Avaluació i implantació d’un sistema de climatització amb energia solar a la Facultat de Ciències de la UdG

Estudi de viabilitat de climatització de la Facultat de Ciències de la UdG per energia solar. Estudi de costos i comparació de l’estalvi respecte al sistema actual

Preparation and characterisation of certain II-VI, I-III-VI2 semiconductor thin films and transparent conducting oxides

There is an increasing demand for renewable energies due to the limited availability of fossil and nuclear fuels and due to growing environmental problems. Photovoltaic (PV) energy conversion has the potential to contribute significantly to the electrical energy generation in the future. Currently, the cost for photovoltaic systems is one of the main obstacles preventing production and application on a large scale. The photovoltaic research is now focused on the development of materials that will allow mass production without compromising on the conversion efficiencies. Among important selection criteria of PV material and in particular for thin films, are a suitable band gap, high absorption coefficient and reproducible deposition processes capable of large-volume and low cost production. The chalcopyrite semiconductor thin films such as Copper indium selenide and Copper indium sulphide are the materials that are being intensively investigated for lowering the cost of solar cells. Conversion efficiencies of 19 % have been reported for laboratory scale solar cell based on CuInSe2 and its alloys. The main objective of this thesis work is to optimise the growth conditions of materials suitable for the fabrication of solar cell, employing cost effective techniques. A typical heterojunction thin film solar cell consists of an absorber layer, buffer layer and transparent conducting contacts. The most appropriate techniques have been used for depositing these different layers, viz; chemical bath deposition for the window layer, flash evaporation and two-stage process for the absorber layer, and RF magnetron sputtering for the transparent conducting layer. Low cost experimental setups were fabricated for selenisation and sulphurisation experiments, and the magnetron gun for the RF sputtering was indigenously fabricated. The films thus grown were characterised using different tools. A powder X-ray diffractometer was used to analyse the crystalline nature of the films. The energy dispersive X-ray analysis (EDX) and scanning electron microscopy i (SEM) were used for evaluating the composition and morphology of the films. Optical properties were investigated using the UV-Vis-NIR spectrophotometer by recording the transmission/absorption spectra. The electrical properties were studied using the two probe and four probe electrical measurements. Nature of conductivity of the films was determined by thermoprobe and thermopower measurements. The deposition conditions and the process parameters were optimised based on these characterisations.

Projecte per la realització d’ una intal·lació solar fotovoltaica en règim especial als edificis de l’ Escola Politècnica Superior de la UdG

El present projecte té per principal odjectiu dur a terme el disseny d’ una instal·lació solar fotovoltaica de producció d’ energia elèctrica en règim especial sobre teulada instal·lada en un edifici de caràcter oficial de l’ Escola Politècnica Superior de la UdG amb l’ objectiu de generar energia elèctrica

Projecte de la intal·lació de calefacció i ACS amb energia solar i caldera de biomassa en un edifici de quatre vivendes.

Projecte de la instal•lació de calefacció i agua calenta utilitzant energia solar tèrmica i ajudant-se d’ una caldera de biomassa en un edifici en construcció situat a Colera (Alt Empordà). Es tracta d’un bloc de quatre vivendes distribuïdes en dues plantes, soterrani i terrassa superior

Projecte d’instal·lacions d’aigua calenta sanitària per a un hotel de quatre estrelles a Platja d’Aro amb aportació d’energia solar

En el present projecte final de carrera s’han dissenyat i pressupostat les instal·lacions de fontaneria, energia solar i gas natural per abastir d’aigua les dependències d’un hotel. L’hotel es troba situat a municipi de Platja d’Aro, a la província de Girona. La seva categoria és de quatre estrelles i això comporta un nivell alt de qualitat en els serveis oferts, en aquest cas el subministrament d’aigua freda i aigua calenta sanitària (ACS) als seus clients

Avaluació i implantació d’un sistema de climatització amb energia solar a la Facultat de Ciències de la UdG

Estudi de viabilitat de climatització de la Facultat de Ciències de la UdG per energia solar. Estudi de costos i comparació de l’estalvi respecte al sistema actual

Instal•lació solar tèrmica i fotovoltaica per a una vivenda aïllada

Aquest projecte va destinat a una família que disposa d’una vivenda aïllada del nucli urbà d’Arenys de Munt, comarca del Maresme, la qual no té al seu abast la connexió del gas ni la de la xarxa elèctrica. S’ha decidit dimensionar la instal•lació per energia solar tèrmica i energia solar fotovoltaica, ja que són energies més constants que l’energia eòlica per a l’indret on ens trobem i a més a més hi ha un mercat que ofereix molts més productes i prestacions

Estudi comparatiu entre un sistema de climatització solar amb planta d’absorció geotèrmica i un sistema de climatització amb bomba de calor geotèrmica

Disseny i dimensionat d’una instal•lació de climatització, durant tot l'any, i comparació entre un sistema de climatització solar amb una planta d’absorció geotèrmica i un sistema de climatització mitjançant una bomba de calor geotèrmica, per al despatx de professors i becaris del nou laboratori d’ energia de l’EPS, mitjançant la utilització d’un sistema d’energia solar tèrmica de baixa temperatura, com a medi d’aportació de calor, i per energia geotèrmica per a la climatització integral

Instal•lació solar tèrmica per la producció d’ACS i climatització de 10 H.P.O. a Quart

Aquesta instal•lació solar tèrmica s’ha dissenyat per cobrir part de les necessitats energètiques d’un edifici que consta de 10 habitatges de protecció oficial construïts en 2 plantes a la localitat de Quart. L’objectiu d’aquest projecte és arribar a una cobertura solar aproximada del 50% de les necessitats d’ aigua calenta sanitària (ACS) i climatització

The impact of installer business models on the uptake of residential microgeneration in the UK: Evidence from a nation-wide survey

This paper arises from a doctoral thesis comparing the impact of alternative installer business models on the rate at which microgeneration is taken up in homes and installation standards across the UK. The paper presents the results of the first large-scale academic survey of businesses certified to install residential microgeneration. The aim is to systematically capture those characteristics which define the business model of each surveyed company, and relate these to the number, location and type of technologies that they install, and the quality of these installations. The methodology comprised a pilot web survey of 235 certified installer businesses, which was carried out in June last year and achieved a response rate of 30%. Following optimisation of the design, the main web survey was emailed to over 2000 businesses between October and December 2011, with 317 valid responses received. The survey is being complemented during summer 2012 by semi-structured interviews with a representative sample of installers who completed the main survey. The survey results are currently being analysed. The early results indicate an emerging and volatile market where solar PV, solar hot water and air source heat pumps are the dominant technologies. Three quarters of respondents are founders of their installer business, while only 22 businesses are owned by another company. Over half of the 317 businesses have five employees or less, while 166 businesses are no more than four years old. In addition, half of the businesses stated that 100% of their employees work on microgeneration-related activities. 85% of the surveyed companies have only one business location in the UK. A third of the businesses are based either in the South West or South East regions of England. This paper outlines the interim results of the survey combined with the outcomes from additional interviews with installers to date. The research identifies some of the business models underpinning microgeneration installers and some of the ways in which installer business models impact on the rate and standards of microgeneration uptake. A tentative conclusion is that installer business models are profoundly dependent on the levels and timing of support from the UK Feed-in Tariffs and Renewable Heat Incentive.

Photovoltaic and solar-assisted ground-source heat pump systems

This review investigates the performance of photovoltaic and solar-assisted ground-source heat pumps in which solar heat is transferred to the ground to improve the coefficient of performance. A number of studies indicate that, for systems with adequately sized ground heat exchangers, the effect on system efficiency is small: about 1% improvement if the heat source is photovoltaic, a 1–2% decline if the source is solar thermal. With possible exceptions for systems in which the ground heat exchanger is undersized, or natural recharge from ground water is insufficient, solar thermal energy is better used for domestic hot water than to recharge ground heat. This appears particularly true outside the heating season, as although much of the heat extracted from the ground can be replaced, it seems to have little effect on the coefficient of performance. Any savings in electrical consumption that do result from an improved coefficient can easily be outweighed by an inefficient control system for the circulation pumps.

LASER-TESTING RIG : Measurement System for evaluation of Shape of concentrating reflector for solar collector Absolicon X10

This Thesis project is a part of the all-round automation of production of concentrating solar PV/T systems Absolicon X10. ABSOLICON Solar Concentrator AB has been invented and started production of the prospective solar concentrated system Absolicon X10. The aims of this Thesis project are designing, assembling, calibrating and putting in operation the automatic measurement system intended to evaluate the shape of concentrating parabolic reflectors.On the basis of the requirements of the company administration and needs of real production process the operation conditions for the Laser testing rig were formulated. The basic concept to use laser radiation was defined.At the first step, the complex design of the whole system was made and division on the parts was defined. After the preliminary conducted simulations the function and operation conditions of the all parts were formulated.At the next steps, the detailed design of all the parts was conducted. Most components were ordered from respective companies. Some of the mechanical components were made in the workshop of the company. All parts of the Laser-testing rig were assembled and tested. Software part, which controls the Laser-testing rig work, was created on the LabVIEW basis. To tune and test software part the special simulator was designed and assembled.When all parts were assembled in the complete system, the Laser-testing rig was tested, calibrated and tuned.In the workshop of Absolicon AB, the trial measurements were conducted and Laser-testing rig was installed in the production line at the plant in Soleftea.

European Solar Engineering School ESES : Past and Future

The European Solar Engineering School ESES is a one-year masters program that started in 1999 at the Solar Energy Research Center SERC, Dalarna University College. It has been growing in popularity over the years, with over 20 students in the current year. Approximately half the students come from Europe, the rest coming from all over the globe. This paper described the contents and experiences from seven years of running the programme and the plans for adapting the programme to the Bologna process. The majority of the students from ESES have found work in the solar industry, energy industry or taken up PhD positions. An alumni group has been started that actively gives support to past, present and potential future students.

Evaluation of a thermally driven heat pump for solar heating and cooling applications

Exploiting solar energy technology for both heating and cooling purposes has the potential of meeting an appreciable portion of the energy demand in buildings throughout the year. By developing an integrated, multi-purpose solar energy system, that can operate all twelve months of the year, a high utilisation factor can be achieved which translates to more economical systems. However, there are still some techno-economic barriers to the general commercialisation and market penetration of such technologies. These are associated with high system and installation costs, significant system complexity, and lack of knowledge of system implementation and expected performance. A sorption heat pump module that can be integrated directly into a solar thermal collector has thus been developed in order to tackle the aforementioned market barriers. This has been designed for the development of cost-effective pre-engineered solar energy system kits that can provide both heating and cooling. This thesis summarises the characterisation studies of the operation of individual sorption modules, sorption module integrated solar collectors and a full solar heating and cooling system employing sorption module integrated collectors. Key performance indicators for the individual sorption modules showed cooling delivery for 6 hours at an average power of 40 W and a temperature lift of 21°C. Upon integration of the sorption modules into a solar collector, measured solar radiation energy to cooling energy conversion efficiencies (solar cooling COP) were between 0.10 and 0.25 with average cooling powers between 90 and 200 W/m2 collector aperture area. Further investigations of the sorption module integrated collectors implementation in a full solar heating and cooling system yielded electrical cooling COP ranging from 1.7 to 12.6 with an average of 10.6 for the test period. Additionally, simulations were performed to determine system energy and cost saving potential for various system sizes over a full year of operation for a 140 m2 single-family dwelling located in Madrid, Spain. Simulations yielded an annual solar fraction of 42% and potential cost savings of €386 per annum for a solar heating and cooling installation employing 20m2 of sorption integrated collectors.