The crack tip strain field of AISI 4340 - Part III - Hydrogen influence

This paper studied the influence of hydrogen and water vapour environments on the plastic behaviour in the vicinity of the crack tip for AISI 4340. Hydrogen and water vapour (at a pressure of 15 Torr) significantly increased the crack tip opening displacement. The crack tip strain distribution in 15 Torr hydrogen was significantly different to that measured in vacuum. In the presence of sufficient hydrogen, the plastic zone was larger, was elongated in the direction of crack propagation and moreover there was significant creep. These observations support the hydrogen enhanced localised plasticity model for hydrogen embrittlement in this steel. The strain distribution in the presence of water vapour also suggests that SCC in AISI 4340 occurs via the hydrogen enhanced localised plasticity mechanism. (C) 1999 Kluwer Academic Publishers.

Strain-dependent fluid flow defined through rock mass classification schemes

Strain-dependent hydraulic conductivities are uniquely defined by an environmental factor, representing applied normal and shear strains, combined with intrinsic material parameters representing mass and component deformation moduli, initial conductivities, and mass structure. The components representing mass moduli and structure are defined in terms of RQD (rock quality designation) and RMR (rock mass rating) to represent the response of a whole spectrum of rock masses, varying from highly fractured (crushed) rock to intact rock. These two empirical parameters determine the hydraulic response of a fractured medium to the induced-deformations The constitutive relations are verified against available published data and applied to study one-dimensional, strain-dependent fluid flow. Analytical results indicate that both normal and shear strains exert a significant influence on the processes of fluid flow and that the magnitude of this influence is regulated by the values of RQD and RMR.

The moderating role of social support in Karasek's job strain model

This paper examines whether social support is a boundary-determining criterion in the job strain model of Karasek (1979). The particular focus is the extent to which different sources of social support, work overload and task control influence job satisfaction, depersonalization and supervisor assessments of work performance. Hypotheses are tested using prospective survey data from 80 clerical staff in a university setting. Results revealed 3-way interactions among levels of support (supervisor, co-worker, non-work), perceived task control and work overload on levels of work performance and employee adjustment (self-report). After controlling for levels of negative affect in all analyses, there was evidence that high levels of supervisor support mitigated against the negative effects of high strain jobs on levels of job satisfaction and reduced reported levels of depersonalization. Moreover, high levels of non-work support and co-worker support also mitigated against the negative effects of high strain jobs on levels of work performance. The results are discussed in terms of the importance of social support networks both at, and beyond, the work context.

Apparent strain localization and shear wave dispersion in elastic fault gouge with microrotations

Shear deformation of fault gouge or other particulate materials often results in observed strain localization, or more precisely, the localization of measured deformation gradients. In conventional elastic materials the strain localization cannot take place therefore this phenomenon is attributed to special types of non-elastic constitutive behaviour. For particulate materials however the Cosserat continuum which takes care of microrotations independent of displacements is a more appropriate model. In elastic Cosserat continuum the localization in displacement gradients is possible under some combinations of the generalized Cosserat elastic moduli. The same combinations of parameters also correspond to a considerable dispersion in shear wave propagation which can be used for independent experimental verification of the proposed mechanism of apparent strain localization in fault gouge.

Dynamic strain measurement using piezoelectric polymer film

Piezoelectric polymers have been used to form the basis of dynamic strain gauges for the detection of stress waves. The linearity of response was tested using a split Hopkinson pressure bar arrangement. The results obtained illustrate the effectiveness of piezoelectric film strain gauges in the measurement of axial stress waves.

A novel method for development of species and strain-specific DNA probes and PCR primers for identifying Burkholderia solanacearum (formerly Pseudomonas solanacearum)

Six Burkholderia solanacearum (formerly Pseudomonas solanacearum) genomic DNA fragments were isolated, using RAPD techniques and cloning, from the three genetically diverse strains: ACH092 (Biovar 4), ACH0158 (Biovar 2) and ACH0171 (Biovar 3) (1). One of these cloned fragments was selected because it was present constantly in all bacterial strains analysed. The remaining five clones were selected because Southern hybridisation revealed that each showed partial or complete specificity towards the strain of origin. A seventh genomic fragment showing a strain-specific distribution in Southern hybridisations was obtained by differential restriction, hybridisation and cloning of genomic DNA. Each of these clones was sequenced and primers to amplify the insert were designed. When DNA from the strain of origin was used as template, PCR amplification for each of these fragments yielded a single band on gel analysis. One pair of primers amplified the species-constant fragment of 281 bp from DNA of all B. solanacearum strains investigated, from DNA of the closely related bacterium which causes ''blood disease'' of banana (BDB) and in P. syzigii. The sensitivity of detection of B. solanacearum using these ubiquitous primers was between 1.3 and 20 bacterial cells. The feasibility and reliability of a PCR approach to detection and identification of B. solanacearum was tested in diverse strains of the bacterium in several countries and laboratories.

Increased tissue resistance in the nude mouse against Candida albicans without altering strain-dependent differences in susceptibility

Strain differences in tissue responses to infection with Candida albicans were examined in nude mice having susceptible (CBA/CaH) and resistant (BALB/c) parentage. Homozygous (nu/nu) mice of both strains were more resistant to systemic infection with C. albicans than heterozygous (nu/+) littermates as indicated by a reduction in both the severity of tissue damage and colony counts in the brain and kidney. However, the tissue lesions in nu/nu CBA/CaH mice were markedly more severe than those in nu/nu mice with the BALB/c background. This pattern was reflected in the greater fungal burden in the CBA/CaH strain. Analysis of cDNA from infected tissues using a competitive polymerase chain reaction excluded interferon-gamma (IFN-gamma), tumour necrosis factor-alpha (TNF-alpha), and interleukin 6 (IL-6) as mediators of the enhanced resistance of the nude mice. The results confirm that the different patterns of lesion severity in BALB/c and CBA/CaH mice do not involve T lymphocyte-mediated pathology, and are consistent with the hypothesis that strain-dependent tissue damage is not dependent on the effector function of macrophages or their precursors.

Quantification of Regional Left and Right Ventricular Deformation Indices in Healthy Neonates by Using Strain Rate and Strain Imaging

Background: Color Doppler myocardial imaging (CDMI) allows the calculation of local longitudinal or radial strain rate (SR) and strain (epsilon). The aims of this study were to determine the feasibility and reproducibility of longitudinal and radial SR and epsilon in neonates during the first hours of life and to establish reference values. Methods: Data were obtained from 55 healthy neonates (29 male; mean age, 20 +/- 14 hours; mean birth weight, 3,174 +/- 374 g). Apical and parasternal views quantified regional longitudinal and radial SR and epsilon in differing ventricular wall segments. Values at peak systole, early diastole, and late diastole were calculated from the extracted curves. CDMI data acquired at 300 +/- 50 frames/s were analyzed offline. Three consecutive cardiac cycles were measured during normal respiration. The timing of specific systolic or diastolic regional events was determined. Multiple comparisons between walls and segments were made. Results: Left ventricular (LV) longitudinal deformation showed basal differences compared with apical segments within one specific wall. Right ventricular (RV) longitudinal deformation was not homogeneous, with significant differences between basal and apical segments. Longitudinal 3 values were higher in the RV free basal and middle wall segments compared with the left ventricle. In the RV free wall apical segment, longitudinal SR and 3 were maximal. LV systolic SR and epsilon values were higher radially compared with longitudinally (radial peak systolic SR midportion, 2.9 +/- 0.6 s(-1); radial peak systolic epsilon 53.8 +/- 19%; longitudinal peak systolic SR midportion, -1.8 +/- 0.5 s(-1); longitudinal peak systolic epsilon, -24.8 +/- 3%; P < .01). Longitudinal systolic epsilon and SR interobserver variability values were 1.2% and 0.7%, respectively. Conclusion: Ultrasound-based SR and 3 imaging is a practical and reproducible clinical technique in neonates, allowing the calculation of regional longitudinal and radial deformation in RV and LV segments. These regional SR and epsilon indices represent new, noninvasive parameters that can quantify normal neonate regional cardiac function. Independent from visual interpretation, they can be used as reference values for diagnosis in ill neonates. (J Am Soc Echocardiogr 2009;22:369-375.)

The influence of collision energy and strain accumulation on the kinetics of mechanical alloying

The kinetics of mechanical alloying have been investigated by examining the effect that ball mass has on the rate at which titanium carbide forms from the elements. By varying the ball density while keeping the ball diameter and the charge ratio constant, the collision energy was independently controlled. Grinding media with a density from 3.8 g cm(-3) (agate) to 16.4 g cm(-3) (tungsten carbide) were used. The reaction rate increases exponentially with ball mass until a critical level is reached, which is determined by the induced temperature rise. Above this level, collisions of higher energy have no advantage. It is also shown that the reaction rate increases exponentially with the rate at which strain accumulates in the reactants. It is suggested that the strain accumulation rate in mechanically induced reactions is analogous to temperature in thermally induced chemical reactions.

Differences Between ""Classical"" Risk Factors for Infections Caused by Methicillin-Resistant Staphylococcus aureus (MRSA) and Risk Factors for Nosocomial Bloodstream Infections Caused by Multiple Clones of the Staphylococcal Cassette Chromosome mec Type IV MRSA Strain

OBJECTIVE. To identify risk factors associated with nosocomial bloodstream infections caused by multiple clones of the staphylococcal cassette chromosome mec (SCCmec) type IV strain of methicillin-resistant Staphylococcus aureus (MRSA). DESIGN. An unmatched case-control study (at a ratio of 1 : 2) performed during the period from October 2002 through September 2003. SETTING. A 2,000-bed tertiary care teaching hospital affiliated with the University of Sao Paulo in Sao Paulo, Brazil. METHODS. Case patients (n = 30) were defined either as patients who had a bloodstream infection due to SCCmec type IV strains of MRSA diagnosed at least 48 hours after hospital admission or as neonates with the infection who were born in the hospital. Control patients (n = 60) were defined as patients with SCCmec type III MRSA infection diagnosed at least 48 hours after hospital admission. Genes n = 60 encoding virulence factors were studied in the isolates recovered from case patients, and molecular typing of the SCCmec type IV MRSA isolates was also done by pulsed-field gel electrophoresis and multilocus sequence typing. RESULTS. In multivariate analysis, the following 3 variables were significantly associated with having a nosocomial bloodstream infection caused by SCCmec type IV strains of MRSA: an age of less than 1 year, less frequent use of a central venous catheter (odds ratio [OR], 0.07 [95% confidence interval {CI}, 0.02-0.28]; P = .001), and female sex. A second analysis was performed that excluded the case and Pp. 001 control patients from the neonatal unit, and, in multivariate analysis, the following variables were significantly associated with having a nosocomial bloodstream infection caused by SCCmec type IV strains of MRSA: less frequent use of a central venous catheter (OR, 0.12 [95% CI, 0.03-0.55]; P = .007), lower Acute Physiology and Chronic Health Evaluation II score on admission (OR, 0.14 [95% CI, 0.03-0.61];), less frequent surgery (OR, 0.21 [95% CI, 0.06-0.83];), and female sex (OR, 5.70 [95% CI, 1.32-24.66]; P =.020). P = .009 Pp. 025 Pp). Of the 29 SCCmec type IV MRSA isolates recovered from case patients, none contained the Panton-Valentine leukocidin, gamma-hemolysin, enterotoxin B or C, or toxic shock syndrome toxin-1. All of the isolates contained genes for the LukE-LukD leukocidin and alpha-hemolysin. Genes for enterotoxin A were present in 1 isolate, and genes for beta-hemolysin were present in 3 isolates. CONCLUSIONS. ""Classical"" risk factors do not apply to patients infected with the SCCmec type IV strain of MRSA, which is an important cause of nosocomial bacteremia. This strain infects a patient population that is less ill and has had less frequent invasive procedures than a patient population infected with the multidrug-resistant strain of SCCmec type III MRSA. We found that virulence factors were rare and that Panton-Valentine leukocidin was absent. There were multiple clones of the SCCmec type IV strain in our hospital. Children under 1 year of age were at a higher risk. There was a predominant clone ( sequence type 5) in this patient population.

Prone position prevents regional alveolar hyperinflation and mechanical stress and strain in mild experimental acute lung injury

Prone position may delay the development of ventilator-induced lung injury (VILI), but the mechanisms require better elucidation. In experimental mild acute lung injury (ALI), arterial oxygen partial pressure (Pa(O2)), lung mechanics and histology, inflammatory markers [interleukin (IL)-6 and IL-1 beta], and type III procollagen (PCIII) mRNA expressions were analysed in supine and prone position. Wistar rats were randomly divided into two groups. In controls, saline was intraperitoneally injected while ALI was induced by paraquat. After 24-h, the animals were mechanically ventilated for 1-h in supine or prone positions. In ALI, prone position led to a better blood flow/tissue ratio both in ventral and dorsal regions and was associated with a more homogeneous distribution of alveolar aeration/tissue ratio reducing lung static elastance and viscoelastic pressure, and increasing end-expiratory lung volume and Pa(O2). PCIII expression was higher in the ventral than dorsal region in supine position, with no regional changes in inflammatory markers. In conclusion, prone position may protect the lungs against VILI, thus reducing pulmonary stress and strain. (C) 2009 Elsevier B.V. All rights reserved.

PENILE AND SCROTUM SWELLING IN JUVENILE DERMATOMYOSITIS

Edema is a well-known feature of juvenile dermatomyositis (JDM). However, to our knowledge localized penile and scrotum swelling was not previously reported. During a 27-year period, 5,506 patients were followed up at the Pediatric Rheumatology Unit of our University Hospital and 157 patients (2.9%) had JDM. One of them (0.6%) had concomitant localized penile and scrotum swelling. He had severe disease activity since he was 7-year-old, manifested by diffuse cutaneous vasculitis, recurrent localized edema (limbs or face) and only one episode of generalized edema. At the age of 10, he presented edema of the genitalia associated with mild skin erythema. Penis, scrotum and testicular ultrasound as well as magnetic resonance imaging showed skin edema without testicular involvement. He was taking prednisone, methotrexate, cyclosporin, hydroxychloroquine and thalidomide. Improvement of skin rash, penile and scrotum swelling was noticed only with rituximab therapy. No adverse event was observed during anti-CD20 infusions and after six months of follow up. Penile and scrotum edema was a rare manifestation of JDM which improved with anti-CD20 monoclonal antibody treatment.