the wide distribution of observed values better than the traditional harmonic approximations~ Crystal packing influences on the MOP angle were explored thr"ollgh ttle inclusion of the isolated molecule withil1 a shell cc)ntaini11g tl1e nearest neigl1'bors duri.rlg energy rninimization experiments~ This was found to further improve the fit of the MOP angle.

Growth and characterisation of tin dichalcogenide crystals

During the past few decades, a wide spread interest in the structural, optical, electrical and other physical properties of the transition metal dichalcogenide layer compounds has evolved. The members of this family of compounds can be regarded as strongly bonded two dimensional chalcogen-metal~chalcogen layers which are loosely coupled to one another by the weak ven der Waal's forces. Because of this type of bonding, the crystals are easily cleavable along the basal plane and show highly anisotropic properties. This thesis contains the growth and the study of the physical properties of certain tin dichalcogenide crystals (SnS2 and SnSe2). Tin disulphide and tin diselenide crystallize in the hexagonal CdI2 type crystal structure. This structure consists of layers of tin atoms sandwiched between two layers of chalcogen atoms. A tin atom is surrounded by six chalcogen atoms octahedrally.In the layers the atoms are held together by covalent bonding and in between the layers there is van der Waal's bonding.

Growth and characterisation of tin dichalcogenide crystals

During the past few decades, a wide spread interest in the structural, optical, electrical and other physical properties of the transition metal dichalcogenide layer compounds has evolved. The members of this family of compounds can be regarded as stronglybonded two dimensional chalcogen-metal-chalcogen layers which are loosely coupled to one another by the weak van der Waal's forces. Because of this type of bonding, the crystals are easily cleavable along the basal plane and show highly anisotropic properties. This thesis contains the growth and the study of the physical properties of certain tin dichalcogenide crystals (SnS2 and Snsea). Tin disulphide and tin diselenide crystallize in the hexagonal CdI2 type crystalstructure. This structure consists of layers of tin atoms sandwiched between two layers of chalcogen atoms. Aitin atom is surrounded by six chalcogen atoms octahedrally. In the layers the atoms are held together by covalent bonding and in between the layers there is van der Waal's bonding.

Investigations On The Preparation And Properties Of Reactively Evaporated Lead Sulphide And Tin Telluride Thin Films

The work reported in this thesis is the preparation, and the structural, electrical and optical properties of reactively evaporated lead sulphide and tin telluride thin films. The three temperature method had been used for the preparation of these semiconductor thin films. In this preparation technique constituent elements are evaporated from separate sources with the substrate kept at a particular temperature. when one of the constituent element is a gas near room temperature, the method is often called reactive evaporation. It has been found for many materials that a stoichiometric interval exists with a limited range of flux and substrate temperature. Usually this technique is used for the preparation of thin films of high melting point compounds or of materials which decompose during evaporation. Tin telluride and lead sulphide are neither high melting point materials nor do they decompose on melting. But even than reactive evaporation offers the possibility of changing the ratios of the flux of the constituent elements within a wide range and studying its effect on the properties of the films

Investigation of tin-based alternatives for cadmium in optoelectronic thin-films materials

Increasing legislation has steadily been introduced throughout the world to restrict the use of heavy metals, particularly cadmium (Cd) and lead (Pb) in high temperature pigments, ceramics, and optoelectronic material applications. Removal of cadmium from thin-film optical and semiconductor device applications has been hampered by the absence of viable alternatives that exhibit similar properties with stability and durability. We describe a range of tin-based compounds that have been deposited and characterized in terms of their optical and mechanical properties and compare them with existing cadmium-based films that currently find widespread use in the optoelectronic and semiconductor industries. (c) 2008 Optical Society of America.

Synthesis, properties, and X-ray crystal and molecular structures of homoleptic alkenyls of tin and chromium

Reaction of Li(CPhCMe2) with SnCl4 or CrCl3·3thf (thf = tetrahydrofuran) affords the isoleptic compounds Sn(CPhCMe2)4 or [Cr(CPhCMe2)4] respectively. The mode of formation and chemical properties are reported for the chromium species, and the structures of the new compounds, both of which have been determined by single-crystal X-ray analysis, are described.

Synthesis, characterisation, Mössbauer spectra, and structures of some trinuclear iron-tin clusters

Reactions of [Fe3(CO)12] with diaryltin species SnR2(R1= 2,4,6-triisopropylphenyl, R2= 2,6-diethylphenyl, R3= pentamethylphenyl) and with Sn[CH(PPh2)2]2 have been investigated. The tin reagents SnR2(R = R1 or R2) reacted under mild conditions to give in moderate yields the trinuclear species [Fe2(CO)8(µ-SnR12)]1 or [Fe2(CO)8(µ-SnR22)]2, as orange-red crystalline solids, which decompose in air on prolonged exposure. The compound [Fe2(CO)8(µ-SnR42)]3(R4= 2,4,6-triphenylphenyl) can be similarly obtained. Prolonged treatment of the carbonyl with the novel tin reagent SnR32, by contrast, afforded the known compound spiro-[(OC)8Fe2SnFe2(CO)8]4 for which data are briefly reported. Reactions with tin or lead reagents M[CH(PPh2)2]2(M = Sn or Pb) afforded [Fe2(CO)6(µ-CO)(µ-dppm)][dppm = 1,2-bis(diphenylphosphino)methane] rapidly and almost quantitatively. Full crystal and molecular structural data are reported for [Fe2(CO)8(µ-SnR12)] and [Fe2(CO)8(µ-SnR22)]. Mössbauer data are also presented for compounds 1–3, and interpreted in terms of the structural data for these and other systems.

Hypercoordinated organotin compounds containing sulfur and chlorine. Molcular structures of [(Ph3P)2N]+[S(SnR2Cl)2Cl]- (R=Me, t-Bu)

The reaction of diorganotin sulfides, cyclo-(R₂SnS)_n (R=Me, n-Bu; n=3; R=t-Bu; n=2) with the corresponding diorganotin dichlorides, R₂SnCl₂, provided the tetraorganodistannathianes, (R₂ClSn)₂S (1, R=Me; 2, R=n-Bu; 3, R=t-Bu). ¹H-, ¹³C-, and ¹¹⁹Sn-NMR studies indicate that these compounds are kinetically labile and in equilibrium with the starting materials. Addition of equimolar amounts of [(Ph₃P)₂N]Cl to the reaction mixtures gave the chloride complexes [(Ph₃P)₂N]⁺[S(SnR₂Cl)₂Cl]⁻ (4, R=Me; 5, R=n-Bu; 6, R=t-Bu). Single-crystal X-ray diffraction studies revealed the tin atoms in both 4 and 6 to adopt distorted trigonal bipyramidal configurations with the chlorine atoms occupying the axial positions.

Steric control over molecular structure and supramolecular association exerted by tin- and ligand-bound groups in diorganotin carboxylates

Structural data (X-ray and solution and solid-state ^₁₁₉Sn NMR) show that skew-trapezoidal-bipyramidal diorganotin compounds of 2-quinaldate are invariably monomeric, owing to the steric bulk of the carboxylate ligand. In contrast, most of the analogous compounds of 2-picolinate (2-pic) can increase their coordination number by polymerization or the incorporation of solvent in their coordination sphere in the solid state. The exceptional compound is tBu₂Sn(2-pic)₂ (3), for which no increase in coordination number is apparent, a result that is correlated with the bulky tert-butyl groups. Thus, judicious choice of tin or ligand substituents can be exploited to dictate coordination number and/or the degree of supramolecular aggregation in the investigated systems.

Hydrolysis of bis((trimethylsilyl)methyl)tin dihalides. Crystallographic and spectroscopic study of the hydrolysis pathway

The synthesis and characterization by multinuclear NMR spectroscopy of the diorganotin dihalides (Me₃SiCH₂)₂SnX₂ (1, X = Cl; 2, X = Br), the diorganotin dichloride water adduct (Me₃SiCH₂)₂SnCl₂·H₂O (1a), the dimeric tetraorganodistannoxanes [(Me₃SiCH₂)₂(X)SnOSn(Y)(CH₂SiMe₃)₂]₂ (3, X = Y = Cl; 4, X = Br, Y = OH; 5, X = Br, Y = F; 6, X = Y = OH; 8, X = Cl, Y = OH), and the molecular diorganotin oxide cyclo-[(Me₃SiCH₂)₂SnO]₃ (7) are reported. The structures in the solid state of compounds 1a, 3, 6, and 7 were determined by single-crystal X-ray analysis. In toluene solution, the hydroxy-substituted tetraorganodistannoxane 6 is in equilibrium with the diorganotin oxide 7 and water. The eight-membered diorganotin oxide cyclo-[(Me₃SiCH₂)₂SnO]₄ (7a) is proposed to be involved in this equilibrium. On the basis of the results of this and previous works, a general hydrolysis pathway is developed for diorganotin dichlorides containing reasonably bulky substituents.

Novel 10- and 20- membered tin- and silicon-containing rings: synthesis, complexation behavior and conversion into a lewis acidic polymer

Reaction of the dimethylsilylmethyl-substituted tetraorganotin derivative CH₂[CH₂Sn(Ph₂)CH₂Si(H)Me₂]₂ (1) and CH₂[CH₂Sn(Ph₂)CH₂Si(i-PrO)Me₂]₂ (3), respectively, with mercuric chloride afforded the novel silicon- and tin-containing 10- and 20-membered rings cyclo-CH₂[CH₂Sn(Cl₂)CH₂Si(Me₂)]₂O (4) and cyclo-CH₂[CH₂Sn(Cl₂)CH₂Si(Me₂)OSi(Me₂)CH₂Sn(Cl₂)CH₂]₂CH₂ (5). Both compounds 4 and 5 can be converted into the soluble Lewis acidic polymer poly-[Si(Me₂)CH₂Sn(Cl₂)(CH₂)₃Sn(Cl₂)CH₂Si(Me₂)O] (8). ¹¹⁹Sn NMR studies indicate that 4 acts as a bidentate Lewis acid toward chloride ions, exclusively forming the 1:1 complex [cyclo-CH₂[CH₂Sn(Cl₂)CH₂Si(Me₂)]₂O·Cl]-[(Ph₃P)₂N]⁺ (7). The molecular structures as determined by single-crystal X-ray diffraction analysis of 4 and 7 are reported.