Pharmaceuticals occurrence in a WWTP with significant industrial contribution and its input into the river system

Occurrence and removal of 81 representative Pharmaceutical Active Compounds (PhACs) were assessed in a municipal WWTP located in a highly industrialized area, with partial water reuse after UV tertiary treatment and discharge to a Mediterranean river. Water monitoring was performed in an integrated way at different points in the WWTP and river along three seasons. Consistent differences between therapeutic classes were observed in terms of influent concentration, removal efficiencies and seasonal variation. Conventional (primary and secondary) treatment was unable to completely remove numerous compounds and UV-based tertiary treatment played a complementary role for some of them. Industrial activity influence was highlighted in terms of PhACs presence and seasonal distribution. Even if global WWTP effluent impact on the studied river appeared to be minor, PhACs resulted widespread pollutants in river waters. Contamination can be particularly critical in summer in water scarcity areas, when water flow decreases considerably

Towards integrated operation of membrane bioreactors : effects of aeration on biological and filtration performance

Two experimental studies evaluated the effect of aerobic and membrane aeration changes on sludge properties, biological nutrient removal and filtration processes in a pilot plant membrane bioreactor. The optimal operating conditions were found at an aerobic dissolved oxygen set-point (DO) of 0.5mgO2L-1 and a membrane specific aeration demand (SADm) of 1mh-1, where membrane aeration can be used for nitrification. Under these conditions, a total flow reduction of 42% was achieved (75% energy reduction) without compromising nutrient removal efficiencies, maintaining sludge characteristics and controlled filtration. Below these optimal operating conditions, the nutrient removal efficiency was reduced, increasing 20% for soluble microbial products, 14% for capillarity suction time and reducing a 15% for filterability. Below this DO set-point, fouling increased with a transmembrane pressure 75% higher. SADm below 1mh-1 doubled the values of transmembrane pressure, without recovery after achieving the initial conditions

Non conventional biological treatment based on Trametes versicolor for the elimination of recalcitrant anticancer drugs in hospital wastewater

This work presents a study about the elimination of anticancer drugs, a group of pollutants considered recalcitrant during conventional activated sludge wastewater treatment, using a biological treatment based on the fungus Trametes versicolor. A 10-L fluidized bed bioreactor inoculated with this fungus was set up in order to evaluate the removal of 10 selected anticancer drugs in real hospital wastewater. Almost all the tested anticancer drugs were completely removed from the wastewater at the end of the batch experiment (8 d) with the exception of Ifosfamide and Tamoxifen. These two recalcitrant compounds, together with Cyclophosphamide, were selected for further studies to test their degradability by T. versicolor under optimal growth conditions. Cyclophosphamide and Ifosfamide were inalterable during batch experiments both at high and low concentration, whereas Tamoxifen exhibited a decrease in its concentration along the treatment. Two positional isomers of a hydroxylated form of Tamoxifen were identified during this experiment using a high resolution mass spectrometry based on ultra-high performance chromatography coupled to an Orbitrap detector (LTQ-Velos Orbitrap). Finally the identified transformation products of Tamoxifen were monitored in the bioreactor run with real hospital wastewater

Operation and control of SBR processes for enhanced biological nutrient removal from wastewater

In the last decades, the awareness of environmental issues has increased in society considerably. There is an increasing need to improve the effluent quality of domestic wastewater treatment processes. This thesis describes the application of the Sequencing Batch Reactor (SBR) technology for Biological Nutrient Removal (BNR) from the wastewater. In particular, the work presented evolves from the nitrogen removal to the biological nutrient removal (i.e. nitrogen plus phosphorous removal) with special attention to the operational strategy design, the identification of possible reactor cycle controls or the influent composition related to the process efficiency. In such sense, also the use of ethanol as an external carbon (when low influent Carbon:Phosphorus (C:P) or Carbon:Nitrogen (C:N) ratios are presented) are studied as an alternative to maintain the BNR efficiency.

SBR technology for wastewater treatment: suitable operational conditions for a nutrient removal

Actualment, la legislació ambiental ha esdevingut més restrictiva pel que fa a la descàrrega d'aigües residuals amb nutrients, especialment en les anomenades àrees sensibles o zones vulnerables. Arran d'aquest fet, s'ha estimulat el coneixement, desenvolupament i millora dels processos d'eliminació de nutrients. El Reactor Discontinu Seqüencial (RDS) o Sequencing Batch Reactor (SBR) en anglès, és un sistema de tractament de fangs actius que opera mitjançant un procediment d'omplerta-buidat. En aquest tipus de reactors, l'aigua residual és addicionada en un sol reactor que treballa per càrregues repetint un cicle (seqüència) al llarg del temps. Una de les característiques dels SBR és que totes les diferents operacions (omplerta, reacció, sedimentació i buidat) es donen en un mateix reactor. La tecnologia SBR no és nova d'ara. El fet, és que va aparèixer abans que els sistema de tractament continu de fangs actius. El precursor dels SBR va ser un sistema d'omplerta-buidat que operava en discontinu. Entre els anys 1914 i 1920, varen sorgir certes dificultats moltes d'elles a nivell d'operació (vàlvules, canvis el cabal d'un reactor a un altre, elevat temps d'atenció per l'operari...) per aquests reactors. Però no va ser fins a finals de la dècada dels '50 principis del '60, amb el desenvolupament de nous equipaments i noves tecnologies, quan va tornar a ressorgir l'interès pels SBRs. Importants millores en el camp del subministrament d'aire (vàlvules motoritzades o d'acció pneumàtica) i en el de control (sondes de nivell, mesuradors de cabal, temporitzadors automàtics, microprocessadors) han permès que avui en dia els SBRs competeixin amb els sistemes convencional de fangs actius. L'objectiu de la present tesi és la identificació de les condicions d'operació adequades per un cicle segons el tipus d'aigua residual a l'entrada, les necessitats del tractament i la qualitat desitjada de la sortida utilitzant la tecnologia SBR. Aquestes tres característiques, l'aigua a tractar, les necessitats del tractament i la qualitat final desitjada determinen en gran mesura el tractament a realitzar. Així doncs, per tal d'adequar el tractament a cada tipus d'aigua residual i les seves necessitats, han estat estudiats diferents estratègies d'alimentació. El seguiment del procés es realitza mitjançant mesures on-line de pH, OD i RedOx, els canvis de les quals donen informació sobre l'estat del procés. Alhora un altre paràmetre que es pot calcular a partir de l'oxigen dissolt és la OUR que és una dada complementària als paràmetres esmentats. S'han avaluat les condicions d'operació per eliminar nitrogen d'una aigua residual sintètica utilitzant una estratègia d'alimentació esglaonada, a través de l'estudi de l'efecte del nombre d'alimentacions, la definició de la llargada i el número de fases per cicle, i la identificació dels punts crítics seguint les sondes de pH, OD i RedOx. S'ha aplicat l'estratègia d'alimentació esglaonada a dues aigües residuals diferents: una procedent d'una indústria tèxtil i l'altra, dels lixiviats d'un abocador. En ambdues aigües residuals es va estudiar l'eficiència del procés a partir de les condicions d'operació i de la velocitat del consum d'oxigen. Mentre que en l'aigua residual tèxtil el principal objectiu era eliminar matèria orgànica, en l'aigua procedent dels lixiviats d'abocador era eliminar matèria orgànica i nitrogen. S'han avaluat les condicions d'operació per eliminar nitrogen i fòsfor d'una aigua residual urbana utilitzant una estratègia d'alimentació esglaonada, a través de la definició del número i la llargada de les fases per cicle, i la identificació dels punts crítics seguint les sondes de pH, OD i RedOx. S'ha analitzat la influència del pH i la font de carboni per tal d'eliminar fòsfor d'una aigua sintètica a partir de l'estudi de l'increment de pH a dos reactors amb diferents fonts de carboni i l'estudi de l'efecte de canviar la font de carboni. Tal i com es pot veure al llarg de la tesi, on s'han tractat diferents aigües residuals per a diferents necessitats, un dels avantatges més importants d'un SBR és la seva flexibilitat.

Comportamento do reator seqüencial em batelada (RSB) sob estado estacionário dinâmico utilizando idade do lodo como parâmetro de controle operacional

O reator seqüencial em batelada (RSB) é uma variante de lodos ativados capaz de promover a remoção da matéria orgânica, a remoção dos nutrientes e a separação da fase sólida da líquida em uma unidade. A valorização das áreas urbanas, a carência de tratamento terciário e a crescente necessidade de redução nas dimensões de estações de tratamento de esgoto devem impulsionar o desenvolvimento de pesquisas sobre RSB em curto espaço de tempo. A partir deste cenário, o presente trabalho teve como objetivo modelar o comportamento do reator seqüencial em batelada a partir da teoria desenvolvida por Marais e colaboradores. Dentro deste contexto, a cinética de oxidação dos compostos orgânicos e do nitrogênio na forma amoniacal foi descrita e modelada. O trabalho experimental foi realizado em duas escalas: bancada e piloto. O experimento em escala de bancada foi dividido em duas fases. Foram utilizados dois RSBs e um sistema de fluxo contínuo. Um reator seqüencial em batelada (RSB1) foi operado com idade de lodo. O outro reator em batelada (RSB2) foi operado em função da relação F/M e o sistema de fluxo contínuo (FC1) por idade de lodo. Estes reatores foram utilizados como controle no monitoramento do RSB1 Na primeira fase, os três sistemas removeram apenas matéria orgânica. Na fase seguinte, removeram matéria orgânica e nitrogênio. A partir dos resultados obtidos em escala de bancada, foi possível concluir que o modelo desenvolvido pode ser aplicado ao reator seqüencial em batelada operando com idade de lodo, permitindo determinar a qualidade do efluente, a produção de lodo e o consumo de oxidante. Além disso, foi possível descrever o comportamento da taxa de consumo de oxigênio em função da oxidação da matéria orgânica biodegradável e da oxidação do nitrogênio na forma amoniacal. O reator seqüencial em batelada operado com idade de lodo (RSB1) alcançou remoção média de matéria orgânica de 90 % nas idades de lodo de 30, 20, 10 e 5 dias. A remoção média de nitrogênio mais elevada foi obtida na idade de lodo de 20 dias e atingiu 87 %. Nas demais idades de lodo a remoção média de nitrogênio variou entre 79 e 42 %. A modelagem do comportamento do reator seqüencial em batelada resultou numa proposta de metodologia para o dimensionamento que tem como finalidade abolir critérios obsoletos e inadequados para o dimensionamento de lodos ativados em batelada No experimento em escala piloto, foram utilizados um reator seqüencial em batelada, denominado RSB, e um sistema de fluxo contínuo com a configuração Bardenpho, denominado FC. Os sistemas de lodos ativados sob investigação foram monitorados em duas idades de lodo: 30 e 10 dias. Os dados do experimento em escala piloto mostraram que os processos físico-químicos e biológicos envolvidos na remoção de matéria orgânica e nitrogênio no RSB foram mais eficientes do que no Bardenpho quando trataram o mesmo esgoto doméstico e foram submetidos às mesmas condições operacionais. No RSB, obteve-se 88 e 89 % de remoção de matéria orgânica nas idades de lodo de 10 e 30 dias, respectivamente. Nesta seqüência das idades de lodo, a eficiência do Bardenpho caiu de 87 para 76 %. O sistema de fluxo contínuo removeu 66 e 52 % do nitrogênio total afluente nas idades de lodo de 10 e 30 dias, respectivamente. A eficiência do RSB na remoção de nitrogênio foi determinada apenas na idade de lodo de 10 dias e alcançou 69 %. A partir dos resultados obtidos em escala de bancada e piloto, constata-se que o reator seqüencial em batelada operando com idade de lodo pode ser utilizado no tratamento de esgoto doméstico e obter eficiência na remoção de matéria orgânica e nitrogênio igual ou superior ao sistema de fluxo contínuo.

Eficiência de uma ETE em escala real composta por reator UASB seguido de lodo ativado

In the state of Rio Grande do Norte (RN), Brazil, there are about 80 sewage treatment systems being the predominant technology waste stabilization ponds. The Baldo s WWTP , due to its location and low availability of area, was designed as a hybrid conventional system (UASB reactor followed by activated sludge with biodiscs) at a tertiary level, being the most advanced WWTP in the State and also with the larger treatment capacity (1620 m3/h) .The paper presents the results of its performance based on samples collections from May to December 2012. Composite samples of the effluent of the grit chamber, UASB reactors, anoxic chambers, aeration tanks and treated effluent were collected weekly, every 4 hours for 24 hours. The results showed that the WWTP effluent presented adequate ranges of temperatures, pH and DO, however removal efficiencies of BOD and TSS were below the predicted by design. The UASB reactors also showed removals of BOD and TSS less than expected, due to the accumulation of sludge in the reactors, which eventually, was washed out in the effluent. The nitrification process was not satisfactory mainly due to problems in the oxygen distribution in the aeration tanks. The removal of ammonia and TKN were high, probably by the assimilation process

Avaliação da eficiência da remoção de matéria orgânica e microbiológica de três sistemas de lagoas de estabilização em série na Grande Natal-RN: Beira Rio, Jardim Lola I e Jardim Lola II

Waste stabilization ponds are the main technology in use for domestic sewage treatment in Rio Grande do Norte State (RN), northeast Brazil. The are around 80 systems, constructed mainly by municipal city halls, being series comprised by a primary facultative pond followed by two maturation ponds the most used configuration. Due to problems related with the production and destination of sludge and generation of bad odors, the designers have avoided the use of anaerobic lagoons. The majority of systems are rarely monitored to verify their efficiencies and to get new project parameters for future designing. This work has as purpose to make a diagnosis of efficiency of three series of waste stabilization pond series (WSPS) of Jardim Lola 1, Jardim Lola 2 and Beira Rio, located in the North Zone of the city of the Natal/RN, treating domestic raw sewage, on the removal of organic matter and thermotolerant coliform, comparing the operational conditions of the systems this inside of the bands foreseen in the project, through parameters BOD5, QOD, thermotolerant coliforms, dissolved oxygen, pH, temperature, ammoniac nitrogen, total and suspended solids. The work was carried through in the WSPS, all constituted by a primary facultative pond followed by two maturation ponds. Socioeconomic characteristics of population are predominantly low and all the plants are very near of the contributing basins. The series were monitored from of May the November of 2002, totalizing 20 collections of grab samples of raw sewage and ponds effluents between 8:00 and 9:50 h. The main aspect to be detached by the results was the great concentration of organic matter (BOD and COD) and microorganisms the raw sewage which were around two times more concentrated than those values foreseen one in project. Considering all series the highest removals of organic matter were observed in system Beira Rio (84 and 78% of BOD and COD, respectively), which presented high hydraulic detention time (TDH = 89 days). On the other hand, Jardim Lola 1 and Jardim Lola 2 presented a much lower values of HDT (36 days and 18 days respectively) and their removals of BOD and COD were the same (76% and 60%, respectively). The Beira Rio WSPS, was the most efficient verified in relation to solids and ammonia, proving the great influence of the operational variables such as HDT and applied surface organic loadings on the performance of pond series. Although the treatment plants have reached efficiencies of thermotolerant coliforms around 99,999%, the concentrations in the final effluent can be considered very high for launching in aquatic bodies, particularly those produced by Jardim Lola 1 and Jardim Lola 2 series

Avaliação de lagoas de lemnáceas no polimento de esgoto doméstico e produção de biomassa

Pós-graduação em Engenharia Civil - FEIS

Nova configuração de um reator compartimentado anaeróbio/aeróbio para o tratamento de esgoto sanitário de baixa carga

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da remoção de sulfametoxazol, diclofenaco e 17β-estradiol em água por meio de processo oxidativo com cloro

Pós-graduação em Engenharia Civil - FEIS

Arthrospira platensis biomass with high protein content cultivated in continuous process using urea as nitrogen source

Aims: Arthrospira platensis has been studied for single-cell protein production because of its biomass composition and its ability of growing in alternative media. This work evaluated the effects of different dilution rates (D) and urea concentrations (N0) on A.similar to platensis continuous culture, in terms of growth, kinetic parameters, biomass composition and nitrogen removal. Methods and results: Arthrospira platensis was continuously cultivated in a glass-made vertical column photobioreactor agitated with Rushton turbines. There were used different dilution rates (0.040.44 day-1) and urea concentrations (0.5 and 5 mmol l-1). With N0 = 5 mmol l-1, the maximum steady-state biomass concentration was1415 mg l-1, achieved with D = 0.04 day-1, but the highest protein content (71.9%) was obtained by applying D = 0.12 day-1, attaining a protein productivity of 106.41 mg l-1 day-1. Nitrogen removal reached 99% on steady-state conditions. Conclusions: The best results were achieved by applying N0 = 5 mmol l-1; however, urea led to inhibitory conditions at D = 0.16 day-1, inducing the system wash-out. The agitation afforded satisfactory mixture and did not harm the trichomes structure. Significance and Impact of the Study: These results can enhance the basis for the continuous removal of nitrogenous wastewater pollutants using cyanobacteria, with an easily assembled photobioreactor.

Determination of the intrinsic kinetic parameters of sulfide-oxidizing autotrophic denitrification in differential reactors containing immobilized biomass

Nitrogen removal coupled with sulfide oxidation has potential for the treatment of effluents from anaerobic reactors because they contain sulfide, which can be used as an endogenous electron donor for denitrification. This work evaluated the intrinsic kinetics of sulfide-oxidizing autotrophic denitrification via nitrate and nitrite in systems containing attached cells. Differential reactors were fed with nitrified synthetic domestic sewage and different sulfide concentrations. The intrinsic kinetic parameters of nitrogen removal were determined when the mass transfer resistance was negligible. This bioprocess could be described by a half-order kinetic model for biofilms. The half-order kinetic coefficients ranged from 0.425 to 0.658 mg N-1/2 L-1/2 h(-1) for denitrification via nitrite and from 0.190 to 0.609 mg N-1/2 L-1/2 h(-1) for denitrification via nitrate. In this latter, the lower value was due to the use of electrons donated from intermediary sulfur compounds whose formation and subsequent consumption were detected. (C) 2011 Elsevier Ltd. All rights reserved.

Remoção de matérias orgânica e nitrogenada de esgoto sanitário em reator de leito estruturado, em escala piloto

O processo de nitrificação e desnitrificação simultâneas (NDS) permite alcançar a remoção combinada de matérias carbonácea e nitrogenada em uma única unidade. O reator de leito estruturado, com biomassa imobilizada e recirculação interna, apresenta características positivas para que estes processos envolvidos ocorram, tais como propiciar a formação de biofilme e evitar a colmatação do leito. Esta configuração tem sido estudada com êxito em reatores em escala de bancada para tratamento de esgoto. Nesta pesquisa foi utilizado um reator de leito estruturado em escala piloto com a finalidade de avaliar sua implantação, eficiência e estabilidade tratando esgoto doméstico em condições reais para futura aplicação em pequenas comunidades, condomínios residenciais entre outros como sistema descentralizado. O reator foi construído em fibra de vidro, de formato cilíndrico, com diâmetro interno de aproximadamente 0,80 m e 2,0 m de altura. O volume total foi de aproximadamente 0,905 m3 e o volume útil de 0,642 m3. A operação foi realizada sob condições de aeração contínua e intermitente e os tempos de detenção hidráulica (TDH) testados foram de 48, 36 e 24 horas. A remoção de DQO manteve-se acima de 90% com TDH de 48 e 36 horas. A melhor eficiência de remoção de nitrogênio total foi de 72,4 ± 6,4%, sob TDH de 48 horas e a aeração intermitente, com 2 horas de aeração e 1 hora não aerada. A concentração de oxigênio dissolvido (OD) média de 2,8 ± 0,5 mg.L-1 na fase aerada e temperatura média de 24,7 ± 1,0 °C. Nesse mesmo período, a eficiência média de remoção de DQO foi de 94 ± 4 %. Apesar das dificuldades apresentadas no controle da aeração, as eficiências das remoções obtidas indicaram que o reator de leito estruturado e aeração intermitente (LEAI) se apresenta como uma alternativa promissora em escala plena, requerendo ajustes para construção e incremento da estabilidade da NDS.

A novel wastewater treatment process: Simultaneous nitrification, denitrification and phosphorus removal

Simultaneous nitrification and denitrification (SND) via the nitrite pathway and anaerobic-anoxic enhanced biological phosphorus removal (EBPR) are two processes that can significantly reduce the COD demand for nitrogen and phosphorus removal. The combination of these two processes has the potential of achieving simultaneous nitrogen and phosphorus removal with a minimal requirement for COD. A lab-scale sequencing batch reactor (SBR) was operated in alternating anaerobic-aerobic mode with a low dissolved oxygen concentration (DO, 0.5 mg/L) during the aerobic period, and was demonstrated to accomplish nitrification, denitrification and phosphorus removal. Under anaerobic conditions, COD was taken up and converted to polyhydroxyalkanoates (PHA), accompanied with phosphorus release. In the subsequent aerobic stage, PHA was oxidized and phosphorus was taken up to less than 0.5 mg/L at the end of the cycle. Ammonia was also oxidised during the aerobic period, but without accumulation of nitrite or nitrate in the system, indicating the occurrence of simultaneous nitrification and denitrification. However, off-gas analysis found that the final denitrification product was mainly nitrous oxide (N2O) not N-2. Further experimental results demonstrated that nitrogen removal was via nitrite, not nitrate. These experiments also showed that denitrifying glycogen.-accumulating organisms rather than denitrifying polyphosphate-accumulating organisms were responsible for the denitrification activity.