An evaluation of occupant protection in frontal interior impact for unrestrained front seat occupants of cars and light trucks. Technical report.

Mode of access: Internet.

Rulemaking support paper concerning the 1981-1984 passenger auto average fuel economy standards.

Mode of access: Internet.

Passenger car spark ignition data base. Volume III: miscellaneous data, part I. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington, D.C.

Passenger car spark ignition data base. Volume III: miscellaneous data, part II. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington, D.C.

Quantification of motor vehicle emission factors from on road measurements

Assessment and prediction of the impact of vehicular traffic emissions on air quality and exposure levels requires knowledge of vehicle emission factors. The aim of this study was quantification of emission factors from an on road, over twelve months measurement program conducted at two sites in Brisbane: 1) freeway type (free flowing traffic at about 100 km/h, fleet dominated by small passenger cars - Tora St); and 2) urban busy road with stop/start traffic mode, fleet comprising a significant fraction of heavy duty vehicles - Ipswich Rd. A physical model linking concentrations measured at the road for specific meteorological conditions with motor vehicle emission factors was applied for data analyses. The focus of the study was on submicrometer particles; however the measurements also included supermicrometer particles, PM2.5, carbon monoxide, sulfur dioxide, oxides of nitrogen. The results of the study are summarised in this paper. In particular, the emission factors for submicrometer particles were 6.08 x 1013 and 5.15 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd respectively and for supermicrometer particles for Tora St, 1.48 x 109 particles per vehicle-1 km-1. Emission factors of diesel vehicles at both sites were about an order of magnitude higher than emissions from gasoline powered vehicles. For submicrometer particles and gasoline vehicles the emission factors were 6.08 x 1013 and 4.34 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively, and for diesel vehicles were 5.35 x 1014 and 2.03 x 1014 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively. For supermicrometer particles at Tora St the emission factors were 2.59 x 109 and 1.53 x 1012 particles per vehicle-1 km-1, for gasoline and diesel vehicles, respectively.

Screening to identify large truck potential blackspots : methodological issues and concerns

1. Overview of hotspot identification (HSID)methods 2. Challenges with HSID 3. Bringing crash severity into the ‘mix’ 4. Case Study: Truck Involved Crashes in Arizona 5. Conclusions • Heavy duty trucks have different performance envelopes than passenger cars and have more difficulty weaving, accelerating, and braking • Passenger vehicles have extremely limited sight distance around trucks • Lane and shoulder widths affect truck crash risk more than passenger cars • Using PDOEs to model truck crashes results in a different set of locations to examine for possible engineering and behavioral problems • PDOE models point to higher societal cost locations, whereas frequency models point to higher crash frequency locations • PDOE models are less sensitive to unreported crashes • PDOE models are a great complement to existing practice

Motorcycle riders' self-reported aggression when riding compared with car driving

Aggressive driving has been shown to be related to increased crash risk for car driving. However, less is known about aggressive behaviour and motorcycle riding and whether there are differences in on-road aggression as a function of vehicle type. If such differences exist, these could relate to differences in perceptions of relative vulnerability associated with characteristics of the type of vehicle such as level of protection and performance. Specifically, the relative lack of protection offered by motorcycles may cause riders to feel more vulnerable and therefore to be less aggressive when they are riding compared to when they are driving. This study examined differences in self-reported aggression as a function of two vehicle types: passenger cars and motorcycles. Respondents (n = 247) were all motorcyclists who also drove a car. Results were that scores for the composite driving aggression scale were significantly higher than on the composite riding aggression scale. Regression analyses identified different patterns of predictors for driving aggression from those for riding aggression. Safety attitudes followed by thrill seeking tendencies were the strongest predictors for driving aggression, with more positive safety attitudes being protective while greater thrill seeking was associated with greater self-reported aggressive driving behaviour. For riding aggression, thrill seeking was the strongest predictor (positive relationship), followed by self-rated skill, such that higher self rated skill was protective against riding aggression. Participants who scored at the 85th percentile or above for the aggressive driving and aggressive riding indices had significantly higher scores on thrill seeking, greater intentions to engage in future risk taking, and lower safety attitude scores than other participants. In addition participants with the highest aggressive driving scores also had higher levels of self-reported past traffic offences than other participants. Collectively, these findings suggest that people are less likely to act aggressively when riding a motorcycle than when driving a car, and that those who are the most aggressive drivers are different from those who are the most aggressive riders. However, aggressive riders and drivers appear to present a risk to themselves and others on road. Importantly, the underlying influences for aggressive riding or driving that were identified in this study may be amenable to education and training interventions.

Alternative trajectories for decarbonizing urban transportation

4 p.

A novel measurement of dynamic friction

A tribometer, based on a pin-on-disc machine, uses a PZT drive to produce small sinusoidal fluctuations of sliding speed. The frequency and amplitude of these fluctuations can be controlled, and the dynamic response measured. Preliminary test results show that the dynamic friction variation is influenced by the contact materials, normal force, oscillation frequency and steady sliding speed. The variation of friction force amplitude and phase with frequency gives clues about the underlying state variables determining the friction. Modelling studies illustrate the expected behaviour for idealized friction laws governed by, for example, sliding speed, contact temperature, and "rate-state" laws. © 2008 SAE International.

Fast Response Exhaust Gas Temperature Measurement in IC Engines

The harsh environment presented by engines, particularly in the exhaust systems, often necessitates the use of robust and therefore low bandwidth temperature sensors. Consequently, high frequencies are attenuated in the output. One technique for addressing this problem involves measuring the gas temperature using two sensors with different time-constants and mathematically reconstructing the true gas temperature from the resulting signals. Such a technique has been applied in gas turbine, rocket motor and combustion research. A new reconstruction technique based on difference equations has been developed and its effectiveness proven theoretically. The algorithms have been successfully tested and proven on experimental data from a rig that produces cyclic temperature variations. These tests highlighted that the separation of the thermocouple junctions must be very small to ensure that both sensors are subjected to the same gas temperatures. Exhaust gas temperatures were recorded by an array of thermocouples during transient operation of a high performance two-stroke engine. The results show that the increase in bandwidth arising from the dual sensor technique allowed accurate measurement of exhaust gas temperature with relatively robust thermocouples. Finally, an array of very fine thermocouples (12.5 - 50 microns) was used to measure the in-cycle temperature variation in the exhaust.

Fault Diagnostics for Internal Combustion Engines – Current and Future Techniques

The adoption of each new level of automotive emissions legislation often requires the introduction of additional emissions reduction techniques or the development of existing emissions control systems. This, in turn, usually requires the implementation of new sensors and hardware which must subsequently be monitored by the on-board fault detection systems. The reliable detection and diagnosis of faults in these systems or sensors, which result in the tailpipe emissions rising above the progressively lower failure thresholds, provides enormous challenges for OBD engineers. This paper gives a review of the field of fault detection and diagnostics as used in the automotive industry. Previous work is discussed and particular emphasis is placed on the various strategies and techniques employed. Methodologies such as state estimation, parity equations and parameter estimation are explained with their application within a physical model diagnostic structure. The utilization of symptoms and residuals in the diagnostic process is also discussed. These traditional physical model based diagnostics are investigated in terms of their limitations. The requirements from the OBD legislation are also addressed. Additionally, novel diagnostic techniques, such as principal component analysis (PCA) are also presented as a potential method of achieving the monitoring requirements of current and future OBD legislation.

Technological Learning in Developing Countries

Technological learning refers to the learning processes involved in improving the productive capabilities of an enterprise, sector or economy to enable it to produce higher quality goods or services with increasing levels of efficiency. Approaches to the study of technological learning include case studies of particular countries, sectors and firms; measures of export sophistication; and composite indicators of innovation and competitiveness. The present review draws on these approaches to provide an overview of the policies and practices that have been successful in different regions (East-Asia and Latin America) ; contexts (import substitution and liberalization) ; sectors (pulp and paper, IT services, electronics and passenger cars); and firms (Embrear and Lenovo). While it is clear that there is strong complementarity between domestic technological capability and the ability to absorb foreign technology, there is no simple policy recipe which is appropriate for all times, industries or places. Technological learning builds on and is shaped by what is already known. It requires time, space and resources all of which are influenced by the wider domestic and international context. The current international context is challenging but countries and firms have to find ways of moving forward despite the limited strategy space.

Assessment of the impact speed and angle conditions for the EN1317 barrier tests

Roadside safety barriers designs are tested with passenger cars in Europe using standard EN1317 in which the impact angle for normal, high and very high containment level tests is 20°. In comparison to EN1317, the US standard MASH has higher impact angles for cars and pickups (25°) and different vehicle masses. Studies in Europe (RISER) and the US have shown values for the 90th percentile impact angle of 30°–34°. Thus, the limited evidence available suggests that the 20° angle applied in EN 1317 may be too low.
The first goal of this paper is to use the US NCHRP database (Project NCHRP 17–22) to assess the distribution of impact angle and collision speed in recent ROR accidents. Second, based on the findings of the statistical analysis and on analysis of impact angles and speeds in the literature, an LS-DYNA finite element analysis was carried out to evaluate the normal containment level of concrete barriers in non-standard collisions. The FE model was validated against a crash test of a portable concrete barrier carried out at the UK Transport Research Laboratory (TRL).
The accident data analysis for run-off road accidents indicates that a substantial proportion of accidents have an impact angle in excess of 20°. The baseline LS-DYNA model showed good comparison with experimental acceleration severity index (ASI) data and the parametric analysis indicates a very significant influence of impact angle on ASI. Accordingly, a review of European run-off road accidents and the configuration of EN 1317 should be performed.

Avaliação do desempenho de ligações tubulares em estruturas de veículos pesados de passageiros por simulação numérica

Nesta Dissertação ir-se-á avaliar o desempenho de algumas ligações existentes nos veículos pesados de passageiros, através do Regulamento Eurocódigo 3. Nos últimos anos ocorreram diversos acidentes envolvendo este tipos de veículos, em que os mesmos causaram vítimas mortais e feridos graves. Serão testadas por simulação numérica algumas ligações pertencentes a elementos constituintes da superestrutura, em que esta é normalmente afectada com a ocorrência de acidentes. Assim sendo, o estudo de nós de ligação tem uma importância fulcral para que uma superestrutura suporte situações extremas e que resista a solicitações externas aplicadas. Iniciou-se esta Dissertação com o estudo da sinistralidade e de acidentes que envolvem veículos pesados de passageiros. No capítulo 2 abordou-se um programa que promove simulações numéricas de acidentes e estudo do comportamento dos passageiros em caso de acidente, sendo referido o Regulamento que homologa os veículos pesados de passageiros e os seus principais métodos. Abordaram-se os principais constituintes da estrutura de um veículo pesado de passageiros. No capítulo 3, é referido o Eurocódigo 3 em termos do estudo das ligações tubulares usadas neste tipo de veículos. No capítulo 4, fez-se o estudo e selecção de elementos a utilizar para a simulação numérica de casos preconizados pelo Eurocódigo 3 e estudaram-se três tipos de ligações que são usadas na construção da superestrutura deste tipo de veículos, tendo-se retirado conclusões deste estudo.

Seat in China

Currently, China has the biggest automobile industry in the world. China’s economic situation helped the automobile market, as the internal demand of passenger cars increased substantially in the last years. Chinese automobile industry’s astonishing expansion over the past years has attracted many foreign automobile groups. SEAT decided to enter the Chinese market, following its expansion strategy to enter new markets. The purpose of this study is to analyse and understand the strategic entry of SEAT in the Chinese market, hence the choice of an explanatory case study (Yin, 2003). This study extends this analysis by examining the chines automobile market, more specifically the demand, the market segmentation and the intensity of competition, reviewing the SEAT company history, their competitive positioning and resources. I conclude that, although the Chinese market has growing potential, SEAT has failed to achieve its initial objective. The company has not been able to create a brand awareness in the Chinese market, unlike other foreign brands that have managed to accomplish that. This occurred, mostly, because of the high prices in comparison to its competitors due to additional import cost, such as import duties, transportation and distribution.