A comparative performance study of four-pole induction motors and synchronous reluctance motors in variable speed drives

Design aspects of the Transversally Laminated Anisotropic (TLA) Synchronous Reluctance Motor (SynRM) are studied and the machine performance analysis compared to the Induction Motor (IM) is done. The SynRM rotor structure is designed and manufactured for a30 kW, four-pole, three-phase squirrel cage induction motor stator. Both the IMand SynRM were supplied by a sensorless Direct Torque Controlled (DTC) variablespeed drive. Attention is also paid to the estimation of the power range where the SynRM may compete successfully with a same size induction motor. A technicalloss reduction comparison between the IM and SynRM in variable speed drives is done. The Finite Element Method (FEM) is used to analyse the number, location and width of flux barriers used in a multiple segment rotor. It is sought for a high saliency ratio and a high torque of the motor. It is given a comparison between different FEM calculations to analyse SynRM performance. The possibility to take into account the effect of iron losses with FEM is studied. Comparison between the calculated and measured values shows that the design methods are reliable. A new application of the IEEE 112 measurement method is developed and used especially for determination of stray load losses in laboratory measurements. The study shows that, with some special measures, the efficiency of the TLA SynRM is equivalent to that of a high efficiency IM. The power factor of the SynRM at rated load is smaller than that of the IM. However, at lower partial load this difference decreases and this, probably, brings that the SynRM gets a better power factor in comparison with the IM. The big rotor inductance ratio of the SynRM allows a good estimating of the rotor position. This appears to be very advantageous for the designing of the rotor position sensor-less motor drive. In using the FEM designed multi-layer transversally laminated rotor with damper windings it is possible to design a directly network driven motor without degrading the motorefficiency or power factor compared to the performance of the IM.

Implementation of Signaling Gateway between Telephone Network and the Internet

Tässä diplomityössä perehdytään verkkoelementiltä, joka yhdistää H.323, MEGACO- ja ISUP-protokollia käyttävät tietoliikenneverkot toisiinsa, vaadittaviin ominaisuuksiin ja toiminnallisuuksiin. Tyypillisesti tällaista toiminnallisuutta tarvitaan IP- ja PSTN-verkkojen yhdistämisessä. Tarkastelu aloitetaan kuvaamalla PSTN-verkon signalointi ja rakenne, jatketaan kuvaamalla internet-protokollia käyttävä verkkoympäristö ja lopuksi perehdytään verkkoelementiltä vaadittaviin toiminnallisuuksiin, jotta PSTN ja MEGACO-pohjaiset verkot toimivat yhteen. Työn käytännöllisenä osuutena kuvataan osa viestisekvenssikaavioista, joita verkkoelementti toteuttaa puuttumatta kuitenkaan eri protokollien toimintaan viestien parametrien tasolla.

Undercoverage and Nonresponse in a List-sampled Telephone Election Survey

For landline telephone surveys in particular, undercoverage has been a growing problem. However, research regarding the relative contributions of socio-demographic bias and other composition effects is scarce. We propose to address this issue by analyzing an election survey which used a sample from a register-based sampling frame containing basic socio-demographic information and to which telephone numbers were subsequently matched. With respect to socio-demographic representation of the final sample, we find that difficult to match groups are also difficult to contact, while those who cooperate tend to have different characteristics. We find bias due to undercoverage to be of greater magnitude than noncontact bias, while noncooperation falls between the two. As for substantive variables, both additional efforts to match missing telephone numbers and the construction of better weights are successful in closing the gap between survey estimates of voting behavior and true values from the election results.

Salient Pole Synchronous Machine Modelling in an Industrial Direct Torque Controlled Drive Application

Synchronous motors are used mainly in large drives, for example in ship propulsion systems and in steel factories' rolling mills because of their high efficiency, high overload capacity and good performance in the field weakening range. This, however, requires an extremely good torque control system. A fast torque response and a torque accuracy are basic requirements for such a drive. For large power, high dynamic performance drives the commonly known principle of field oriented vector control has been used solely hitherto, but nowadays it is not the only way to implement such a drive. A new control method Direct Torque Control (DTC) has also emerged. The performance of such a high quality torque control as DTC in dynamically demanding industrial applications is mainly based on the accurate estimate of the various flux linkages' space vectors. Nowadays industrial motor control systems are real time applications with restricted calculation capacity. At the same time the control system requires a simple, fast calculable and reasonably accurate motor model. In this work a method to handle these problems in a Direct Torque Controlled (DTC) salient pole synchronous motor drive is proposed. A motor model which combines the induction law based "voltage model" and motor inductance parameters based "current model" is presented. The voltage model operates as a main model and is calculated at a very fast sampling rate (for example 40 kHz). The stator flux linkage calculated via integration from the stator voltages is corrected using the stator flux linkage computed from the current model. The current model acts as a supervisor that prevents only the motor stator flux linkage from drifting erroneous during longer time intervals. At very low speeds the role of the current model is emphasised but, nevertheless, the voltage model always stays the main model. At higher speeds the function of the current model correction is to act as a stabiliser of the control system. The current model contains a set of inductance parameters which must be known. The validation of the current model in steady state is not self evident. It depends on the accuracy of the saturated value of the inductances. Parameter measurement of the motor model where the supply inverter is used as a measurement signal generator is presented. This so called identification run can be performed prior to delivery or during drive commissioning. A derivation method for the inductance models used for the representation of the saturation effects is proposed. The performance of the electrically excited synchronous motor supplied with the DTC inverter is proven with experimental results. It is shown that it is possible to obtain a good static accuracy of the DTC's torque controller for an electrically excited synchronous motor. The dynamic response is fast and a new operation point is achieved without oscillation. The operation is stable throughout the speed range. The modelling of the magnetising inductance saturation is essential and cross saturation has to be considered as well. The effect of cross saturation is very significant. A DTC inverter can be used as a measuring equipment and the parameters needed for the motor model can be defined by the inverter itself. The main advantage is that the parameters defined are measured in similar magnetic operation conditions and no disagreement between the parameters will exist. The inductance models generated are adequate to meet the requirements of dynamically demanding drives.

Design and analysis of a transversal-flux switched-reluctance-linear-machine pole-pair

The Switched Reluctance technology is probably best suited for industrial low-speed or zerospeed applications where the power can be small but the torque or the force in linear movement cases might be relatively high. Because of its simple structure the SR-motor is an interesting alternative for low power applications where pneumatic or hydraulic linear drives are to be avoided. This study analyses the basic parts of an LSR-motor which are the two mover poles and one stator pole and which form the “basic pole pair” in linear-movement transversal-flux switchedreluctance motors. The static properties of the basic pole pair are modelled and the basic design rules are derived. The models developed are validated with experiments. A one-sided one-polepair transversal-flux switched-reluctance-linear-motor prototype is demonstrated and its static properties are measured. The modelling of the static properties is performed with FEM-calculations. Two-dimensional models are accurate enough to model the static key features for the basic dimensioning of LSRmotors. Three-dimensional models must be used in order to get the most accurate calculation results of the static traction force production. The developed dimensioning and modelling methods, which could be systematically validated by laboratory measurements, are the most significant contributions of this thesis.

Design of salient pole PM synchronous machines for a vehicle traction application – Analysis and

This doctoral thesis presents a study on the development of a liquid-cooled frame salient pole permanent-magnet-exited traction machine for a four-wheel-driven electric car. The emphasis of the thesis is put on a radial flux machine design in order to achieve a light-weight machine structure for traction applications. The design features combine electromagnetic and thermal design methods, because traction machine operation does not have a strict operating point. Arbitrary load cycles and the flexible supply require special attention in the design process. It is shown that accurate modelling of the machine magnetic state is essential for high-performance operation. The saturation effect related to the cross-saturation has to be taken carefully into account in order to achieve the desired operation. Two prototype machines have been designed and built for testing: one totally enclosed machine with a special magnet module pole arrangement and another through-ventilated machine with a more traditional embedded magnet structure. Both structures are built with magnetically salient structures in order to increase the torque production capability with the reluctance torque component. Both machine structures show potential for traction usage. However, the traditional embedded magnet design turns out to be mechanically the more secure one of these two machine options.

Productivity and Services – Safety Telephone Services for the Elderly

Previous research on productivity is often associated with manufacturing or uses manufacturing definitions of productivity. Marketing research on services has not been satisfied with the manufacturing definitions. No universal definition for service productivity exists. The lack of a universal definition highlights the complexity entailed in the concept of productivity. The objective of this study was to investigate service productivity in situations, where traditional ways are in some cases even not possible or are not enough. In one definition of the productivity of service organisations there is the efficiency of the organisation on the input side and on the output side the customers’ perceived quality or value-in-use. To learn about value-in-use, many methods have been developed. A common practice is to make customer opinion surveys in the form of customer questionnaires and interviews. However, customers cannot always be asked directly, for example, because of impaired cognitive abilities. Such cases include the elderly and children. Furthermore, customer opinion surveys are time consuming. In addition, customers do not always know what kind of services they would benefit from. For the empirical part of the study, a business area was identified where traditional ways of measuring value-in-use are difficult or in some cases even not possible. This business area is safety telephone services. These services are most often used by the elderly. The way to define value-in-use here was to assess how well the services offered met customer expectations. Comparing the services customers asked for and the services provided to them indicated whether customer expectations were met. This study showed that customers had their ideas concerning the contents of the services but many times the services provided did not meet these expectations. Organisational efficiency aspirations can decrease customers’ value-in-use. This study found a solution, in which increasing organisational efficiency would go hand-in-hand with increasing customers’ value-in-use; the result being that the organisations’ needs and the service users’ expectations were in line. Value creation for customers produced organisational efficiency and thus increased productivity. In this study, customer expectations were observed by means of wellness technology. With the help of modern technology, customer expectations can be followed quickly and easily and customers can co-create with the organisation. This type of an approach could be useful even in the development of other services for other ages and in different contexts. If a service organisation decreases the number of personnel and, at the same time, tries to offer services to the same or a larger clientele, customers easily notice the change, which is often negative. To avoid harmful decrease in value-in-use, limitations to the aspiration of efficiency should be implemented – one of such is that the organisation is required to meet certain quality standards defined by experts. The aim is to secure that, as a result of efficiency aspirations in the organisation, the quality of the service offerings does not diminish below mutually agreed standards. Traditionally, when productivity in services has been estimated, organisational efficiency has not been combined with both customer expectations and an expert assessment of quality. This study contributes with novel thinking entitled ‘Relationship Management of the Elderly’. This study handles productivity, expert defined quality and value-in-use in an organisational context, which is practically untouched in previous research studies.

A new & accurate map of the North Pole with all the countries hitherto discovered situated near or adjacent to it as well as some others more remote. Drawn from the latest and best authorities and regulated by astronom.l observat.ns by Eman. Bowen.

0-meridiaani: Lontoo. - Koordinaattiasteikko: N90°-55°[50°].

Receipt from the Bell Telephone Co. for telephone apparatus at Ontario Street

Receipt from the Bell Telephone Co. for telephone apparatus at Ontario Street, Jan 9, 1887.

La recherche de « sexiness » chez les adeptes de pole-fitness : une étude de terrain montréalais

Cette étude explore la transformation des critères normatifs qui donnent accès au statut de femmes respectables à travers le concept de nouveau sujet féminin discuté par Radner (1999), Gill (2008; 2012) et McRobbie (1993; 2009) où l’idée de recherche active de « sexiness » chez les femmes à l’époque contemporaine est centrale. Le post-féminisme, une formation discursive qui émerge dans les années 1980, est identifié comme étant à l’origine de ces transformations. Cette position identitaire permettrait aux femmes de résister aux stigmates attachés à celles qui se posent comme sujet sexuel actif plutôt que comme objet sexuel passif et conduirait ainsi à l’« empowerment » sexuel. Or, cette vision du nouveau sujet féminin est contestée puisqu’elle ne représenterait qu’une seule possibilité d’émancipation à travers le corps et deviendrait par sa force normative un nouveau régime disciplinaire du genre féminin. L’interprétation valable à donner au nouveau sujet féminin représente un débat polarisé dans les milieux féministes et ce mémoire cherche à y apporter des éléments de discussion par l’étude des motivations des femmes à s’inscrire à des cours de pole-fitness et des significations qu’elles donnent à leur pratique. Ce mémoire apporte des éléments à la compréhension de l’impact de cette recherche de « sexiness » sur la subjectivité des femmes à travers les concepts de pratiques disciplinaires et stratégies de résistance.

Microstrip antennas for mobile telephone handset with reduced radiation hazards

A novel antenna configuration comprised of two circular micro strip antennas (CMAs) resonating in the TMtt and TM2, modes, producing radiation characteristics suitable for a mobile telephone handset, is presented. The antennas operating at the same frequency are placed back to back with a separation comparable to the thickness of a typical handset. The radiation pattern consists of a region of reduced radiation intensity, which minimizes the radiation hazards to the user

Microstrip Antennas For Mobile Telephone Handset With Reduced Radiation Hazards

A novel antenna configuration comprised of two circular microstrip antennas (CMAs) resonating in the TMtt and TM2, modes, producing radiation characteristics suitable for a mobile telephone handset, is presented. The antennas operating at the same frequency are placed back to back with a separation comparable to the thickness of a typical handset. The radiation pattern consists of a region of reduced radiation intensity, which minimizes the radiation hazards to the user

The effects of varying amounts of visual information on telephone intelligibility

This study examines whether similarly reduced amounts of visible articulatory information has potential for increasing speech intelligibility over the telephone to hearing-impaired listeners.