Investigation on Depth of Heat Affected Zone of Discharge Spot by High Repetitive Rate YAG Laser-Induced Discharge Texturing

It is known that the press formability and the elongation of laser textured sheet are improved, and the service life of textured roll is longer than that of the un-textured roll due to hardening of the treated surface. One of the goals to develop high repetitive rate YAG laser-induced discharge texturing (LIDT) is to get deeper hardening zone. By observing and measuring cross-section of LIDT spots in different discharge conditions, it is found that the single-crater, which is formed by the discharge conditions of anode, which is covered by an oil film and with rectangular current waveform, has the most depth of heat affected zone (HAZ) comparing with other crater shapes when discharge energy is the same. The depth of HAZ is mainly depends on pulse duration when the discharge spot is single-crater. The results are analyzed.

Hot spot formation outside of the fusion-fuel core

An alternative fast-ignition method is proposed involving the formation of a hot spot outside the precompressed fusion-fuel core by a series of shocks driven directly by the light pressure of laser pulses of increasing intensities. It is shown that a hot spot, which can be of different material from that of the fuel core, with temperature similar to 10 keV and density similar to 200 g/cm(2), can be formed. Being an electrically neutral plasma, the hot spot can easily be sent into the fuel core. (c) 2005 American Institute of Physics.

Characterization of a multi-keV x-ray source produced by nanosecond laser irradiation of a solid target: The influence of laser focus spot and target thickness

The influence of focus spot and target thickness on multi-keV x-ray sources generated by 2 ns duration laser heated solid targets are investigated on the Shenguang II laser facility. In the case of thick-foil targets, the experimental data and theoretical analysis show that the emission volume of the x-ray sources is sensitive to the laser focus spot and proportional to the 3 power of the focus spot size. The steady x-ray flux is proportional to the 5/3 power of the focus spot size of the given laser beam in our experimental condition. In the case of thin-foil targets, experimental data show that there is an optimal foil thickness corresponding to the given laser parameters. With the given laser beam, the optimal thin-foil thickness is proportional to the -2/3 power of the focus spot size, and the optimal x-ray energy of thin foil is independent of focus spot size. (C) 2008 American Institute of Physics.

Effect of laser spot size on fusion neutron yield in laser-deuterium cluster interactions

The effect of the laser spot size on the neutron yield of table-top nuclear fusion from explosions of a femtosecond intense laser pulse heated deuterium clusters is investigated by using a simplified model, in which the cluster size distribution and the energy attenuation of the laser as it propagates through the cluster jet are taken into account. It has been found that there exists a proper laser spot size for the maximum fusion neutron yield for a given laser pulse and a specific deuterium gas cluster jet. The proper spot size, which is dependent on the laser parameters and the cluster jet parameters, has been calculated and compared with the available experimental data. A reasonable agreement between the calculated results and the published experimental results is found.

Análisis del mercado eléctrico EPEX SPOT (Austria, Alemania, Suiza, Francia)

El objetivo de este trabajo es analizar el mercado EPEX Spot, con el fin de ver si mediante la integración de mercados se consigue converger los precios de la electricidad de Francia, Alemania, Suiza y Austria. En primer lugar se hará una breve descripción del proceso de liberalización llevado a cabo por los países que forman este mercado. A continuación, se introducirá EPEX Spot explicando el funcionamiento y los tipos de mercados que contiene. En la tercera sección se definirá el proceso de la armonización del mercado europeo. Por último, se hará un análisis más exhaustivo de la estructura de mercado de cada país y se examinará la evolución de los precios.

Far-field spot compression without energy loss in main lob in wireless laser communication

Far-field spot compression without energy loss in main lob is of great significance to wireless laser communication. In this letter, we propose two schemes to obtain far-field spot compression without energy loss in main lob. One scheme is based on the simulated annealing (SA) algorithm. Using SA algorithm, we design the phase profile of the diffractive phase element (DPE). Using the designed DPE, far-field spot compression without energy loss in main lob is achieved. The other scheme is based on YG algorithm. By means of YG algorithm, we appropriately designed the DPE in the emitting plane. Using the DPE, far-field spot compression without energy loss in main lob is obtained. (c) 2007 Elsevier GmbH. All rights reserved.

White spot syndrome virus (WSSV) transmission risk through infected cooked shrimp products assessed by polymerase chain reaction (PCR) and bio-inoculation studies

The aim of the study was to evaluate the resistance of white spot syndrome virus (WSSV) in shrimps (Penaeus monodon) to the process of cooking. The cooking was carried out at 1000C six different durations 5, 10, 15, 20, 25 and 30 min. The presence of WSSV was tested by single step and nested polymerase chain reaction (PCR). In the single step PCR, the primers 1s5 & 1a16 and IK1 & IK2 were used. While in the nested PCR, primers IK1 &IK2 – IK3 & IK4 were used for the detection of WSSV. WSSV was detected in the single step PCR with the primers 1s5 and 1a16 and the nested PCR with the primers IK1 and IK2 – IK3 & IK4 from the cooked shrimp samples. The cooked shrimps, which gave positive results for WSSV by PCR, were further confirmed for the viability of WSSV by conducting the bio-inoculation studies. Mortality (100%) was observed within 123 h of intra-muscular post injection (P.I) into the live healthy WSSV-free shrimps (P. monodon). These results show that the WSSV survive the cooking process and even infected cooked shrimp products may pose a transmission risk for WSSV to the native shrimp farming systems.

White spot viral disease in penaeid shrimp: a review

The white spot viral disease in penaeid shrimp affects the development of the global shrimp industry. This paper reviews the viruses that cause the disease, the transmission of the virus, diagnosis and preventive measures.

Influence of nutrient source on specific dynamic action of Pearl Spot, Etroplus suratensis (Bloch)

The magnitude of apparent specific dynamic action (SDA), the maximum rate of oxygen consumption and the length of time that the rate of oxygen uptake remained elevated above the prefeeding level were measured in the Pearl Spot, Etroplus suratensis, fed isonitrous test diets (D 1 - D 4 ) with varying nutrient sources. Irrespective of the diets, the metabolic rate increased immediately after feeding and reached the maximum within 3 to 4 hours. The source of nutrients in the diet significantly altered the magnitude of SDA. It was maximum (91.76% and 129.56%) for those fed on diets D 2 and D 3 and minimum 46.47% and 50.30% for those fed on diets D 1 and D 4 , respectively.

Effect of type of otolith and preparation technique on age estimation of larval and juvenile spot (Leiostomus xanthurus)

Otoliths of larval and juvenile fish provide a record of age, size, growth, and development (Campana and Neilson, 1985; Thorrold and Hare, 2002). However, determining the time of first increment formation in otoliths (Campana, 2001) and assessing the accuracy (deviation from real age) and precision (repeatability of increment counts from the same otolith) of increment counts are prerequisites for using otoliths to study the life history of fish (Campana and Moksness, 1991). For most fish species, first increment deposition occurs either at hatching, a day after hatching, or after first feeding and yolksac absorption (Jones, 1986; Thorrold and Hare, 2002). Increment deposition before hatching also occurs (Barkmann and Beck, 1976; Radtke and Dean, 1982). If first increment deposition does not occur at hatching, the standard procedure is to add a predetermined number to increment counts to estimate fish age (Campana and Neilson, 1985).