Dynamic modeling and analysis of single-stage boost inverters under normal and abnormal conditions

Inverters play key roles in connecting sustainable energy (SE) sources to the local loads and the ac grid. Although there has been a rapid expansion in the use of renewable sources in recent years, fundamental research, on the design of inverters that are specialized for use in these systems, is still needed. Recent advances in power electronics have led to proposing new topologies and switching patterns for single-stage power conversion, which are appropriate for SE sources and energy storage devices. The current source inverter (CSI) topology, along with a newly proposed switching pattern, is capable of converting the low dc voltage to the line ac in only one stage. Simple implementation and high reliability, together with the potential advantages of higher efficiency and lower cost, turns the so-called, single-stage boost inverter (SSBI), into a viable competitor to the existing SE-based power conversion technologies.^ The dynamic model is one of the most essential requirements for performance analysis and control design of any engineering system. Thus, in order to have satisfactory operation, it is necessary to derive a dynamic model for the SSBI system. However, because of the switching behavior and nonlinear elements involved, analysis of the SSBI is a complicated task.^ This research applies the state-space averaging technique to the SSBI to develop the state-space-averaged model of the SSBI under stand-alone and grid-connected modes of operation. Then, a small-signal model is derived by means of the perturbation and linearization method. An experimental hardware set-up, including a laboratory-scaled prototype SSBI, is built and the validity of the obtained models is verified through simulation and experiments. Finally, an eigenvalue sensitivity analysis is performed to investigate the stability and dynamic behavior of the SSBI system over a typical range of operation. ^

Negotiating social and moral order in internet relay chat

Although internet chat is a significant aspect of many internet users’ lives, the manner in which participants in quasi-synchronous chat situations orient to issues of social and moral order remains to be studied in depth. The research presented here is therefore at the forefront of a continually developing area of study. This work contributes new insights into how members construct and make accountable the social and moral orders of an adult-oriented Internet Relay Chat (IRC) channel by addressing three questions: (1) What conversational resources do participants use in addressing matters of social and moral order? (2) How are these conversational resources deployed within IRC interaction? and (3) What interactional work is locally accomplished through use of these resources? A survey of the literature reveals considerable research in the field of computer-mediated communication, exploring both asynchronous and quasi-synchronous discussion forums. The research discussed represents a range of communication interests including group and collaborative interaction, the linguistic construction of social identity, and the linguistic features of online interaction. It is suggested that the present research differs from previous studies in three ways: (1) it focuses on the interaction itself, rather than the ways in which the medium affects the interaction; (2) it offers turn-by-turn analysis of interaction in situ; and (3) it discusses membership categories only insofar as they are shown to be relevant by participants through their talk. Through consideration of the literature, the present study is firmly situated within the broader computer-mediated communication field. Ethnomethodology, conversation analysis and membership categorization analysis were adopted as appropriate methodological approaches to explore the research focus on interaction in situ, and in particular to investigate the ways in which participants negotiate and co-construct social and moral orders in the course of their interaction. IRC logs collected from one chat room were analysed using a two-pass method, based on a modification of the approaches proposed by Pomerantz and Fehr (1997) and ten Have (1999). From this detailed examination of the data corpus three interaction topics are identified by means of which participants clearly orient to issues of social and moral order: challenges to rule violations, ‘trolling’ for cybersex, and experiences regarding the 9/11 attacks. Instances of these interactional topics are subjected to fine-grained analysis, to demonstrate the ways in which participants draw upon various interactional resources in their negotiation and construction of channel social and moral orders. While these analytical topics stand alone in individual focus, together they illustrate different instances in which participants’ talk serves to negotiate social and moral orders or collaboratively construct new orders. Building on the work of Vallis (2001), Chapter 5 illustrates three ways that rule violation is initiated as a channel discussion topic: (1) through a visible violation in open channel, (2) through an official warning or sanction by a channel operator regarding the violation, and (3) through a complaint or announcement of a rule violation by a non-channel operator participant. Once the topic has been initiated, it is shown to become available as a topic for others, including the perceived violator. The fine-grained analysis of challenges to rule violations ultimately demonstrates that channel participants orient to the rules as a resource in developing categorizations of both the rule violation and violator. These categorizations are contextual in that they are locally based and understood within specific contexts and practices. Thus, it is shown that compliance with rules and an orientation to rule violations as inappropriate within the social and moral orders of the channel serves two purposes: (1) to orient the speaker as a group member, and (2) to reinforce the social and moral orders of the group. Chapter 6 explores a particular type of rule violation, solicitations for ‘cybersex’ known in IRC parlance as ‘trolling’. In responding to trolling violations participants are demonstrated to use affiliative and aggressive humour, in particular irony, sarcasm and insults. These conversational resources perform solidarity building within the group, positioning non-Troll respondents as compliant group members. This solidarity work is shown to have three outcomes: (1) consensus building, (2) collaborative construction of group membership, and (3) the continued construction and negotiation of existing social and moral orders. Chapter 7, the final data analysis chapter, offers insight into how participants, in discussing the events of 9/11 on the actual day, collaboratively constructed new social and moral orders, while orienting to issues of appropriate and reasonable emotional responses. This analysis demonstrates how participants go about ‘doing being ordinary’ (Sacks, 1992b) in formulating their ‘first thoughts’ (Jefferson, 2004). Through sharing their initial impressions of the event, participants perform support work within the interaction, in essence working to normalize both the event and their initial misinterpretation of it. Normalising as a support work mechanism is also shown in relation to participants constructing the ‘quiet’ following the event as unusual. Normalising is accomplished by reference to the indexical ‘it’ and location formulations, which participants use both to negotiate who can claim to experience the ‘unnatural quiet’ and to identify the extent of the quiet. Through their talk participants upgrade the quiet from something legitimately experienced by one person in a particular place to something that could be experienced ‘anywhere’, moving the phenomenon from local to global provenance. With its methodological design and detailed analysis and findings, this research contributes to existing knowledge in four ways. First, it shows how rules are used by participants as a resource in negotiating and constructing social and moral orders. Second, it demonstrates that irony, sarcasm and insults are three devices of humour which can be used to perform solidarity work and reinforce existing social and moral orders. Third, it demonstrates how new social and moral orders are collaboratively constructed in relation to extraordinary events, which serve to frame the event and evoke reasonable responses for participants. And last, the detailed analysis and findings further support the use of conversation analysis and membership categorization as valuable methods for approaching quasi-synchronous computer-mediated communication.

Web-based public participatory GIS

Decision support systems (DSS) have evolved rapidly during the last decade from stand alone or limited networked solutions to online participatory solutions. One of the major enablers of this change is the fastest growing areas of geographical information system (GIS) technology development that relates to the use of the Internet as a means to access, display, and analyze geospatial data remotely. World-wide many federal, state, and particularly local governments are designing to facilitate data sharing using interactive Internet map servers. This new generation DSS or planning support systems (PSS), interactive Internet map server, is the solution for delivering dynamic maps and GIS data and services via the world-wide Web, and providing public participatory GIS (PPGIS) opportunities to a wider community (Carver, 2001; Jankowski & Nyerges, 2001). It provides a highly scalable framework for GIS Web publishing, Web-based public participatory GIS (WPPGIS), which meets the needs of corporate intranets and demands of worldwide Internet access (Craig, 2002). The establishment of WPPGIS provides spatial data access through a support centre or a GIS portal to facilitate efficient access to and sharing of related geospatial data (Yigitcanlar, Baum, & Stimson, 2003). As more and more public and private entities adopt WPPGIS technology, the importance and complexity of facilitating geospatial data sharing is growing rapidly (Carver, 2003). Therefore, this article focuses on the online public participation dimension of the GIS technology. The article provides an overview of recent literature on GIS and WPPGIS, and includes a discussion on the potential use of these technologies in providing a democratic platform for the public in decision-making.

Mailed treatment to augment primary care for alcohol disorders : a randomised controlled trial

Introduction and Aims: Remote delivery of interventions is needed to address large numbers of people with alcohol use disorders who are spread over large areas. Previous correspondence trials typically examined its effects as stand-alone treatment. This study aimed to test whether adding postal treatment to general practitioner (GP) support would lower alcohol use more than GP intervention alone. Design and Methods: A single-blind, randomised controlled trial with a crossover design was conducted over 12 months on 204 people with alcohol use disorders. Participants in an immediate correspondence condition received treatment over the first 3 months; those receiving delayed treatment received it in months 3–6. Results: Few participants were referred from GPs, and little intervention was offered by them. At 3 months, 78% of participants remained in the study. Those in immediate treatment showed greater reductions in alcohol per week, drinking days, anxiety, depression and distress than those in the delayed condition. However, post-treatment and follow-up outcomes still showed elevated alcohol use, depression, anxiety and distress. Greater baseline anxiety predicted better alcohol outcomes, although more mental distress at baseline predicted dropout. Discussion and Conclusions: The study gave consistent results with those from previous research on correspondence treatments, and showed that high levels of participant engagement over 3 months can be obtained. Substantial reductions in alcohol use are seen, with indications that they are well maintained. However, many participants continue to show high-risk alcohol use and psychological distress.

Designing for engagement : building IT systems

Context The School of Information Technology at QUT has recently undertaken a major restructuring of their Bachelor of Information Technology (BIT) course. Some of the aims of this restructuring include a reduction in first year attrition and to provide an attractive degree course that meets both student and industry expectations. Emphasis has been placed on the first semester in the context of retaining students by introducing a set of four units that complement one another and provide introductory material on technology, programming and related skills, and generic skills that will aid the students throughout their undergraduate course and in their careers. This discussion relates to one of these four fist semester units, namely Building IT Systems. The aim of this unit is to create small Information Technology (IT) systems that use programming or scripting, databases as either standalone applications or web applications. In the prior history of teaching introductory computer programming at QUT, programming has been taught as a stand alone subject and integration of computer applications with other systems such as databases and networks was not undertaken until students had been given a thorough grounding in those topics as well. Feedback has indicated that students do not believe that working with a database requires programming skills. In fact, the teaching of the building blocks of computer applications have been compartmentalized and taught in isolation from each other. The teaching of introductory computer programming has been an industry requirement of IT degree courses as many jobs require at least some knowledge of the topic. Yet, computer programming is not a skill that all students have equal capabilities of learning (Bruce et al., 2004) and this is clearly shown by the volume of publications dedicated to this topic in the literature over a broad period of time (Eckerdal & Berglund, 2005; Mayer, 1981; Winslow, 1996). The teaching of this introductory material has been done pretty much the same way over the past thirty years. During this period of time that introductory computer programming courses have been taught at QUT, a number of different programming languages and programming paradigms have been used and different approaches to teaching and learning have been attempted in an effort to find the golden thread that would allow students to learn this complex topic. Unfortunately, computer programming is not a skill that can be learnt in one semester. Some basics can be learnt but it can take many years to master (Norvig, 2001). Faculty data typically has shown a bimodal distribution of results for students undertaking introductory programming courses with a high proportion of students receiving a high mark and a high proportion of students receiving a low or failing mark. This indicates that there are students who understand and excel with the introductory material while there is another group who struggle to understand the concepts and practices required to be able to translate a specification or problem statement into a computer program that achieves what is being requested. The consequence of a large group of students failing the introductory programming course has been a high level of attrition amongst first year students. This attrition level does not provide good continuity in student numbers in later years of the degree program and the current approach is not seen as sustainable.

Australia : LIS education

The topic of library and information science (LIS) education has been under the spotlight in the professional literature in Australia and New Zealand for a number of years. Critical issues of discussion encompass the apparent lack of a core curriculum for the discipline, the perceived gulf between LIS education and LIS practice, and the pressing need for career-long learning and development. One of the central points of debate that emerges repeatedly is the long-standing question about the positioning of the profession: Is LIS a graduate profession of highly skilled individuals valued for their expertise and professionalism or is it a profession of anyone who works in a library, regardless of their qualifications (LIANZA, 2005)? While Australia and New Zealand do not stand alone in this debate – similar issues are echoed in many other countries – there are inevitably some local characteristics which warrant exploration. The discussion presented here highlights the historical background to professional training, the specific professional policies and standards that guide LIS education and some of the challenges facing professional and paraprofessional education, given the changing environment of education in Australia as a whole, with some comparisons made with the New Zealand situation. While all too often library practitioners point the finger at the library educators to ‘right the wrongs’, the authors wish to reinforce the idea that the future of effective and relevant LIS education is a matter for all stakeholders in the profession: practitioners and educators, students and staff, employers and employees, with cohesion potentially offered by the professional body.

Re-thinking pedagogy for middle school students with little, no or severely interrupted schooling

The arrival of substantial cohorts of English language learners from Africa with little, no or severely interrupted schooling is requiring new pedagogic responses from teachers in Australia and other Western countries of refugee re-settlement. If the students are to have optimal educational and life chances, it is crucial for them to acquire resources for conceptually deep and critical literacy tasks while still learning basic reading and writing skills. This requires teachers to extend their pedagogic repertoires: subject area teachers must teach language and literacy alongside content; high school teachers must teach what has been thought of as primary school curriculum. The aim of this article is to describe some teacher responses to these challenges. Data are drawn from a study involving an intensive language school and three high schools, and also from the author’s experience as a homework tutor for refugees. Stand-alone basic skills programs are described, as are modifications of long-established ESL programs. It is also argued that teachers need to find ways of linking with the conceptual knowledge of students who arrive with content area backgrounds different from others in their class. Everyday life experiences prior to, and after re-settlement in the West, are rich with potential in this regard.

Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Image acquisition and manipulation protocols for CT-PET fusion to improve the accuracy of gross tumour volume localisation for 3D conformal radiotherapy for lung cancer

Aims: To develop clinical protocols for acquiring PET images, performing CT-PET registration and tumour volume definition based on the PET image data, for radiotherapy for lung cancer patients and then to test these protocols with respect to levels of accuracy and reproducibility. Method: A phantom-based quality assurance study of the processes associated with using registered CT and PET scans for tumour volume definition was conducted to: (1) investigate image acquisition and manipulation techniques for registering and contouring CT and PET images in a radiotherapy treatment planning system, and (2) determine technology-based errors in the registration and contouring processes. The outcomes of the phantom image based quality assurance study were used to determine clinical protocols. Protocols were developed for (1) acquiring patient PET image data for incorporation into the 3DCRT process, particularly for ensuring that the patient is positioned in their treatment position; (2) CT-PET image registration techniques and (3) GTV definition using the PET image data. The developed clinical protocols were tested using retrospective clinical trials to assess levels of inter-user variability which may be attributed to the use of these protocols. A Siemens Somatom Open Sensation 20 slice CT scanner and a Philips Allegro stand-alone PET scanner were used to acquire the images for this research. The Philips Pinnacle3 treatment planning system was used to perform the image registration and contouring of the CT and PET images. Results: Both the attenuation-corrected and transmission images obtained from standard whole-body PET staging clinical scanning protocols were acquired and imported into the treatment planning system for the phantom-based quality assurance study. Protocols for manipulating the PET images in the treatment planning system, particularly for quantifying uptake in volumes of interest and window levels for accurate geometric visualisation were determined. The automatic registration algorithms were found to have sub-voxel levels of accuracy, with transmission scan-based CT-PET registration more accurate than emission scan-based registration of the phantom images. Respiration induced image artifacts were not found to influence registration accuracy while inadequate pre-registration over-lap of the CT and PET images was found to result in large registration errors. A threshold value based on a percentage of the maximum uptake within a volume of interest was found to accurately contour the different features of the phantom despite the lower spatial resolution of the PET images. Appropriate selection of the threshold value is dependant on target-to-background ratios and the presence of respiratory motion. The results from the phantom-based study were used to design, implement and test clinical CT-PET fusion protocols. The patient PET image acquisition protocols enabled patients to be successfully identified and positioned in their radiotherapy treatment position during the acquisition of their whole-body PET staging scan. While automatic registration techniques were found to reduce inter-user variation compared to manual techniques, there was no significant difference in the registration outcomes for transmission or emission scan-based registration of the patient images, using the protocol. Tumour volumes contoured on registered patient CT-PET images using the tested threshold values and viewing windows determined from the phantom study, demonstrated less inter-user variation for the primary tumour volume contours than those contoured using only the patient’s planning CT scans. Conclusions: The developed clinical protocols allow a patient’s whole-body PET staging scan to be incorporated, manipulated and quantified in the treatment planning process to improve the accuracy of gross tumour volume localisation in 3D conformal radiotherapy for lung cancer. Image registration protocols which factor in potential software-based errors combined with adequate user training are recommended to increase the accuracy and reproducibility of registration outcomes. A semi-automated adaptive threshold contouring technique incorporating a PET windowing protocol, accurately defines the geometric edge of a tumour volume using PET image data from a stand alone PET scanner, including 4D target volumes.

Fear and danger in nocturnal urban environments

At the centre of this research is an ethnographic study that saw the researcher embedded within the fabric of inner city life to better understand what characteristics of user activity and interaction could be enhanced by technology. The initial research indicated that the experience of traversing the city after dark unified an otherwise divergent user group through a shared concern for personal safety. Managing this fear and danger represented an important user need. We found that mobile social networking systems are not only integral for bringing people together, they can help in the process of users safely dispersing as well. We conclude, however, that at a time when the average iPhone staggers under the weight of a plethora of apps that do everything from acting as a carpenter’s level to a pregnancy predictor, we consider the potential for the functionality of a personal safety device to be embodied within a stand alone artifact.

3D visualisation of groundwater/surface water systems as a planning and communication tool

Groundwater is increasingly recognised as an important yet vulnerable natural resource, and a key consideration in water cycle management. However, communication of sub-surface water system behaviour, as an important part of encouraging better water management, is visually difficult. Modern 3D visualisation techniques can be used to effectively communicate these complex behaviours to engage and inform community stakeholders. Most software developed for this purpose is expensive and requires specialist skills. The Groundwater Visualisation System (GVS) developed by QUT integrates a wide range of surface and sub-surface data, to produce a 3D visualisation of the behaviour, structure and connectivity of groundwater/surface water systems. Surface data (elevation, surface water, land use, vegetation and geology) and data collected from boreholes (bore locations and subsurface geology) are combined to visualise the nature, structure and connectivity of groundwater/surface water systems. Time-series data (water levels, groundwater quality, rainfall, stream flow and groundwater abstraction) is displayed as an animation within the 3D framework, or graphically, to show water system condition changes over time. GVS delivers an interactive, stand-alone 3D Visualisation product that can be used in a standard PC environment. No specialised training or modelling skills are required. The software has been used extensively in the SEQ region to inform and engage both water managers and the community alike. Examples will be given of GVS visualisations developed in areas where there have been community concerns around groundwater over-use and contamination.

Community engagement and groundwater investigation in a rural/peri urban basaltic aquifier system, Tamborine Mountain, South East Queensland

The Tamborine Mt area is a popular residential and tourist area in the Gold Coast hinterland, SE Qld. The 15km2 area occurs on elevated remnant Tertiary Basalts of the Beechmont Group, which comprise a number of mappable flow units originally derived from the Tweed volcanic centre to the south. The older Albert Basalt (Tertiary), which underlies the Beechmont Basalt at the southern end of the investigation area, is thought to be derived from the Focal Peak volcanic centre to the south west. The Basalts contain a locally significant ‘un-declared’ groundwater resource, which is utilised by the Tamborine Mt community for: • domestic purposes to supplement rainwater tank supplies, • commercial scale horticulture and • commercial export off-Mountain for bottled water. There is no reticulated water supply, and all waste water is treated on-site through domestic scale WTPs. Rainforest and other riparian ecosystems that attract residents and tourist dollars to the area, are also reliant on the groundwater that discharges to springs and surface streams on and around the plateau. Issues regarding a lack of compiled groundwater information, groundwater contamination, and groundwater sustainability are being investigated by QUT, utilising funding provided by the Federal Government’s ‘Caring for our Country’ programme through SEQ Catchments Ltd. The objectives of the two year project, which started in April 2009, are to: • Characterise the nature and condition of groundwater / surface water systems in the Tamborine Mountain area in terms of the issues being raised; • Engage and build capacity within the community to source local knowledge, encourage participation, raise awareness and improve understanding of the impacts of land and water use; • Develop a stand-alone 3D Visualisation model for dissemination into the community and use as a communication tool.

Fusing curricula : science, technology and ICT

Curriculum demands continue to increase on school education systems with teachers at the forefront of implementing syllabus requirements. Education is reported frequently as a solution to most societal problems and, as a result of the world’s information explosion, teachers are expected to cover more and more within teaching programs. How can teachers combine subjects in order to capitalise on the competing educational agendas within school timeframes? Fusing curricula requires the bonding of standards from two or more syllabuses. Both technology and ICT complement the learning of science. This study analyses selected examples of preservice teachers’ overviews for fusing science, technology and ICT. These program overviews focused on primary students and the achievement of two standards (one from science and one from either technology or ICT). These primary preservice teachers’ fused-curricula overviews included scientific concepts and related technology and/or ICT skills and knowledge. Findings indicated a range of innovative curriculum plans for teaching primary science through technology and ICT, demonstrating that these subjects can form cohesive links towards achieving the respective learning standards. Teachers can work more astutely by fusing curricula; however further professional development may be required to advance thinking about these processes. Bonding subjects through their learning standards can extend beyond previous integration or thematic work where standards may not have been assessed. Education systems need to articulate through syllabus documents how effective fusing of curricula can be achieved. It appears that education is a key avenue for addressing societal needs, problems and issues. Education is promoted as a universal solution, which has resulted in curriculum overload (Dare, Durand, Moeller, & Washington, 1997; Vinson, 2001). Societal and curriculum demands have placed added pressure on teachers with many extenuating education issues increasing teachers’ workloads (Mobilise for Public Education, 2002). For example, as Australia has weather conducive for outdoor activities, social problems and issues arise that are reported through the media calling for action; consequently schools have been involved in swimming programs, road and bicycle safety programs, and a wide range of activities that had been considered a parental responsibility in the past. Teachers are expected to plan, implement and assess these extra-curricula activities within their already overcrowded timetables. At the same stage, key learning areas (KLAs) such as science and technology are mandatory requirements within all Australian education systems. These systems have syllabuses outlining levels of content and the anticipated learning outcomes (also known as standards, essential learnings, and frameworks). Time allocated for teaching science in obviously an issue. In 2001, it was estimated that on average the time spent in teaching science in Australian Primary Schools was almost an hour per week (Goodrum, Hackling, & Rennie, 2001). More recently, a study undertaken in the U.S. reported a similar finding. More than 80% of the teachers in K-5 classrooms spent less than an hour teaching science (Dorph, Goldstein, Lee, et al., 2007). More importantly, 16% did not spend teaching science in their classrooms. Teachers need to learn to work smarter by optimising the use of their in-class time. Integration is proposed as one of the ways to address the issue of curriculum overload (Venville & Dawson, 2005; Vogler, 2003). Even though there may be a lack of definition for integration (Hurley, 2001), curriculum integration aims at covering key concepts in two or more subject areas within the same lesson (Buxton & Whatley, 2002). This implies covering the curriculum in less time than if the subjects were taught separately; therefore teachers should have more time to cover other educational issues. Expectedly, the reality can be decidedly different (e.g., Brophy & Alleman, 1991; Venville & Dawson, 2005). Nevertheless, teachers report that students expand their knowledge and skills as a result of subject integration (James, Lamb, Householder, & Bailey, 2000). There seems to be considerable value for integrating science with other KLAs besides aiming to address teaching workloads. Over two decades ago, Cohen and Staley (1982) claimed that integration can bring a subject into the primary curriculum that may be otherwise left out. Integrating science education aims to develop a more holistic perspective. Indeed, life is not neat components of stand-alone subjects; life integrates subject content in numerous ways, and curriculum integration can assist students to make these real-life connections (Burnett & Wichman, 1997). Science integration can provide the scope for real-life learning and the possibility of targeting students’ learning styles more effectively by providing more than one perspective (Hudson & Hudson, 2001). To illustrate, technology is essential to science education (Blueford & Rosenbloom, 2003; Board of Studies, 1999; Penick, 2002), and constructing technology immediately evokes a social purpose for such construction (Marker, 1992). For example, building a model windmill requires science and technology (Zubrowski, 2002) but has a key focus on sustainability and the social sciences. Science has the potential to be integrated with all KLAs (e.g., Cohen & Staley, 1982; Dobbs, 1995; James et al., 2000). Yet, “integration” appears to be a confusing term. Integration has an educational meaning focused on special education students being assimilated into mainstream classrooms. The word integration was used in the late seventies and generally focused around thematic approaches for teaching. For instance, a science theme about flight only has to have a student drawing a picture of plane to show integration; it did not connect the anticipated outcomes from science and art. The term “fusing curricula” presents a seamless bonding between two subjects; hence standards (or outcomes) need to be linked from both subjects. This also goes beyond just embedding one subject within another. Embedding implies that one subject is dominant, while fusing curricula proposes an equal mix of learning within both subject areas. Primary education in Queensland has eight KLAs, each with its established content and each with a proposed structure for levels of learning. Primary teachers attempt to cover these syllabus requirements across the eight KLAs in less than five hours a day, and between many of the extra-curricula activities occurring throughout a school year (e.g., Easter activities, Education Week, concerts, excursions, performances). In Australia, education systems have developed standards for all KLAs (e.g., Education Queensland, NSW Department of Education and Training, Victorian Education) usually designated by a code. In the late 1990’s (in Queensland), “core learning outcomes” for strands across all KLA’s. For example, LL2.1 for the Queensland Education science syllabus means Life and Living at Level 2 standard number 1. Thus, a teacher’s planning requires the inclusion of standards as indicated by the presiding syllabus. More recently, the core learning outcomes were replaced by “essential learnings”. They specify “what students should be taught and what is important for students to have opportunities to know, understand and be able to do” (Queensland Studies Authority, 2009, para. 1). Fusing science education with other KLAs may facilitate more efficient use of time and resources; however this type of planning needs to combine standards from two syllabuses. To further assist in facilitating sound pedagogical practices, there are models proposed for learning science, technology and other KLAs such as Bloom’s Taxonomy (Bloom, 1956), Productive Pedagogies (Education Queensland, 2004), de Bono’s Six Hats (de Bono, 1985), and Gardner’s Multiple Intelligences (Gardner, 1999) that imply, warrant, or necessitate fused curricula. Bybee’s 5 Es, for example, has five levels of learning (engage, explore, explain, elaborate, and evaluate; Bybee, 1997) can have the potential for fusing science and ICT standards.

New media services : ratings and recommendations websites in the travel and tourism industry

The travel and hospitality industry is one which relies especially crucially on word of mouth, both at the level of overall destinations (Australia, Queensland, Brisbane) and at the level of travellers’ individual choices of hotels, restaurants, sights during their trips. The provision of such word-of-mouth information has been revolutionised over the past decade by the rise of community-based Websites which allow their users to share information about their past and future trips and advise one another on what to do or what to avoid during their travels. Indeed, the impact of such user-generated reviews, ratings, and recommendations sites has been such that established commercial travel advisory publishers such as Lonely Planet have experienced a pronounced downturn in sales ¬– unless they have managed to develop their own ways of incorporating user feedback and contributions into their publications. This report examines the overall significance of ratings and recommendation sites to the travel industry, and explores the community, structural, and business models of a selection of relevant ratings and recommendations sites. We identify a range of approaches which are appropriate to the respective target markets and business aims of these organisations, and conclude that there remain significant opportunities for further operators especially if they aim to cater for communities which are not yet appropriately served by specific existing sites. Additionally, we also point to the increasing importance of connecting stand-alone ratings and recommendations sites with general social media spaces like Facebook, Twitter, and LinkedIn, and of providing mobile interfaces which enable users to provide updates and ratings directly from the locations they happen to be visiting. In this report, we profile the following sites: * TripAdvisor, the international market leader for travel ratings and recommendations sites, with a membership of some 11 million users; * IgoUgo, the other leading site in this field, which aims to distinguish itself from the market leader by emphasising the quality of its content; * Zagat, a long-established publisher of restaurant guides which has translated its crowdsourcing model from the offline to the online world; * Lonely Planet’s Thorn Tree site, which attempts to respond to the rise of these travel communities by similarly harnessing user-generated content; * Stayz, which attempts to enhance its accommodation search and booking services by incorporating ratings and reviews functionality; and * BigVillage, an Australian-based site attempting to cater for a particularly discerning niche of travellers; * Dopplr, which connects travel and social networking in a bid to pursue the lucrative market of frequent and business travellers; * Foursquare, which builds on its mobile application to generate a steady stream of ‘check-ins’ and recommendations for hospitality and other services around the world; * Suite 101, which uses a revenue-sharing model to encourage freelance writers to contribute travel writing (amongst other genres of writing); * Yelp, the global leader in general user-generated product review and recommendation services. In combination, these profiles provide an overview of current developments in the travel ratings and recommendations space (and beyond), and offer an outlook for further possibilities. While no doubt affected by the global financial downturn and the reduction in travel that it has caused, travel ratings and recommendations remain important – perhaps even more so if a reduction in disposable income has resulted in consumers becoming more critical and discerning. The aggregated word of mouth from many tens of thousands of travellers which these sites provide certainly has a substantial influence on their users. Using these sites to research travel options has now become an activity which has spread well beyond the digirati. The same is true also for many other consumer industries, especially where there is a significant variety of different products available – and so, this report may also be read as a case study whose findings are able to be translated, mutatis mutandis, to purchasing decisions from household goods through consumer electronics to automobiles.

Microscopic modelling of freeway operations

Freeways are divided roadways designed to facilitate the uninterrupted movement of motor vehicles. However, many freeways now experience demand flows in excess of capacity, leading to recurrent congestion. The Highway Capacity Manual (TRB, 1994) uses empirical macroscopic relationships between speed, flow and density to quantify freeway operations and performance. Capacity may be predicted as the maximum uncongested flow achievable. Although they are effective tools for design and analysis, macroscopic models lack an understanding of the nature of processes taking place in the system. Szwed and Smith (1972, 1974) and Makigami and Matsuo (1990) have shown that microscopic modelling is also applicable to freeway operations. Such models facilitate an understanding of the processes whilst providing for the assessment of performance, through measures of capacity and delay. However, these models are limited to only a few circumstances. The aim of this study was to produce more comprehensive and practical microscopic models. These models were required to accurately portray the mechanisms of freeway operations at the specific locations under consideration. The models needed to be able to be calibrated using data acquired at these locations. The output of the models needed to be able to be validated with data acquired at these sites. Therefore, the outputs should be truly descriptive of the performance of the facility. A theoretical basis needed to underlie the form of these models, rather than empiricism, which is the case for the macroscopic models currently used. And the models needed to be adaptable to variable operating conditions, so that they may be applied, where possible, to other similar systems and facilities. It was not possible to produce a stand-alone model which is applicable to all facilities and locations, in this single study, however the scene has been set for the application of the models to a much broader range of operating conditions. Opportunities for further development of the models were identified, and procedures provided for the calibration and validation of the models to a wide range of conditions. The models developed, do however, have limitations in their applicability. Only uncongested operations were studied and represented. Driver behaviour in Brisbane was applied to the models. Different mechanisms are likely in other locations due to variability in road rules and driving cultures. Not all manoeuvres evident were modelled. Some unusual manoeuvres were considered unwarranted to model. However the models developed contain the principal processes of freeway operations, merging and lane changing. Gap acceptance theory was applied to these critical operations to assess freeway performance. Gap acceptance theory was found to be applicable to merging, however the major stream, the kerb lane traffic, exercises only a limited priority over the minor stream, the on-ramp traffic. Theory was established to account for this activity. Kerb lane drivers were also found to change to the median lane where possible, to assist coincident mergers. The net limited priority model accounts for this by predicting a reduced major stream flow rate, which excludes lane changers. Cowan's M3 model as calibrated for both streams. On-ramp and total upstream flow are required as input. Relationships between proportion of headways greater than 1 s and flow differed for on-ramps where traffic leaves signalised intersections and unsignalised intersections. Constant departure onramp metering was also modelled. Minimum follow-on times of 1 to 1.2 s were calibrated. Critical gaps were shown to lie between the minimum follow-on time, and the sum of the minimum follow-on time and the 1 s minimum headway. Limited priority capacity and other boundary relationships were established by Troutbeck (1995). The minimum average minor stream delay and corresponding proportion of drivers delayed were quantified theoretically in this study. A simulation model was constructed to predict intermediate minor and major stream delays across all minor and major stream flows. Pseudo-empirical relationships were established to predict average delays. Major stream average delays are limited to 0.5 s, insignificant compared with minor stream delay, which reach infinity at capacity. Minor stream delays were shown to be less when unsignalised intersections are located upstream of on-ramps than signalised intersections, and less still when ramp metering is installed. Smaller delays correspond to improved merge area performance. A more tangible performance measure, the distribution of distances required to merge, was established by including design speeds. This distribution can be measured to validate the model. Merging probabilities can be predicted for given taper lengths, a most useful performance measure. This model was also shown to be applicable to lane changing. Tolerable limits to merging probabilities require calibration. From these, practical capacities can be estimated. Further calibration is required of traffic inputs, critical gap and minimum follow-on time, for both merging and lane changing. A general relationship to predict proportion of drivers delayed requires development. These models can then be used to complement existing macroscopic models to assess performance, and provide further insight into the nature of operations.